Influence of Etchants on Etched Surfaces of High-Strength and High-Conductivity Cu Alloy of Different Processing States.

With the continuous integration of semiconductor devices, the requirements of the size accuracy and surface quality of etched lead frames are stricter. The etchant is a key factor in the etching process and etched surface quality, while the effects of the difference in etchants on the etched surface morphology of Cu alloy have not been directly studied. In this study, aqua regia, acidic FeCl3 and two CuCl2 solutions were used as etchants, and different CuCrSn specimens were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocations have significant influences on the local etching rate. The preferential etching of some atomic planes forms steps between the grains with different orientations, and preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For the surfaces etched by the FeCl3 and CuCl2 etchants, the steps and grooves are blurred; thus, they are less rough. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high-density Cr-rich particles remain on the surfaces etched by the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism, rate and the etched surface morphology.

Discoloration and Surface Changes in Spruce Wood after Accelerated Aging.

Spruce wood is widely used in outdoor applications, but its susceptibility to degradation under exposure to sunlight and moisture is a major concern. This study investigates the impact of accelerated aging on spruce wood's surface chemistry, microstructure, geometry, and discoloration. The study was performed in two outdoor aging modes: dry and wet. The accelerated aging effects were evident in the changes in spruce wood structure, as well as in the other studied properties. During aging, it developed significant discoloration. Under simulated rainless outdoor conditions (dry mode), spruce wood gradually became dark brown. Under conditions involving rain (wet mode), the discoloration was qualitatively different from the dry mode. FTIR spectroscopy showed that during the accelerated aging of wood, lignin was mainly degraded, especially in the early stages of the process. A linear correlation was found between the changes in lignin and the color changes in the wood. There was an increase in carbonyl groups in the dry mode, which contributed to the color change and was also influenced by changes in extractives. The wet mode caused the leaching out of carbonyl groups. The observed decrease in cellulose crystallinity, together with the degradation of hydrophobic lignin, may result in the increased hydrophilicity of photodegraded wood. For both modes, there were different changes in the wood micro- and macrostructure, reflected in the surface morphology. The roughness increased during the aging process in both modes. The slightest changes in the roughness parameters were identified in the grain direction in the dry mode; the most evident was that the roughness parameters increased perpendicular to the grain in the wet mode. The demonstrated mechanism backing up the aging-related changes to the spruce wood structure and the relations unveiled between these changes and the changes in the spruce wood surface properties can provide an issue point for seeking ways how to mitigate the negative effects of the environmental factors the wood is exposed to.

Characterizing Surface Morphological and Chemical Properties of Commonly Used Orthopedic Implant Materials and Determining Their Clinical Significance.

The goal of the study was to compare the surface characteristics of typical implant materials used in orthopedic surgery and traumatology, as these determine their successful biointegration. The morphological and chemical structure of Vortex plate anodized titanium from commercially pure (CP) Grade 2 Titanium (Ti2) is generally used in the following; non-cemented total hip replacement (THR) stem and cup Ti alloy (Ti6Al4V) with titanium plasma spray (TPS) coating; cemented THR stem Stainless steel (SS); total knee replacement (TKR) femoral component CoCrMo alloy (CoCr); cemented acetabular component from highly cross-linked ultrahigh molecular weight polyethylene (HXL); and cementless acetabular liner from ultrahigh molecular weight polyethylene (UHMWPE) (Sanatmetal, Ltd., Eger, Hungary) discs, all of which were examined. Visualization and elemental analysis were carried out by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). Surface roughness was determined by atomic force microscopy (AFM) and profilometry. TPS Ti presented the highest Ra value (25 ± 2 µm), followed by CoCr (535 ± 19 nm), Ti2 (227 ± 15 nm) and SS (170 ± 11 nm). The roughness measured in the HXL and UHMWPE surfaces was in the same range, 147 ± 13 nm and 144 ± 15 nm, respectively. EDS confirmed typical elements regarding the investigated prosthesis materials. XPS results supported the EDS results and revealed a high % of Ti4+ on Ti2 and TPS surfaces. The results indicate that the surfaces of prosthesis materials have significantly different features, and a detailed characterization is needed to successfully apply them in orthopedic surgery and traumatology.

In vitro digestion of microplastics in human digestive system: Insights into particle morphological changes and chemical leaching.

Despite the well-reported occurrences and established pathways for microplastics (MPs) ingestion by humans, the eventual fate of these particles in the human gastrointestinal system is poorly understood. The present study tries to gain a better understanding of the fate of four common food-borne MPs, i.e. Polystyrene (PS), Polypropylene (PP), Low-density Polyethylene (LDPE), and Nylon, in a simulated in vitro human digestive system. Firstly, the changes in the physicochemical properties of 20-210 µm sized MPs as well as the leaching of chemicals were monitored using fluorescence microscopy, FTIR, and LC-QTOF-MS. Thereafter, the mass loss and morphological alterations in 3-4 mm sized MPs were observed after removing the organic matter. The interaction of PS and PP MPs with duodenal and bile juices manifested in a corona formation. The increase in surface roughness in PP MPs aligned with MP-enzyme dehydrogenation reactions and the addition of NO groups. A few fragments ranging from 30 to 250 µm, with negligible mass loss, were released during the MP digestion process. In addition, the leaching of compounds, e.g. capsi-amide, butanamide, and other plasticizers and monomers was also observed from MPs during digestion, and which may have the potential to accumulate and get absorbed by the digestive organs, and to subsequently impart toxic effects.

Effect of GaN Cap Thickness on the DC Performance of AlGaN/GaN HEMTs.

We prepared AlGaN/GaN high electron mobility transistors (HEMTs) with GaN cap thicknesses of 0, 1, 3, and 5 nm and compared the material characteristics and device performances. It was found that the surface morphology of the epitaxial layer was effectively improved after the introduction of the GaN cap layer. With the increase of the GaN cap thickness, the carrier concentration (ns) decreased and the carrier mobility (µH) increased. Although the drain saturation current (IdSat) of the device decreased with the increasing GaN cap thickness, the excessively thin GaN layer was not suitable for the cap layer. The thicker GaN layer not only improved the surface topography of the epitaxial layer but also effectively improved the off-state characteristics of the device. The optimal cap thickness was determined to be 3 nm. With the introduction of the 3 nm GaN cap, the IdSat was not significantly reduced. However, both the off-state gate leakage current (IgLeak) and the off-state leakage current (IdLeak) decreased by about two orders of magnitude, and the breakdown voltage (BV) increased by about 70 V.

Investigation of Perovskite Solar Cells Using Guanidinium Doped MAPbI3 Active Layer.

In this work, guanidinium (GA+) was doped into methylammonium lead triiodide (MAPbI3) perovskite film to fabricate perovskite solar cells (PSCs). To determine the optimal formulation of the resulting guanidinium-doped MAPbI3 ((GA)x(MA)1-xPbI3) for the perovskite active layer in PSCs, the perovskite films with various GA+ doping concentrations, annealing temperatures, and thicknesses were systematically modulated and studied. The experimental results demonstrated a 400-nm-thick (GA)x(MA)1-xPbI3 film, with 5% GA+ doping and annealed at 90 °C for 20 min, provided optimal surface morphology and crystallinity. The PSCs configured with the optimal (GA)x(MA)1-xPbI3 perovskite active layer exhibited an open-circuit voltage of 0.891 V, a short-circuit current density of 24.21 mA/cm2, a fill factor of 73.1%, and a power conversion efficiency of 15.78%, respectively. Furthermore, the stability of PSCs featuring this optimized (GA)x(MA)1-xPbI3 perovskite active layer was significantly enhanced.

Experimental Investigation on Diamond Band Saw Processing of Resin Mineral Composites.

Resin mineral composite (RMC) is a new material with several times the damping properties of gray cast iron and great corrosion resistance. Due to its overall brittleness, sawing with a diamond band saw would be a suitable method. In this research, sawing experiments are carried out to study the sawing force characteristics of the material and its surface morphology during the processing. The results show that the feed force level is in the range of 3.5~5.5 N and the tangential force level is relatively low. The distribution of resin mineral components does not have a significant impact on the average sawing force but increases the fluctuation of the lateral force signal. The maximum fluctuation volume is 94.86% higher than other areas. Uneven lateral force, generated when diamond particles pass through the resin-mineral interface, is one of the causes of fluctuations. The machined surface of RMC has uniform strip scratches and a small number of pits. Maintaining a constant ratio of sawing speed to feed speed can result in approximately the same machined surface. A step structure with a height of about 10 µm appears at the interface of resin minerals. As a processing defect, it may affect the performance of RMC components in some aspects, which need a further precision machining processing.

Understanding the Relationship between Surface Quality and Chip Morphology under Sustainable Cutting Environments.

Although chip morphology changes according to the machining method and related cutting parameters, chip formation affects the quality of the machined surface. In this context, it is very important to understand the relationship between chip morphology and surface quality, especially in materials that are difficult to machine. In the presented study, the changes in chip morphology, surface morphology, and surface quality criteria (Ra and Rz) that occurred during the milling of precipitation-hardened steel in different cutting environments were analyzed. Milling experiments were carried out in dry, MQL (minimum quantity lubrication), nano-MQL (graphene), nano-MQL (hBN), Cryo, and Cryo-MQL environments using TiAlN-coated inserts and three different cutting speeds and feed rates. While the highest values in terms of Ra and Rz were measured in dry machining, the minimum values were obtained in a nano-MQL (hBN) cutting environment. Due to the lubrication and low friction provided by the MQL cutting environment, chips were formed in thinner segmented forms. This formation reduced the chip curve radius and thus provided a more stable surface morphology. On the other hand, Cryo-ambient gas could not effectively leak into the cutting zone due to the intermittent cutting process, but it increased the brittleness of the chips with the cooling effect and provided a similar surface morphology. The values of minimum Ra and Rz were obtained as 0.304 mm and 1.825 mm, respectively, at a 60 m/min cutting speed and 0.04 mm/rev feed. Consequently, the use of nano-MQL cutting medium is seriously recommended in terms of surface quality in milling operations of difficult-to-machine materials.

Electrospun Poly-l-Lactic Acid Membranes Promote M2 Macrophage Polarization by Regulating the PCK2/AMPK/mTOR Signaling Pathway.

Electrospun membranes are widely used in tissue engineering. Regretfully, there is limited research on how its morphological characteristics precisely regulate macrophage activation and immune response. Therefore, electrospun poly-l-lactic acid (PLLA) membranes with different alignments (align and random) and diameters (nanoscale and microscale) are prepared to investigate the effects of different surface morphologies on M2 macrophage polarization. Additionally, transcriptome, proteome, and phosphoproteome sequencings are combined to examine the underlying regulatory mechanisms. The results show that the electrospun PLLA membranes with different surface morphologies have good biocompatibility and can regulate the phenotype and function of macrophages by changing the micromorphology of the matrix surface. Especially, macrophages cultured on the electrospun membranes of the A600 group exhibit higher M2 macrophage polarization than the other three groups. Furthermore, the findings demonstrate that electrospun PLLA membranes enhance AMP-activated protein kinase (AMPK)/ mammalian target of rapamycin (mTOR) signaling activation by upregulating the expression of integrin phosphoenolpyruvate carboxykinase 2 (PCK2), which is critical for M2 macrophage polarization. Taken together, electrospun PLLA membranes promote M2 macrophage polarization by regulating the PCK2/AMPK/mTOR signaling pathway. This research can provide further theoretical bases for scaffold design, immunoregulatory mechanisms, and clinical application based on electrospinning technology in the future.

Effect of different surface roughening treatment on polyether ether ketone and acrylic resin bonding: A pilot study.

BACKGROUND: As polyether ether ketone (PEEK) is a relatively new material in dentistry, its bonding properties with regard to dental acrylic base materials are not fully known. To ensure the long-term success of removable dentures with a PEEK framework, the base materials must be well bonded to each other. OBJECTIVES: The study aimed to investigate the effects of different kinds of surface roughening treatment on PEEK and acrylic resin bonding. MATERIAL AND METHODS: Eighty PEEK specimens (N = 80) were randomly divided into 5 groups (n = 16 per group) and subjected to various surface roughening treatment (control, grinding, sandblasting, tribochemical silica coating (CoJet), and sulfuric acid etching). Heat-polymerized acrylic resin was applied to the treated surfaces of the PEEK specimens. The shear bond strength (SBS) test, environmental scanning electron microscopy (ESEM) analysis and three-dimensional (3D) surface topography analysis were performed. The statistical analysis of the data was conducted using the analysis of variance (ANOVA) and Tukey's multiple comparison test. RESULTS: The one-way ANOVA showed significant differences in the SBS values between the groups (p = 0.001). Sandblasting, tribochemical silica coating and sulfuric acid etching resulted in high SBS values (p = 0.001). The highest SBS values were observed in the sulfuric acid etching group (8.83 ±3.63 MPa), while the lowest SBS values were observed in the control group (3.33 ±2.50 MPa). CONCLUSIONS: The additional roughening treatment applied to the PEEK surface increases the bond strength with heat-polymerized acrylic resin.

Effects of surface nanomorphology on the senescence of periodontal ligament stem cells.

OBJECTIVES: The effect of TiO2 nanotube morphology on the differentiation potency of senescent periodontal ligament stem cells was investigated. METHODS: Two types of titanium sheets with TiO2 nanotube morphology (20V-NT and 70V-NT) were prepared via anodic oxidation at 20 and 70 V separately, and their surface morphology was observed. Young periodontal ligament stem cells were cultivated in an osteogenic induction medium, and the most effective surface morphology in promoting osteogenic differentiation was selected. RO3306 and Nutlin-3a were used to induce the aging of young periodontal ligament stem cells, and senescent periodontal ligament stem cells were obtained. The osteogenic differentiation of senescent periodontal ligament stem cells was induced, and the effect of surface morphology on osteogenic differentiation was observed. RESULTS: Nanotube morphology was achieved on the surfaces of titanium sheets through anodic oxidation, and the diameters of the nanotubes increased with voltage. A significant difference in the effect of nanotube morphology was found among nanotubes with different diameters in the young periodontal ligament stem cells. The surface nanotube morphology of 20V-NT had a more significant effect that promoted osteogenic differentiation. Compared with a smooth titanium sheet, the surface nanotube morphology of 20V-NT increased the number of alkaline phosphatase-positive senescent periodontal ligament stem cells and promoted calcium deposition and the expression of osteogenic marker genes Runt-related transcription factor 2, osteopontin, and osteocalcin. CONCLUSIONS: A special nanotube morphology enhances the differentiation ability of senescent periodontal ligament stem cells, provides an effective method for periodontal regeneration, and further improves the performance of implants.

Evaluation of microstructure evolution and mechanical properties of Al-10Zn-1.63Si/Irvingia gabonensis particulates alloy composites.

This study demonstrates the feasibility of using Irvingia gabonensis shell particulates (IGSp) as alternative reinforcing materials in the development of aluminium-based composites. In this experimental study, the microstructure, phase composition, and mechanical behaviour of Al-10Zn-1.63Si/xIGSp (wt%, x = 1, 3, 5 and 7) composites were investigated. The Al-10Zn-1.63Si based composites were fabricated using the stir-casting technique. Different weight percentages (1, 3, 5 and 7) of IGSp were added to the Al-10Zn-1.63Si matrix. The chemical constituents of the IGSp were determined using X-ray fluorescence (XRF). The grain characteristics and phase(s) compositions were determined using Scanning Electron Microscopy (SEM) and X-ray diffractometer (XRD). The ultimate tensile strength, hardness, and impact strength of the developed composites were also determined. The SEM and XRD results revealed the presence of different phases: aluminium phosphate (Al16P16O64), gahnite (ZnAl2O4), andalusite (Al2SiO5), Quartz (SiO2) and aluminium silicate (Al2O3.5.SiO2). Results show that addition of IGSp led to an increase in ultimate tensile strength, with the highest value (128 MPa) obtained at 3 wt% IGSp. The hardness of the composites increased with increasing concentrations of IGSp, reaching a maximum value of 285 HV after adding 7 wt% IGSp. The impact strength improved with the addition of IGSp, with the highest value (30 J) obtained at 1 wt% IGSp. The improvements in mechanical properties were attributed to the dispersion of three major phases: aluminium silicate (Al2O3.54.SiO2), Al16P16O64 and Al2O3.54.SiO2. These phases contributed to the enhanced strength and hardness of the composites. The study noted a sudden decrease in ultimate tensile strength with higher concentrations of IGSp due to the increase in the intensities of Al16P16O64 and precipitation of hard but brittle new phase; Al2Si60.6O126.33. The study concludes that IGSp has the potential to serve as an alternative reinforcing material for aluminium-based composites.

Physical Characteristics of Sintered Silver Nanoparticle Inks with Different Sizes during Furnace Sintering.

The influence of nanoparticle (NP) size on the physical characteristics of sintered silver NP ink was studied using four different types of inks. The Ag NP inks were spin-coated on glass substrates with an average thickness of 300 nm. Each sample was sintered for 30 min, with temperatures from 50 °C to 400 °C by an interval of 50 °C. After sintering, the specific resistance of each case was obtained using the resistance and surface profile measurements. The minimum specific resistance obtained by the experiment was 2.6 µΩ·cm in the case in which 50 nm-sized Ag NP ink was sintered at 350 °C. The transformed surface morphology and grain size of each case were observed using scanning electron microscopy and atomic force microscopy. The results of this study can be a reference for future manufacturers in selecting the Ag NP size and the sintering temperature.

Exploring the Influence of Solvents on Electrochemically Etched Porous Silicon Based on Photoluminescence and Surface Morphology Analysis.

Porous silicon (PSi) has promising applications in optoelectronic devices due to its efficient photoluminescence (PL). This study systematically investigates the effects of various organic solvents and their concentrations during electrochemical etching on the resulting PL and surface morphology of PSi. Ethanol, n-butanol, ethylene glycol (EG) and N,N-dimethylformamide (DMF) were employed as solvents in hydrofluoric acid (HF)-based silicon etching. The PL peak position exhibited progressive blue-shifting with increasing ethanol and EG concentrations, accompanied by reductions in the secondary peak intensity and emission linewidth. Comparatively, changes in n-butanol concentration only slightly impacted the main PL peak position. Additionally, distinct morphological transitions were observed for different solvents, with ethanol and n-butanol facilitating uniform single-layer porous structures at higher concentrations in contrast to the excessive etching caused by EG and DMF resulting in PL quenching. These results highlight the complex interdependencies between solvent parameters such as polarity, volatility and viscosity in modulating PSi properties through their influence on surface wetting, diffusion and etching kinetics. The findings provide meaningful guidelines for selecting suitable solvent conditions to tune PSi characteristics for optimized device performance.

Thermal Transitions and Structural Characteristics of Poly(3,4-ethylenedioxythiophene/cucurbit[7]uril) Polypseudorotaxane and Polyrotaxane Thin Films.

Herein, we report the thermal transitions and structural properties of poly(3,4-ethylenedioxythiophene/cucurbit[7]uril) pseudopolyrotaxane (PEDOT∙CB7-PS) and polyrotaxane (PEDOT∙CB7-PR) thin films compared with those of pristine PEDOT. The structural characteristics were investigated by using variable-temperature spectroscopic ellipsometry (VTSE), differential scanning calorimetry (DSC), X-ray diffraction (XRD) and atomic force microscopy (AFM). VTSE and DSC results indicated the presence of an endothermic process and glass transition in the PEDOT∙CB7-PS and PEDOT∙CB7-PR thin films. X-ray diffraction of PEDOT∙CB7-PS and PEDOT∙CB7-PR powders displayed the presence of interchain π-π stacking revealing a characteristic arrangement of aromatic rings in the internal structure of the crystallites. AFM imaging of PEDOT∙CB7-PS and PEDOT∙CB7-PR thin films exhibited significant differences in the surface topographies compared with those of PEDOT. A high degree of crystallization was clearly visible on the surface of the PEDOT layer, whereas the PEDOT∙CB7-PS and PEDOT∙CB7-PR thin films exhibited more favorable surface parameters. Such significant differences identified in the surface morphology of the investigated layers can, therefore, be clearly associated with the presence of surrounding CB7 on PEDOT skeletons.

Novel microbial synthesis of titania nanoparticles using probiotic Bacillus coagulans and its role in enhancing the microhardness of glass ionomer restorative materials.

Dental caries is a commonly occurring non-communicable disease throughout the world that might compromise the quality of any individual's life. Glass ionomer cements (GIC) are the most acceptable restorative materials due to their ease of manipulation, minimal tooth loss and least invasive strategy; however, they lack mechanical stability that has become a point of concern. Nanoparticles (NPs) are an outstanding option for modifying and enhancing the properties of dental materials. The focus of this study was to prepare novel, biocompatible titania dioxide (TiO2) NPs as a dental-restorative material using an efficient probiotic Bacillus coagulans. The prepared NPs were incorporated into glass ionomer restorative material at varying concentrations and investigated for cell viability percentage, microhardness and surface morphology. Results indicated that pure 100% anatase phase TiO2 NPs with particle size of 21.84 nm arranged in smooth, spherical agglomerates and clusters forms. These NPs depicted cell viability > 90%, thus confirming their non-cytotoxic behavior. GIC restorative materials reinforced by 5% titania (TiO2) NPs demonstrated the highest microhardness in comparison to the control group and other experimental groups of the study. Surface morphology analysis revealed a reduction in cracks in this novel dental-restorative material supporting its compatible biological nature with better hardness strength and negligible crack propagation. Overall, these results indicated that TiO2 NPs produced using a biological approach could be easily used as restorative materials in dental applications.

Study on the influence of pore water pressure on shear mechanical properties and fracture surface morphology of sandstone.

To further investigate the weakening effect of pore water pressure on intact rock mechanics properties and characteristics of fracture surface after failure, direct shear tests of sandstone were conducted under different pore pressure. A 3D scanner was employed to digitize the morphology of the post-shear fracture surface. The variogram function was applied to quantify the anisotropic characteristics of post-shear fracture surface. The relationship between deformation during shear failure of intact rock and quantitative parameters of fracture surface after shear failure was initially established. It can be found that amplitudes of the sinusoidal surface determine the maximum value of variogram, and period affect lag distance that reach the maximum value of variogram. Test results revealed that the increase of pore pressure has obvious weakening effect on shear strength and deformation of rock. Moreover, the increase of pore pressure makes the shear fracture surface flatter. It can be obtained that both Sillmax and Rangemax are positively related to shear strain, but negatively related to normal strain.

Tunable evaporation-induced surface morphologies on chitosan film for light management.

The surface morphologies of polymer films have been used to improve the performance or enable new applications of films, such as controllable adhesion, shape morphing and light management. However, complicated and destructive methods were applied to produce surface morphologies on chitosan (CS) film. To overcome this challenge, we report an evaporation-induced self-assembly to form the tunable morphologies on the surface of short-chain chitosan film by varying the evaporation rates that influence the aggregation behavior of polymer chains between order and disorder. It enables the simple, tunable and scalable fabrication of surface morphologies on CS film (CS solution concentration: 2 wt%, drying from room temperature (RT) to 80 °C) that provides controllable haze (3-74 %) and high transmittance (>85 %) for the production of hazy and transparent window coatings. This simple approach to producing tunable surface morphologies could inspire the synthesis of multifunctional polymer films with different surface structures, whose applications can be extended to cell culture interfaces, flexible bioelectronic and optoelectronic devices.

A literature review of biomechanical studies on physiological and pathological sacroiliac joints: Articular surface structure, joint motion, dysfunction and treatments.

BACKGROUND: Sacroiliac joints are affected by mechanical environments; the joints are formed under mechanical stimulation, receive impact of walking between the upper and lower parts of the bodies and can be a cause of pain due to non-physiological loads. However, there are so far very few studies that reviewed biomechanics of physiological and pathological sacroiliac joints. This review article aims to describe the current sacroiliac joint biomechanics. METHODS: Previous original papers have been summarized based on three categories: articular surface structure, sacroiliac joint motion and sacroiliac joint dysfunction and treatments. FINDINGS: Although the articular surface morphologies vary greatly from individual to individual, many researchers have tried to classify the joints into several types. It has been suggested that the surface morphologies may not change regardless of joint dysfunction, however, the relationship between the joint structure and pain are still unclear. The range of sacroiliac joint motion is demonstrated to be less than 1 mm and there is no difference between physiological and pathological joints. The sacroiliac joint absorbs shock within the pelvis by the joint structures of pelvic morphology, ligaments and fat tissues. The morphology and motion of the sacroiliac joints may be optimized for upright bipedal walking. INTERPRETATION: There is no doubt that pelvic mechanical environments affect pain induction and treatment; however, no one has yet provided a concrete explanation. Future research could help develop treatments based on sacroiliac joint biomechanics to support joint function.

Magnetism-enhanced biomaterial Mg guide wire by MAP process for development of catheter insertion.

The surface topography of implant tools has indicated an interfacial contact in degradation still being discovered; however, the glossy texture of a tiny magnesium wire is important for absorbable medical devices. This paper investigated the alterations of surface quality by a magnetic abrasive polishing method using a rotational magnetic field-assisted system with input parameters of revolution, abrasive media, magnetic pole, flux density, vibration, and amplitude that could noticeably enhance asperities along a sample. Furthermore, the blood flow simulation is used to analyze flow within blood vessels while maintaining the surface roughness conditions of the guide wire. The results are compared and discussed. Magnetic field simulation is employed to investigate the magnetic field strength in the polishing zone. Scanning Electron Microscopy (SEM) provides visual aids for recognizing the differences between pre-and post-workpieces of magnesium wire. The experimental results reveal that a wire diameter of 0.50 mm predominantly achieves surface morphology from the initial roughness of 0.22 µm to 0.05 µm. The results corroborate that the distribution of blood in the circulatory system was relatively stable. Hence, this study establishes a crucial benchmark for the precision polishing of ultra-thin magnesium wires, which is vital for their use as high-precision biodegradable medical devices.