Determination of Free Glycidol and Total Free Monochloropropanediol in Fish and Krill Oil with Simple Aqueous Derivatization and High-Performance Liquid Chromatography-Tandem Mass Spectrometry.

This study introduces a novel method for detecting free glycidol and total free monochloropropanediol (MCPD) in fish and krill oil. Before analysis on high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS), p-(dimethylamino)phenol was used for derivatization of these compounds, enabling the sensitive determination of these contaminants. The sample preparation procedure includes a simple, efficient pretreatment using NaCl aqueous solution extraction and C18 sorbent cleanup (for demulsification), distinguishing glycidol from MCPD under varied reaction conditions for derivatization (weak acidic and strong alkaline aqueous environments). This approach shows broad linearity from 1 to at least 256 ng·mL-1, improved sensitivity compared to standard GC-MS methods, with the limit of detection (LOD) and limit of quantification (LOQ) for MCPD and glycidol in both oil samples verified at 0.5 ng·mL-1 and 1 ng·mL-1, respectively. Different from previous HPLC-MS methods for direct detection of glycidol esters or MCPD esters, this is the first HPLC-MS method used for the detection of free glycidol and total free MCPD in edible oil. Furthermore, this method can be potentially developed for glycidol or monochloropropane diol esters, which is similar to the current official methods adopted for indirect detection of these contaminants in different food matrices. Application of this detection method to real dietary supplements (fish oil and krill oil) revealed MCPD residues in fish oil (maximum detected: 32.78 ng·mL-1) and both MCPD (maximum detected: 2767.3 ng·mL-1) and glycidol (maximum detected: 22.2 ng·mL-1) in krill oil, emphasizing its effectiveness and accuracy for assessing contamination in these supplements.

Determination of multi-residue pesticides in dairy products using single-step emulsification/demulsification clean-up strategy combined with low-pressure gas chromatography-tandem mass spectrometry.

In this study, a simple, sensitive, and rapid method was developed for the simultaneous determination of 99 kinds of pesticides in fatty milk samples. This novel emulsification-demulsification clean-up approach, coupled with an automatic demulsification-dehydration cartridge, allowed rapid single-step clean-up operation and high throughput. It also achieved effective and selective removal of lipids. The analysis was performed using low-pressure gas chromatography-tandem mass spectrometry (LPGC-MS/MS). Based on the optimal conditions, the targeted pesticides showed good linearity in the range of 5-250 µg/kg, with recoveries of 70-120% at spiking levels of 5, 10, and 20 µg/kg in cow milk, goat milk, and almond milk, respectively. The limit of quantification for most pesticides was 5 µg/kg, and the RSDs were lower than 20%. Analysis of real dairy products obtained from local markets revealed a potential risk in plant-derived almond milk, but no significant risks were found for cow and goat milk.

Characteristic and stability changes of peanut oil body emulsion during the process of demulsification using heptanoic acid.

In this paper, the changes in oil body emulsion (OBE) during heptanoic acid demulsification (HD) were investigated from the macro and microscopic points of view. Specifically, the OBE particle size increased from 3.04 to 8.41 µm, while the zeta potential absolute decreased to 2.89 mV. The interfacial tension and apparent viscosity of OBE were reduced significantly. Heptanoic acid could contribute to oil droplets aggregation. The findings indicated that high-molecular proteins, including lipoxygenase (97.58 kDa) and arachin (70.28 kDa), detached from the OBs' interface. HD caused alterations in the secondary structure of protein and the environment around proteins changed. The HD mechanism was speculated that the addition of heptanoic acid resulted in the reduction in pH and changes of environment surrounding OBE, which triggered polymerization and the phase transformation of the oil droplets. Overall, this study is vital for solving the problem of demulsification during aqueous enzymatic extraction (AEE).

Demulsification with simultaneous water purification by coupling filtration and enhanced oil droplet coalescence at anode interface in an electrochemical reactor.

With the increasing demand of recycling disposal of industrial wastewater, oil-in-water (O/W) emulsion has been paid much attention in recent years owing to its high oil content. However, due to the presence of surfactant and salt, the emulsion was usually stable with complex physicochemical interfacial properties leading to increased processing difficulty. Herein, a novel flow-through electrode-based demulsification reactor (FEDR) was well designed for the treatment of saline O/W emulsion. In contrast to 53.7% for electrical demulsification only and 80.3% for filtration only, the COD removal efficiency increased to 92.8% under FEDR system. Moreover, the pore size of electrode and the applied voltage were two key factors that governed the FEDR demulsification performance. By observing the morphology of oil droplets deposited layer after different operation conditions and the behavior of oil droplets at the electrode surface under different voltage conditions, the mechanism was proposed that the oil droplets first accumulated on the surface of flow-through electrode by sieving effect, subsequently the gathered oil droplets could further coalesce with the promoting effect of the anode, leading to a high-performing demulsification. This study offers an attractive option of using flow-through electrode to accomplish the oil recovery with simultaneous water purification.

Facile Synthesis of Novel Magnetic Janus Graphene Oxide for Efficient and Recyclable Demulsification of Crude Oil-in-Water Emulsion.

Nanoparticles have been widely applied to treat emulsion-containing wastewater in the form of chemical demulsifiers, such as SiO2, Fe3O4, and graphene oxide (GO). Owing to their asymmetric structures and selective adsorption, Janus nanoparticles show greater application potential in many fields. In the present work, the novel magnetic Janus graphene oxide (MJGO) nanoparticle was successfully prepared by grafting magnetic Fe3O4 to the surface of the JGO, and its demulsifying ability to treat a crude oil-in-water emulsion was evaluated. The MJGO structure and its magnetic intensity were verified by Fourier-transform infrared spectra (FTIR), transmission electron microscopy (TEM), X-ray diffraction (XRD), and magnetization saturation (MS) tests. Compared with GO and JGO, MJGO displayed the superior efficiency (>96%) to demulsify the crude oil-in-water emulsion, which can be attributed to the reduced electrostatic repulsion between MJGO and the emulsion droplets. Furthermore, the effects of pH and temperature on the demulsification performance of MJGO were also studied. Lastly, the recyclability of MJGO largely reduced the cost of demulsifiers in separating crude oil and water. The current research presents an efficient and recyclable demulsifier, which provides a new perspective for the structural design of nanomaterials and their application in the field of demulsification.

Enhanced toxicity-free astaxanthin extraction from Haematococcus pluvialis via concurrent cell disruption and demulsification.

The extraction of astaxanthin from Haematococcus pluvialis involves the utilization of petroleum-derived organic solvents or supercritical CO2, beset by safety concerns, high costs, and environmental sustainability limitations. This study, in contrast, employed a method involving the adjustment of salt concentration, propylene glycol, and vegetable oil fraction to disrupt emulsion in aqueous cell lysates for facilitating the separation of astaxanthin. Under optimized conditions, an astaxanthin-containing oil with a content of 1.88% was obtained even with the use of wet biomass, and four rounds of consecutive extraction resulted in a cumulative recovery yield of 66.41%. This process produced astaxanthin-enriched soybean oil with 9.49 times improved antioxidant capacity that satisfies a requirement for health functional application. Omitting the solvent removal and drying processes, which consume tremendous energy, can reduce the production cost by 2.98 times compared to conventional methods. Consequently, this study suggests an effective technique for producing edible oil containing H. pluvialis-derived astaxanthin.

Synthesis and demulsification performance of a novel low-temperature demulsifier based on trimethyl citrate.

A significant amount of water-in-oil (W/O) emulsion is generated during petroleum extraction. However, the current commercial demulsifiers are expensive to produce and requires high demulsification temperatures, leading to increased energy and economic consumption. To enhance the efficiency of demulsifiers and reduce the cost of demulsifying W/O emulsions, we have successfully developed a novel demulsifier named TCED through a straightforward two-step process. This demulsifier features trimethyl citrate as the hydrophilic core grafted with three hydrophobic chains. Its structure was characterized using EA, FT-IR and 1H NMR spectroscopy, and the demulsification performance was comprehensively evaluated. At a low demulsification temperature of 40 °C, TCED demonstrated a remarkable demulsification efficiency (DE) of 99.06% and 98.74% in emulsions containing water contents of 70% (E70) and 50% (E50), respectively. Especially, a DE of 100% could be obtained in both E70 and E50 emulsions at a concentration of 600 mg/L. Moreover, TCED displayed a high DE even at high salinity levels of 50,000 mg/L and across a wide pH range of 2-10. Additionally, the phase interface was consistently clear after demulsification. To investigate the demulsification mechanism of TCED, various adsorption kinetics experiments were conducted, including measurements of interfacial tension (IFT), surface tension (SFT), interfacial competitive adsorption, and stability of interfacial film. The results obtained from the experiments indicated that TCED possessed remarkable diffusion and replacement capabilities within the emulsions. As a result, it effectively disrupted the original interfacial active substances, such as asphaltenes aggregates found in crude oil. TCED exhibits a high DE at low concentration and temperature. This characteristic highlights its significant potential for low-temperature demulsification applications in the petroleum industry.

Aromatic poly (amino acids) as an effective low-temperature demulsifier for treating crude oil-in-water emulsions.

Amphiphilic aromatic poly (amino acids) polymers were designed as biodegradability demulsifiers with higher aromaticity, stronger polarity, and side chain-like combs. The effects of demulsifier dosage, structural characteristics and emulsion properties such as pH, salinity, and oil content on the demulsification efficiency were investigated. The results show that the poly (L-glutamic-benzyl ester)-block-poly (L-phenylalanine) (PBLG15-b-PPA15) as the demulsifier can remove more than 99.97% of the oil in a 5.0 wt% oil-in-water (O/W) emulsion at room temperature within 2 min. The poly (L-tyrosine)-block-poly (L-phenylalanine) (PTyr15-b-PPA15) with environmental durability demonstrates high effectiveness, universality, and demulsification speed. It achieves a remarkable demulsification efficiency of up to 99.99% for a 20.0 wt% O/W emulsion at room temperature. The demulsification mechanism indicates that demulsifiers have sufficient interfacial activity can quickly migrate to the oil-water interface after being added to the emulsions. Additionally, when demulsifiers are present in a continuous phase in the molecular form, their "teeth" side chains are beneficial for increasing coalescence and flocculation capacities. Furthermore, according to the Density Functional Theory (DFT) calculations, enhancing the intermolecular interactions between demulsifiers and the primary native surfactants that form an oil-water interfacial film is a more efficient approach to reducing demulsification temperature and improving demulsification efficiency and rate.

Intertwisted superhydrophilic and superhydrophobic collagen fibers enabled anti-fouling high-performance separation of emulsion wastewater.

Oil-contaminated wastewater has been one of the most concerned environmental issues. Superwetting materials-enabled remediation of oil contamination in wastewater faces the critical challenge of fouling problems due to the formation of intercepted phase. Herein, high-performance separation of emulsions wastewater was accomplished by developing collagen fibers (CFs)-derived water-oil dual-channels that were comprised of intertwisted superhydrophilic and superhydrophobic CFs. The dual-channels relied on the superhydrophilic CFs to accomplish efficient demulsifying, which played the role as water-channel to enable fast transportation of water, while the superhydrophobic CFs served as the oil-transport channel to permit oil transportation. The mutual repellency between water-channel and oil-channel was essential to guarantee the stability of established dual-channels. The unique dual-channel separation mechanism fundamentally resolved the intercepted phase-caused fouling problem frequently engaged by the superwetting materials that provided single-channel separation capability. Long-lasting (1440 min) anti-fouling separations were achieved by the superwetting CFs-derived dual-channels with separation efficiency high up to 99.99%, and more than 4-fold of stable separation flux as compared with that of superhydrophilic CFs with single-channel separation capability. Our investigations demonstrated a novel strategy by using superwetting CFs to develop water-oil dual-channels for achieving high-performance anti-fouling separation of emulsions wastewater. ENVIRONMENTAL IMPLICATION: Industrial processes discard a large amount of emulsion wastewater, which seriously imperils the aquatic ecosystem. This work demonstrated a conceptual-new strategy to achieve effective remediation of emulsion wastewater via the water-oil dual-channels established by the intertwisted superhydrophilic and superhydrophobic collagen fibers (CFs). The superhydrophilic CFs enabled efficient demulsification of emulsions and played the role of water-channel for the rapid transportation of water, while the superhydrophobic CFs worked as oil-channel to permit the efficient transportation of oil pollutants. Consequently, the long-term (1440 min) anti-fouling high-performance separation of emulsion wastewater was achieved.

Mechanism study of aging oil demulsification and dehydration under ultrasonic irradiation.

With the tertiary oil recovery in the oilfield, the content of aging oil emulsion with high water content and complex components has become more prevalent, so it is crucial for aging oil to break the emulsification. In this paper, the experimental laws of water content are explored under the conditions of different transducer input powers through the ultrasonic reforming of aging oil, and the microscopic topography, particle size, components, etc. of oil samples before and after the irradiation of ultrasound are characterized through the microscopic analysis, particle size analysis and component analysis and other ways. The results show that the oil samples achieve the effect of demulsification and dehydration in the presence of ultrasonic cavitation effect, with a maximum dehydration rate of 98.24 %, and that the dehydration rate follows an "M-type" trend with the increase of power. The results of microscopic and particle size analyses demonstrate that ultrasonic irradiation destabilizes the oil-water interfacial membrane, and causes droplets of different sizes to collide, agglomerate, and settle. It was also observed that the droplets of the emulsion system are more evenly distributed and the intervals are increased. Furthermore, we hypothesize that ultrasound may be less irreversible in demulsification and dehydration of aging oil.

Zwitterionic Tröger's Base Microfiltration Membrane Prepared via Vapor-Induced Phase Separation with Improved Demulsification and Antifouling Performance.

The fouling of separation membranes has consistently been a primary factor contributing to the decline in membrane performance. Enhancing the surface hydrophilicity of the membrane proves to be an effective strategy in mitigating membrane fouling in water treatment processes. Zwitterionic polymers (containing an equimolar number of homogeneously distributed anionic and cationic groups on the polymer chains) have been used extensively as one of the best antifouling materials for surface modification. The conventional application of zwitterionic compounds as surface modifiers is intricate and inefficient, adding complexity and length to the membrane preparation process, particularly on an industrial scale. To overcome these limitations, zwitterionic polymer, directly used as a main material, is an effective method. In this work, a novel zwitterionic polymer (TB)-zwitterionic Tröger's base (ZTB)-was synthesized by quaternizing Tröger's base (TB) with 1,3-propane sultone. The obtained ZTB is blended with TB to fabricate microfiltration (MF) membranes via the vapor-induced phase separation (VIPS) process, offering a strategic solution for separating emulsified oily wastewater. Atomic force microscopy (AFM), scanning electron microscopy (SEM), water contact angle, and zeta potential measurements were employed to characterize the surface of ZTB/TB blended membranes, assessing surface morphology, charge, and hydrophilic/hydrophobic properties. The impact of varying ZTB levels on membrane surface morphology, hydrophilicity, water flux, and rejection were investigated. The results showed that an increase in ZTB content improved hydrophilicity and surface roughness, consequently enhancing water permeability. Due to the attraction of water vapor, the enrichment of zwitterionic segments was enriched, and a stable hydration layer was formed on the membrane surface. The hydration layer formed by zwitterions endowed the membrane with good antifouling properties. The proposed mechanism elucidates the membrane's proficiency in demulsification and the reduction in irreversible fouling through the synergistic regulation of surface charge and hydrophilicity, facilitated by electrostatic repulsion and the formation of a hydration layer. The ZTB/TB blended membranes demonstrated superior efficiency in oil-water separation, achieving a maximum flux of 1897.63 LMH bar-1 and an oil rejection rate as high as 99% in the oil-water emulsion separation process. This study reveals the migration behavior of the zwitterionic polymer in the membrane during the VIPS process. It enhances our comprehension of the antifouling mechanism of zwitterionic membranes and provides guidance for designing novel materials for antifouling membranes.

Fabrication of a poly(N-isopropylacrylamide)-grafted alginate composite aerogel for efficient treatment of emulsified oily wastewater.

The treatment of emulsion wastewater poses significant challenges. In this study, a novel porous material, namely esterified bagasse/poly(N, N-dimethylacrylamide)/sodium alginate (SBS/PDMAA/Alg) aerogel, was developed for efficient demulsification and oil recovery. By grafting a poly(N-isopropylacrylamide) (PNIPAM) brush onto the SBS/PDMAA/Alg skeleton through free radical polymerization, the resulting aerogel exhibits both surface charge and a molecular brush structure. The aerogel demonstrates remarkable demulsification efficiency for cationic surfactant-stabilized emulsions at various concentrations, achieving a demulsification efficiency of 95.6% even at an oil content of 100 g L-1. Furthermore, the molecular brush structure extends the application range of the aerogel, enabling a demulsification efficiency of 98.3% for anionic and non-ionic surfactant-stabilized emulsions. The interpenetrating polymer network (IPN) structure formed by SBS, PDMAA, and alginate enhances the mechanical stability of the aerogel, enabling a demulsification efficiency of 91.3% even after 20 repeated cycles. The demulsification ability of the composite aerogel is attributed to its surface charge, high interfacial activity, and unique brush-like structure. A demulsification mechanism based on the synergistic effect of surface charge and molecular brush is proposed to elucidate the efficient demulsification process.

Nanomagnetic Cyclodextrin decorated with ionic liquid as green and reversible Demulsifier for breaking of crude oil emulsions.

Application of the chemical demulsifiers is the best choice for breaking the water in crude oil (W/O) emulsions in the petroleum industry. Here, novel, environmentally friendly, efficient, and easily reusable Fe3O4 nanomagnetic compounds based on imidazolium-decorated cyclodextrin were successfully synthesized and applied to demulsify the water in crude oil (W/O) emulsions. At first, Fe3O4 nanoparticles were decorated with ß-cyclodextrin (ß-CD) to prepare Fe3O4@ß-CD@IL magnetic nanoparticles. Then, imidazole (Im) was separately reacted with 1-bromohexane and 1-bromodecane to prepare [Im-C6][Br] and [Im-C10][Br] ionic liquids, respectively. The prepared imidazolium-based ionic liquids were reacted with N-propyltriethoxysilane to synthesize [ImSi-C6][Br] and [ImSi-C10][Br]. Finally, [ImSi-Cn][Br] was immobilized on Fe3O4@ß-CD to obtain nanomagnetic demulsifiers. Structure of the synthesized compounds was confirmed using different methods such as FT-IR, NMR, and elemental analysis. TGA, VSM, and FESEM methods were used to investigate the thermal stability, magnetic properties, and the morphology, respectively. Fe3O4@ßCD and Fe3O4@ßCD@[ImSi-C10][Br] nanoparticles respectively showed the particle size in the range of 40-70 nm and 50-80 nm. After grafting the imidazolium-based ionic liquid on the surface of support, the magnetization number reduced from 25.6 emu/g for Fe3O4@ß-CD to 24.9 emu/g for Fe3O4@ß-CD@[ImSi-C10][Br]. Synthesized material employed to break the (10:90 and 30:70 Vol%) W/O emulsions at the concentration range of 1000-5000 ppm. The maximum demulsification efficiency (DE%) of 92 % was obtained using a Fe3O4@ß-CD@[ImSi-C10][Br] at 5000 ppm for (30:70 Vol%) W/O emulsion within 24 h. Interfacial tension (IFT) values decreased with increasing the DE%. The Fe3O4@ßCD@[ImSi-C10][Br] demulsifier was reused five times with acceptable yields. The cooperation of imidazolium and ß-CD in the green nanomagnetic demulsifiers led to the efficient demulsification of the W/O emulsions. The preparation of different ionic liquids or changing the counter anions are our potential future directions for this research. Demulsification at high demulsifier concentration can be considered a limitation of the nanomagnetic cyclodextrin decorated with ionic liquid. But due to the low amount of ionic liquid immobilized in the synthesized demulsifier, the cost of the final demulsifier is lower that other demulsifiers with full ionic liquid backbones, which increases its potential for industrial applications.

Pretreatment of alkali/surfactant/polymer (ASP)-flooding produced wastewater by electron beam radiation to improve oil-water separation.

The management of wastewater produced from alkali/surfactant/polymer (ASP) flooding, known for its considerable volume and high emulsion stability, poses a challenge in oilfields globally. This study has demonstrated that ionizing irradiation is a promising pretreatment method for ASP wastewater to improve oil-water separation. After a settling time of 1 h, approximately 69.5% of oil remained in the raw ASP wastewater, while only 20-29% of the oil persisted in the liquid phase following radiation at absorbed doses ranging from 0.1 to 5.0 kGy. A noticeable increase in the size of oil droplets and reduction in turbidity was observed after irradiation. Further analysis revealed that the combination of surfactant, sodium dodecyl sulfate (SDS) and alkali exhibits a synergistic impact, leading to a substantial reduction in interface tension of ASP wastewater. Notably, ionizing irradiation induces several key changes that are crucial for efficient demulsification. The transformation of the wastewater's rheological behavior from pseudoplastics to a Newtonian fluid accompanied by a reduction in viscosity, the increased interfacial tension at both liquid-air and liquid-oil interfaces, along with the degradation of organic components such as partly hydrolyzed polyacrylamide (HPAM) and SDS, all contribute to the coalescence and floatation of oil droplets.

Advances in ultrasonic treatment of oily sludge: mechanisms, industrial applications, and integration with combined treatment technologies.

In the petroleum sector, the generation of oily sludge is an unavoidable byproduct, necessitating the development of efficient treatment strategies for both economic gain and the mitigation of negative environmental impacts. The intricate composition of oily sludge poses a formidable challenge, as existing treatment methodologies frequently fall short of achieving baseline disposal criteria. The processes of demulsification and dehydration are integral to diminishing the oil content and reclaiming valuable crude oil, thereby playing a critical role in the management of oily sludge. Among the myriad of treatment solutions, ultrasonic technology has emerged as a particularly effective physical method, celebrated for its diverse applications and lack of resultant secondary pollution. This comprehensive review delves into the underlying mechanisms and recent progress in the ultrasonic treatment of oily sludge, with a specific focus on its industrial implementations within China. Both isolated ultrasonic treatment and its combination with other technological approaches have proven successful in addressing oily sludge challenges. The adoption of industrial-scale systems that amalgamate ultrasound with multi-technological processes has shown marked enhancements in treatment efficacy. The fusion of ultrasonic technology with other cutting-edge methods holds considerable potential across a spectrum of applications. To fulfill the goals of resource recovery, reduction, and neutralization in oily sludge management, the industrial adoption and adept application of a variety of treatment technologies are imperative.

Synthesis and application of recyclable magnetic cellulose nanocrystals for effective demulsification of water in crude oil emulsions.

The development of eco-friendly, efficient, and economical demulsifiers for the demulsification of water in crude oil emulsion is one of the important issues in the petroleum industry. Demulsifiers with suitable performance in several demulsification methods are good choices for effective and economical demulsification. In this study, recyclable magnetic cellulose nanocrystals have been synthesized from cotton by a simple method and used in the demulsification of water in crude oil emulsions. Chemical and magnetic demulsification by magnetic cellulose nanocrystals has been investigated. In addition, the effects of time, temperature, and demulsifier concentration on the demulsification efficiency have been evaluated. According to the results, this demulsifier can be used as an effective demulsifier for both chemical and magnetic demulsification and displayed a demulsification efficiency of 100 % at 50 °C without a magnet and 90 % at 20 °C with a magnet. The chemical demulsification efficiency of Fe3O4 nanoparticles was investigated and it showed lower DE compared to magnetic cellulose nanocrystals. The recyclability tests of the demulsifier indicated that magnetic cellulose nanocrystals can be used up to 4 times. Finally, the demulsification mechanism and interfacial tension measurements revealed that this demulsifier reduced the interfacial tension between water and crude oil and increased the water droplet sizes.

Determination of chiral prothioconazole and its chiral metabolite in water, juice, tea, and vinegar using emulsive liquid-liquid microextraction combined with ultra-high performance liquid chromatography.

Emulsive liquid-liquid microextraction (ELLME), a simple, rapid, and environmentally friendly technique, was established to identify chiral prothioconazole and its chiral metabolite in water, juice, tea, and vinegar using ultra-high-performance liquid chromatography (UPLC). Environmentally friendly extractant was mixed with pure water to prepare a high-concentration emulsion, which was added to samples to complete the emulsification and extraction in 1 s. Afterward, an electrolyte solution was added to complete the demulsification without centrifugation. ELLME did not use dispersants compared to the familiar dispersive liquid-liquid microextraction (DLLME), thus reducing the use of toxic solvents and avoiding the effect of dispersants on the partition coefficient. The linear range was from 0.01 to 1 mg/L. The limit of detection was 0.003 mg/L. The extraction recoveries ranged from 82.4 % to 101.6 %, with relative standard deviations of 0.7-5.2 %. The ELLME method developed has the potential to serve as an alternative to DLLME.

Preparation and evaluation of hydroxyethyl cellulose-based functional polymer for highly efficient utilization of heavy oil under the harsh reservoir environments.

Emulsification viscosity reduction and subsequent demulsification are effective strategies to improve the utilization rate of heavy oil. However, traditional surfactants are challenged by unsatisfactory salt tolerance, inadequate stability in emulsification, difficulty in demulsification and pollution problem of oily wastewater discharge. To realize the feasibility and environment-friendliness of heavy oil utilization in the harsh reservoir environments, we designed a functional polymer and conducted a comprehensive evaluation using heavy oil samples from Chenping oil well in Shengli Oilfield. It was synthesized by grafting two hydrophobic monomers, lauryl methacrylate (LMA) and N, N-Diethylaminomethyl methacrylate (DEAEMA), onto the hydrophilia hydroxyethyl cellulose (HEC) by free-radical polymerization. The viscosity reduction rate can reach 99.57 % even under the high salinity of 26,050 mg/L. The stable oil-in-water (O/W) emulsion can be maintained for >48 h, satisfying the actual requirements for heavy oil recovery. Moreover, the emulsion can be completely demulsified in a CO2 atmosphere within 30 min, suggesting its satisfactory demulsification performance. Our study achieved the one-step transformation of heavy oil emulsion between emulsification and demulsification, which provides a green bio-based material and an ingenious strategy for enhanced oil recovery and other chemical engineering applications including oil/water separation.

Synthesis and Application of a Novel Multi-Branched Block Polyether Low-Temperature Demulsifier.

In this paper, a low-temperature thick oil demulsifier with high polarity was prepared by introducing ethylene oxide, propylene oxide block, and butylene oxide using m-diphenol as a starting agent. The main reasons for the difficulty involved in the low-temperature emulsification of extractive fluids were explained by analyzing the synthetic influencing factors and infrared spectra of the star comb polymer (PR-D2) and by analyzing the four fractions, interfacial energies, and zeta potentials of crude oils from the Chun and Gao fields. The effects of PR-D2 surfactant on the emulsification performance of crude oil recovery fluids were investigated via indoor and field experiments. The experimental results indicate that the optimal synthesis conditions for this emulsion breaker are as follows: a quality ratio of ionic reaction intermediates and meso-diphenol of R = 10:1; 1 g of the initiator; a polymerization temperature of 80 °C; and a reaction time of 8 h. Colloidal asphaltenes in the crude oil were the main factor hindering the low-temperature demulsification of the Gao oilfield's extractive fluids, and the reason for the demulsification difficulty of the extractive fluids in the Chun oilfield is that the temperature of demulsification is lower than the wax precipitation point. The demulsification rate of the Chun oilfield's extractive fluids reached more than 98% when the PR-D2 concentration reached 150 mg/L at 43 °C. The demulsification rate of the Gao oilfield's extractive fluids reached more than 98% at a PR-D2 concentration of 150 mg/L at 65 °C. The field experiments show that the Chun oilfield's extractive fluids can still demulsify after the temperature is reduced to 43 °C in winter. The emulsification temperature of the Gao oilfield's extractive fluids was reduced from 73 °C to 68 °C, with an excellent demulsification effect.

Efficient Demulsification Performance of Emulsified Condensate Oil by Hyperbranched Low-Temperature Demulsifiers.

Focusing on the problem of poor demulsification performance of light crude oil emulsions in low-permeability oilfields at low temperatures, the composition of the emulsion samples, clay particle size distribution, and the viscosity-temperature relationship curve of samples were analyzed. Based on the results of emulsion composition analysis and characteristics, the bottle test method was used to analyze the demulsifying effect of different commercial types of demulsifiers, revealing the demulsification mechanism. The field tests confirm the demulsification capabilities of Polyoxyethylene polyoxypropylene quaternized polyoxyolefins surfactants (PR demulsifiers). The results reveal that PR demulsifiers combine the features of decreasing the interfacial tension between oil and water and adsorbing SiO2, allowing for quick demulsification and flocculation at low temperatures. This research serves as a theoretical and practical foundation for the study and advancement of low-temperature demulsification technology in oilfields.