Tubular Aggregates as a Marker of Aging in Skeletal Muscle.

Tubular aggregates (TA) are skeletal muscle structures that arise from the progressive accumulation of sarcoplasmic reticulum proteins, mainly with aging. Muscle regeneration plays a role in TA formation. TA quantification may aid in the evaluation of muscle aging and genetic muscle degeneration. TA form over time, appears in aging in normal murine muscles. TA reduction in injured conditions may be due to the degeneration-regeneration process in muscles, with loss of damaged muscle fibers and formation of new fibers that do not present protein aggregation. These new regenerated fibers do not improve the function capacity of the aged muscle. Here, we present a methodology for labeling and identifying tubular aggregates in muscle fibers and also the standardization of its quantification.

Micronized Shell-Bioaggregates as Mechanical Reinforcement in Organic Coatings.

Shells are primarily composed of calcite and aragonite, making the inclusion of micronized shells as bio-based fillers in organic coatings a potential means to enhance the mechanical properties of the layers. A water-based coating was reinforced with 5 wt.% Acanthocardia tuberculata powder, 5 wt.% Mytilus galloprovincialis powder, and 5 wt.% of an LDPE/ceramic/nanoceramic composite. An improvement in abrasion resistance was achieved using micronized seashells, as demonstrated by the Taber test (evaluating both weight loss and thickness reduction). Additionally, Buchholz hardness improved with powders derived from Mytilus galloprovincialis. No significant differences were observed among the samples in terms of color and gloss after 200 h of UV-B exposure. However, the delamination length from the scratch after 168 h of exposure in a salt spray chamber indicated that the addition of particles to the polymeric matrix resulted in premature degradation, likely due to the formation of preferential paths for water penetration from the scratch. This hypothesis was supported by electrochemical impedance spectroscopy measurements, which revealed a decrease in total impedance at 0.01 Hz shortly after immersion in a 3.5% NaCl solution. In conclusion, the particle size and shape of the micronized shells improved abrasion resistance without altering color and gloss but led to a decrease in the coating's isolation properties.

Patterned PVA Hydrogels with 3D Petri Dish® Micro-Molds of Varying Topography for Spheroid Formation of HeLa Cancer Cells: In Vitro Assessment.

Cell spheroids are an important three-dimensional (3D) model for in vitro testing and are gaining interest for their use in clinical applications. More natural 3D cell culture environments that support cell-cell interactions have been created for cancer drug discovery and therapy applications, such as the scaffold-free 3D Petri Dish® technology. This technology uses reusable and autoclavable silicone micro-molds with different topographies, and it conventionally uses gelled agarose for hydrogel formation to preserve the topography of the selected micro-mold. The present study investigated the feasibility of using a patterned Poly(vinyl alcohol) hydrogel using the circular topography 12-81 (9 × 9 wells) micro-mold to form HeLa cancer cell spheroids and compare them with the formed spheroids using agarose hydrogels. PVA hydrogels showed a slightly softer, springier, and stickier texture than agarose hydrogels. After preparation, Fourier transform infrared (FTIR) spectra showed chemical interactions through hydrogen bonding in the PVA and agarose hydrogels. Both types of hydrogels favor the formation of large HeLa spheroids with an average diameter of around 700-800 µm after 72 h. However, the PVA spheroids are more compact than those from agarose, suggesting a potential influence of micro-mold surface chemistry on cell behavior and spheroid formation. This was additionally confirmed by evaluating the spheroid size, morphology, integrity, as well as E-cadherin and Ki67 expression. The results suggest that PVA promotes stronger cell-to-cell interactions in the spheroids. Even the integrity of PVA spheroids was maintained after exposure to the drug cisplatin. In conclusion, the patterned PVA hydrogels were successfully prepared using the 3D Petri Dish® micro-molds, and they could be used as suitable platforms for studying cell-cell interactions in cancer drug therapy.

Cyanobacterial biocrust alters soil physical properties reducing soil erosion and aerosol production.

Aerosol emission by wind erosion in the arid and semi-arid areas of the world, is of environmental and health significance. Different methods have been used to mitigate aerosol emission among which the biological methods may be the most efficient ones. Although previously investigated, more research is essential to determine how the use of exopolysaccharide (biocrust)-producing cyanobacteria may affect soil physical properties. The objective was to investigate the effects of the cyanobacteria, Microcoleus vaginatus ATHK43 (identified and registered by the NCBI accession number MW433686), on soil physical properties of a sandy soil 15, 30, 60, and 90 d after inoculation. The effects of cyanobacterial biocrust on soil properties including shear strength, soil resistance, aggregate stability (mean weight diameter (MWD) and geometric mean diameter (GMD)), and wind erosion were determined in trays using a wind tunnel. Cyanobacterial inoculation significantly increased MWD (0-1 cm depth, from 0.12 mm to 0.47 mm) and GMD (from 0.3 to 0.5 mm) after a period of 90 d. Biocrust production significantly decreased soil erosion from 55.7 kgm- 2 to 0.3 kgm- 2 (wind rate of 50 kmh- 1), and from 116.42 kgm- 2 to 0.6 kgm- 2 (wind rate of 90 kmh- 1) after 90 d. In conclusion, cyanobacterial biocrust can significantly improve soil physical properties in different parts of the world including the deserts, and reduce aerosol emission by mitigating the destructive effects of wind erosion on soil physical properties.

Induced degeneration and regeneration in aged muscle reduce tubular aggregates but not muscle function.

Introduction: Tubular aggregates (TA) are skeletal muscle structures that arise from the progressive accumulation of sarcoplasmic reticulum proteins. Cytoplasmic aggregates in muscle fibers have already been observed in mice and humans, mainly during aging and muscle disease processes. However, the effects of muscle regeneration on TA formation have not yet been reported. This study aimed to investigate the relationship between degeneration/regeneration and TA in aged murine models. We investigated the presence and quantity of TA in old males from two murine models with intense muscle degeneration and regeneration. Methods: One murine lineage was a Dmdmdx model of Duchenne muscular dystrophy (n = 6). In the other model, muscle damage was induced by electroporation in C57BL/6J wild-type mice, and analyzed after 5, 15, and 30 days post-electroporation (dpe; n = 15). Regeneration was evaluated based on the quantity of developmental myosin heavy chain (dMyHC)-positive fibers. Results: The frequency of fibers containing TA was higher in aged C57BL/6J (26 ± 8.3%) than in old dystrophic Dmdmdx mice (2.4 ± 2%). Comparing the data from induced degeneration/regeneration in normal mice revealed a reduced proportion of TA-containing fibers after 5 and 30 dpe. Normal aged muscle was able to regenerate and form dMyHC+ fibers, mainly at 5 dpe (0.1 ± 0.1 vs. 16.5 ± 2.6%). However, there was no difference in force or resistance between normal and 30 dpe animals, except for the measurements by the Actimeter device, which showed the worst parameters in the second group. Discussion: Our results suggest that TA also forms in the Dmdmdx muscle but in smaller amounts. The intense degeneration and regeneration of the old dystrophic model resulted in the generation of new muscle fibers with a lower quantity of TA. Data from electroporated wild-type mice support the idea that muscle regeneration leads to a reduction in the amount of TA. We suggest that TA accumulates in muscle fibers throughout physiological aging and that regeneration leads to the formation of new fibers without these structures. In addition, these new fibers do not confer functional benefits to the muscle.

Total absorption spectrum of benzene aggregates obtained from two different approaches.

CONTEXT: The study of molecular aggregation effects on the electronic spectrum is essential for the development of optoelectronic devices. However, investigating the entire valence absorption spectrum of aggregates using quantum mechanical methods is a challenging task. In this work, we perform systematic simulations of the absorption spectrum of benzene molecular clusters up to 35 eV applying two approaches based on time-dependent density functional theory. The results show that depending on the dimer packing, different energy shifts occur for the symmetry allowed [Formula: see text] transition, in comparison to the monomer. The transition intensity increases for the band around 6 eV for larger aggregates from the monomer to dimers and tetramer, indicating the occurrence of the symmetry forbidden (in [Formula: see text] point group) [Formula: see text] [Formula: see text] transition. The benzene crystal exhibits a large redshift following the experimental spectrum. Also, the continuum regions of all spectra show a good agreement with the experiments both in gas and solid phases. METHODS: Geometry optimization of the monomer was carried out with Gaussian 09 software using the PBE0/def2-TZVP level of theory. We used dimers and tetramer molecular geometries extracted from the experimental crystal structure. The absorption spectra were directly obtained by the Liouville-Lanczos TDDFT approach with plane waves basis set or indirectly by TDDFT pseudo-spectra calculated in a [Formula: see text] basis followed by analytic continuation procedure to obtain complex polarizability. The former is available at Quantum ESPRESSO, and the latter was calculated using Gaussian 09 with the post-processing performed with a code previously developed in our group.

Long chain capsaicin analogues synthetized by CALB-CLEAs show cytotoxicity on glioblastoma cell lines.

Glioblastoma is one of the most lethal tumors, displaying striking cellular heterogeneity and drug resistance. The prognosis of patients suffering from glioblastoma after 5 years is only 5%. In the present work, capsaicin analogues bearing modifications on the acyl chain with long-chain fatty acids showed promising anti-tumoral activity by its cytotoxicity on U-87 and U-138 glioblastoma multiforme cells. The capsaicin analogues were enzymatically synthetized with cross-linked enzyme aggregates of lipase B from Candida antarctica (CALB). The catalytic performance of recombinant CALB-CLEAs was compared to their immobilized form on a hydrophobic support. After 72 h of reaction, the synthesis of capsaicin analogues from linoleic acid, docosahexaenoic acid, and punicic acid achieved a maximum conversion of 69.7, 8.3 and 30.3% with CALB-CLEAs, respectively. Similar values were obtained with commercial CALB, with conversion yields of 58.3, 24.2 and 22% for capsaicin analogues from linoleic acid, DHA and punicic acid, respectively. Olvanil and dohevanil had a significant cytotoxic effect on both U-87 and U-138 glioblastoma cells. Irrespective of the immobilization form, CALB is an efficient biocatalyst for the synthesis of anti-tumoral capsaicin derivatives. KEY POINTS: • This is the first report concerning the enzymatic synthesis of capsaicin analogues from docosahexaenoic acid and punicic acid with CALB-CLEAs. • The viability U-87 and U-138 glioblastoma cells was significantly affected after incubation with olvanil and dohevanil. • Capsaicin analogues from fatty acids obtained by CALB-CLEAs are promising candidates for therapeutic use as cytotoxic agents in glioblastoma cancer cells.

Increasing the aqueous solubility of the anesthetic propofol through wormlike micelle formation.

Propofol, a phenol derivative, is commonly employed as an intravenous anesthetic during clinical procedures, formulated as an oil/water emulsion due to its poor solubility in water. The stability limitations associated with emulsions have prompted research efforts towards developing aqueous formulations of propofol. In this work, we investigate the solubility enhancement of propofol in anionic and cationic surfactants. Our findings reveal that the solubility of propofol can increase significantly, up to 100-fold, depending on the nature of the micellar aggregate, as observed for alkylammonium halogenates CnTAB (for n = 12, 14 and 16), contrasting with the lower solubility with SDS. Interestingly, C14TAB and C16TAB demonstrate significantly higher solubility than C12TAB. This was attributed to the formation of wormlike micelles, in which the propofol molecules are positioned between the cationic heads of the surfactant molecules, changing the micellar curvature and the morphology of the aggregate. Therefore, the aromatic molecules in the micellar environment can be partitioned into the micellar cores and their palisades. Regarding C12TAB, the alkyl chain is too short to form wormlike micelles, thus, concentrating propofol molecules mainly into the micellar core, and consequently, leading to their aggregation. Solubility diagrams of propofol were constructed in conjunction with different surfactants. The systems exhibiting viscoelastic behavior, indicative of wormlike micelle formation, were further investigated using rheology. Additionally, the fluorescent properties of propofol enabled the examination of the anesthetic molecule within diverse micellar environments.

Shedding Light on Highly Emissive 1,4-Dihydropyrrolo[3,2-b]pyrrole Derivatives: Synthesis and Aggregate-Dependent Emission.

Three tetraaryl-1,4-dihydropyrrolo[3,2-b]pyrrole derivatives containing different number of long alkoxy chains (2, 4 and 6) were synthesized, characterized and applied in Organic Light Emitting Diodes (OLEDs). The compounds showed good emission properties with Photoluminescence Quantum Yields (PLQYs) higher than 80 % in solution and 50 % in solid state (thin film). The solvatochromism results revealed a pronounced vibronic emission in methylcyclohexane and toluene, characterized by two distinct sharp emission peaks and a small redshift in the following order: methylcyclohexane>toluene>dichloromethane>tetrahydrofuran>acetonitrile. Also, the compounds formed aggregates with redshifted emission, which can be attributed to excimer formation. This phenomenon was observed in solutions containing 90 % water and with the concentration variation in methylcyclohexane (MCH). Compounds with a greater number of peripheral chains showed the capacity to keep hexagonal columnar organization in films after fast cooling from liquid state. OLEDs fabricated with these compounds showed turn-on voltages lower than 4.0 V, with luminance higher than 1400 cd m-2 , electroluminescence spectra with Full Width at Half Maximum lower than 70 nm and maximum External Quantum Efficiency between 7.2 % and 4.3 %. Overall, this shows that the 1,4-dihydropyrrolo[3,2-b]pyrrole moiety is promising for applications where luminescence is paramount, as in organic light-emitting devices.

Assessment of Wood Bio-Concrete Properties Modified with Silane-Siloxane.

Bio-based materials, such as wood bio-concrete (WBC), hold promise in reducing energy consumption and carbon footprint of the construction industry. However, the durability of these materials is not well understood and can be negatively affected by the high water absorption capacity of wood bio-aggregates. In the field of cement composites, for example, silane-siloxane-based water repellent has been used to protect such materials from natural environmental attack. Nevertheless, there is still a limited understanding of various aspects related to this type of treatment, including its performance when applied to the bio-concrete substrate. This research aimed to investigate the influence of silane-siloxane on the rheology and hydration of cementitious paste through isothermal calorimetry and thermogravimetric analysis. Additionally, the impact of silane-siloxane on the physical and mechanical properties of WBCs was examined by conducting tests at fresh state (flow table and entrained air content) and hardened state (compressive strength and capillary water absorption). The composites were produced with a volumetric fraction of 45% of wood shavings while the cement matrix consisted of a combination of cement, rice husk ash, and fly ash. Silane-siloxane was applied in three ways: as coating, incorporated as an admixture, and in a combination of both methods. The results indicated that by incorporating silane in the cementitious pastethe viscosity increased by 40% and the hydration was delayed by approximately 6 h when compared to the reference. In addition, silane improved the compressive strength of WBCs by 24% when incorporated into the mixture, expressively reduced the water sorptivity of WBCs (93%), and was more effective if used as coating.

Hybrid Cements and Construction Elements Based on Alkaline Activation with Sodium Sulfates from Fly Ash and Construction and Demolition Waste.

This article demonstrates the possibility of producing hybrid cementitious materials (pastes, mortars, concretes, and precast elements) based on fly ash (FA) and construction and demolition wastes (CDW) using alkaline activation technology. Sodium sulfate was used as an activator and fine and coarse aggregates were obtained from CDW residues. An addition of Portland cement (OPC) (10 to 30%) allowed for improvement in the mechanical behavior of the hybrid cements and them to be cured at room temperature (25 °C). The FA and CDW cementitious materials obtained compressive strengths of 37 MPa and 32 MPa, respectively. The compressive strength of FA and CDW alkali-activated concretes at 28 days of curing was 22 MPa and 18 MPa, respectively, which identifies them as structural concretes according to NSR-10 title C in Colombia. The potential use of these concretes was validated by obtaining and classifying precast materials.

Metal ion content of internal organs in the calorically restricted Wistar rat.

BACKGROUND: Despite the agreed principle that access to food is a human right, undernourishment and metal ion deficiencies are public health problems worldwide, exacerbated in impoverished or war-affected areas. It is known that maternal malnutrition causes growth retardation and affects behavioral and cognitive development of the newborn. Here we ask whether severe caloric restriction leads per se to disrupted metal accumulation in different organs of the Wistar rat. METHODS: Inductively coupled plasma optical emission spectroscopy was used to determine the concentration of multiple elements in the small and large intestine, heart, lung, liver, kidney, pancreas, spleen, brain, spinal cord, and three skeletal muscles from control and calorically restricted Wistar rats. The caloric restriction protocol was initiated from the mothers prior to mating and continued throughout gestation, lactation, and post-weaning up to sixty days of age. RESULTS: Both sexes were analyzed but dimorphism was rare. The pancreas was the most affected organ presenting a higher concentration of all the elements analyzed. Copper concentration decreased in the kidney and increased in the liver. Each skeletal muscle responded to the treatment differentially: Extensor Digitorum Longus accumulated calcium and manganese, gastrocnemius decreased copper and manganese, whereas soleus decreased iron concentrations. Differences were also observed in the concentration of elements between organs independently of treatment: The soleus muscle presents a higher concentration of Zn compared to the other muscles and the rest of the organs. Notably, the spinal cord showed large accumulations of calcium and half the concentration of zinc compared to brain. X-ray fluorescence imaging suggests that the extra calcium is attributable to the presence of ossifications whereas the latter finding is attributable to the low abundance of zinc synapses in the spinal cord. CONCLUSION: Severe caloric restriction did not lead to systemic metal deficiencies but caused instead specific metal responses in few organs.

Copper-induced aggregation of IgG: a potential driving force for the formation of circulating protein aggregates.

Copper is a highly reactive element involved in a myriad of biological reactions. Thus, while essential for mammalian cells, its concentrations must be kept in check in order to avoid toxicity. This metal participates in redox reactions and may exacerbate oxidative stress in aerobic organisms. Nonetheless, the actual driving force of copper-induced cell death is yet unknown. Likely, free copper ions may target different biomolecules that are crucial for the proper functioning of an organism. In this work, we show that free copper induces protein aggregation in serum. The wide set of proteins present in these biological samples are not equally prone to copper-induced aggregation and some, such as albumin, are highly resistant, whereas γ-globulins are highly sensitive. The identity of the proteins in the aggregates becomes fairly homogeneous as metal concentrations go as low as 20 µM. The identification of the proteins by mass spectrometry indicates a preponderance of IgG and a minor presence of other different proteins. Therefore, free copper in blood may contribute to the formation of circulating protein aggregates with a core of IgG. This may impact health not only due to the activity of aggregated IgG but also due to the many proteins co-aggregated. Understanding whether the γ-globulin core and the heterogeneous subgroup of proteins elicit differential responses in the organisms requires further research.

Sorghum bicolor SbHSP110 has an elongated shape and is able of protecting against aggregation and replacing human HSPH1/HSP110 in refolding and disaggregation assays.

Perturbations in the native structure, often caused by stressing cellular conditions, not only impair protein function but also lead to the formation of aggregates, which can accumulate in the cell leading to harmful effects. Some organisms, such as plants, express the molecular chaperone HSP100 (homologous to HSP104 from yeast), which has the remarkable capacity to disaggregate and reactivate proteins. Recently, studies with animal cells, which lack a canonical HSP100, have identified the involvement of a distinct system composed of HSP70/HSP40 that needs the assistance of HSP110 to efficiently perform protein breakdown. As sessile plants experience stressful conditions more severe than those experienced by animals, we asked whether a plant HSP110 could also play a role in collaborating with HSP70/HSP40 in a system that increases the efficiency of disaggregation. Thus, the gene for a putative HSP110 from the cereal Sorghum bicolor was cloned and the protein, named SbHSP110, purified. For comparison purposes, human HsHSP110 (HSPH1/HSP105) was also purified and investigated in parallel. First, a combination of spectroscopic and hydrodynamic techniques was used for the characterization of the conformation and stability of recombinant SbHSP110, which was produced folded. Second, small-angle X-ray scattering and combined predictors of protein structure indicated that SbHSP110 and HsHSP110 have similar conformations. Then, the chaperone activities, which included protection against aggregation, refolding, and reactivation, were investigated, showing that SbHSP110 and HsHSP110 have similar functional activities. Altogether, the results add to the structure/function relationship study of HSP110s and support the hypothesis that plants have multiple strategies to act upon the reactivation of protein aggregates.

Carbonation Behavior of Mortar Made from Treated Recycled Aggregates: Influence of Diammonium Phosphate.

This research aims to improve the quality of recycled concrete fine aggregates (RFA) by using diammonium hydrogen phosphate (DAP). We aimed to understand the effect of DAP treatment on durability performance due to the carbonation action of mortars with the partial and total substitution of treated RFA. The results showed a maximum reduction in the RFA water absorption of up to 33% using a minimum DAP concentration due to a pore refinement as a consequence of the formation of calcium phosphates such as hydroxyapatite (HAP). The carbonation phenomenon did not have a significant effect on the durability of mortars with DAP-treated RFA, as we did not find a decrease in the compressive strength; the carbonation depth of the mortars with 100% treated RFA decreased up to 90% and 63% for a w/c of 0.45 and 0.50, in comparison with mortars with 0% treated RFA. An inversely proportional relationship was found between the accelerate carbonation and the compressive strength, showing that higher percentages of treated RFAs in the mortar promoted an increase in compressive strength and a decrease in the carbonation rate, which is behavior associated with a lower permeability of the cement matrix as one of the consequences of the microstructural densification by DAP treatment.

Using High Pressure and Alkaline pH for Refolding.

The expression of recombinant proteins as insoluble inclusion bodies (IB) has the advantage to separate insoluble aggregates from soluble bacterial molecules, thus obtaining proteins with a high degree of purity. Even aggregated, the proteins in IB often present native-like secondary and tertiary structures, which can be maintained as long as solubilization is carried out in non-denaturing condition. High pressure solubilizes IB by weakening hydrophobic interactions, while alkaline pH solubilizes aggregates by electrostatic repulsion. The combination of high pressure and alkaline pH is effective for IB solubilization at a mild, non-denaturing condition, which is useful for subsequent refolding. Here, we describe the expression of recombinant proteins in Escherichia coli using a rich medium to obtain high expression levels, bacterial lysis, and washing of the IB to obtain products of high purity, and, finally, the solubilization and high yield of refolded proteins using high pressure and alkaline pH.

Strategy for the formation of microalgae-bacteria aggregates in high-rate algal ponds.

This work studied the formation of aggregates used for wastewater treatment in high-rate algal ponds (HRAP). For this, the establishment of microalgae-bacteria aggregates in these systems was evaluated, considering strategies for the inoculation and start-up. Two HRAP were operated in parallel, at first in batch mode and then in continuous flow. The wastewater treatment was efficient, with removal rates around 80% for COD and N-ammoniacal. Volatile suspended solids and chlorophyll for the culture grew continuously reached a concentration of 548 ± 11 mg L-1 and 7.8 mg L-1, respectively. Larger photogranules were observed when the system was placed in a continuous regime. The protein fraction of extracellular polymeric substances was identified as a determinant in photogranules formation. During the continuous regime, more than 50% of the biomass was higher than 0.2 mm, flocculation efficiency of 78 ± 6%, and the volumetric sludge index of 32 ± 5 mL g-1. The genetic sequencing showed the growth of cyanobacteria in the aggregate and the presence of microalgae from the chlorophytes and diatoms groups in the final biomass.

Photocatalytic Activity and Self-Cleaning Effect of Coating Mortars with TiO2 Added: Practical Cases in Warm Sub-Humid Climates.

In this study, the photocatalytic activity of coating mortars with synthetized and commercial TiO2 nanoparticles added has been evaluated at 2, 3 and 5% by weight of cement by calculating the degradation efficiency of methyl orange and red wine dyes exposed to both visible-light and UV radiation; also, the self-cleaning effect of coatings exposed to weather conditions (warm sub-humid climate) was assessed. TiO2 nanoparticles were synthesized via the sol-gel method to a low synthesis temperature and characterized via X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM). The results show synthesized TiO2 particles in anatase phase with a crystallite size of 14.69 nm, and hemispherical particles with sizes of submicron order. The addition percentage with the best performance in the coating mortars was 3%, with both commercial and synthesized TiO2; however, coating mortars with synthesized TiO2 exhibited the highest degradation efficiency for both dyes when they were exposed to visible light, while mortars with commercial TiO2 exhibited the highest degradation efficiency when exposed to UV radiation. In addition, in coating mortars with synthesized TiO2, the self-cleaning effect was evident from the beginning of exposure to weather, reaching the largest dye-free surface at the end of exposure. The compressive strength increased significantly in mortars with TiO2 addition.

Soil aggregation and associated organic matter under management systems in sandy-textured soils, subtropical region of Brazil.

Increasing the diversity of plant species in agricultural production areas favors the maintenance or improvement of soil quality, particularly for soils with a sandy texture. This beneficial effect is related to the formation of aggregates of different origins. This study aimed to (i) verify whether soil use and management affect the proportion of biogenic (Bio) and physicogenic (Phy) aggregates and (ii) verify whether biogenic aggregation is more likely to lead to soil improvement than physicogenic aggregation. Three management systems were evaluated (permanent pasture, PP; no-tillage system, NT; and no-tillage + Brachiaria system, NT + B) as well as a reference area (Atlantic Forest biome vegetation, NF). According to their origin or formation pathway, the aggregates were separated, identified, and classified as Bio (formed by biological processes) and Phy (resulting from chemical and physical actions). The differentiation between Bio and Phy aggregates was performed based on the visualization of morphological features, such as shape, size, presence of roots, porosity, and subunit arrangements, and junctions. Only the PP area was able to promote greater aggregate formation of biological origin, with greater amounts of Bio aggregates. The highest total organic carbon (TOC) contents and the least negative δ13C values were also quantified in the aggregates of the PP area. The NT + B system provided an increase in the TOC content of its aggregates in comparison with aggregates in the NT and NF areas. Among the formation pathways, the Bio aggregates had the highest TOC and soil organic matter fractions contents and the most negative δ13C values. Perennial forage grasses vegetation was more important than the plant species diversity in favoring Bio aggregate formation. The beneficial effect of Brachiaria can be observed when incorporated as part of intercropping with corn in grain production systems. The biogenic aggregates favored the concentration of more labile soil organic matter fractions. The results of this study can provide important theoretical information for future studies focused on the combination of different plant species in agricultural food production areas on sandy-textured soils.

Recycled Fine Aggregates from Mortar Debris and Red Clay Brick to Fabricate Masonry Mortars: Mechanical Analysis.

In this research, the mechanical behavior of masonry mortars made with partial substitution of sand by recycled fine aggregates (RFAs) of mortar (MT) and recycled clay brick (RCB) was compared. Mortar specimens were built in two groups (MT and RCB) considering different replacement proportions by dry weight. To reduce the water absorption of RFAs during mortar making, the prewetting method was utilized. All the mixtures were assembled with a volumetric cement-to-aggregate ratio of 1:4 and a consistency of 175 ± 5 mm. The properties in the fresh and hardening state of mortars were analyzed separately. The experimental results showed that the properties of mortars in a fresh state (bulk density and air content) were affected if RFA was added to the mixture; however, mortars assembled with up to 40% and 50% of MT and RCB, respectively, accomplished a compressive strength value of reference for new mixtures. Both mortar groups showed good results in adhesive strength values, with the RCB mortars standing up as they achieved greater adherence than the control mortar with substitution percentages of up to 30%. Therefore, the reutilization of both RFAs is feasible, notably in rendering and bonding functions.