Crosslinking of chitosan films processed by compression molding.

An alternative approach towards more sustainable chitosan films, through their manufacture by thermo-compression molding, was explore in this work. This strategy permitted the reduction of production times and avoided the use of organic solvents since biopolymer and acid were mixed in their solid form. Furthermore, the acid used as a crosslinker was citric acid, a natural policarboxylic acid, which promoted the reaction with chitosan, as shown by Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). This crosslinking reaction led to the formation of homogeneous structures, as observed by scanning electron microscopy (SEM), indicating a good compatibility among all the components of the mixture and enhancing the mechanical properties of the resulting films. In particular, an increase of 80% for tensile strength and an increase of 3000% for elongation at break were observed for the crosslinked films. In addition to the homogeneous surface of citric acid-incorporated films, all the films showed hydrophobic character and the addition of citric acid led to a more amorphous structure. In sum, citric acid-incorporated chitosan films manufactured by compression molding were found to show potential for food and pharmaceutical applications.

Lactose-crosslinked fish gelatin-based porous scaffolds embedded with tetrahydrocurcumin for cartilage regeneration.

Tetrahydrocurcumin (THC) is one of the major colourless metabolites of curcumin and shows even greater pharmacological and physiological benefits. The aim of this work was the manufacturing of porous scaffolds as a carrier of THC under physiological conditions. Fish-derived gelatin scaffolds were prepared by freeze-drying by two solutions concentrations (2.5% and 4% w/v), cross-linked via addition of lactose and heat-treated at 105 °C. This cross-linking reaction resulted in more water resistant scaffolds with a water uptake capacity higher than 800%. Along with the cross-linking reaction, the gelatin concentration affected the scaffold morphology, as observed by scanning electron microscopy images, by obtaining a reduced porosity but larger pores sizes when the initial gelatin concentration was increased. These morphological changes led to a scaffold's strength enhancement from 0.92 ±â€¯0.22 MPa to 2.04 ±â€¯0.18 MPa when gelatin concentration was increased. THC release slowed down when gelatin concentration increased from 2.5 to 4% w/v, showing a controlled profile within 96 h. Preliminary in vitro test with chondrocytes on scaffolds with 4% w/v gelatin offered higher metabolic activities and cell survival up to 14 days of incubation. Finally the addition of THC did not influence significantly the cytocompatibility and potential antibacterial properties were demonstrated successfully against Staphylococcus aureus.

Chitosan as a bioactive polymer: Processing, properties and applications.

Chitin is one of the most abundant natural polysaccharides in the world and it is mainly used for the production of chitosan by a deacetylation process. Chitosan is a bioactive polymer with a wide variety of applications due to its functional properties such as antibacterial activity, non-toxicity, ease of modification, and biodegradability. This review summarizes the most common chitosan processing methods and highlights some applications of chitosan in various industrial and biomedical fields. Finally, environmental concerns of chitosan-based films, considering the stages from raw materials extraction up to the end of life after disposal, are also discussed with the aim of finding more eco-friendly alternatives.

Characterization of agar/soy protein biocomposite films: Effect of agar on the extruded pellets and compression moulded films.

Agar/soy protein biocomposite films were successfully processed by extrusion and compression moulding, obtaining transparent and homogeneous films. The conformational changes occurred during the extrusion process and the effect of agar on the final properties were analyzed. As shown by differential scanning calorimetry (DSC) and specific mechanical energy (SME) values, during the extrusion process protein denatured and unfolded protein chains could interact with agar. These interactions were analyzed by Fourier transform infrared spectroscopy (FTIR) and the secondary structure was determined from the amide I band. Those interactions were supported by the decrease of film solubility. Furthermore, the good compatibility between agar and soy protein was confirmed by the images from scanning electron microscopy (SEM).

Extraction of agar from Gelidium sesquipedale (Rhodopyta) and surface characterization of agar based films.

The chemical structure of the agar obtained from Gelidium sesquipedale (Rhodophyta) has been determined by (13)C nuclear magnetic resonance ((13)C NMR) and Fourier transform infrared spectroscopy (FTIR). Agar (AG) films with different amounts of soy protein isolate (SPI) were prepared using a thermo-moulding method, and transparent and hydrophobic films were obtained and characterized. FTIR analysis provided a detailed description of the binding groups present in the films, such as carboxylic, hydroxyl and sulfonate groups, while the surface composition was examined using X-ray photoelectron spectroscopy (XPS). The changes observed by FTIR and XPS spectra suggested interactions between functional groups of agar and SPI. This is a novel approach to the characterization of agar-based films and provides knowledge about the compatibility of agar and soy protein for further investigation of the functional properties of biodegradable films based on these biopolymers.

Functional properties of chitosan-based films.

Chitosan-based films plasticized with glycerol were prepared by casting with the aim to obtain environmentally friendly materials for packaging applications. Different contents of glycerol were incorporated into chitosan solutions to improve mechanical properties and all films obtained were flexible and transparent. It was observed that the transparency and good behaviour of the films against UV radiation were not affected by chitosan molecular weight or glycerol content. Moreover, chitosan-based films exhibited excellent barrier properties against water vapour and oxygen, even with the addition of glycerol. The effect of the plasticizer on the properties has been explained using Fourier transform infrared (FTIR) spectroscopic analysis. The changes observed in the intensity of the bands showed that glycerol interacts with chitosan, which could be confirmed by total soluble matter (TSM).