Reinforced Magnetic-Responsive Electro-Ionic Artificial Muscles by 3D Laser-Induced Graphene Nano-Heterostructures.

Efficient ion transport and enriched responsive modals via modulating electrochemical properties of conductivity and capacitance are essential for soft electro-ionic actuators. However, cost-effective and straightforward approaches to achieve expedited fabrication of active electrode materials capable of multimodal-responsiveness remain limited. Herein, this work reports the one-step ultrafast laser direct patterning method, to readily synthesize electro- and magneto-active electrode material, derived from the unique cobalt-phosphorus co-doped core-shell heterostructures within 3D graphene frameworks, for fulfilling the dual-mode responsive electro-ionic actuators. The designed nanofiber-structured heterointerfaces across electrodes and electrolytes further promote highly efficient electron/ion transfer. The developed soft actuator exhibits superior actuation performance of peak-to-peak displacement to 13.08 mm under an ultra-low ±0.5 V, with doubled direct current deflection under 200 mT at 1 V, an ultrafast response of 1.38 s and long-term stability (>90% retention for ≈106 000 cycles), even detectable bending to ≈280 µm under exceptional ±10 mV. The promising demonstration of promoting differentiation and proliferation of stem cells under mechanical strain and electrical stimuli, sheds more light as well on the possibility of facilitating biomedical soft robotics with ultrahigh actuation performance.

Fast, variable stiffness-induced braided coiled artificial muscles.

Biomimetic actuation technologies with high muscle strokes, cycle rates, and work capacities are necessary for robotic systems. We present a muscle type that operates based on changes in muscle stiffness caused by volume expansion. This muscle is created by coiling a mechanically strong braid, in which an elastomer hollow tube is adhesively attached inside. We show that the muscle reversibly contracts by 47.3% when driven by an oscillating input air pressure of 120 kilopascals at 10 Hz. It generates a maximum power density of 3.0 W/g and demonstrates a mechanical contractile efficiency of 74%. The muscle's low-pressure operation allowed for portable, thermal pneumatical actuation. Moreover, the muscle demonstrated bipolar actuation, wherein internal pressure leads to muscle length expansion if the initial muscle length is compressed and contraction if the muscle is not compressed. Modeling indicates that muscle expansion significantly alters its stiffness, which causes muscle actuation. We demonstrate the utility of BCMs for fast running and climbing robots.

Carbon Nanotube-Doped 3D-Printed Silicone Electrode for Manufacturing Multilayer Porous Plasticized Polyvinyl Chloride Gel Artificial Muscles.

Plasticized polyvinyl chloride (PVC) gel has large deformation under an applied external electrical field and high driving stability in air and is a candidate artificial muscle material for manufacturing a flexible actuator. A porous PVC gel actuator consists of a mesh positive pole, a planar negative pole, and a PVC gel core layer. The current casting method is only suitable for manufacturing simple 2D structures, and it is difficult to produce multilayer porous structures. This study investigated the feasibility of a 3D-printed carbon nanotube-doped silicone electrode for manufacturing multilayer porous PVC gel artificial muscle. Carbon nanotube-doped silicone (CNT-PDMS) composite inks were developed for printing electrode layers of PVC gel artificial muscles. The parameters for the printing plane and mesh electrodes were explored theoretically and experimentally. We produced a CNT-PDMS electrode and PVC gel via integrated printing to manufacture multilayer porous PVC artificial muscle and verified its good performance.

Silver Coated Multifunctional Liquid Crystalline Elastomer Polymeric Composites as Electro-Responsive and Piezo-Resistive Artificial Muscles.

Liquid crystalline elastomers (LCEs) are a class of shape-changing polymers with exceptional mechanical properties and potential as artificial muscles/polymer actuators. In this study, multifunctional LCE actuators with strain sensing and joule heating responsivity are developed. LCEs are successfully synthesized using the thiol-ene two-staged michael addition polymerization (TMAP) method. The LCE films are further functionalized via sequential polydopamine (PDA) and silver electroless coating. It is found that the PDA coating enabled the anchoring of the Ag particles to the LCE, thereby enabling the electrical conductivity of the Ag-LCEs (<0.1 Ω cm-1). The studies confirm that the Ag/PDA coated LCEs can sense up to ≈30% strain, sense their own actuation strokes, and actuate at a rate of 1.83% s-1 while lifting a weight ≈50 times its mass in response to a 12 V 2A DC current.

DE-AFO: A Robotic Ankle Foot Orthosis for Children with Cerebral Palsy Powered by Dielectric Elastomer Artificial Muscle.

Conventional passive ankle foot orthoses (AFOs) have not seen substantial advances or functional improvements for decades, failing to meet the demands of many stakeholders, especially the pediatric population with neurological disorders. Our objective is to develop the first comfortable and unobtrusive powered AFO for children with cerebral palsy (CP), the DE-AFO. CP is the most diagnosed neuromotor disorder in the pediatric population. The standard of care for ankle control dysfunction associated with CP, however, is an unmechanized, bulky, and uncomfortable L-shaped conventional AFO. These passive orthoses constrain the ankle's motion and often cause muscle disuse atrophy, skin damage, and adverse neural adaptations. While powered orthoses could enhance natural ankle motion, their reliance on bulky, noisy, and rigid actuators like DC motors limits their acceptability. Our innovation, the DE-AFO, emerged from insights gathered during customer discovery interviews with 185 stakeholders within the AFO ecosystem as part of the NSF I-Corps program. The DE-AFO is a biomimetic robot that employs artificial muscles made from an electro-active polymer called dielectric elastomers (DEs) to assist ankle movements in the sagittal planes. It incorporates a gait phase detection controller to synchronize the artificial muscles with natural gait cycles, mimicking the function of natural ankle muscles. This device is the first of its kind to utilize lightweight, compact, soft, and silent artificial muscles that contract longitudinally, addressing traditional actuated AFOs' limitations by enhancing the orthosis's natural feel, comfort, and acceptability. In this paper, we outline our design approach and describe the three main components of the DE-AFO: the artificial muscle technology, the finite state machine (the gait phase detection system), and its mechanical structure. To verify the feasibility of our design, we theoretically calculated if DE-AFO can provide the necessary ankle moment assistance for children with CP-aligning with moments observed in typically developing children. To this end, we calculated the ankle moment deficit in a child with CP when compared with the normative moment of seven typically developing children. Our results demonstrated that the DE-AFO can provide meaningful ankle moment assistance, providing up to 69% and 100% of the required assistive force during the pre-swing phase and swing period of gait, respectively.

Design and Analysis of a Polymeric Left Ventricular Simulator via Computational Modelling.

Preclinical testing of medical devices is an essential step in the product life cycle, whereas testing of cardiovascular implants requires specialised testbeds or numerical simulations using computer software Ansys 2016. Existing test setups used to evaluate physiological scenarios and test cardiac implants such as mock circulatory systems or isolated beating heart platforms are driven by sophisticated hardware which comes at a high cost or raises ethical concerns. On the other hand, computational methods used to simulate blood flow in the cardiovascular system may be simplified or computationally expensive. Therefore, there is a need for low-cost, relatively simple and efficient test beds that can provide realistic conditions to simulate physiological scenarios and evaluate cardiovascular devices. In this study, the concept design of a novel left ventricular simulator made of latex rubber and actuated by pneumatic artificial muscles is presented. The designed left ventricular simulator is geometrically similar to a native left ventricle, whereas the basal diameter and long axis length are within an anatomical range. Finite element simulations evaluating left ventricular twisting and shortening predicted that the designed left ventricular simulator rotates approximately 17 degrees at the apex and the long axis shortens around 11 mm. Experimental results showed that the twist angle is 18 degrees and the left ventricular simulator shortens 5 mm. Twist angles and long axis shortening as in a native left ventricle show it is capable of functioning like a native left ventricle and simulating a variety of scenarios, and therefore has the potential to be used as a test platform.

A Microactuator Array Based on Ionic Electroactive Artificial Muscles for Cell Mechanical Stimulation.

Mechanical stimulation is prevalent within organisms, and appropriate regulation of such stimulation can significantly enhance cellular functions. Consequently, the in vitro construction and simulation of mechanical stimulation have emerged as a research hotspot in biomechanics. In recent years, a class of artificial muscles named electroactive polymers (EAPs), especially ionic EAPs, have shown promising applications in biomechanics. While several techniques utilizing ionic EAPs for cell mechanical stimulation have been reported, further research is needed to advance and enhance their practical applications. Here, we prepared a microactuator array based on ionic EAP artificial muscles for cell mechanical stimulation. As a preliminary effort, we created a 5 × 5 microactuator array on a supporting membrane by employing laser cutting. We evaluated the electro-actuation performance of the microactuators through experimental testing and numerical simulations, affirming the potential use of the microactuator array for cell mechanical stimulation. The devised approach could inspire innovative design concepts in the development of miniaturized intelligent electronic devices, not only in biomechanics and biomimetics but also in other related fields.

Embedding Bifurcations into Pneumatic Artificial Muscle.

Harnessing complex body dynamics has long been a challenge in robotics, particularly when dealing with soft dynamics, which exhibit high complexity in interacting with the environment. Recent studies indicate that these dynamics can be used as a computational resource, exemplified by the McKibben pneumatic artificial muscle, a common soft actuator. This study demonstrates that bifurcations, including periodic and chaotic dynamics, can be embedded into the pneumatic artificial muscle, with the entire bifurcation structure using the framework of physical reservoir computing. These results suggest that dynamics not present in training data can be embedded through bifurcation embedment, implying the capability to incorporate various qualitatively different patterns into pneumatic artificial muscle without the need to design and learn all required patterns explicitly. Thus, this study introduces a novel approach to simplify robotic devices and control training by reducing reliance on external pattern generators and the amount and types of training data needed for control.

Design and Analysis of Reconfigurable Origami-Based Vacuum Pneumatic Artificial Muscles for Versatile Robotic System.

In this study, a vacuum-based modular actuator system named reconfigurable origami-based vacuum pneumatic artificial muscles (ROV-PAMs) is presented. The system consists of six types of actuating modules and three types of fluidic supporting modules each embedded with magnet-based connectors so that the modules can be assembled to modify the system behavior. The module can be used in a myriad of ways, including extending their working range, creating complex geometries upon deformation, and cooperating to improve overall performance. A simple analytical model for the actuating modules is derived based on the law of conservation of energy, and the model is verified experimentally which shows that this intuitive model can provide a reasonable prediction of performance. A block sorting robot is built using three different types of actuating modules with multiple fluidic supporting modules, and the robot shows that it is possible to flexibly and easily assemble modules to build a robot capable of completing diverse tasks. The ROV-PAM module and its concept can be applied to realize robotic designs, which can be altered on-the-fly to adjust its functionality to meet the evolving requirements required for truly flexible automation.

High Performance Proprioceptive Fiber Actuators Based on Ag Nanoparticles-Incorporated Hybrid Twisted and Coiled System.

Thermally driven fiber actuators are emerging as promising tools for a range of robotic applications, encompassing soft and wearable robots, muscle function restoration, assistive systems, and physical augmentation. Yet, to realize their full potential in practical applications, several challenges, such as a high operational temperature, incorporation of intrinsic self-sensing capabilities for closed-loop feedback control, and reliance on bulky, intricate actuation systems, must be addressed. Here, an Ag nanoparticles-based twisted and coiled fiber actuator that achieves a high contractile actuation of ≈36% is reported at a considerably low operational temperature of ≈83 °C based on a synergistic effect of constituent fiber elements with low glass transition temperatures. The fiber actuator can monitor its contractile actuation in real-time based on the piezoresistive properties inherent to its Ag-based conductive region, demonstrating its proprioceptive sensing capability. By exploiting this capability, the proprioceptive fiber actuator adeptly maintains its intended contractile behavior, even when faced with unplanned external disturbances. To demonstrate the capabilities of the fiber actuator, this study integrates it into a closed-loop feedback-controlled bionic arm as an artificial muscle, offering fresh perspectives on the future development of intelligent wearable devices and soft robotic systems.

Knittable Electrochemical Yarn Muscle for Morphing Textiles.

Morphing textiles, crafted using electrochemical artificial muscle yarns, boast features such as adaptive structural flexibility, programmable control, low operating voltage, and minimal thermal effect. However, the progression of these textiles is still impeded by the challenges in the continuous production of these yarn muscles and the necessity for proper structure designs that bypass operation in extensive electrolyte environments. Herein, a meters-long sheath-core structured carbon nanotube (CNT)/nylon composite yarn muscle is continuously prepared. The nylon core not only reduces the consumption of CNTs but also amplifies the surface area for interaction between the CNT yarn and the electrolyte, leading to an enhanced effective actuation volume. When driven electrochemically, the CNT@nylon yarn muscle demonstrates a maximum contractile stroke of 26.4%, a maximum contractile rate of 15.8% s-1, and a maximum power density of 0.37 W g-1, surpassing pure CNT yarn muscles by 1.59, 1.82, and 5.5 times, respectively. By knitting the electrochemical CNT@nylon artificial muscle yarns into a soft fabric that serves as both a soft scaffold and an electrolyte container, we achieved a morphing textile is achieved. This textile can perform programmable multiple motion modes in air such as contraction and sectional bending.

How to Easily Make Self-Sensing Pneumatic Inverse Artificial Muscles.

Wearable mechatronics for powered orthoses, exoskeletons and prostheses require improved soft actuation systems acting as 'artificial muscles' that are capable of large strains, high stresses, fast response and self-sensing and that show electrically safe operation, low specific weight and large compliance. Among the diversity of soft actuation technologies under investigation, pneumatic devices have been the focus, during the last couple of decades, of renewed interest as an intrinsically soft artificial muscle technology, due to technological advances stimulated by applications in soft robotics. As of today, quite a few solutions are available to endow a pneumatic soft device with linear actuation and self-sensing ability, while also easily achieving these features with off-the-shelf materials and low-cost fabrication processes. Here, we describe a simple process to make self-sensing pneumatic actuators, which may be used as 'inverse artificial muscles', as, upon pressurisation, they elongate instead of contracting. They are made of an elastomeric tube surrounded by a plastic coil, which constrains radial expansions. As a novelty relative to the state of the art, the self-sensing ability was obtained with a piezoresistive stretch sensor shaped as a conductive elastomeric body along the tube's central axis. Moreover, we detail, also by means of video clips, a step-by-step manufacturing process, which uses off-the-shelf materials and simple procedures, so as to facilitate reproducibility.

Novel Acid-Driven Bioinspired Self-Resettable Bilayer Hydrogel Actuator Mimicking Natural Muscles.

Soft robots have great potential applications in manufacturing, disaster rescue, medical treatment, etc. Artificial muscle is one of the most important components of a soft robot. In previous years, hydrogel actuators that can be controllably deformed by the stimuli of external signals have been developed as good candidates for muscle-like materials. In this article, we successfully prepared a chemical fuel-driven self-resettable bilayer hydrogel actuator mimicking natural muscles with the aid of a new negative feedback reaction network. The actuator can temporarily deform upon the addition of H+ (chemical fuel). Subsequently, H+ accelerated the reaction between BrO3- and Fe(CN)64-, which consume H+. It resulted in the spontaneous recovery of the pH as well as the shape of the actuator. Such an actuator exhibits a great similarity with natural muscles in actuation mechanisms and automaticity in the manipulation compared to the widely reported stimuli-responsive hydrogel actuators. This illustrates that fuel-driven self-resettable hydrogel is a promising dynamic material for mimicking the functions of living creatures.

Finger Prosthesis Driven by DEA Pairs as Agonist-Antagonist Artificial Muscles.

Loss of an upper limb exerts a negative influence on an individual's ability to perform their activities of daily living (ADLs), reducing quality of life and self-esteem. A prosthesis capable of performing basic ADLs functions has the capability of restoring independence and autonomy to amputees. However, current technologies present in robotic prostheses are based on rigid actuators with several drawbacks, such as high weight and low compliance. Recent advances in robotics have allowed for the development of flexible actuators and artificial muscles to overcome the limitations of rigid actuators. Dielectric elastomer actuators (DEAs) consist of a thin elastomer membrane arranged between two compliant electrodes capable of changing dimensions when stimulated with an electrical potential difference. In this work, we present the design and testing of a finger prosthesis driven by two DEAs arranged as agonist-antagonist pairs as artificial muscles. The soft actuators are designed as fiber-constrained dielectric elastomers (FCDE), enabling displacement in just one direction as natural muscles. The finger prosthesis was designed and modeled to show bend movement using just one pair of DEAs and was made of PLA in an FDM 3D printer to be lightweight. The experimental results show great agreement with the proposed model and indicate that the proposed finger prosthesis is promising in overcoming the limitations of the current rigid based actuators.

Effective On-Line Performance Modulation and Efficient Continuous Preparation of Ultra-Long Twisted and Coiled Polymer Artificial Muscles for Engineering Applications.

Artificial muscle is a kind of thread-like actuator that can produce contractile strain, generate force, and output mechanical work under external stimulations to imitate the functions and achieve the performances of biological muscles. It can be used to actuate various bionic soft robots and has broad application prospects. The electrically controlled twisted and coiled polymer (TCP) artificial muscles, with the advantages of high power density, large stroke and low driving voltage, while also being electrolyte free, are the most practical. However, the relationship between the muscle performances and its preparation parameters is not very clear yet, and the complete procedure of designing and preparing TCP muscles according to actual needs has not been established. Besides, current preparation approaches are very time-consuming and cannot make ultra-long TCP muscles. These problems greatly limit wide applications of TCP artificial muscles. In this study, we studied and built the relationship between the actuating performances of TCP muscles and their preparation parameters, so that suitable TCP muscles can be easily designed and prepared according to actual requirements. Moreover, an efficient preparation method integrating one-step annealing technique has been developed to realize on-line performance modulation and continuous fabrication of ultra-long TCP muscles. By graphically assembling long muscles on heat-resist films, we designed and produced a series of fancy soft robots (butterfly, flower, starfish), which can perform various bionic movements and complete specific tasks. This work has achieved efficient on-demand preparation and large-scale assembly of ultra-long TCP muscles, laying solid foundations for their engineering applications in soft robot field.

Design and Force/Angle Independent Control of a Bionic Mechanical Ankle Based on an Artificial Muscle Matrix.

Inspired by the natural skeletal muscles, this paper presents a novel shape memory alloy-based artificial muscle matrix (AMM) with advantages of a large output force and displacement, flexibility, and compactness. According to the composition of the AMM, we propose a matrix control strategy to achieve independent control of the output force and displacement of the AMM. Based on the kinematics simulation and experiments, we obtained the output displacement and bearing capacity of the smart digital structure (SDS) and confirmed the effectiveness of the matrix control strategy to achieve force and displacement output independently and controllably. A bionic mechanical ankle actuated by AMM was proposed to demonstrate the actuating capability of the AMM. Experimental results show that the angle and force of the bionic mechanical ankle are output independently and have a significant gradient. In addition, by using a self-sensing method (resistance self-feedback) and PD control strategy, the output angle and force of the bionic mechanical ankle can be maintained for a long time without overheating of the AMM.

High-Performance One-Body Electrochemical Torsional Artificial Muscles Built Using Carbon Nanotubes and Ion-Exchange Polymers.

Electrochemical torsional artificial muscles have the potential to replace electric motors in the field of miniaturization. In particular, carbon nanotubes (CNTs) are some of the best materials for electrochemical torsional artificial muscles due to their remarkable mechanical strength and high electrical conductivity. However, previous studies on CNT torsional muscle utilize only half of the whole potential range for torsional actuation because the actuations in the positive and negative voltage ranges offset each other. Here, we used an ion-exchange polymer, poly(sodium 4-styrenesulfonate) (PSS), which leads to the participation of only positive ions in the actuation of CNT muscles so that the whole potential range can be used for torsional actuation. As a result, PSS-coated CNT muscle can provide 1.9 times higher torsional actuation compared to neat CNT torsional muscle. This PSS-coated CNT muscle not only provides high performance but also facilitates a one-body system for electrochemical torsional actuation. From these advantages, we implement a one-body torsional muscle for the realization of the forward motion of a model boat. This high performance and one-body structure for electrochemical torsional muscles can be used for further applications, such as soft robotics and implantable devices.

Ergonomic dual four-bar linkage knee exoskeleton for stair ascent assistance.

Introduction: Robotic exoskeletons are emerging technologies that have demonstrated their effectiveness in assisting with Activities of Daily Living. However, kinematic disparities between human and robotic joints can result in misalignment between humans and exoskeletons, leading to discomfort and potential user injuries. Methods: In this paper, we present an ergonomic knee exoskeleton based on a dual four-bar linkage mechanism powered by hydraulic artificial muscles for stair ascent assistance. The device comprises two asymmetric four-bar linkage mechanisms on the medial and lateral sides to accommodate the internal rotation of the knee and address the kinematic discrepancies between these sides. A genetic algorithm was employed to optimize the parameters of the four-bar linkage mechanism to minimize misalignment between human and exoskeleton knee joints. The proposed device was evaluated through two experiments. The first experiment measured the reduction in undesired load due to misalignment, while the second experiment evaluated the device's effectiveness in assisting stair ascent in a healthy subject. Results: The experimental results indicate that the proposed device has a significantly reduced undesired load compared to the traditional revolute joint, decreasing from 14.15 N and 18.32 N to 1.88 N and 1.07 N on the medial and lateral sides, respectively. Moreover, a substantial reduction in muscle activities during stair ascent was observed, with a 55.94% reduction in surface electromyography signal. Discussion: The reduced undesired load of the proposed dual four-bar linkage mechanism highlights the importance of the adopted asymmetrical design for reduced misalignment and increased comfort. Moreover, the proposed device was effective at reducing the effort required during stair ascent.

A Smart, Textile-Driven, Soft Exosuit for Spinal Assistance.

Work-related musculoskeletal disorders (WMSDs) are often caused by repetitive lifting, making them a significant concern in occupational health. Although wearable assist devices have become the norm for mitigating the risk of back pain, most spinal assist devices still possess a partially rigid structure that impacts the user's comfort and flexibility. This paper addresses this issue by presenting a smart textile-actuated spine assistance robotic exosuit (SARE), which can conform to the back seamlessly without impeding the user's movement and is incredibly lightweight. To detect strain on the spine and to control the smart textile automatically, a soft knitting sensor that utilizes fluid pressure as a sensing element is used. Based on the soft knitting hydraulic sensor, the robotic exosuit can also feature the ability of monitoring and rectifying human posture. The SARE is validated experimentally with human subjects (N = 4). Through wearing the SARE in stoop lifting, the peak electromyography (EMG) signals of the lumbar erector spinae are reduced by 22.8% ± 12 for lifting 5 kg weights and 27.1% ± 14 in empty-handed conditions. Moreover, the integrated EMG decreased by 34.7% ± 11.8 for lifting 5 kg weights and 36% ± 13.3 in empty-handed conditions. In summary, the artificial muscle wearable device represents an anatomical solution to reduce the risk of muscle strain, metabolic energy cost and back pain associated with repetitive lifting tasks.

Fabrication and Characterization of Cu2+-Driven PTFE-Reinforced Artificial Muscle Polymer Membrane for Water Purification and Energy Harvesting Applications.

Ionic polymer membranes have not yet gained widespread practical application in areas such as water purification and energy harvesting due to their high cost and tendency to swell. The present study involved the fabrication of reinforced textile structures composed of polytetrafluoroethylene (PTFE)-reinforced Nafion membranes coated with non-precious metals, copper and silver, as a surface electrode by applying a chemical decomposition technique. Several mechanical, contact angle measurement and dielectric tests were conducted on membranes to evaluate their mechanical, wettability and conductivity properties. From scanning electron microscopy, it is clear that the formation of surface electrodes with uniform dispersion of metal particles. Scratch test reveals the adhesive strength between the coated metal particles and membrane. The silver-activated copper-coated membrane has a high contact angle of 121°. Thus, the fabricated membranes can have good antibacterial and adsorption properties for water treatment. The copper-coated membrane has a high Young's modulus of 779 ± 80 MPa and a tensile strength of 29.1 ± 8 MPa, whereas the elongation at break is more for silver-activated copper-coated samples recorded as 158 ± 4%. The viscoelastic behavior of the membranes was analyzed through dynamic mechanical analysis (DMA). A sharp rise in the storage modulus (E') value of 4.8 × 1010 Pa at ~80 °C at a frequency of 1 Hz on metal surface electrodes signifies an improvement in the strength of the material in comparison to the initial pure membrane. The successful enhancement of conductivity on the membrane surface via chemical deposition on the silver-activated membrane is 1 × 10-4 (S/cm) and holds great potential for facilitating voltage transmission through the tribolayer in the nanogenerators.