Nanocellulose-based tannin-immobilized biosorbent for efficient copper ion removal.

Tannins, which are water-soluble polyhydroxyphenols found in plant structures, offer a sustainable alternative to inorganic products for treating effluents. To overcome their solubility in water, new methods have been developed to immobilize tannin on materials such as nanocellulose, resulting in tannin-based adsorbents. This study investigates the production of different types of tannin-based adsorbents immobilized on nanocellulose nanofibrils using glutaraldehyde as a crosslinking agent. The adsorbents were characterized for their morphology, chemical composition, tannin leaching, thermal stability, and copper adsorption capacity. The main results showed that tannin leaching from the adsorbents in water was greatly reduced with glutaraldehyde. Scanning electron microscopy images showed tannin coating on the surface of nanocellulose nanofibrils due to immobilization. The lyophilized adsorbent was effective in adsorbing Cu (II) within 1 min, with the adsorbed amount increasing gradually until stabilization after 45 min. Overall, this study suggests that tannin immobilized on nanofibrillated cellulose has the potential to offer a sustainable and renewable alternative for effluent treatment.

Alternative methods for the pilot-scale production and characterization of chitosan nanoparticles.

This work describes the production/characterization of low molar mass chitosan nanoparticles derived from waste shrimp shells (SSC), as well as from a commercial chitosan (CC). The production of low molar mass nanochitosan employed thermal shock, alternating between 100 °C and ambient temperature, followed by grinding the dry material (SSC and CC) in a ball mill, producing around 500 g of nanochitosan per batch. A highlight of the methodology employed is that it enables nanochitosan to be obtained even from a low quality commercial raw material. All particles had diameters smaller than 223 nm, with an average diameter below 25 nm (determined by DLS), while reductions of molar mass were between 8.4-fold and 13.5-fold. The depolymerization process resulted in a reduction in crystallinity of 38.1 to 25.4% and 55.6 to 25.9% in the CC and SSC samples, respectively. The production of nanochitosans was also confirmed by TEM through the observation of crystalline domains with diameters between 5 and 10 nm. This work perfectly reproduces the results on bench scale from previous research. The simple and inexpensive processes enable easy scale-up, representing an important advance in the production chain of biopolymers. Graphical abstract.

Nanocellulose obtained from residues of peach palm extraction (Bactris gasipaes).

The large amount of residues generated by the peach palm agroindustry and its cellulose content (34 g 100g-1) motivated the present investigation, where outer sheaths were used for nanocellulose production through ultrafine grinding. Protocols combining different chemical delignification with defibrillation intensity (10 and 20 cycles) were applied and their influence over some properties and characteristics of nanofibers evaluated. At all protocols applied it was possible produce cellulose at nanometric level (widths ˜100 nm), with high crystallinity index (49.8-54.5%) and great thermal stability. The delignification influenced the defibrillation, where lignin removal resulted in well dispersed bundles of fibrils with lower widths. Lower lignin contents combined with higher shear forces released more nanofibrils, with more adsorbed water with defibrillation extension. These behavior influenced the suspension stability, that was higher at larger number of cycles (20). The results evidenced that was possible produced FNC with appropriate technical characteristics from pupunha discards.

Adsorption of aquaculture pollutants using a sustainable biopolymer.

Intensive aquaculture needs to adopt techniques that are able to contribute towards sustainability. Closed systems that employ water recirculation can combine intensive production with environmental sustainability, since there is no exchange of water or discharge of effluents into the environment. In order to achieve this, effective filtration systems are required to ensure that the water quality is satisfactory for the cultivation of aquatic organisms. Chitosan, an industrial waste material derived from crustacean farming, is a renewable natural material that is biodegradable and possesses adsorbent characteristics. In this work, chitosan foam was incorporated in filters and was evaluated as an adsorbent of aquaculture pollutants, adding value to the material and at the same time providing a use for industrial waste. The foam was characterized by scanning electron microscopy and energy dispersive spectroscopy, apparent density, and water absorption capacity. It was used to remove ammonia, nitrite, orthophosphate, and turbidity from aquaculture effluents. The foam consisted of a bilayer with smooth and porous sides, which presented low density, flexibility, and high water absorption capacity. The best proportion of the foam, in terms of the mass of foam per volume of solution (% m v-1), was 0.10, which resulted in removal of 32.8, 57.2, 89.5, and 99.9% of ammonia, nitrite, orthophosphate, and turbidity, respectively. This biopolymer produced is biodegradable, and when saturated with organic compounds from aquaculture, and no longer suitable for reuse as a filter material, it can be employed as a fertilizer, hence closing the sustainability cycle of the aquaculture production chain.