Hydrogenolysis of Poly(Ethylene-co-Vinyl Alcohol) and Related Polymer Blends over Ruthenium Heterogeneous Catalysts.

The hydrogenolysis of polymers is emerging as a promising approach to deconstruct plastic waste into valuable chemicals. Yet, the complexity of plastic waste, including multilayer packaging, is a significant barrier to handling realistic waste streams. Herein, we reveal fundamental insights into a new chemical route for transforming a previously unaddressed fraction of plastic waste - poly(ethylene-co-vinyl alcohol) (EVOH) and related polymer blends - into alkane products. We report that Ru/ZrO2 is active for the concurrent hydrogenolysis, hydrogenation, and hydrodeoxygenation of EVOH and its thermal degradation products into alkanes (C1-C35) and water. Detailed reaction data, product analysis, and catalyst characterization reveal that the in-situ thermal degradation of EVOH forms aromatic intermediates that are detrimental to catalytic activity. Increased hydrogen pressure promotes hydrogenation of these aromatics, preventing catalyst deactivation and improving alkane product yields. Calculated apparent rates of C-C scission reveal that the hydrogenolysis of EVOH is slower than low-density polyethylene. We apply these findings to achieve hydrogenolysis of EVOH/polyethylene blends and elucidate the sensitivity of hydrogenolysis catalysts to such blends. Overall, we demonstrate progress towards efficient catalytic processes for the hydroconversion of waste multilayer film plastic packaging into valuable products.

Influence of Curcuma Longa extract in citral addition on functional properties of thin films with triple-layer structure based on furcellaran and gelatin.

In this study, we obtained triple-layer films based on furcellaran and gelatin, in which the middle layer was enriched with extract of Curcuma longa in citral. This newly developed material underwent a comprehensive characterisation process to identify significant improvements in its functional properties. Both SEM, XRD and FTIR analyzes indicated the formation of interactions not only between the components but also between the film layers. Notably, the incorporation of the natural extract led to a significant reduction in solubility, decreasing it from 74.79 % to 57.25 %, while enhancing thermal stability expressed as a melting point elevating it from 147.10 °C in the control film to 158.80 °C in the film with the highest concentration of the active ingredient. Simultaneously, the addition of this active ingredient resulted in decreased water contact angle (WCA) values, rendering the film more hydrophilic. The produced films exhibit great promise as packaging materials, particularly within the food industry, and the conducted research is marked by its forward-looking and developmental approach.

Effect of Glass Transition Temperature on Enhanced Dielectric Breakdown Strength and Lifetime of Multilayer Polymer Films.

High temperature, high energy density, and low loss dielectric films are promising candidates for miniaturized capacitors in electric vehicles and high-speed trains. However, single-component polymers could not achieve these desired properties simultaneously. Polymer multilayer films (MLFs), which combine a high dielectric constant polymer [e.g., poly(vinylidene fluoride) (PVDF)] and a high breakdown/low loss polymer [e.g., polycarbonate (PC)] in a unique layered structure, have the potential achieve them at the same time. In this work, the effects of PC glass transition temperature (Tg) on the dielectric insulation properties (breakdown strength and lifetime) were investigated at high temperatures of 100-150 °C. Three PC materials had Tg values of 145 (PC1), 165 (PC2), and 185 °C (PC3), respectively. It is observed that MLF-PC3 with the highest Tg of PC exhibited the highest Weibull direct/alternating current (DC/AC) breakdown strength and the longest DC/AC lifetime, whereas MLF-PC1 with the lowest Tg showed the lowest Weibull DC/AC breakdown strength and the shortest DC/AC lifetime. A high-temperature high-volage leakage current study revealed that MLF-PC3 exhibited the lowest bulk conductivity at all temperatures under different electric fields. The knowledge obtained from this study will help us design better MLFs with high performance for next-generation miniaturized capacitors.

Monte Carlo Computer Simulations of Spin-Transfer Torque.

This article performs computer simulations of the change in magnetization in the ferromagnetic film when polarized electric current passes through it. The model examines multilayer structures from ferromagnetic and nonmagnetic films. A sandwich system comprises two ferromagnetic layers separated by a nonmagnetic gasket. Ferromagnetic films have different magnetic susceptibility. The first ferromagnetic film is magnetically hard and acts as a fixed layer. The second ferromagnetic film is magnetically soft, with a switched direction of magnetization. The current direction is perpendicular to the film plane (CPP geometry). Spin transfer is carried out by electrons that polarize in the first ferromagnetic film and transmit spin to the second ferromagnetic film. We use the Ising model to describe the magnetic properties of the system and the Metropolis algorithm to form the thermodynamic states of the spin system. Simulations are performed at temperatures below the Curie points for both materials. The result of computer simulation is the dependence of magnetization in the magnetically soft film on the current strength in the system. Calculations show that there is a critical value of the current at which the magnetization sign of the controlled film changes. The magnetization versus current plot is stepwise. The change in the magnetization sign is due to an increase in the polarization of the electron gas. The plot of electron gas polarization versus current is also stepwise.

A signal amplification for Trp isomers electrochemical recognition based on PEDOT:PSS and CS/PAA multilayers.

In this work, enhanced tryptophan (Trp) isomers recognition was successfully demonstrated on (CS/PAA)3.5@PEDOT:PSS/GCE, a multilayer chiral sensor with good stability and reproducibility. The (CS/PAA)n multilayers chiral interface was first fabricated via alternating self-assembly of chiral chitosan (CS) and achiral polyacrylic acid (PAA). Conductive PEDOT:PSS was then compounded with (CS/PAA)n multilayers to obtain the chiral sensor for the electrochemical recognition of Trp isomers. The structure of the sensor and its chirality properties for Trp isomers were characterized by fourier transform infrared spectroscopy (FT-IR)，scanning electron microscopy (SEM) and electrochemical methods. The SEM images showed uniform distribution of PEDOT:PSS in the multilayer films, which changed the internal structure of the (CS/PAA)3.5. Consequently, (CS/PAA)3.5@PEDOT:PSS multilayers rendered more chiral centers in addition to improved good conductivity, which significantly amplified the oxidation peak current ratio of D-Trp to L-Trp (ID/IL) up to 6.71 at 25 °C. In addition, a linear relationship was observed between the peak current and Trp enantiomer concentration in the range of 0.002-0.15 mM, and the detection limits of D-Trp and L-Trp were 0.33 and 0.67 µM, respectively. More importantly, the percentage of D-Trp in non-racemic Trp enantiomers mixture solutions were successfully determined on the chiral interface, showing its effectiveness and promising potential in practical applications.

Resilient high oxygen barrier multilayer films of nanocellulose and polylactide.

Nanocelluloses are promising high gas barrier materials for biobased food packaging, but they must be protected from water to preserve high performance. The respective O2 barrier properties of different types of nanocelluloses were compared (nanofibers (CNF), oxidized nanofibers (CNF TEMPO) and nanocrystals (CNC)). The oxygen barrier performance for all types of nanocelluloses was similarly high. To protect the nanocellulose films from water, a multilayer material architecture was used with poly(lactide) (PLA) on the outside. To achieve this, a biobased tie layer was developed, using Corona treatment and chitosan. This allowed thin film coating with nanocellulose layers between 60 and 440 nm thickness. AFM images treated with Fast Fourier Transform showed the formation of locally-oriented CNC layers on the film. Coated PLA(CNC) films performed better (3.2 × 10-20 m3.m/m2.s.Pa) than PLA(CNF) and PLA(CNF TEMPO) (1.1 × 10-19 at best), because thicker layers could be obtained. The oxygen barrier properties were constant during successive measurements at 0 % RH, 80 % RH and again at 0 % RH. This shows that PLA is sufficiently shielding nanocelluloses from water uptake to keep high performance in an extended range of RH and opens the way to high oxygen barrier films which are biobased and biodegradable.

Stimuli-responsive polyelectrolyte multilayer films and microcapsules.

Polyelectrolyte multilayer (PEM) films and particularly hollow capsules composed of PEM shells have gained significant interest since their introduction. Their compositional versatility and easiness of preparation via so-called layer-by-layer assembly led to the development of numerous systems containing also stimuli-responsive components. This paper reviews the achievements related to the formation, determination of structure, and properties of PEM films and capsules responding to major physical, chemical, and biological stimuli. Their applications as e.g., microcarriers for controlled delivery release of active components, substrates for controlled cells' growth, coatings for enhanced surface adhesion, or self-healing anticorrosive systems are shown and discussed. The influence of various stimuli on integrity, permeability of the films or capsules shell are presented together with related applications in biomedicine for controlled drug release as well as in biotechnology and industrial protective coatings.

Real-Time Transformation of Flux-Closure Domains with Superhigh Thermal Stability.

Polar topologies have received extensive attention due to their exotic configurations and functionalities. Understanding their responsive behaviors to external stimuli, especially thermal excitation, is highly desirable to extend their applications to high temperature, which is still unclear. Here, combining in situ transmission electron microscopy and phase-field simulations, the thermal dynamics of the flux-closure domains were illuminated in PbTiO3/SrTiO3 multilayers. In-depth analyses suggested that the topological transition processes from a/c domains to flux-closure quadrants were influenced by the boundary conditions of PbTiO3 layers. The symmetrical boundary condition stabilized the flux-closure domains at higher temperature than in the asymmetrical case. Furthermore, the reversible thermal responsive behaviors of the flux-closure domains displayed superior thermal stability, which maintained robust up to 450 °C (near the Curie temperature). This work provides new insights into the dynamics of polar topologies under thermal excitation and facilitates their applications as nanoelectronics under extreme conditions.

Evaluation of Improvements in the Separation of Monolayer and Multilayer Films via Measurements in Transflection and Application of Machine Learning Approaches.

Small plastic packaging films make up a quarter of all packaging waste generated annually in Austria. As many plastic packaging films are multilayered to give barrier properties and strength, this fraction is considered hardly recyclable and recovered thermally. Besides, they can not be separated from recyclable monolayer films using near-infrared spectroscopy in material recovery facilities. In this paper, an experimental sensor-based sorting setup is used to demonstrate the effect of adapting a near-infrared sorting rig to enable measurement in transflection. This adaptation effectively circumvents problems caused by low material thickness and improves the sorting success when separating monolayer and multilayer film materials. Additionally, machine learning approaches are discussed to separate monolayer and multilayer materials without requiring the near-infrared sorter to explicitly learn the material fingerprint of each possible combination of layered materials. Last, a fast Fourier transform is shown to reduce destructive interference overlaying the spectral information. Through this, it is possible to automatically find the Fourier component at which to place the filter to regain the most spectral information possible.

Graphene Oxide Thin Films with Drug Delivery Function.

Graphene oxide has been used in different fields of nanomedicine as a manager of drug delivery due to its inherent physical and chemical properties that allow its use in thin films with biomedical applications. Several studies demonstrated its efficacy in the control of the amount and the timely delivery of drugs when it is incorporated in multilayer films. It has been demonstrated that oxide graphene layers are able to work as drug delivery or just to delay consecutive drug dosage, allowing the operation of time-controlled systems. This review presents the latest research developments of biomedical applications using graphene oxide as the main component of a drug delivery system, with focus on the production and characterization of films, in vitro and in vivo assays, main applications of graphene oxide biomedical devices, and its biocompatibility properties.

Polyelectrolyte Multilayer Films as a Potential Buccal Platform for Drug Delivery.

The goal of this research was to study the potential of polyelectrolyte multilayers as buccal dosage forms for drug delivery and to investigate how the properties of the drugs impact the overall performance of the delivery system. Multilayer films based on the polyelectrolyte interaction between casein and chitosan were developed using benzydamine, tolfenamic acid and betahistine as model drugs. The samples were characterized for surface pH, moisture content and moisture absorption, swelling behavior and mucoadhesion. Additionally, surface morphology was investigated, as well as the drugs' physical state after incorporation in the multilayer films. The samples proved to be non-irritant (pH was within the physiological range), physically stable (moisture content and moisture absorption below 5%) and mucoadhesive, adsorbing from 60 to 70% mucin. The release behavior corelated to the swelling index profiles of the samples and was strongly dependent on the drug solubility. The developed multilayer films appeared to be an optimum delivery system for sparingly soluble drugs due to the high drug loading achieved.

Quality and Shelf-Life Stability of Pork Meat Fillets Packaged in Multilayer Polylactide Films.

In the present study, the effectiveness of a multilayer film of polylactide (PLA), fully bio-based and compostable, was ascertained to develop a novel sustainable packaging solution for the preservation of fresh pork meat. To this end, the multilayer PLA films were first characterized in terms of their thermal characteristics, structure, mechanical performance, permeance to water and aroma vapors and oxygen, and optical properties and, for the first time, compared with two commercial high-barrier multilayer packaging films. Thereafter, the multilayers were thermosealed to package fillets of fresh pork meat and the physicochemical changes, lipid oxidation levels, and microbiological counts were monitored in the food samples during storage under refrigeration conditions. Results showed that the meat fillets packaged in PLA developed a redder color and showed certain indications of dehydration and oxidation, being more noticeably after 11 days of storage, due to the higher water vapor and oxygen permeance values of the biopolymer multilayer. However, the pH changes and bacterial growth in the cold-stored fresh pork meat samples were minimal and very similar in the three tested multilayer films, successfully accomplishing the requirements of the food quality and safety standards at the end of storage.

Development of an anti-infective coating on the surface of intraosseous implants responsive to enzymes and bacteria.

BACKGROUND: Bacterial proliferation on the endosseous implants surface presents a new threat to the using of the bone implants. Unfortunately, there is no effective constructed antibacterial coating which is bacterial anti-adhesion substrate-independent or have long-term biofilm inhibition functions. METHODS: Drug release effect was tested in Chymotrypsin (CMS) solution and S. aureus. We used bacterial inhibition rate assays and protein leakage experiment to analyze the in vitro antibacterial effect of (Montmorillonite/Poly-L-lysine-Chlorhexidine)10 [(MMT/PLL-CHX)10] multilayer film. We used the CCK-8 assay to analyze the effect of (MMT/PLL-CHX)10 multilayer films on the growth and proliferation of rat osteoblasts. Rat orthopaedic implant-related infections model was constructed to test the antimicrobial activity effect of (MMT/PLL-CHX)10 multilayer films in vivo. RESULTS: In this study, the (MMT/PLL-CHX)10 multilayer films structure were progressively degraded and showed well concentration-dependent degradation characteristics following incubation with Staphylococcus aureus and CMS solution. Bacterial inhibition rate assays and protein leakage experiment showed high levels of bactericidal activity. While the CCK-8 analysis proved that the (MMT/PLL-CHX)10 multilayer films possess perfect biocompatibility. It is somewhat encouraging that in the in vivo antibacterial tests, the K-wires coated with (MMT/PLL-CHX)10 multilayer films showed lower infections incidence and inflammation than the unmodified group, and all parameters are close to SHAM group. CONCLUSION: (MMT/PLL-CHX)10 multilayer films provides a potential therapeutic method for orthopaedic implant-related infections.

Feasibility Assessment of Parathyroid Hormone Adsorption by Using Polysaccharide-Based Multilayer Film Systems.

Chronic kidney disease (CKD) is a systemic disorder that combines complex bone and mineral abnormalities. The high level of parathyroid hormone (PTH) in the blood causes irreversible renal dysfunction and cardiovascular disease. Therefore, it is necessary to reduce level of PTH in the blood of patients with uremic state. In this study, chitosan and heparin were chosen to form polysaccharide-based multilayer films based on their antibacterial ability, good biocompatibility and hemocompatibility. In addition, a previous study has revealed that PTH is a heparin/polyanion binding protein because of the similarity of heparin to the cell surface proteoglycans. Subsequently, the surface properties including thickness, surface hydrophobicity and surface charge of a series of multilayer films were analyzed. The PTH adsorption rate of a series of multilayer films was also assessed. The results revealed that the optimizing condition is (CHI/HEP)2.5 and 60 min in both PBS only and PBS with the addition of bovine serum albumin, which demonstrated the specific adsorption of PTH on the materials. Furthermore, the hemolysis test also revealed that (CHI/HEP)2.5 shows good blood compatibility. It is considered that polysaccharide-based multilayer films may provide an alternative for the surface modification of hemodialysis membranes and equipment.

Antibiotic-Loaded MMT/PLL-Based Coating on the Surface of Endosseous Implants to Suppress Bacterial Infections.

BACKGROUND: Bone infections remain one of the most common and serious complications of orthopedic surgery, posing a tremendous economic burden to society and patients. This is because bacteria colonize and multiply on the surface of the implant. The (MMT/PLL)8 multilayer films have been shown to effectively release antibiotics depending on the changes in the microenvironment. Here, vancomycin was loaded into the (MMT/PLL)8 multilayer films, which were prepared to be used as a local delivery system for the treatment of bone infections. METHODS: We used the layer-by-layer self-assembly method to prepare VA-loaded coatings (MMT/PLL-VA)8 consisting of montmorillonite (MMT), poly-L-lysine (PLL), and VA. The thickness and surface morphology of coatings were characterized using spectroscopic ellipsometry and scanning electron microscopy (SEM). In order to evaluate the drug release behavior from coatings in different media, we measured the size of the zone of inhibition. Additionally, in vitro antibacterial activity was assessed using the shake-flask culture method and SEM images, while that of in vivo was evaluated by establishing an animal model of bone infection. RESULTS: Our findings revealed that small-molecule antibiotics were successfully loaded into the (MMT/PLL-VA)8 multilayer film structure during the hierarchical self-assembly process and subsequently the multilayer film structure depicted linear growth behavior. The PLL in the multilayer films was progressively degraded which triggered the VA release when contacted with CMS or bacterial infections. The release of VA from multilayer film structure depends on the concentration changes of CMS. Notably, the multilayer films presented great in vitro cell compatibility. Moreover, the prepared antibacterial multilayer films showed excellent antibacterial property by killing more than 99.99% of S. aureus in 24 h. More importantly, we found that multilayer film exhibits good sterilization effect and biocompatibility under the stimulation of bacterial liquid both in vitro and in vivo antibacterial ability tests. CONCLUSION: Altogether, this study shows that (MMT/PLL-VA)8 multilayer films containing CMS and bacteria-responsive drug release properties posess high bactericidal activity and good biocompatibility. This finding provides a novel strategy for the treatment of bone infections.

Review on the photonic techniques suitable for automatic monitoring of the composition of multi-materials wastes in view of their posterior recycling.

In the increasingly pressing context of improving recycling, optical technologies present a broad potential to support the adequate sorting of plastics. Nevertheless, the commercially available solutions (for example, employing near-infrared spectroscopy) generally focus on identifying mono-materials of a few selected types which currently have a market-interest as secondary materials. Current progress in photonic sciences together with advanced data analysis, such as artificial intelligence, enable bridging practical challenges previously not feasible, for example in terms of classifying more complex materials. In the present paper, the different techniques are initially reviewed based on their main characteristics. Then, based on academic literature, their suitability for monitoring the composition of multi-materials, such as different types of multi-layered packaging and fibre-reinforced polymer composites as well as black plastics used in the motor vehicle industry, is discussed. Finally, some commercial systems with applications in those sectors are also presented. This review mainly focuses on the materials identification step (taking place after waste collection and before sorting and reprocessing) but in outlook, further insights on sorting are given as well as future prospects which can contribute to increasing the circularity of the plastic composites' value chains.

Impacts of Mechanical Stiffness of Bacteriophage-Loaded Hydrogels on Their Antibacterial Activity.

The elaboration of efficient hydrogel-based materials with antimicrobial properties requires a refined control of defining their physicochemical features, which includes mechanical stiffness, so as to properly mediate their antibacterial activity. In this work, we design hydrogels consisting of polyelectrolyte multilayer films for the loading of T4 and φX174 bacteria-killing viruses, also called bacteriophages. We investigate the antiadhesion and bactericidal performances of this biomaterial against Escherichia coli, with a specific focus on the effects of chemical cross-linking of the hydrogel matrix, which, in turn, mediates the hydrogel stiffness. Depending on the latter and on phage replication features, it is found that the hydrogels loaded with the bacteria-killing viruses make both contact killing (targeted bacteria are those adhered at the hydrogel surface) and release killing (planktonic bacteria are the targets) possible with ca. 20-80% efficiency after only 4 h of incubation at 25 °C as compared to cases where hydrogels are free of viruses. We further demonstrate the lack of dependence of virus diffusion within the hydrogel and of the maximal viral storage capacity on the hydrogel mechanical properties. In addition to the evidenced bacteriolytic activity of the phages loaded in the hydrogels, the antimicrobial property of the phage-loaded materials is shown to be partly controlled by the chemistry of the hydrogel skeleton and, more specifically, by the mobility of the peripheral free polycationic components, known for their ability to weaken and permeabilize membranes of bacteria, the latter then becoming "easier" targets for the viruses.

Optimized PAH/Folic acid layer-by-layer films as an electrochemical biosensor for the detection of folate receptors.

Folate receptor alpha (FR-α) is a glycoprotein overexpressed in tumor cell surfaces, especially in gynecologic cancers, and can be used as a biomarker for diagnostics. Currently, FRα is quantified by positron emission tomography (PET) or fluorescence imaging techniques. However, these methods are costly and time-consuming. We report on the development of an electrochemical biosensor for FRα detection based on the use of nanostructured layer-by-layer (LbL) films as modified electrodes. Multilayer films were deposited on indium tin oxide (ITO) electrodes by the alternately assembling of positively charged polyallylamine hydrochloride (PAH) and negatively charged folic acid (FA), used as the biorecognition element. UV-vis and FTIR spectroscopies revealed the successful PAH and FA adsorption on ITO. Devices performance was evaluated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The [PAH/FA] films presented a good reproducibility (RSD of 1.12%) and stability when stored in the Tris-HCl solution (RSD 6.7%). The biosensor electrochemical response exhibited a linear relationship with FRα concentration in the range from 10 to 40 nM. The limit of detection reached for CV and EIS measurements were 0.7 and 1.5 nM, respectively. As a proof-of-concept, we show that the devices can differenciate tumor cells from healthy cell, showing an excellent selectivity. The biosensor device based on [PAH/FA] films represents a promising strategy for a simple, rapid, and low-cost cancer diagnosis through FRα quantification on the surface of cancer cells.

Multiscale Structural Evolution and Its Relationship to Dielectric Properties of Micro-/Nano-Layer Coextruded PVDF-HFP/PC Films.

An understanding of the structural evolution in micro-/nano-layer co-extrusion process is essential to fabricate high-performance multilayered products. Therefore, in this work, we reveal systematically the multiscale structural development, involving both the layer architecture and microstructure within layers of micro-/nano-layer coextruded polymer films, as well as its relationship to dielectric properties, based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP)/polycarbonate (PC) system. Interestingly, layer architecture and morphology show strong dependences on the nominal layer thicknesses. Particularly, with layer thickness reduced to nanometer scale, interfacial instabilities triggered by viscoelastic differences between components emerge with the creation of micro-droplets and micro-sheets. Films show an enhanced crystallization with the formation of two-dimensional (2D) spherulites in microlayer coextruded systems and the oriented in-plane lamellae in nanolayer coextruded counterparts, where layer breakup in the thinner layers further changes the crystallization behaviors. These macro- and microscopic structures, developed from the co-extrusion process, substantially influence the dielectric properties of coextruded films. Mechanism responsible for dielectric performance is further proposed by considering these effects of multiscale structure on the dipole switching and charge hopping in the multilayered structures. This work clearly demonstrates how the multiscale structural evolution during the micro-/nano-layer coextrusion process can control the dielectric properties of multilayered products.

Achieving Flat-on Primary Crystals by Nanoconfined Crystallization in High-Temperature Polycarbonate/Poly(vinylidene fluoride) Multilayer Films and Its Effect on Dielectric Insulation.

To meet the stringent requirements of next-generation film capacitors for power electronics, multilayer films (MLFs) are fabricated with the advantage of achieving high temperature rating, high energy density, and reasonably low loss simultaneously. In this study, a high permittivity polar polymer, poly(vinylidene fluoride) (PVDF), is multilayered with a linear, low loss dielectric polymer such as high-temperature polycarbonate (HTPC). However, the dielectric loss of these MLFs was still high as compared with current state-of-the-art biaxially oriented polypropylene (BOPP) films. The goal of this work is to decrease the dielectric loss and enhance dielectric insulation by achieving flat-on primary PVDF crystals in MLFs via nanoconfined melt-recrystallization. Based on simultaneous small- and wide-angle X-ray scattering experiments, edge-on lamellar crystals were observed for all as-extruded MLFs, regardless of different PVDF layer thicknesses. However, after melting at 180 °C followed by recrystallization, flat-on primary crystals were successfully achieved when the PVDF layer thickness was below 39 nm. Above 78 nm for the PVDF layer, major edge-on primary crystals with minor flat-on secondary crystals were observed. From leakage current, breakdown, lifetime, and electric displacement-electric field loop studies, MLFs with the flat-on primary crystals exhibited reduced loss and enhanced dielectric insulation as compared to as-extruded MLFs and those with edge-on primary/flat-on secondary crystals. This was attributed to the effective blockage of charge carriers by the flat-on PVDF primary crystals and their reduced ferroelectric switching.