In-situ strategies for melamine-functionalized graphene oxide nanosheets-based nanocomposite proton exchange membranes in wide-temperature range applications.

The traditional preparation of nanocomposite proton exchange membranes (PEM) is hindered by poor organic-inorganic interface compatibility, insufficient proton-conducting sites, easy aggregation of nanoparticles, and difficulty in leveraging nanoscale advantages. In this study, a novel method involving electrochemical anodic oxidation exfoliation was employed to prepare melamine-coated graphene oxide (Me@GO), which was subsequently subjected to in-situ polymerization with poly(2,5-benzimidazole) (ABPBI) to prepare a Me@GO/ABPBI composite proton exchange membrane. Benefiting from the strong hydrogen bonding and large π stacking interactions, melamine (Me) tightly bound to graphene oxide (GO), effectively preventing the secondary aggregation of GO after exfoliation. Moreover, the abundant alkaline functional groups of melamine enhanced the enhancement of phosphoric acid (PA) retention in the Me@GO/ABPBI membranes, thereby increasing the number of proton-conducting sites. The experimental results indicated that the introduction of Me@GO enhanced membrane properties. For Me@GO at a concentration of 1 wt%, the tensile strength of the 1Me@GO/ABPBI composite membrane reached 207 MPa, nearly 2.52 times that of the pure membrane. The proton conductivity of the 1Me@GO/ABPBI composite membrane reached 0.01 S cm-1 across a wide temperature range (40-180 °C), peaking at 0.087 S cm-1 at 180 °C. Additionally, a single-cell incorporating the 1Me@GO/ABPBI composite membrane achieved a peak power density of 0.304 W cm-2 at 160 °C, nearly 1.46 times that of the pure membrane. Benefiting from the well-dispersed and PA-enriched proton channels provided by Me@GO, the Me@GO/ABPBI composite membrane exhibits excellent prospects for wide-temperature range (40-180 °C) applications.

Trimetallic-doped carbon nitride achieves chondroitin sulfate degradation via a free radical degradation strategy.

Traditional Fenton principles for degrading polysaccharides, including chondroitin sulfate (CS), are fraught with limitations, such as strict pH-dependence, higher temperature requirements, desulfurization, and environmentally perilous. In this study, an effective Fenton-like system comprising trimetallic-doped carbon nitride material (tri-CN) with hydrogen-bonded melamine-cyanuric acid (MCA) supramolecular aggregates as its basic skeleton was engineered to overcome the challenges of traditional methods. Detailed material characterizations revealed that, compared to monometallic-doped or bimetallic-doped counterparts, tri-CN offered a larger surface area, higher porosity, and increased metal loading, thereby enhancing reactant accessibility and polysaccharide degradation efficiency. The characterization and activity assessment of the degraded polysaccharide revealed structurally intact products without significant desulfurization, indicating the effectiveness of the designed approach. Moreover, the degraded chondroitin sulfate CS3 catalyzed by tri-CN, exhibited promising antioxidant activity and anti-CRISPR potential. The results elucidated that the high-valent iron species in the material served as primary active sites, catalyzing the cleavage of hydrogen peroxide to generate hydroxyl radicals that subsequently attacked CS chains, leading to their fragmentation. Hence, the designed material can be efficiently applied to polysaccharide degradation, but not limited to photocatalysis, electrocatalysis, sensor, energy storage materials, and wastewater treatment.

Highly sensitive SERS detection of melamine based on 3D Ag@porous silicon photonic crystal.

The stability, reproducibility and engineering of SERS substrate faces a great challenge in melamine SERS assay. In this work, a simple, highly sensitive, stable and cost-efficient SERS detection platform for melamine was established based on its Raman fingerprints spectrum. The Ag@ porous silicon photonic crystal (Ag@PPC) was prepared as the 3D SERS substrate by electrochemical etching and magnetron sputter technology. The main influence factors for the preparation of SERS substrate were investigated in detail. The analytical enhancement factor of the 3D SERS substrate can reach to 2.6 × 108. The 3D SERS detection platform showed a wide linear detection range of 10-4∼10 mg L-1 and a low limit of detection of 0.1 µg L-1 for melamine. Moreover, such detection platform showed good stability, high reproducibility and high recovery rates for melamine. The 3D Ag@PPC SERS substrate can be easily prepared and engineered, displaying a great potential application in food safety field.

Improving the fire-retardant performance of industrial reactive coatings for steel building structures.

The main aim of this study was to determine key factors that regulate fire-retardant effectiveness of intumescent coatings comprising of ammonium polyphosphate, melamine, pentaerythritol, polymer binder. Fulfillment of the research objectives resulted in the development of a coating with R120 fire resistance. The expected service life of the coating is at least 15 years when applied at Z2 type of environmental conditions (indoor use). It was established that in order to provide fire resistance of around R30 it is advisable to use the styrene-acrylic polymers as binders for both water-based and organic-based intumescent systems. The ratio of target components ammonium polyphosphate/melamine/pentaerythritol in such systems should be close to 2/1/1. The coating thickness is to be 0.4-0.5 mm. To achieve higher fire resistance (R60 or more) the coating should include a vinyl acetate derivative as a binder (copolymers with ethylene or vinylversatate). Target components ratio in this case is to be close to 3.5/1/1.5, while the coating thickness should be kept at 1.6-1.8 mm. If the required class of fire resistance is above R120, coating thickness is usually to be kept above 3.5 mm. In order to achieve higher fire resistance, it is advisable to use nano-clay additives and reinforcing fibers in intumescent compositions. The obtained results were used in the development of intumescent coating, which is produced industrially and provides over R120 fire resistance of steel, which was confirmed in standardized full-scale fire tests.

A method validation of determination of melamine in marketed infant formula and milk powder of Iran.

Melamine is a recognized food contaminant that can arise incidentally or intentionally in specific categories of food. This study aimed to validate the melamine detection and quantification in infant formula and milk powders and also analyzed 40 samples consist of infant formula and milk powders from commercially available food products, from different geographic regions of Iran. The approximate content of melamine in samples was measured by High-performance liquid chromatography-ultra violet (HPLC-UV) system. A calibration curve (R2 = 0.9925) was established for detection of melamine in the range of 0.1-1.2 µg mL-1. Limit of quantification and limit of detection were 1 µg mL-1 and 3 µg mL-1, respectively. The presence of melamine in infant formula and milk powdered was investigated and it was observed that the amount of melamine in samples of infant formulas and milk powders was 0.001-0.095 mg kg-1 and 0.001-0.004 mg kg-1, respectively. These values were found to be within the prescribed limits by the European Union and Codex Alimentarius Commission legislation. It is important to note that the consumption of these dairy products, which contain low content of melamine, does not pose any significant threat to consumer health. Furthermore, the results of the risk assessment confirmed this issue.

Synthesis of silver nanoparticles embedded into melamine polyaminal networks as antibacterial and anticancer active agents.

Silver nanoparticles were successfully incorporated into a melamine-based polymer, resulting in the synthesis of (Ag NPs@Bipy-PAN) through a reverse double solvent approach. The synthesised Ag NPs@Bipy-PAN polymer underwent extensive characterisation through Powder X-ray Diffraction (PXRD), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy and Energy Dispersive X-ray (EDX) and Thermal Gravimetric Analysis. PXRD analysis confirmed the successful encapsulation of Ag nanoparticles and provided insights into the amorphous nature of the polymer following encapsulation. SEM and EDX analyses further corroborated the presence and distribution of Ag nanoparticles on the polymer surface. The biological efficacy of the Ag NPs@Bipy-PAN polymer was evaluated through antibacterial, anti-breast cancer, and biocompatibility assays. The results demonstrated notable antibacterial and anticancer activities, with significant efficacy against bacterial strains and breast cancer cells. Biocompatibility assessments indicated acceptable compatibility, particularly at a concentration of 2.5 mg/mL, compared to untreated control cells. These findings suggest that Ag NPs@Bipy-PAN has considerable potential as a candidate for cancer-targeted and antimicrobial drug delivery systems. The incorporation of silver nanoparticles into the melamine-based polymer enhances the safety profile of these systems in in vivo conditions, making them a viable option for advanced therapeutic applications.

Ultrasensitive detection of contaminants in milk using a novel NMS-Ag modified water-resistant paper substrate.

Rapid and precise detection of harmful substances in food products is essential for ensuring public health and safety. This study introduces a novel surface-enhanced Raman spectroscopy (SERS) substrate, composed of a molybdenum disulfide­silver nanocomposite, applied to flexible, water-resistant filter paper for detecting melamine and bisphenol A (BPA) in milk. Optimized molybdenum disulfide (NMS) nanoflowers (NFs) were synthesized through hydrothermal methods and high-temperature annealing, then modified with silver (Ag) nanoparticles to form the NMS-Ag nanocomposite (NMSA6). This substrate greatly enhances the Raman signal, achieving an enhancement factor of approximately 1.49 × 107 and a detection limit as low as 10-11 M for simultaneous multi-component analysis. Finite-difference time-domain (FDTD) simulations confirm the enhancement mechanism. The NMSA6 substrate demonstrates remarkably low detection limits for BPA and melamine, facilitating the analysis of various hazardous substances. These findings highlight the substrate's potential for highly sensitive, label-free detection, presenting a viable tool for food safety monitoring.

Facile synthesis of Ag NPs@MgO nanosheets for quantitative SERS-based detection and removal of hazardous organic pollutants.

Surface-enhanced Raman spectroscopy (SERS) is a highly precise and non-invasive analytical method known for its ability to detect vibrational signatures of minute analytes with exceptional sensitivity. However, the efficacy of SERS is subject to substrate properties, and current methodologies face challenges in attaining consistent, replicable, and stable substrates to regulate plasma hot spots across a wide spectral range. This study introduces a straightforward and economical approach that incorporates monodispersed silver nanoparticles onto 2-D porous magnesium oxide nanosheets (Ag@MgO-NSs) through an in-situ process. The resulting nanocomposite, Ag@MgO-NSs, demonstrates substantial SERS enhancement owing to its distinctive plasmonic resonance. The effectiveness of this nanocomposite is exemplified by depositing diverse environmental pollutants as analytes, such as antibiotic ciprofloxacin (CIP), organic dyes like rhodamine 6G (R6G) and methylene blue (MB), and nitrogen-rich pollutant like melamine (MLN), onto the proposed substrate. The proposed nanocomposite features a 2-D porous structure, resulting in a larger surface area and consequently providing numerous adsorption sites for analytes. Moreover, engineering the active sites of the nanocomposite results in a higher number of hotspots, leading to an enhanced performance. The nanocomposite outperforms, exhibiting superior detection capabilities for R6G, MB, and MLN at concentrations of 10-6 M and CIP at concentration of 10-5 M, with impressive uniformity, reproducibility, stability, and analytical enhancement factors (EF) of 6.3 x 104, 2 x 104, 2.73 x 104 and 1.8 x 104 respectively. This approach provides a direct and cost-effective method for the detection of a broad spectrum of environmental pollutants and food additives, presenting potential applications across diverse domains. The detected environmental pollutants and food additives are removed through both catalytic degradation (R6G and MB) and adsorption (CIP and MLN).

Adjusting Ion Diffusion Kinetics of Li Deposition Enabled by an Elastic Porous Melamine Sponge Host for Stable Lithium Metal Anodes.

Lithium (Li) dendritic growth and huge volume expansion seriously hamper Li-metal anode development. Herein, we design a lightweight 3D Li-ion-affinity host enabled by silver (Ag) nanoparticles fully decorating a porous melamine sponge (Ag@PMS) for dendrite-free and high-areal-capacity Li anodes. The compact Ag nanoparticles provide abundant preferred nucleation sites and give the host strong conductivity. Moreover, the high specific surface area and polar groups of the elastic, porous melamine sponge enhance the Li-ion diffusion kinetics, prompting homogeneity of Li deposition and stripping. As expected, the integrated 3D Ag@PMS-Li anode delivered a remarkable electrochemical performance, with a Coulombic efficiency (CE) of 97.14% after 450 cycles at 1 mA cm-2. The symmetric cell showed an ultralong lifespan of 3400 h at 1 mA cm-2 for 1 mAh cm-2. This study provides a facile and cost-effective strategy to design an advanced 3D framework for the preparation of a stable dendrite-free Li metal anode.

An outbreak of renal failure in asian dogs due to s-triazine adulteration of pet food raw material: Analysis of unique, green kidney stones formed as a result.

Renoliths were removed at necropsy from dogs that had died from acute kidney injury in Asia in 2004 and submitted to our laboratories for analysis including elemental composition, mass spectrometry, and nuclear magnetic resonance spectroscopy. The presence of a mixed s-triazine matrix comprising melamine, cyanuric acid, and ammelide, but no detectable ammeline, was found in the stone samples we analyzed. The unusual and unique green coloration of these stones was determined to be due to the presence of biliverdin. The occurrence of these green stones distinguished the 2004 incident from another incident in 2007 in the USA and other reported cases. The presence of crystals was reported in renal tubules and collecting ducts in both outbreaks, but no stones were reported in the 2007 incident. This difference suggested a variation in the disease process caused by mixed s-triazine ingestion. Careful monitoring of food additives is warranted to prevent future problems in animals and humans.

Recovery of gaseous fuels through CO2-mediated pyrolysis of thermosetting polymer waste.

Thermosetting polymers are used in a wide range of applications due to their robust mechanical strength and superior flame retardancy. Despite these technical benefits, recycling of thermosetting polymers has been challenging because of their crosslinking nature. Moreover, their disposal through conventional methods (landfill and combustion) poses environmental concerns, such as microplastics and air pollutants. To address these issues, this study introduces a thermo-chemical disposal platform for thermosetting polymer wastes that employs carbon dioxide (CO2) as a reactive medium. In this work, melamine-formaldehyde was used as model compound of thermosetting polymers. In single-stage pyrolysis, it was revealed that CO2 plays a crucial role in controlling in the compositional matrices of pyrolytic gases, liquid products, and wax. These compositional changes were attributed to the homogeneous reactions between CO2 and the volatile compounds released from the thermolysis of MF. To enhance the thermal cracking of the MF, a double-stage pyrolysis process was tested, which increased the production of pyrolytic gases and eliminated wax formation. However, the slow kinetics governing the reactivity of CO2 limits the occurrence of homogeneous reactions. A nickel-based catalyst was used to accelerate reaction kinetics. The catalytic pyrolysis under CO2 conditions led to substantial increases in syngas (H2 and CO) production of 880% and 460%, respectively, compared with double-stage pyrolysis. These findings demonstrate that thermosetting polymer wastes can be valorized into gaseous fuels through thermo-chemical process, and CO2 enhances the recovery of energy and chemicals. Therefore, this study presents an innovative technical platform to convert thermosetting polymer wastes and CO2 into syngas.

Biomass-activated carbon-based superhydrophobic sponge with photothermal properties for adsorptive separation of waste oil.

The increasing discharge of oily wastewater from life poses a serious threat to the ecological environment and human health. To develop green, efficient, and low-cost materials for oil-water separation, a superhydrophobic photothermal oil-absorbing sponge (CAC-PDA@MF) was prepared by using nanoscale coconut shell activated carbon (CAC) loaded on a melamine sponge in this study. The sponge had excellent superhydrophobicity (WCA of 159.53°) due to the reduction of surface energy by grafting long-chain silanes. The adsorption capacity of the sponge was 69.04 g/g-158.27 g/g for a wide range of oils and organic solvents, and the sponge had excellent mechanical properties for multiple adsorption and recovery of oil. After 50 cycles of oil-water separation, its separation efficiency was maintained at over 98 %. In addition, the material had high acid, alkali, and salt resistance as well as excellent photothermal conversion properties. Its surface temperature rose rapidly to 100 °C and above, at a light intensity of 1.0 kW/m2. The material was capable of adsorbing and recovering high-viscosity oils that were solid or semi-solid at room temperature. Its versatility and commercial value made it a promising candidate for a wide range of applications.

Effect of crosslinker/porogen ratio on sponge-nested polymer monoliths for solid-phase extraction.

Polymer monoliths can be polymerised within different molds, but limited options are available for the preparation of free-standing polymer monoliths for analytical sample preparation, and in particular, solid-phase extraction (SPE). Commercial melamine-formaldehyde sponges can be used as supports for the preparation of polymer monoliths, due its flexibility, giving various shapes to monoliths. Herein, the crosslinker/porogen ratio of highly porous sponge-nested divinylbenzene (DVB) polymer monoliths has been evaluated. Monoliths prepared using different crosslinker/porogen ratios were applied to the extraction of bisphenol F, bisphenol A, bisphenol AF, and bisphenol B. Monoliths containing 50 wt % DVB and 50 wt % porogens presented the highest recovery of bisphenols. Under the optimised conditions, the developed method showed a linear range between 2.5 µg L-1 and 150 µg L-1 for BPA and BPAF, and between 5 µg L-1 and 150 µg L-1 for BPB and BPF. The limits of detection (LOD, S/N = 3) and limits of quantification (LOQ, S/N = 10) ranged from 0.36 µg L-1 to 1.09 µg L-1, and from 1.20 µg L-1 to 3.65 µg L-1, respectively. The recoveries for spiked bisphenols (10 µg L-1) in tap water and water contained in a polycarbonate containers were between 82 % and 114 %.

Probing the effect of protein corona on SERS signals: insights from melamine detection in milk matrix.

Matrix effects limit the application of surface-enhanced Raman scattering (SERS) technology in the field of food safety. This study elucidated it from the perspective of protein corona by employing a model system for melamine SERS detection in milk. Compared with the melamine standard solution, higher detection limits (1 mg/L and 10 mg/L) are observed in milk matrix. The melamine signal exhibits an 80% reduction in whey protein solution, suggesting that protein has a significant impact on SERS signals. The changes in particle size, zeta potential and UV-vis spectra indicate the AuNPs interact with whey protein. Forming protein corona inhibits the melamine-induced AuNPs aggregation, reducing the number of 'hot spot' and the adsorption of melamine on AuNPs (from 0.28 mg/L to 0.07 mg/L), which may be responsible for signal loss. The found matrix effect from protein corona provides new insights for developing strategies about reducing matrix effect in SERS application.

Design and preparation of a novel Mg-Al LDH@EDTA-Melamine nanocomposite for effective adsorptive removal of methylene blue and rhodamine B dyes from water.

This paper deals with the preparation of a novel nanocomposite consisted of magnesium-aluminum layered double hydroxide (Mg-Al LDH) and ethylenediaminetetraacetic acid (EDTA) as well as melamine (MA) as an adsorbent. This nanocomposite was utilized to adsorb different dyes such as rhodamine B (RhB) and methylene blue (MB) from water. The prepared adsorbent was characterized using FT-IR, EDS, XRD, TGA, and FE-SEM analyses. The effects of various parameters such as concentration, time, adsorbent dosage, temperature, and pH were tested to investigate their influence on adsorption conditions. Both methylene blue and rhodamine B dyes showed pseudo-second-order adsorption kinetics, and their adsorption followed the Langmuir isotherm. Moreover, the maximum adsorption capacities for methylene blue and rhodamine B were found to be 1111.103 mg/g at 45 °C and 232.558 mg/g at 60 °C, respectively. Additionally, the adsorption processes were found to be spontaneous (ΔG°< 0, for both dyes) and exothermic (ΔH° = -12.42 kJ/mol for methylene blue and ΔH° = -25.84 kJ/mol for rhodamine B) for both dyes. Hydrogen bonding and electrostatic forces are responsible for the interactions occur between the nanocomposite and the functional groups in the dyes. The experimental findings demonstrated a greater adsorption rate of MB than RhB, suggesting the adsorbent's stronger affinity for MB. This preference is likely due to MB's size, specific functional groups, and smaller molecule size, enabling stronger interactions and more efficient access to adsorption sites compared to RhB. Even after recycling 4 times, the dye adsorption percentages of the adsorbent for MB and RhB dyes were 90 % and 87 %, but the desorption percentages of the adsorbate dyes were 85 % and 80 %, respectively. The prepared adsorbent boasts several unique properties, such as the swift and effortless adsorption of MB and RhB dyes, straightforward synthesis, mild adsorption conditions, remarkable efficiency, and the ability to be recycled up to 4 times without a significant decrease in activity.

Enhancement in Sensitivity and Selectivity of Electrochemical Technique with CuO/g-C3N4 Nanocomposite Combined with Molecularly Imprinted Polymer for Melamine Detection.

This study focused on enhancing the sensitivity and selectivity to detect melamine by utilizing a photoelectrochemical method. This was achieved by combining a melamine-imprinted polymer with a CuO/g-C3N4 nanocomposite, which was synthesized through chemical precipitation and calcination. The resulting nanocomposite exhibits improved carrier mobility and photoelectrochemical properties. A molecularly imprinted receptor for selective detection was created through bulk polymerization with methacrylic acid and a melamine template. The characterization of the nanocomposite was performed using X-ray photoelectron spectroscopy for the chemical oxidation state, X-ray diffraction patterns for the crystalline structure, and ultraviolet/visible/near-infrared spectroscopy for optical properties. The CuO/g-C3N4 nanocomposite exhibits photoactivity under visible light. The modified electrode, incorporating the CuO/g-C3N4 nanocomposite and melamine-imprinted polymer, demonstrates a linear detection range of 2.5 to 50 nM, a sensitivity of 4.172 nA/nM for melamine, and a low detection limit of 0.42 nM. It shows good reproducibility and high selectivity to melamine, proving effective against interferences and real samples, showcasing the benefits of the molecularly imprinted polymer.

A Novel Intumescent MCA-Modified Sodium Silicate/Acrylic Flame-Retardant Coating to Improve the Flame Retardancy of Wood.

The incompatibility between inorganic flame retardants and organic acrylic coatings represents a significant challenge that requires resolution. This work selected environmentally friendly organic aqueous acrylic coatings as the substrate, sodium silicate hydrate as the inorganic flame retardant, and melamine cyanurate (MCA) as the flame-retardant modifier and the flame-retardant co-modifier, with the objective of improving the dispersion and flame-retardant properties of sodium silicate hydrate in the aqueous acrylic coatings. Subsequently, the sodium silicate/MCA/waterborne acrylic acid flame-retardant coating was prepared. The flame-retardant treatment was then applied to poplar veneer in order to create a flame-retardant poplar veneer. The dispersion of the flame-retardant coating was characterized by scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDX), and X-ray diffractometry (XRD). Furthermore, the flame-retardant properties of the flame-retardant poplar veneer were analyzed by thermogravimetry (TG), limiting oxygen index (LOI), and cone calorimeter. The results demonstrated that the MCA-modified sodium silicate flame retardant was well dispersed in aqueous acrylic coatings. The results of the flame-retardant properties of the poplar veneer indicated that the ignition time of the 9% flame retardant-treated poplar veneer was increased by 122.7%, the limiting oxygen index value was increased by 43.0%, and the peak heat release rate (pHRR), the peak total heat release rate (pTHR), and the peak mass loss rate were decreased by 19.9%, 10.8%, and 27.2%, respectively, in comparison to the non-flame retardant-treated poplar veneer. Furthermore, the residual char mass increased by 14.4%, and the residual char exhibited enhanced thickness, density, and regularity. The results demonstrated that MCA was an effective promoter of sodium silicate dispersion in acrylic coatings. Furthermore, the sodium silicate/MCA/waterborne acrylic flame-retardant coating significantly enhance the flame retardancy of wood, and its flame retardant mechanism was consistent with the synergistic silicone-nitrogen expansion flame-retardant mechanism. This work presents a novel approach to enhancing the dispersion of inorganic flame retardants in organic coatings, offering a valuable contribution to the advancement of research and application in the domains of innovative flame retardant coatings and flame retardant wood.

Nootkatone Counteracts Melamine-Mediated Nephrotoxicity via Modulation of Intermediate Filament Proteins, Oxidative, Inflammatory, and Apoptotic Events.

Background: Nootkatone (NK), a bioactive sesquiterpene ketone, is a major ingredient in grapefruit that has distinguished biological activities. Melamine (MM), a food adulterant, was reported to induce toxic effects including renal disorders. Hence, this protocol was devoted to evaluate the renoprotective impact of NK toward MM-evoked renal damage. Methods: Rats were either exposed to MM (700 mg/kg) or a combination of MM and two doses of NK (5 and 10 mg/kg). Results: The results showed that NK therapy notably decreased the kidney functional parameters, along with KIM-1 and NGAL expressions of MM group. Furthermore, a decrease in MDA and NO levels as well as an elevation in SOD, CAT, GSH, and SOD and NRF2 mRNA expression in the NK group demonstrated NK's ability to enhance the renal antioxidant defense of the MM group. Significant suppression in renal inflammatory markers was achieved by NK via lessening of IL-1ß and TNF-α, besides downregulation of NF-κB and IL-1ß expressions. NK also downregulated vimentin, nestin, and desmin in the MM group. Additionally, in response to the MM exposure, NK hindered renal apoptosis by decreasing caspase-3 expression and restoring renal histopathological features. Conclusion: These outcomes suggest that NK can be considered as a prospective candidate to guard against MM exposure-mediated renal toxic effects.

Three-dimensional nanoporous gold/gold nanoparticles substrate for surface-enhanced Raman scattering detection of illegal additives in food.

Owing to their nanoscale size and porous structure, both colloidal gold nanoparticles (AuNPs) and nanoporous gold (NPG) have demonstrated good and stable surface-enhanced Raman scattering (SERS) activity, and are therefore widely used as SERS substrates for the rapid detection of various components in food, environmental, biological, and other samples. In this study, we fabricated a novel, sensitive, and reproducible composite three-dimensional (3D) substrate for rapid SERS-based detection of illegal additives in food products. AuNPs and NPGs were prepared by chemical reduction and chemical dealloying methods, with the particle size of AuNPs about 60 nm and the pore size of NPG in the range of 5-36 nm. The AuNPs were then assembled on the surface of NPG to form the composite substrate 3D-NPG/AuNPs, which was characterized by transmission electron microscopy, scanning electron microscopy, X-ray diffraction, and other methods. Finally, the new SERS substrate combined with a portable Raman spectrometer was used to detect the illegal food additives 6-benzylaminopurine and melamine, with detection limits of 1 × 10-9 M and 5 × 10-7 M respectively. We further analyzed the relationship between the dealloying time-controlled morphology and the SERS properties of NPG, demonstrating that 3D-NPG/AuNPs as a novel SERS substrate have strong practical application potential in the rapid detection of food additives and other substances.

Aptamer based hybrid monolithic pipette tips supported by melamine sponge for enrichment of proteins.

BACKGROUND: The convenient preparation and application of functionalized organic-inorganic hybrid monolithic materials have obtained substantial interest in the pretreatment of complex samples by solid-phase extraction (SPE). Compared to the in-tube solid-phase microextraction in fused-silica capillaries, micro SPE in plastic pipette tips have fascinating merits for the easily operated enrichment of trace target analytes from biological samples. However, the poor compatibility of organic-inorganic hybrid monoliths with plastics leads to the rare appearance of commercial hybrid monolithic pipette tips (HMPTs). Therefore, how to synthesize the organic-inorganic hybrid monolithic materials with better extraction performance in plastic pipette tips becomes a challenge. RESULTS: We develop a facile and cheap strategy to immobilize organic-inorganic hybrid monoliths in pipette tips. Melamine sponge was employed as the supporting skeleton to in situ assemble amine- and thiol-bifunctionalized hybrid monolithic material via "one pot" in a pipette tip, and gold nanoparticles (GNPs) and thiol-modified aptamer against human α-thrombin were sequentially attached to the hybrid monolith within the HMPTs. The average coverage density of the aptamer with GNPs as an intermediary reached as high as 818.5 pmol µL-1. The enriched thrombin concentration was determined by a sensitive enzymatic chromogenic assay with the limit of detection of 2 nM. The extraction recovery of thrombin at 10 nM in human serum was 86.1 % with a relative standard deviation of 6.1 %. This proposed protocol has been applied to the enrichment and determination of thrombin in real serum sample with strong anti-interference ability, low limit of detection and high recovery. SIGNIFICANCE: The amine- and thiol-bifunctionalized HMPTs prepared with sponge as the skeleton frame provided a novel substrate material to decorate aptamers for efficient enrichment of proteins. This enlightens us that we can take advantage of the tunability of sponge assisted HMPTs to produce and tailor a variety of micro SPE pipette tips for broader applications on the analysis of trace targets in complex biological, clinic and environmental samples.