RESUMO
Massive exudates oversecreted from burn wounds always delay the healing process, accompanied by undesired adhesion, continuous inflammation, and high infection risk. Conventional dressings with limited draining ability cannot effectively remove the excessive exudates but constrain them in the wetted dressings immersing the wound bed. Herein, we fabricate an enhanced fractal self-pumping dressing by floating and accumulating hollow glass microspheres in the hydrogel precursor, that can continuously drain water at a non-declining high speed and effectively promote burn wound healing. Small hollow glass microspheres can split the fractal microchannels into smaller ones with higher fractal dimensions, resulting in higher absorption efficiency. In an in vivo burn wound model on the dorsum of murine, the enhanced fractal self-pumping dressing can significantly reduce the appearance of the wound area and alleviate tissue edema along the healing process. This study sheds light on designing high-efficiency and continuous-draining dressings for clinical applications.
RESUMO
The feature of low-density and thermal insulation properties of polydimethylsiloxane (PDMS) foam is one of the important challenges of the silicone industry seeking to make these products more competitive compared to traditional polymer foams. Herein, we report a green, simple, and low-cost strategy for synthesizing ultra-low-density porous silicone composite materials via Si-H cross-linking and foaming chemistry, and the sialylation-modified hollow glass microspheres (m-HM) were used to promote the HM/PDMS compatibility. Typically, the presence of 7.5 wt% m-HM decreases the density of pure foam from 135 mg/cm-3 to 104 mg/cm-3 without affecting the foaming reaction between Si-H and Si-OH and produces a stable porous structure. The optimized m-HM-modified PDMS foam composites showed excellent mechanical flexibility (unchanged maximum stress values at a strain of 70% after 100 compressive cycles) and good thermal insulation (from 150.0 °C to 52.1 °C for the sample with ~20 mm thickness). Our results suggest that the use of hollow microparticles is an effective strategy for fabricating lightweight, mechanically flexible, and thermal insulation PDMS foam composite materials for many potential applications.
RESUMO
The composite rubber reinforced with hollow glass microsphere (HGM) was a promising composite material for noise reduction, and its sound insulation mechanism was studied based on an acoustic finite element simulation to gain the appropriate parameter with certain constraint conditions. The built simulation model included the air domain, polymer domain and inorganic particles domain. The sound insulation mechanism of the composite material was investigated through distributions of the sound pressure and sound pressure level. The influences of the parameters on the sound transmission loss (STL) were researched one by one, such as the densities of the composite rubber and HGM, the acoustic velocities in the polymer and inorganic particle, the frequency of the incident wave, the thickness of the sound insulator, and the diameter, volume ratio and hollow ratio of the HGM. The weighted STL with the 1/3 octave band was treated as the evaluation criterion to compare the sound insulation property with the various parameters. For the limited thicknesses of 1 mm, 2 mm, 3 mm and 4 mm, the corresponding optimal weighted STL of the composite material reached 14.02 dB, 19.88 dB, 22.838 dB and 25.27 dB with the selected parameters, which exhibited an excellent sound insulation performance and could promote the practical applications of the proposed composite rubber reinforced with HGM.
RESUMO
Coagulation-flocculation in industrial wastewater treatment drives environmental pollution from landfilling heavy metal-laden sludge. Efficient separation of the sludge is crucial for cost-effective metal recovery. This study explored a new separation method of Cu2+, Ni2+, Zn2+ and Cr3+ via self-floating metal hydroxides assisted by hollow glass microsphere (HGM) carriers. The amount of OH- was stoichiometric to the positive charges of metal ions, mixed with 1 mg mL-1 HGM, causing metal hydroxides to attach to HGM surface via heterogeneous nucleation. The self-floating system removed 37.5% and 14.0% more metals than sedimentation at 50 and 200 mg L-1 metal concentrations. HGM additions increased the particle size of metal hydroxides by up to 12.5 times to that of HGM at 18.8 ± 1.1 µm, benefiting their solid-liquid separation. By pumping the wastewater downward in column reactor at velocities equal to or less than the self-floating sludge, 96.4% metals were removed in continuous flow. The recovery rates of HGM and metals reached 92.0 ± 2.2% and 92.7 ± 3.2%, and the concentration of the recovered metal reached 19,339 ± 394 mg L-1 for potential reutilization in industrial electroplating. This research investigated a new separation strategy based on solid self-flotation for sustainable treatment of metal-laden wastewater.
RESUMO
Infrared thermal reflective coating is an effective material to reduce building energy consumption and carbon emission. In this work, needle-shaped-rutile-shell-coated hollow glass microbeads (HGM) were prepared by surface modification of HGM and thermohydrolysis of TiCl4, and the possible shell formation mechanism was also proposed. The near infrared (NIR) reflectance of the coated HGM reached 93.3%, which could be further increased to 97.3% after the rutile shell crystallinity was improved by heat treatment. Furthermore, HGM/styrene-acrylic composite reflective coating was prepared on the surface of gypsum board by facile blending and coating methods, and the thermal insulation performance was measured by an indigenously designed experimental heat set-up. The results show that the composite coating prepared by HGM coated with rutile shell shows better NIR reflectance and thermal insulation performance than that prepared by pure organic coating and uncoated HGM. Meanwhile, it also shows better surface hydrophobicity, which is conducive to long-term and stable infrared reflection performance.
RESUMO
High-performance composites with a resin matrix are urgently required for electronic packaging due to their low dielectric constant, outstanding high temperature resistance, excellent corrosion resistance, light weight and easy molding. In this work, hollow-glass-microsphere (HGM)-filled fluorinated-phthalonitrile (PBDP) composites, with filler contents ranging from 0 to 35.0 vol.%, were prepared in order to modify the dielectric properties of the phthalonitrile. Scanning electron microscopy (SEM) observations indicate that the modified HGM particles were uniformly dispersed in the matrix. The PBDP/27.5HGM-NH2 composite demonstrates a low dielectric constant of 1.85 at 12 GHz. The 5% thermogravimetric temperature (T5) of composites with silanized HGM filler (481-486 °C) is higher than the minimum packaging-material requirements (450 °C). In addition, the heat-resistance index (THRI) of PBDP/HGM-NH2 composites reached as high as 268 °C. the storage modulus of PBDP/HGM-NH2 composites were significantly increased to 1283 MPa at 400 °C, an increase by 50%, in comparison to that of PBDP phthalonitrile resin (857 MPa). The excellent dielectric and thermal properties of the present composites may pave a way for comprehensive applications in electronic packaging and thermal management for energy systems.
RESUMO
The hollow glass microsphere (HGM) containing polymer materials, which are named as syntactic foams, have been applied as lightweight materials in various fields. In this study, carboxyl group-containing hyperbranched polymer (HBP) was added to a glass fiber (GF)-reinforced syntactic foam (RSF) composite for the simultaneous enhancement of mechanical and rheological properties. HBP was mixed in various concentrations (0.5-2.0 phr) with RSF, which contains 23 wt% of HGM and 5 wt% of GF, and the rheological, thermal, and mechanical properties were characterized systematically. As a result of the lubricating effect of the HBP molecule, which comes from its dendritic architecture, the viscosity, storage modulus, loss modulus, and the shear stress of the composite decreased as the HBP content increased. At the same time, because of the hydrogen bonding among the polymer, filler, and HBP, the compatibility between filler and the polymer matrix was enhanced. As a result, by adding a small amount (0.5-2.0 phr) of HBP to the RSF composite, the tensile strength and flexural modulus were increased by 24.3 and 9.7%, respectively, and the specific gravity of the composite was decreased from 0.948 to 0.917. With these simultaneous effects on the polymer composite, HBP could be potentially utilized further in the field of lightweight materials.
RESUMO
Microbubbles are widely used in medical ultrasound imaging and drug delivery. Many studies have attempted to quantify the collapse pressure of microbubbles using methods that vary depending on the type and population of bubbles and the frequency band of the ultrasound. However, accurate measurement of collapse pressure is difficult as a result of non-acoustic pressure factors generated by physical and chemical reactions such as dissolution, cavitation, and interaction between bubbles. In this study, we developed a method for accurately measuring collapse pressure using only ultrasound pulse acoustic pressure. Under the proposed method, the collapse pressure of a single hollow glass microsphere (HGM) is measured using a high-frequency (20-40 MHz) single-beam acoustic tweezer (SBAT), thereby eliminating the influence of additional factors. Based on these measurements, the collapse pressure is derived as a function of the HGM size using the microspheres' true density. We also developed a method for estimating high-frequency acoustic pressure, whose measurement using current hydrophone equipment is complicated by limitations in the size of the active aperture. By recording the transmit voltage at the moment of collapse and referencing it against the corresponding pressure, it is possible to estimate the acoustic pressure at the given transmit condition. These results of this study suggest a method for quantifying high-frequency acoustic pressure, provide a potential reference for the characterization of bubble collapse pressure, and demonstrate the potential use of acoustic tweezers as a tool for measuring the elastic properties of particles/cells.
RESUMO
Glass fiber fabrics/hollow glass microspheres (HGM)-waterborne polyurethane (WPU) textile composites were prepared using glass fiber, WPU, and HGM as skeleton material, binder, and insulation filler, respectively, to study the effect of HGM on the thermal insulation performance of glass fiber fabrics. Scanning electron microscopy, Instron 3367 tensile test instrument, thermal constant analysis, and infrared thermal imaging were used to determine the cross-sectional morphology, mechanical property, thermal conductivity, and thermal insulation property, respectively, of the developed materials. The results show that the addition of HGM mixed in WPU significantly enhanced thermal insulation performance of the textile composite with the reduction of thermal conductivity of 45.2% when the volume ratio of HGM to WPU is 0.8 compared with that of material without HGM. The composite can achieve the thermal insulation effect with a temperature difference of 17.74 °C at the temperature field of 70 °C. Meanwhile, the tensile strength of the composite is improved from 14.16 to 22.14 MPa. With these results, it is confirmed that designing hollow glass microspheres (HGM) is an effective way to develop and enhance the high performance of insulation materials with an obvious lightweight of the bulk density reaching about 50%.
RESUMO
In this study, a new class of thermal insulation composites was prepared by blending a modified hollow glass microsphere (HGM) with furan resin. The particle dispersion between the microparticles and resin matrix was improved using 3-methacryloxypropyltrimethoxy silane (KH-570). Furthermore, the structure and morphology of the modified HGM were characterised by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). In addition, the effects of the modified HGM on the thermal insulation, flame retardancy, and thermal properties of the composites were investigated. The thermal conductivity of the composites was lower than that of the native furan resin. The minimum thermal conductivity of the composites was 0.0274 W/m·K; the flame retardancy of the composites improved, and the limiting oxygen index become a maximum of 31.6%, reaching the refractory material level. Furthermore, the thermal analysis of the composites demonstrated enhanced thermal stability. This study demonstrates that the composite material exhibited good thermal insulation performance and flame retardancy and that it can be applied in the field of thermal insulation.
RESUMO
In this study, iron-based metal matrix syntactic foam (MMSF) containing hollow glass microspheres as filler was investigated with respect to notch sensitivity aspects. The MMSF was produced by means of metal powder injection molding. The notch sensitivity was studied via (i) elastic-plastic fracture mechanics measurements (determination of R-curves based on three-point bending tests) and (ii) Charpy impact tests. In both cases, the samples were machined with two different (U- and V-shaped) notch geometries. The critical J-integral value was determined for both notch types, which resulted in lower fracture toughness values in the case of the V-shaped notches and thus notch sensitivity of the material. This finding can be connected to the characteristics of the deformation zone and the associated stress concentration at the tip of the machined notches. The results were confirmed by Charpy impact tests showing ~30% higher impact energy in the case of the U-shaped notch. The failure modes were investigated by means of scanning electron microscopy. In contrast to the bulk material, the MMSF showed brittle fracture behavior.
RESUMO
Rapid, high-efficient adsorbents with efficient solid-liquid separation ability has broad application prospects in the treatment of dye wastewater. In this study, polydopamine and methacryloyloxyethyltrimethyl ammonium chloride were grafted onto hollow glass microspheres to prepare the enhanced polydopamine shell structure adsorbent with self-floating ability. Furthermore, the adsorbent achieves high-efficiency surface solid-liquid separation, which overcomes the disadvantages of the traditional separation methods. Characterizations of the as-synthesized microspheres were performed using various techniques such as SEM, EDS, BET, XPS, FT-IR, TGA and XRD. The adsorbent achieved rapid and high-efficient adsorption of alizarin cyanine green F via the interactions of electrostatic attracting and π-π stacking, and under the optimal experimental conditions, the removal efficiency of 0.10â¯m mol L-1 dye solution reaches 94.51%, and the adsorption process reaches equilibrium within 60â¯min. Adsorption isotherms and kinetics data of the adsorbent were well fitted by Langmuir isotherm and pseudo-second-order kinetic models, respectively. The as-synthesized adsorbent has excellent recyclability, and its adsorption performance can be maintained after 5 cycles of reuse. The self-floating adsorbent has great potential for the removal of dissolved contaminants and cost-effective separation.
RESUMO
In this study, our group grafted 2-acrylamido-2-methylpropane sulfonic acid (AMPS) onto the surface of hollow glass microspheres (HGM) and successfully prepared AMPS grafted floating adsorbent (AFA). The prepared AFA carries a large amount of negative charges, and the adsorptions of cationic dyes are achieved under the action of strong electrostatic interaction. Furthermore, due to the unique shell structure of AFA, it has a stable self-floating ability, which may change the traditional separation method to make the adsorbent easier to enrich and separate from water surface. Characterizations of AFA by scanning electron microscope, energy dispersive spectrometry, X-ray photoelectron spectroscopy. Fourier transform infrared spectra, Brunauer-Emmett-Teller surface areas, thermogravimetric analysis, and X-ray diffractometer shows the successful grafting of AMPS. Adsorption experiments confirmed that the adsorption capacities of AFA for methylene blue, malachite green, basic fuchsin and crystal violet under optimum conditions were 436.8 mg g-1, 637.6 mg g-1, 457.8 mg g-1, and 399.4 mg g-1, respectively. At the same time, AFA has excellent recyclability, and its adsorption capacity can be maintained after 6 cycles of reuse.
RESUMO
Many researchers have studied the miniaturization of the hemisphere resonator gyroscope for decades. The hemisphere resonator (HSR), as the core component, has a size that has been reduced to the submillimeter level. We developed a method of batch production of micro-hemisphere shell resonators based on a glass-blowing process to obtain larger hemisphere shells with a higher ratio of height to diameter (H/D), we introduced the chemical foaming process (CFP) and acquired an optimized hemisphere shell; the contrasted and improved H/D of the hemisphere shell are 0.61 and 0.80, respectively. Finally, we increased the volume of glass shell resonator by 51.48 times while decreasing the four-node wineglass resonant frequencies from 7.24 MHz to 0.98 MHz. The larger HSR with greater surface area is helpful for setting larger surrounding drive and sense capacitive electrodes, thereby enhancing the sensitivity of HSR to the rotation. This CFP method not only provides more convenience to control the shape of a hemisphere shell but also reduces non-negligible cost in the fabrication process. In addition, this method may inspire some other research fields, e.g., microfluidics, chemical analysis, and wafer level package (WLP).
RESUMO
HYPOTHESIS: Organic foamy materials possess good thermal insulation properties and inorganic materials are non-combustible. Hence, it is possible to develop a kind of organic-inorganic lightweight thermal insulation materials with excellent fire safety. EXPERIMENTS: Hollow glass microsphere (HGM), as one kind of lightweight noncombustible inorganic material, was chosen as the filling material. Phenolic resin (PR), as the flame retardant polymeric material, was used as binding material. A series of HGM/PR composites with various PR/HGM mass ratio were prepared. Properties, such as apparent density, microstructure, mechanical strength, thermal conductivity, burning behavior and flame retardancy of the specimens were determined, respectively. FINDINGS: The results show that the surface of HGM particles is coated by a layer of cured PR and the HGM powder is glued together firmly from the scanning electron microscope (SEM) images. With the increase of PR/HGM mass ratio, both of apparent density and mechanical strength of HGM/PR composites increase, but thermal conductivity and limiting oxygen index (LOI) values decrease, all of the specimens still possess high LOI value (>50%). What's more, no flaming combustion (merely partial carbonization) and hardly any smoke can be observed during the burning process, which indicates the HGM/PR composites possess excellent flame retardant property and fire safety.
RESUMO
Tiny hollow glass microsphere (HGM) can be applied for designing new light-weighted and thermal-insulated composites as high strength core, owing to its hollow structure. However, little work has been found for studying its own overall thermal conductivity independent of any matrix, which generally cannot be measured or evaluated directly. In this study, the overall thermal conductivity of HGM is investigated experimentally and numerically. The experimental investigation of thermal conductivity of HGM powder is performed by the transient plane source (TPS) technique to provide a reference to numerical results, which are obtained by a developed three-dimensional two-step hierarchical computational method. In the present method, three heterogeneous HGM stacking elements representing different distributions of HGMs in the powder are assumed. Each stacking element and its equivalent homogeneous solid counterpart are, respectively, embedded into a fictitious matrix material as fillers to form two equivalent composite systems at different levels, and then the overall thermal conductivity of each stacking element can be numerically determined through the equivalence of the two systems. The comparison of experimental and computational results indicates the present computational modeling can be used for effectively predicting the overall thermal conductivity of single HGM and its powder in a flexible way. Besides, it is necessary to note that the influence of thermal interfacial resistance cannot be removed from the experimental results in the TPS measurement.
RESUMO
Nowadays, reducing the fire hazard of thermoplastic polyurethane (TPU) is an important research direction in the fields of fire safety materials. In this article, hollow glass microsphere (HGM) was used to reduce the fire hazard of TPU in combustion process. The fire characteristics including smoke and heat production of TPU composites were evaluated using smoke density test (SDT) and cone calorimeter test (CCT). And the thermal decomposition and flammable properties were further studied using thermogravimetric analysis/infrared spectrometry (TG-IR) and limiting oxygen index (LOI), etc. The SDT results showed that the luminous flux (LF) of TPU4 containing 2.00wt% HGM was up to 24% at the end of test without flame, which is much higher than that of TPU0 (5%). And, the CCT results indicated that 2.00wt% HGM could make the total smoke release (TSR) decrease from 1019m2/m2 (TPU0) to 757m2/m2 (TPU4), reduced by 26%. The TG-IR results confirmed that HGM could improve the thermal stability of composites and reduce the production of some toxic gases. The above results illustrated HGM had a good prospect in reducing the fire hazard for TPU.