Preparation of chitosan/Tenebrio molitor larvae protein/curcumin active packaging film and its application in blueberry preservation.

With growing concerns about postharvest spoilage of fruits, higher requirements have been placed on high-performance and sustainable active packaging materials. In this study, we prepared curcumin-based functional composite films using chitosan (CS) and Tenebrio molitor larvae protein (TMP) as the substrates. The effects of curcumin concentration on the structural and physicochemical properties of the composite films were determined. Curcumin was equally distributed in the polymer film through physical interactions. Furthermore, the curcumin composite film with 0.3 % addition exhibited a 27.39 % increase in elongation at break (EBA), a 37.04 % increase in the water vapor barrier, and strong UV-blocking properties and antioxidant activity compared with the control film (CS/TMP). The degradation experiment of the composite film on natural soil revealed that the composite film exhibited good biodegradability and environmental protection. Furthermore, the applicability of functional composite films for preserving blueberries was investigated. Compared with the control film and polyethylene (PE) films, the prepared composite films packaging treatment reduced the decay rate and weight loss rate of blueberries during storage, delayed softening and aging, and maintained the quality of blueberries. Using sustainable protein resources (TMP) and natural polysaccharides as packaging materials provides an economically, feasible and sustainable way to achieve the functional preservation of biomass materials.

Development of ternary polymeric film based on modified mango seed kernel starch, carboxymethyl cellulose, and gum acacia to extend the shelf-life of bun-bread.

Non-conventional starch sources have attracted substantial attention due to their preferred physicochemical and mechanical properties similar to conventional sources. This study aimed to enhance the mechanical properties of mango seed kernel starch (MSKS) based films reinforced with carboxymethyl cellulose (CMC) and gum acacia (GA). Physical modification of MSKS was carried out using microwave-assisted at 180 W for 1 min. SEM results confirmed the oval and irregular shape of starch. The particle size of native starch (NS) (754.9 ± 20.4 nm) was higher compared to modified starch (MS) 336.6 ± 88.9 nm with a surface charge of -24.80 ± 3.92 to -34.87 ± 3.92 mV, respectively. Several functional groups including hydroxyl (OH) and carboxyl (CH) were confirmed in NS and MS. Different ratios of the MS, NS, CMC, and GA were used for the fabrication of films. Results revealed the higher tensile strength of M/C/G-1 (57.45 ± 0.05 nm) and M/C/G-2 (50.77 ± 0.58), compared to control C-4 (100 % native starch) (4.82 ± 0.04) respectively. The ternary complex provided excellent permeability against moisture and the film with a higher starch concentration confirmed the uniform thickness (0.09-0.10 mm). Furthermore, selected films (M/C/G-1 and M/C/G-2) reduced the microbial growth and weight loss of the bun compared to the control (C-4) film. Thus, the ternary complex maintained the freshness of the bun-bread for 14 days. It can be potentially used as a cost-effective and eco-friendly packaging material for food applications.

Development of chitosan-based edible film incorporated with purified flavonoids from Moringa oleifera: Structural, thermal, antibacterial activity and application.

Purified flavonoids (PF) from Moringa oleifera leaves were incorporated in chitosan (CS) polymer at different concentrations (0.5-4%) to produce a novel edible film. The physical, structure, mechanical, and bio-functional characterizations of the film were evaluated. The incorporation of PF significantly (p < 0.05) improved the thickness, solubility, swelling, and color of CS-films. Incorporating 4% of Moringa oleifera purified flavonoids (MOPF) improved the water vapor permeability from 8.85 to 2.47 g-1 s-1 Pa-1, and increased the film surface heterogeneity observed by SEM. Results also indicated that PF enhanced the mechanical properties and thermal stability of CS-films. The FTIR results indicated alterations in the CS-MOPF composite films' characteristics. Additionally, the incorporation of MOPF increased the antioxidation capacity. Furthermore, 4% of MOPF inhibited the activity of pathogenic bacteria in packed beef burgers. These results suggest that CS-MOPF composite films with enhanced technological and bio-functional properties could be industrially applied to increase the shelf-life of packaged foods.

A review of advancements in chitosan-essential oil composite films: Better and sustainable food preservation with biodegradable packaging.

In response to the environmental pollution caused by non-degradable and non-recyclable plastic packaging films (PPFs) and the resulting health concerns due to the migration of microplastics into food, the development of biodegradable food packaging films has gained great attention. Chitosan has been extensively utilized in the food industry owing to its abundant availability, exceptional biocompatibility, degradability, and antimicrobial properties. Chitosan-essential oil composite films (CEOs) represent a promising avenue to replace conventional PPFs. This review provides an overview of the advancements in CEOs over the past decade, focusing on the effects of essential oils (EOs) on CEOs in terms of antimicrobial activity, antioxidant effect, gas barrier, light barrier, and mechanical properties. It also offers insights into the controlled release of EOs in CEOs and summarizes the application of CEOs in fresh food preservation.

Exploring urea as a prospective auxiliary for starch functionalization: A concise review on modified starch properties and the sustainable packaging films.

Urea is also known as carbamide, an inexpensive and eco-friendly additive for starch functionalization. This article reviews the potential role of urea in starch modification, with the prominence of the mechanism of urea action, alterations in the starch structure and functional properties. In addition, current literature conveys the prospective effect of urea in fabricating starch films for food packaging, and the relevant areas that need to be covered in the forthcoming research are specified at the end of the article section. Urea can modify the diverse physico-chemical and functional properties of starch. Starch-based films exhibit pronounced effects on their mechanical and barrier properties upon the incorporation of urea, although this effect strongly depends on the urea content and degree of substitution (DS). Overall, urea holds great potential for use in the starch and bioplastic film industries, as it produces biocompatible derivatives with desirable performance.

Preparation of films based on reticulated fish gelatin containing garlic essential oil.

Agro-industrial co-products, such as fish gelatin, stand out for their capacity in forming biopolymeric films, being biocompatible and non-toxic; however, its hydrophilicity poses a challenge. Essential oils, rich in bioactives, attract research interest aiming to enhance the protective barrier of films and enable their application in packaging. This study produced films based on cross-linked Nile tilapia skin gelatin, incorporating garlic essential oil. Gelatin obtained through partial collagen hydrolysis from the fish skin and cross-linked with gallic acid had hydroxyproline content of 10.02 g 100 g-1 and gel strength of 287 g, which were consistent with other studies. Oil extraction used supercritical CO2 as a solvent and ethanol as a cosolvent, following a factorial experimental design, evaluating the extraction temperature (40 °C and 70 °C) and cosolvent ratio (1:1 and 1:3), with three central points. Extraction was successful, with higher yields on a dry basis at 70 °C (88.35 %), using a 1:1 cosolvent ratio. Films incorporated with oil exhibited lower water vapor permeability (WVP) than those with only cross-linked gelatin (1.59 (g m-1 s-1 Pa-1) 1011). The film with the most suitable tensile strength (19.07 MPa), elongation (120.91 %), and WVP (1.09 (g m-1 s-1 Pa-1) 1011) properties contained garlic oil extracted at the central point (55 °C and 1:2). Thermal analysis indicated increased melting temperatures in films with added oil, suggesting low thermal degradation. These results suggest that garlic oil addition can improve the properties of fish gelatin-based films, making them promising for biodegradable packaging.

Chitosan-based nanocomposite films with carnauba wax, rosin resin, and zinc oxide nanoparticles.

This work aimed to develop edible emulsion-based barriers in the form of chitosan composite films, with a focus on assessing the impacts of carnauba wax, rosin resin, and zinc oxide nanoparticles on their properties. Six films were produced by casting using chitosan as polymer base and glycerol as plasticizer. Acetic acid and polysorbate 80 were also used to facilitate the dissolution and mixing of the components. The six filmogenic solutions contained chitosan at 1.2% w/v, wax or resin content with 0 or 0.6% m/v and ZnO with 0 or 0.05% m/v. The dried films were characterized according to their chemical, barrier, mechanical, thermal and optical properties. All treatments resulted in flexible films. Chitosan films appeared smoother and more uniform under SEM imaging, while carnauba wax films displayed roughness due to their hydrophobic nature. Wax and resin films were less transparent and water soluble than the chitosan-only films. On the other hand, the addition of ZnO in the formulations increased the solubility of the films. The sorption degree was in line with the solubility results, i.e., films with ZnO presented higher sorption degree and solubility values. All treatments showed low or non-light UV transmission, indicating that the films provide good barrier to UV light. In the visible light region, films of resin with ZnO showed the lowest transmittance values, hence offering a good barrier to visible light. Among the evaluated films, chitosan, and resin films with ZnO nanoparticles were more rigid and resistant to deformation. Overall, films produced with rosin resin and ZnO nanoparticles showed potential improvements in barrier, mechanical, thermal, and optical properties, mainly due to their low water solubility, good UV protection and low permeability to water vapor and oxygen, which are suitable for using in formulations, intended to produce edible films and coatings.

Use of sustainable packaging materials for fresh beef vacuum packaging application and product assessment using physicochemical means.

Packaging material should guarantee the longest possible shelf life of food and help to maintain its quality. The aim of the study was to assess the physicochemical changes taking place during 28-day ageing of beef steaks packed in two types of multilayer films containing biodegradable polymers - polylactic acid (NAT/PLA) and Mater-Bi® (NAT/MBI). The control group consisted of steaks packed in synthetic polyamide/polyethylene (PA/PE) film. The samples stored in NAT/PLA had significantly lower purge loss than the control samples and the lowest expressible water amount after 14 and 21 days. Following blooming, the most favourable colour was shown in steaks stored in NAT/MBI, with the highest values for the L*, a* and C* parameters and the R630/580 ratio, a high proportion of oxymyoglobin, and the lowest share of metmyoglobin. All steaks, regardless of the type of packaging material, had acceptable tenderness and were stable in terms of lipid oxidation.

Biodegradable, UV-blocking, and antioxidant films from alkali-digested lignocellulosic residue fibers of switchgrass.

The development of bio-friendly materials to replace single-use plastics is urgently needed. In this regard, cellulosic material from plants is a promising alternative. However, due to the risk of forest depletion, agricultural biomass stands out as a favorable choice. Toward this end, switchgrass, an underutilized grass, presents itself as a viable source of lignocellulose that can be turned into a bio-friendly material. Herein, lignocellulosic residue from switchgrass has been extracted using two different concentrations of NaOH (20% and 50% w/v), solubilized in aqueous ZnCl2 solution, and crosslinked with CaCl2 (200, 300, 400, and 500 mM) to prepare biodegradable films. The color, thickness and moisture, water solubility, water absorption, water vapor permeability, tensile strength and elongation, biodegradation, UV transmittance, and antioxidant activity of films have been studied. The films possess a high tensile strength of 14.7 MPa and elongation of 4.7%. They block UVB-radiation and hold antioxidant properties. They display good water vapor permeability of 1.410-1.6 × 10-11 gm-1s-1Pa-1 and lose over 80% of their weight at 30% soil moisture within 40 days. An increase in the CaCl2 amount decreased the water vapor permeability, elongation, UV transmittance, and biodegradation but increased the transparency, tensile strength and antioxidant property. Overall, films of alkali-digested lignocellulosic residue of switchgrass showed excellent potential to be used against lightweight plastics and support the circular economy.

Amine Switchable Hydrophilic Solvent Vortex-Assisted Homogeneous Liquid-Liquid Microextraction and GC-MS for the Enrichment and Determination of 2, 6-DIPA Additive in Biodegradable Film.

2, 6-diisopropylaniline (2, 6-DIPA) is a crucial non-intentionally organic additive that allows the assessment of the production processes, formulation qualities, and performance variations in biodegradable mulching film. Moreover, its release into the environment may have certain effects on human health. Hence, this study developed simultaneous heating hydrolysis-extraction and amine switchable hydrophilic solvent vortex-assisted homogeneous liquid-liquid microextraction for the gas chromatography-mass spectrometry analysis of the 2, 6-DIPA additive and its corresponding isocyanates in poly(butylene adipate-co-terephthalate) (PBAT) biodegradable agricultural mulching films. The heating hydrolysis-extraction conditions and factors influencing the efficiency of homogeneous liquid-liquid microextraction, such as the type and volume of amine, homogeneous-phase and phase separation transition pH, and extraction time were investigated and optimized. The optimum heating hydrolysis-extraction conditions were found to be a H2SO4 concentration of 2.5 M, heating temperature of 87.8 °C, and hydrolysis-extraction time of 3.0 h. As a switchable hydrophilic solvent, dipropylamine does not require a dispersant. Vortex assistance is helpful to speed up the extraction. Under the optimum experimental conditions, this method exhibits a better linearity (0.0144~7.200 µg mL-1 with R = 0.9986), low limit of detection and quantification (0.0033 µg g-1 and 0.0103 µg g-1), high extraction recovery (92.5~105.4%), desirable intra- and inter-day precision (relative standard deviation less than 4.1% and 4.7%), and high enrichment factor (90.9). Finally, this method was successfully applied to detect the content of the additive 2, 6-DIPA in PBAT biodegradable agricultural mulching films, thus facilitating production process monitoring or safety assessments.

Enhancing Mechanical Properties of Corn Bran Arabinoxylan Films for Sustainable Food Packaging.

Arabinoxylan (AX)-based films can improve the mechanical characteristics of biodegradable materials when utilized for food packaging. However, the mechanical properties of AX films for food packaging applications require thorough investigation to establish their viability. In this study, AX was extracted from corn bran coproducts of dry-milling (DCB), wet-milling (WCB), and dried distiller's grains with solubles (DDGS) using an acid-alkali method. Packaging materials were produced using these AX extracts, each combined with laccase and sorbitol, forming the basis for three different films. These films were then modified by immersing the surface in a lipase-acetate solution. We evaluated their mechanical characteristics, including thickness, tensile properties, tear resistance, and puncture resistance. The thickness and tensile properties of the modified AX films derived from DCB and DDGS showed significant improvements (p < 0.05) compared to the unmodified AX films. In contrast, the modified AX films from WCB showed no significant changes (p > 0.05) in thickness and tensile properties compared to the unmodified WCB AX films. A significant increase in tear resistance (p < 0.05) was observed in all modified AX films after immersion in the lipase-acetate mixture. While puncture resistance was enhanced in the modified AX films, the improvement was not statistically significant (p > 0.05) compared to the unmodified films. The presence of hydroxyl (OH) and carbonyl (CO) groups on the surfaces of AX films from DCB and DDGS, modified by the lipase-acetate solution, suggests excellent biodegradability properties. The modification process positively affected the AX films, rendering them more bendable, flexible, and resistant to deformation when stretched, compared to the unmodified AX films.

Effect of Adding Red Propolis to Edible Biodegradable Protein Films for Coating Grapes: Shelf Life and Sensory Analysis.

Red propolis is an active ingredient of great nutritional interest which offers numerous benefits as an antioxidant and antimicrobial agent. Thus, the objective of this research was to evaluate the application of an edible and antimicrobial gelatine coating containing red propolis to increase the shelf life of grapes. Gelatine films with an addition of 5, 10, 15, 20 and 25% of red propolis extract were produced to evaluate their antimicrobial activity using the disk diffusion test in solid media. The films with 25% red propolis extract showed antimicrobial activity against the bacteria Staphylococcus aureus and Pseudomonas aeruginosa. The grapes were coated with pure gelatine, without a plasticizer and with gelatine with 25% red propolis and then stored for 1, 4, 10, 19 and 25 days at temperatures of 25 °C and 5 °C. The results showed that the gelatine coating with propolis reduced the mass loss of grapes stored at 25 °C for 19 days by 7.82% and by 21.20% for those kept at 5 °C for 25 days. The pH, total titratable acidity, soluble solids and color of the grapes increased due to the ripening process. Furthermore, the sensory acceptability indexes of the refrigerated grapes with coatings were superior (>78%) to those of the control samples (38%), proving the effectiveness of the coatings in maintaining the quality of grapes during storage.

Recent advances in extruded polylactic acid-based composites for food packaging: A review.

This review article provides a comprehensive overview of recent progress in polylactic acid (PLA) extrusion, emphasizing its applications in food packaging. PLA has witnessed a significant rise in demand, particularly within the food packaging sector. A notable increase in research publications has been observed in recent years, exploring the extrusion of PLA and PLA-based composite films. In comparison to conventional techniques such as solvent casting, extrusion offers advantages in scalability and environmental sustainability, especially for industrial-scale production. The benefits of this method include faster drying times, enhanced flexibility, consistent film thickness, and less structural defects. Extensive research has focused on the effect of various PLA blends on film properties, including flexibility, elongation, and barrier properties against water vapour and gases. Furthermore, the incorporation of compounds such as antioxidants, antimicrobials, and natural pigments has enabled the development of active and intelligent PLA-based packaging. This article summarizes the types of additives employed to enhance the physicochemical properties of extruded PLA and film performance. Additionally, this article explores the diverse applications of extruded PLA in active and intelligent packaging for various food products.

Recent advances in modified starch based biodegradable food packaging: A review.

This study reviews the importance of resistant starch (RS) as the polymer of choice for biodegradable food packaging and highlights the RS types and modification methods for developing RS from native starch (NS). NS is used in packaging because of its vast availability, low cost and film forming capacity. However, application of starch is restricted due to its high moisture sensitivity and hydrophilic nature. The modification of NS into RS improves the film forming characteristics and extends the applications of starch into the formulation of packaging. The starch is blended with other bio-based polymers such as guar, konjac glucomannan, carrageenan, chitosan, xanthan gum and gelatin as well as active ingredients such as nanoparticles (NPs), plant extracts and essential oils to develop hybrid biodegradable packaging with reduced water vapor permeability (WVP), low gas transmission, enhanced antimicrobial activity and mechanical properties. Hybrid RS based active packaging is well known for its better film forming properties, crystalline structures, enhanced tensile strength, water resistance and thermal properties. This review concludes that RS, due to its better film forming ability and stability, can be utilized as polymer of choice in the formulation of biodegradable packaging.

Soil burial-induced degradation of cellulose films in a moisture-controlled environment.

In this study, the biodegradability of cellulose films was evaluated in controlled-moisture soil environments. The films were prepared from low-quality cotton fibers through dissolution in DMAc/LiCl, casting, regeneration, glycerol plasticization, and hot-pressing. Two soil burial degradation experiments were conducted in August 2020 (11th August to 13th October) and March 2021 (24th March to 24th July) under controlled moisture conditions to assess the biodegradation behavior of cellulose films. The films were retrieved from soil beds at seven-day intervals, and morphological and physicochemical changes in the films were investigated. The results indicated that the cellulose films exhibited gradual changes starting on Day 7 and major changes after Day 35. Stereomicroscopy images showed the growth and development of fungal mycelia on the surface of the films, and FTIR spectroscopy confirmed the presence of biomolecules originating from microorganisms. The tensile strength and elongation of cellulose films were significantly reduced by 64% and 96% in the first experiment and by 40% and 94% in the second experiment, respectively, during the degradation period. Degradation also significantly impacted the thermal stability (14% and 16.5% reduction, respectively, in the first and second studies) of the films. The cellulose-based films completely degraded within 63 days in late summer and 112 days in spring. This study demonstrates that, unlike synthetic plastics, films prepared from low-quality cotton fibers can easily degrade in the natural environment.

Effect of Starch Plasticization on Morphological, Mechanical, Crystalline, Thermal, and Optical Behavior of Poly(butylene adipate-co-terephthalate)/Thermoplastic Starch Composite Films.

Starches plasticized with glycerol/citric acid/stearic acid and tributyl 2-acetylcitrate (ATBC), respectively, were processed with poly (butylene adipate-Co-terephthalate (PBAT) via extrusion and a film-blown process. All the composite films were determined for morphology, mechanical, thermal stability, crystalline, and optical properties. Results show that the most improved morphology was in the 30% glycerol plasticized PBAT/thermoplastic starch (TPS) composite films, characterized by the smallest and narrowest distribution of TPS particle sizes and a more uniform dispersion of TPS particles. However, the water absorption of PBAT/TPS composite films plasticized with glycerol surpassed that observed with ATBC as a plasticizer. Mechanical properties indicated insufficient plasticization of the starch crystal structure when using 10% ATBC, 20% ATBC, and 20% glycerol as plasticizers, leading to poor compatibility between PBAT and TPS. This resulted in stress concentration points under external forces, adversely affecting the mechanical properties of the composites. All PBAT/TPS composite films exhibited a negative impact on the initial thermal decomposition temperature compared to PBAT. Additionally, the haze value of PBAT/TPS composite films exceeded 96%, while pure PBAT had a haze value of 47.42%. Films plasticized with 10% ATBC, 20% ATBC, and 20% glycerol displayed lower transmittance values in the visible light region. The increased transmittance of films plasticized with 30% glycerol further demonstrated their superior plasticizing effect compared to other PBAT/TPS composite films. This study provides a simple and feasible method for preparing low-cost PBAT composites, and their extensions are expected to further replace general-purpose plastics in daily applications.

Bio-nanocomposite active packaging films based on carboxymethyl cellulose, myrrh gum, TiO2 nanoparticles and dill essential oil for preserving fresh-fish (Cyprinus carpio) meat quality.

This study developed a composite film for packaging refrigerated common carp fillets using carboxymethyl cellulose (CMC) (1.5 % w/v)/Myrrh gum (MG) (0.25 % w/v) base with the addition of titanium dioxide nanoparticles (TiO2 NPs) (0.25 %, 0.5 %, and 1 %) and Dill essential oil (DEO) (1.5 %, 2.25 %, and 3 %). The film was produced using a casting method and optimized for mechanical and barrier properties. The incorporation of DEO and TiO2 NPs into CMC/MG composite films significantly reduced moisture content (MC) and water vapor permeability (WVP), improved their tensile strength (TS), and increased their antimicrobial and antioxidant properties. Moreover, MG can improve the physicomechanical properties of the CMC/MG composite films. The film components had good compatibility without significant aggregation or cracks. In conclusion, the optimized CMC/MG (1.5 %/0.25 %) film containing TiO2 NPs (0.5 %), and DEO (2.25 %) has the best overall performance and can be a good source for making edible film. Functionally, this bioactive nanocomposite film significantly increased the shelf life of refrigerated fish fillet samples for 12 days by inhibiting microbial growth and reducing the oxidation rate compared to the control sample. The knowledge obtained from this study can guide the development of bio-nanocomposite and biodegradable food packaging films based on CMC/MG to increase the shelf life of food products and environmental protection.

Valorization of guinea grass seed (Megathyrsus maximus): Synthesis and utilization of cellulose microfiber to reinforce esterified and cross-linked guinea starch films.

The present study extracts starch from guinea grass seed and fiber from the starch extraction residue. The fibrous residue was chemically converted into cellulose microfiber (CMF) and used to reinforce the native, esterified and crosslinked guinea starch films. The films were developed with 5 % starch, 40 % glycerol and 0, 2.5, 5, and 10 % CMF based on the dry matter of starch. SEM images of all film samples showed good compatibility of CMF with starch molecules, and no fractures or pores were observed. Adding filler materials to modified starch films slightly increased the film thickness (0.24 to 0.30 mm) due to the high dimensions of CMF, which comprise a significant amount of the composite's volume. A synergetic effect of starch modification and CMF in films decreased the moisture content (21.98 to 9.21 %), water solubility (25.65 to 15.47 %), water vapor permeability (6.96×10-7 to 1.65×10-7g∙mm2∙day∙Pa), and elongation at the break (33.51 to 16.79 %) while increasing the tensile strength (1.84 to 3.85 MPa) and Young's modulus (5.49 to 22.93 MPa). The L* and a* values of the films decreased, and the b* and opacity values of the films increased with the addition of CMF. The XRD graph showed that all films have semicrystalline structures with peaks at 18°, 20°, and 22°, and the degree of crystallinity increases (32.3 to 55.1 %) with CMF. All film samples showed good thermal stability up to 315 °C. In conclusion, esterified starch-based films exhibited superior barrier properties and flexibility. On the contrary, cross-linked starch films demonstrated higher tensile strength and lower water solubility.

Enhanced physical properties, antioxidant and antibacterial activity of bio-composite films composed from carboxymethyl cellulose and polyvinyl alcohol incorporated with broccoli sprout seed extract for butter packaging.

This study investigated the development of biodegradable films made from a combination of carboxymethyl cellulose (CMC), Polyvinyl alcohol (PVA), and purified extract of broccoli sprout seed (BSSE). The films were characterized for their color, physical properties, surface morphology, crystallinity, mechanical properties, and thermal properties. The addition of BSSE up to 1.4 % to the film matrix imparted opaque color and increased opacity up to 3.652. The films also became less moisture-absorbent 8.21 %, soluble 19.16 %, and permeable to water vapor 1.531 (× 10-10 g.m-1 s-1 pa-1). By utilizing 0.7 % from BSSE inside films, the surface of the films became smoother but became rough with higher concentrations 2.1 % of BSSE. Fourier transform infrared (FT-IR) analysis showed that there was physical interaction between the BSSE extract and the PV/CM matrix. The films showed good thermal stability, and the incorporation of BSSE improved their ability to preserve the acidity, TBARS, peroxide value, and total color differences of butter during cold storage.

Preparation and characterization of hemicellulose films reinforced with amino polyhedral oligomeric silsesquioxane for biodegradable packaging.

Biomass is one of the powerful alternatives to petroleum-based packaging materials. Herein, carboxymethyl hemicellulose (CMH) based films (CPF) were prepared using a convenient strategy. The chains of CMH provided the necessary supporting matrix, and the aminopropyl polyhedral oligomeric silsesquioxane (POSS-NH2) regulated the thermal and barrier properties of the CPF. The secondary amide groups and hydrogen bond were appeared in chemical structure, and SEM-EDS results indicated the preferable dispersion and compatibility of POSS-NH2 in CPFs. The thermal degradation temperature (Tonset > 260 °C), the coefficient of linear thermal expansion and glass transition temperature (Tg > 130 °C) have been improved by introduction of POSS-NH2. The tensile strength of CPF showed a higher level of 39.43 MPa with the POSS-NH2 loading of 20 wt%, which was 18.8 % higher than that of CMH film. More importantly, water vapor barrier property of films almost improved by two times, and its value is reduced to 18.82 g m-2 h-1. The shelf life of blueberry was effectively extended by the CPF coating for one week compared with commercial PE film. Therefore, CPF films displayed effective thermal performances, water vapor barrier characteristic and biodegradability, which might be exploited in packaging material for food application.