Multi-acrylamides improve bond stability through collagen reinforcement under physiological conditions.

OBJECTIVES: Acrylamides were shown to significantly improve bonding stability in adhesive restorations, but the reinforcement mechanism has not been fully elucidated. We tested the hypothesis that hydrogen bonding reinforcement of the collagen network (with secondary or tertiary acrylamides), as well as degree of crosslinking of the polymer network (with di- or tri-functional acrylamides), can be two of the factors at play. METHODS: Two-step total etch adhesives comprising UDMA (60 wt%) and 40 wt% of: TAAEA, TMAAEA (secondary, tertiary tri-acrylamides), BAAP, DEBAAP (secondary, tertiary di-acrylamides) or HEMA (mono-methacrylate - control) were formulated. Simulated composite restorations (n = 5) were tested after cyclic mechanical and biological (S. mutans biofilm) challenges. Gap formation before and after aging was assessed with SEM imaging. Micro-tensile bond strength (µTBS, n = 6) was assessed after seven-day incubation in water or S. mutans-containing culture medium. Collagen reinforcement was assessed with hydroxyproline assay (n = 10) and rheology (n = 3). Data were analyzed with one-way/two-way ANOVA/Tukey's test (alpha=5%). RESULTS: Gap formation increased and bond strength decreased for all monomers after biofilm incubation (p < 0.001). Except for DEBAAP, secondary and tertiary di/tri-acrylamides showed lower occlusal gap width values, but no significant differences overall gap length compared to HEMA. µTBS increased for tri-acrylamides compared with HEMA. Samples treated with multi-acrylamides had lower concentration of hydroxyproline (by-product of collagen degradation) (p < 0.001), except for DEBAAP, which showed values close to HEMA (p > 0.05). Dentin shear modulus increased for all acrylamides after 72 h, especially TMAAEA. SIGNIFICANCE: In general, multi-acrylamides promote collagen reinforcement, leading to reduced gap formation, and stabilize the bond strength under physiological conditions.

Microtensile Bond Strength and Failure Mode of Different Universal Adhesives on Human Dentin.

AIM: The aim of this study was to compare the microtensile bond strength (µTBS) and failure mode of 4 different universal adhesive systems (UAs) on human dentin. MATERIALS AND METHODS: The study sectioned the occlusal thirds of 32 human third molars and divided them into 4 groups based on the adhesive system used. Group A: Palfique Universal Bond, Group B: Single Bond Universal, Group C: All-Bond Universal, and Group D: One Coat 7 Universal. The specimens underwent a 10,000-cycle thermocycling ageing process prior to testing (n = 32). Afterwards, 8 beams were obtained per group and subjected to µTBS testing using a digital universal testing machine at a speed of 1 mm/min. The microtensile bond strength values were analysed in Megapascals (MPa), and the failure mode was evaluated using a stereomicroscope. Welch's parametric ANOVA with robust variance and the Games-Howell post hoc test were used for µTBS comparisons, and Fisher's exact test was used to determine the association between adhesive type and failure mode. The significance level was set at P < .05. RESULTS: Group D showed a significantly higher µTBS than groups A (P < .001) and B (P < .001), but no significant difference was observed with group C (P= .075). Furthermore, groups B and C showed significantly higher µTBS than group A (P< .001 and P < .001, respectively), but there was no significant difference between groups B and C (P = .132). Additionally, group A exhibited a significant association with an adhesive failure mode (P < .05), whereas groups B, C, and D were significantly associated with a mixed failure mode (P < .05). CONCLUSION: The One Coat 7 Universal adhesive system showed higher microtensile bond strength values and higher chemical interaction with dentin compared to Palfique Universal Bond and Single Bond Universal. However, no significant differences were observed compared to All-Bond Universal.

Tensile strength of adhesives in peripheral nerve anastomoses: an in vitro biomechanical evaluation of four different neurorrhaphies.

BACKGROUND: The fundamental prerequisite for prognostically favorable postoperative results of peripheral nerve repair is stable neurorrhaphy without interruption and gap formation. METHODS: This study evaluates 60 neurorrhaphies on femoral chicken nerves in terms of the procedure and the biomechanical properties. Sutured neurorrhaphies (n = 15) served as control and three sutureless adhesive-based nerve repair techniques: Fibrin glue (n = 15), Histoacryl glue (n = 15), and the novel polyurethane adhesive VIVO (n = 15). Tensile and elongation tests of neurorrhaphies were performed on a tensile testing machine at a displacement rate of 20 mm/min until failure. The maximum tensile force and elongation were recorded. RESULTS: All adhesive-based neurorrhaphies were significant faster in preparation compared to sutured anastomoses (p < 0.001). Neurorrhaphies by sutured (102.8 [cN]; p < 0.001), Histoacryl (91.5 [cN]; p < 0.001) and VIVO (45.47 [cN]; p < 0.05) withstood significant higher longitudinal tensile forces compared to fibrin glue (10.55 [cN]). VIVO, with △L/L0 of 6.96 [%], showed significantly higher elongation (p < 0.001) compared to neurorrhaphy using fibrin glue. CONCLUSION: Within the limitations of an in vitro study the adhesive-based neurorrhaphy technique with VIVO and Histoacryl have the biomechanical potential to offer alternatives to sutured neuroanastomosis because of their stability, and faster handling. Further in vivo studies are required to evaluate functional outcomes and confirm safety.

Effect of Simulated Dental Pulpal Pressure Using Fetal Bovine Serum for the Bonding Performance of Contemporary Adhesive to Dentin.

This study evaluated the effect of simulated pulpal pressure (SPP) conditions and storage time on contemporary adhesive systems' microtensile bond strength (µTBS) to dentin. Extracted human molars were prepared and randomly divided into four groups according to the adhesives: Clearfil Megabond 2 (CSE), Beautibond Xtreme Universal (BXU), G2-Bond (G2B), and Scotchbond Universal Plus (SBP). Each adhesive group was further divided following the SPP conditions: control with no simulation (SPP-CTR), SPP with distilled water (SPP-DTW), and SPP with fetal bovine serum (SPP-FBS). Resin composite build-ups were prepared, and teeth were stored in water (37 °C) for 24 h (24 h) and 3 months (3 m). Then, teeth were sectioned to obtain resin-dentin bonded beams and tested to determine the µTBS. Data were analyzed using three-way ANOVA, Tukey post hoc tests (=0.05), and Weibull failure analysis. Failure mode was observed using scanning electron microscopy. The µTBS response was affected by adhesive systems, simulated pulpal pressure conditions, and storage time. SPP-CTR groups presented a higher overall bond strength than SPP-DTW and SPP-FBS, which were not significantly different from each other. Only for SBP, the SPP-FBS group showed higher µTBS than the SPP-DTW group. The Weibull analysis showed that the bonding reliability and durability under SPP-DTW and SPP-FBS were inferior to SPP-CTR, and the 24 h bonding quality of adhesives to dentin was superior to that of 3 m. SPP drastically reduced the µTBS of all adhesives to dentin regardless of solution (distilled water or fetal bovine serum). Storage after 3 m also decreased µTBS despite the SPP condition.

Effects of dentin bonding agents and silanization on bond strength between 3D printed resin and composite resin.

This study aimed to evaluate the effects of dentin bonding agents and silanization on the bond strength between 3D printed resin and composite resin and compare it with a conventional composite resin. 3D printed resin cylinders (PCB) and composite resin substrates (Z250) were prepared and divided into eight subgroups based on the bonding agents used (n=12). The shear bond strength was measured using a universal testing machine, and the failure modes were evaluated. The bond strength was found to vary significantly among the bonding agents and substrate types. Silane application did not significantly improve the bond strength. Among the bonding agents, the universal adhesives exhibited the highest bond strengths for both substrates. Compared to PCB, Z250 demonstrated stronger bonds and exhibited more cohesive failures. Further research is needed to optimize the surface treatments and resin formulations for enhanced bond strength and durability between 3D printed and composite resins.

Engineering injectable hyaluronic acid-based adhesive hydrogels with anchored PRP to pattern the micro-environment to accelerate diabetic wound healing.

Diabetic wounds remain a global challenge due to disordered wound healing led by inflammation, infection, oxidative stress, and delayed proliferation. Therefore, an ideal wound dressing for diabetic wounds not only needs tissue adhesiveness, injectability, and self-healing properties but also needs a full regulation of the microenvironment. In this work, adhesive wound dressings (HA-DA/PRP) with injectability were fabricated by combining platelet rich plasma (PRP) and dopamine-modified-hyaluronic acid (HA-DA). The engineered wound dressings exhibited tissue adhesiveness, rapid self-healing, and shape adaptability, thereby enhancing stability and adaptability to irregular wounds. The in vitro experiments demonstrated that HA-DA/PRP adhesives significantly promoted fibroblast proliferation and migration, attributed to the loaded PRP. The adhesives showed antibacterial properties against both gram-positive and negative bacteria. Moreover, in vitro experiments confirmed that HA-DA/PRP adhesives effectively mitigated oxidative stress and inflammation. Finally, HA-DA/PRP accelerated the healing of diabetic wounds by inhibiting bacterial growth, promoting granulation tissue regeneration, accelerating neovascularization, facilitating collagen deposition, and modulating inflammation through inducing M1 to M2 polarization, in an in vivo model of infected diabetic wounds. Overall, HA-DA/PRP adhesives with the ability to comprehensively regulate the microenvironment in diabetic wounds may provide a novel approach to expedite the diabetic wounds healing in clinic.

Bond strength and marginal adaptation of resin composites and correlations with clinical results.

OBJECTIVES: Due to innumerable confounding factors and a high number of types and brands of dental restorative materials, the clinical performance of restorative materials are sought predicted by various in vitro tests. However, only few such tests have been found to correlate well with clinical findings. Thus, the present study determined the in vitro dentin bond strength and marginal adaptation of Class II restorations and correlated the results to their clinical outcomes. METHODS: Dentin bond strength (µTBS and µSBS) and marginal gap formation of Class II restorations (replica technique and SEM) were measured after 24 h and 6 m water storage using eight combinations of adhesive and resin composite. Clinical outcomes (mean survival time, Hazard Ratio, annual failure rate; n = 10.695) were gained from a data set of a retrospective multicenter study of direct restorations. RESULTS: Significant differences were found for dentin bond strength and marginal gap formation between the restorative material groups, and negative effects of long-term storage were observed. µTBS correlated significantly with certain clinical outcomes of Class I restorations, while µSBS correlated with certain clinical outcomes of Class II, III, IV and V restorations. Marginal gap formation in enamel and number of paramarginal fractures correlated with certain clinical outcomes of Class II restorations. SIGNIFICANCE: Using the same restorative materials in vitro as in vivo, gave significant, but weak correlations between in vitro bond strength or marginal adaptation and clinical outcomes, lending support to the use of in vitro tests in early stages of material selection.

Polymers in 3D printing of external maxillofacial prostheses and in their retention systems.

Maxillofacial defects, arising from trauma, oncological disease or congenital abnormalities, detrimentally affect daily life. Prosthetic repair offers the aesthetic and functional reconstruction with the help of materials mimicking natural tissues. 3D polymer printing enables the design of patient-specific prostheses with high structural complexity, as well as rapid and low-cost fabrication on-demand. However, 3D printing for prosthetics is still in the early stage of development and faces various challenges for widespread use. This is because the most suitable polymers for maxillofacial restoration are soft materials that do not have the required printability, mechanical strength of the printed parts, as well as functionality. This review focuses on the challenges and opportunities of 3D printing techniques for production of polymer maxillofacial prostheses using computer-aided design and modeling software. Review discusses the widely used polymers, as well as their blends and composites, which meet the most important assessment criteria, such as the physicochemical, biological, aesthetic properties and processability in 3D printing. In addition, strategies for improving the polymer properties, such as their printability, mechanical strength, and their ability to print multimaterial and architectural structures are highlighted. The current state of the prosthetic retention system is presented with a focus on actively used polymer adhesives and the recently implemented prosthesis-supporting osseointegrated implants, with an emphasis on their creation from 3D-printed polymers. The successful prosthetics is discussed in terms of the specificity of polymer materials at the restoration site. The approaches and technological prospects are also explored through the examples of the nasal, auricle and ocular prostheses, ranging from prototypes to end-use products.

Dynamic injectable tissue adhesives with strong adhesion and rapid self-healing for regeneration of large muscle injury.

Wounds often necessitate the use of instructive biomaterials to facilitate effective healing. Yet, consistently filling the wound and retaining the material in place presents notable challenges. Here, we develop a new class of injectable tissue adhesives by leveraging the dynamic crosslinking chemistry of Schiff base reactions. These adhesives demonstrate outstanding mechanical properties, especially in regard to stretchability and self-healing capacity, and biodegradability. Furthermore, they also form robust adhesion to biological tissues. Their therapeutic potential was evaluated in a rodent model of volumetric muscle loss (VML). Ultrasound imaging confirmed that the adhesives remained within the wound site, effectively filled the void, and degraded at a rate comparable to the healing process. Histological analysis indicated that the adhesives facilitated muscle fiber and blood vessel formation, and induced anti-inflammatory macrophages. Notably, the injured muscles of mice treated with the adhesives displayed increased weight and higher force generation than the control groups. This approach to adhesive design paves the way for the next generation of medical adhesives in tissue repair.

Small Ionic-Liquid-Based Molecule Drives Strong Adhesives.

Nature has inspired scientists to fabricate adhesive materials for applications in many burgeoning areas. However, it is still a significant challenge to develop small-molecule adhesives with high-strength, low-temperature and recyclable properties, although these merits are of great interest in various aspects. Herein, we report a series of strong adhesives based on low-molecular-weight molecular solids driven by the terminal modification of ionic liquids (ILs) and subsequent supramolecular self-assembly. The emergence of high strength and liquid-to-solid transitions for these supramolecular aggregates relies on modifying IL with a high melting point motif and enriching the types of noncovalent interactions in the original ILs. Using this strategy, we demonstrate that our IL-based molecular solids can efficiently obtain a high adhesion strength (up to 8.95 MPa). Importantly, we elucidate the mechanism underlying the reversible and strong adhesion enabled by monomer-to-polymer transitions. These fundamental findings provide guidance for the design of high-performance supramolecular adhesive materials.

Association of Surgical Adhesive and Glue System With Incidence of Allergic Dermatitis Post Unilateral and Staged Bilateral Total Knee Arthroplasty.

Background Skin closure is an important step in total knee arthroplasty (TKA). Several techniques are described in the literature with emerging interest in skin adhesives. This study aims to highlight the adverse reactions related to skin adhesives and to identify potential risk factors. Methods A retrospective review of 250 patients (295 knees, 45 being staged bilateral TKA) who underwent TKA was conducted at our facility. All patients underwent the same perioperative protocol with application of surgical glue over the wound edges. Postoperative adverse reactions were classified as allergic dermatitis (AD), cellulitis, and superficial infection. Results Incidence of adverse reactions in the form of AD was noted in 4.8% of patients. Demographics and comorbidities had no influence on this occurrence (p>0.05). However, in patients who had bilateral staged TKA, AD manifested after performing the second contralateral TKA in 22% of patients. This incidence of AD was significantly higher when compared to those who had single unilateral TKA (p =0.001) Conclusion The theory of allergic sensitization may explain the higher incidence of AD in bilateral staged TKA due to prior exposure to glue components in the first knee; thus, we recommend avoiding its use if there was previous exposure.

pH-regulated Tannic acid and soybean protein isolate adhesive for enhanced performance in plant-based meat analogues.

A food adhesive comprising tannic acid (TA) and soybean protein isolate (SPI) was developed to establish a cohesive bond between soy protein gel and simulated fat. The impact of varying TA concentrations and pH levels on the adhesive's rheology, thermal stability, chemical structure, and tensile strength were investigated. Rheological results revealed a gradual decrease in adhesive viscosity with increasing TA content. Differential scanning calorimetry (DSC) and thermal gravimetric (TG) results indicated that the stability of the adhesive improved with higher TA concentrations, reaching its peak at 0.50% TA addition. The incorporation of TA resulted in the cross-linking of amino group in unfolded SPI molecules, forming a mesh structure. However, under alkaline conditions (pH 9), adhesive viscosity and stability increased compared to the original pH. This shift was due to the disruption of the SPI colloidal charge structure, an increase in the stretching of functional groups, further unfolding of the structure, and an enhanced binding of SPI to TA. Under the initial pH conditions, SPI reacted with TA's active site to form covalent crosslinked networks and hydrogen bonds. In alkaline condition, beyond hydrogen and ionic bonding, the catechol structure was oxidized, forming an ortho-quinone that crosslinked SPI and created a denser structure. Tensile strength measurements and freeze-thaw experiments revealed that the adhesive exhibited maximum tensile strength and optimal adhesion with 0.75% TA at pH 9, providing the best overall performance. This study provides a new formulation and approach for developing plant-based meat analogues adhesives.

Efficacy of Endoscopic Tissue Adhesive in Patients with Gastrointestinal Tumor Bleeding.

BACKGROUND: Gastrointestinal tumors bleeding remains a significantly clinical challenge due to its resistance to conventional endoscopic hemostasis methods. While the efficacy of endoscopic tissue adhesives (ETA) in variceal bleeding has been established, its role in gastrointestinal tumor bleeding (GITB) remains ambiguous. AIMS: This study aims to assess the feasibility and effectiveness of ETA in the treatment of GITB. METHODS: The study enrolled 30 patients with GITB who underwent hemostasis through Histoacryl® tissue glue injection. Hemostasis success rates, ETA-related adverse events, and re-bleeding rates were evaluated. RESULTS: ETA application achieved successful hemostasis at all tumor bleeding sites, with immediate hemostasis observed in all 30 (100.0%) patients. Among the initially hemostasis cases, 5 patients (17.0%) experienced re-bleeding within 30 days, and the 60 day re-bleeding rate was 20.0% (6/30). Expect for one case of vascular embolism, no adverse events related with ETA application were reported. The 6 month survival was 93%. CONCLUSION: ETA demonstrated excellent immediate hemostasis success rate in GITB cases and showed promising outcomes in prevention re-bleeding.

Development of mucoadhesive microspheres for intranasal delivery of fluconazole as an alternative treatment of cryptococcal meningitis infection in patients with acquired immunodeficiency.

INTRODUCTION: Cryptococcal meningitis is a deadly disease with few treatment options. Its incidence is still high and closely linked to the HIV/AIDS epidemic. This study aimed to develop a mucoadhesive microsphere delivery system for fluconazole for the intranasal route. METHOD: Microspheres of mucoadhesive fluconazole formulation variables such as different amounts of drug concentration and polymer concentration were prepared by a simple emulsion-crosslinking method. The prepared microspheres' surface was characterised by SEM (Scanning electron microscopy) and evaluated for particle size, entrapment efficiency, production yield, infrared spectroscopic study, in-vitro muco-adhesion, and in-vitro drug release. RESULTS: The results showed that formula 1 is the optimal mucoadhesive microsphere preparation, with a particle size of 56.375m, a spherical surface shape, an entrapment efficiency of 99.96%, and a greater mucoadhesive capability during 6-hour evaluation. Furthermore, wash-off examination revealed that the mucoadhesive ability of this delivery system has a long duration and may release the active material at the right time. CONCLUSION: The result of the researches suggesting that the formulation of mucoadhesive microspheres of fluconazole could be used to treat cryptococcal meningitis infection in HIV/AIDS patients.

Detection and Identification of Various Microplastics in Different Orthodontic Adhesives.

Background Microplastics are acknowledged as significant environmental contaminants. The clinical use of dental materials, particularly adhesives containing plastic polymers, can give rise to the production of plastic micro- and nanoparticles, which subsequently find their way into the environment. The aim of the study was to detect different microplastics and identify them in various orthodontic adhesives. Materials and methods Four different light cure orthodontic adhesives, including Transbond XT (3M Unitek, Monrovia, CA), Ormco Enlight (Ormco, Orange, CA), Orthofix SPA (Orthofix, Verona, Italy), and Aqualine LC (Tomy International Inc, Tokyo, Japan), were collected and placed in separate Eppendorf tubes. Microplastics present in each adhesive were identified using scanning electron microscopy. Subsequently, each specimen was suspended in hydrogen peroxide, placed within a shaking incubator, and analyzed using Fourier transform infrared spectroscopy (FTIR) to identify the type of polymer. Results The scanning electron microscope shows the surface morphology and the most predominant types of microplastics identified were fibers, fragments, and pellets. FTIR results showed the presence of several major functional groups, including hydroxyl, amine, ester, fluoro, and halo groups. Conclusion When contrasted with the quantity of microplastic waste generated by other sectors like the textile, cosmetic, and fishing industries, the microparticulate waste stemming from dental adhesives has a minimal effect on environmental deterioration. Strategies for addressing this concern should give precedence to reducing the use of these materials and adopting effective recovery methods, which could potentially involve recycling processes.

The efficacy of Er,Cr:YSGG laser and contemporary universal adhesive systems on composite resin repair bond strength: an in vitro study.

The aim of this study is to investigate the repair bond strength of composite resin following three different surface treatments (bur-grinding, silanization, and Er,Cr:YSGG laser irradiation) using various universal adhesives. A total of 160 resin composite specimens, produced in cylindrical form (6 × 2 mm) with a nanohybrid composite resin within metal molds, were subjected to 5000 cycles of aging in a thermocycler. The aged samples were categorized into four groups based on surface treatments: control, bur, silane, and Er,Cr:YSGG laser. Following surface treatments, the specimens underwent repair using the same resin composite and four different adhesive systems: Tokuyama Universal Bond (TUB), Prime Bond Universal (PBU), Gluma Bond Universal (GBU), and Clearfil SE Bond (CSB). Subsequently, the specimens were subjected to shear forces, and statistical analysis was performed using two-way ANOVA and Tukey tests (p < 0.05). The failure modes were examined using a stereomicroscope, and the surface topography of the roughened resin composite was assessed through scanning electron microscopy (SEM). Results indicated that silane + GBU exhibited the highest shear bond strength (SBS) (15.61 MPa) while control + TUB showed the lowest SBS (7.63 MPa). Silane demonstrated significantly higher SBS values (p ≤ 0.05), with no significant difference observed between bur and laser methods (p = 0.998). It is recommended to include an additional silanization step before applying universal adhesive, as it effectively enhances the bond strength of the repaired composite.

Utilization of Plant Oils for Sustainable Polyurethane Adhesives: A Review.

The utilization of plant oils as a renewable resource for the production of polyurethane adhesives presents a promising way to improve sustainability and reduce environmental impact. This review explores the potential of various vegetable oils, including waste oils, in the synthesis of polyurethanes as an alternative to conventional petroleum-based raw materials. The investigation highlights the environmental challenges associated with conventional polyurethane production and highlights the benefits of switching to bio-renewable oils. By examining the feasibility and potential applications of vegetable oil-based polyurethanes, this study emphasizes the importance of further research and development in this area to realize the full potential of sustainable polyurethane adhesives. Further research and development in this area are key to overcoming the challenges and realizing the full potential of plant-oil-based polyurethanes in various industrial applications.

A Biodegradable Tissue Adhesive for Post-Extraction Alveolar Bone Regeneration under Ongoing Anticoagulation-A Microstructural Volumetric Analysis in a Rodent Model.

In addition to post-extraction bleeding, pronounced alveolar bone resorption is a very common complication after tooth extraction in patients undergoing anticoagulation therapy. The novel, biodegenerative, polyurethane adhesive VIVO has shown a positive effect on soft tissue regeneration and hemostasis. However, the regenerative potential of VIVO in terms of bone regeneration has not yet been explored. The present rodent study compared the post-extraction bone healing of a collagen sponge (COSP) and VIVO in the context of ongoing anticoagulation therapy. According to a split-mouth design, a total of 178 extraction sockets were generated under rivaroxaban treatment, of which 89 extraction sockets were treated with VIVO and 89 with COSP. Post-extraction bone analysis was conducted via in vivo micro-computed tomography (µCT), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX) after 5, 10, and 90 days. During the observation time of 90 days, µCT analysis revealed that VIVO and COSP led to significant increases in both bone volume and bone density (p ≤ 0.001). SEM images of the extraction sockets treated with either VIVO or COSP showed bone regeneration in the form of lamellar bone mass. Ratios of Ca/C and Ca/P observed via EDX indicated newly formed bone matrixes in both treatments after 90 days. There were no statistical differences between treatment with VIVO or COSP. The hemostatic agents VIVO and COSP were both able to prevent pronounced bone loss, and both demonstrated a strong positive influence on the bone regeneration of the alveolar ridge post-extraction.

Evaluation of Microbiological Susceptibility and Long-term Adhesive Properties to Dentin of Primers with Terminalia catappa Linn.

PURPOSE: To investigate the antibacterial effects of Terminalia catappa Linn (TCL) leaf extracts at different concentrations and the effects of these extracts used as primers on the long-term adhesive properties of two universal adhesives. MATERIALS AND METHODS: After extract preparation, the antimicrobial and antibacterial activities of TCL against Streptococcus mutans (UA 159) were assessed in microdilution assays to provide the minimal inhibitory concentration (MIC) and minimal bactericidal concentration (MBC). Additionally, to provide quantitative data on the ability of TCL extract to reduce cell viability, colony forming units (CFU) were counted. To examine adhesive properties, 288 human molars were randomly assigned to 32 experimental conditions (n = 9) according to the following variables: (1) treatment agent: negative control (untreated surface), and primers at concentrations of 1xMIC, 5xMIC, and 10xMIC; (2) adhesives: Scotchbond Universal (SBU) and Futurabond Universal (FBU); (3) adhesive strategy: etch-and-rinse (ER) or self-etch (SE); and (4) storage time: 24 h or after 2 years. Primers were applied for 60 s, upon which the teeth were incrementally restored and sectioned into adhesive-dentin bonded sticks. These were tested for microtensile bond strength (µTBS) and nanoleakage (NL) after 24-h and 2-year water storage, as well as in-situ degree of conversion (DC) at 24 h. The chemical profile of the hybrid layer was determined via micro-Raman spectroscopy. Biofilm assay data were analyzed using the Kruskal-Wallis test; the pH of culture media and the chemical profile were analyzed by one-way ANOVA. The adhesive properties (µTBS, NL, DC) were evaluated using a four-way ANOVA and Tukey's test. Significance was set at 5%. RESULTS: Similar values of MIC and MBC were observed (2 mg/ml), showing bactericidal potential. CFU analysis demonstrated that concentrations of 5xMIC and 10xMIC significantly inhibited biofilm formation (p < 0.001). The application of the TCL primer at all concentrations significantly increased the immediate µTBS and DC, and decreased the immediate NL values when compared to the control group (p < 0.05), regardless of the adhesive and adhesive strategies. Despite an increase in the NL values for all groups after 2 years (p > 0.05), in groups where the TCL primer was applied, the µTBS remained constant after 2 years for both adhesives, while a decrease in the µTBS was observed in the control groups (p < 0.05). Usually, 10xMIC showed better results than 1xMIC and 5xMIC (p < 0.05). The application of TCL promoted cross-linking; cross-linking rates increased proportionally to the concentration of TCL (p < 0.05). CONCLUSION: Primers containing TCL promoted bactericidal and bacteriostatic action, as well as cross-linking with dentin, while maintaining the adhesive properties of the adhesive-dentin interface after 2 years of water storage.

Influence of Talc on the Properties of Silicone Pressure-Sensitive Adhesives.

The article describes new silicone self-adhesive adhesives modified with the addition of talc. The obtained self-adhesive materials were characterized to determine their adhesive properties (adhesion, cohesion, and adhesion) and functional properties (pot life of the composition, shrinkage, and thermal properties of adhesives). Novel materials exhibited high thermal resistance above 225 °C while maintaining or slightly reducing other values (adhesion, cohesion, shrinkage, and tack). Selected composition: T 0.1 was used to prepare self-adhesives in industrial-scale production. Moreover, conducted test results revealed that the addition of talc delayed the thermal decomposition of the adhesive and provided reduced intensity of smoke emissions during combustion as well as the flammability of the adhesive layer.