Sulfhydryl functionalized two-dimensional Ti3C2Tx MXene for efficient removal of Hg2+ in water samples.

This study describes an adsorption method for the removal of Hg2+ from aquatic environments using sulfhydryl-functionalized Ti3C2Tx (SH-Ti3C2Tx). SH-Ti3C2Tx materials were synthesized through covalent interactions between dithiothreitol and two-dimensional Ti3C2Tx. The insertion of -SH groups increased the interlayer spacing of Ti3C2Tx, resulting in a 3-fold increase in the specific surface area of SH-Ti3C2Tx compared with the original Ti3C2Tx. The maximum Hg2+ adsorption capacity of SH-Ti3C2Tx was 3042 mg/g, which was 2.3-fold greater than that of Ti3C2Tx. After Hg2+ adsorption, SH-Ti3C2Tx was regenerated for repeated used by rinsing with HCl-thiourea. Next, SH-Ti3C2Tx was loaded onto a melamine sponge to construct SH-Ti3C2Tx adsorption columns suitable for continuous flow Hg2+ removal with extremely low flow resistance. Hg2+ removal rates exceeded 95 % when treating both high and low-concentration solutions (20 mg/L Hg2+ and 10 µg/L Hg2+). This study demonstrates the excellent adsorption-regeneration performance of SH-Ti3C2Tx, which has broad application prospects for the in-situ treatment of water contaminated with Hg2+.

Ultralight Hierarchical Fe3O4/MoS2/rGO/Ti3C2Tx MXene Composite Aerogels for High-Efficiency Electromagnetic Wave Absorption.

Aerogel-based composites, renowned for their three-dimensional (3D) network architecture, are gaining increasing attention as lightweight electromagnetic (EM) wave absorbers. However, attaining high reflection loss, broad effective absorption bandwidth (EAB), and ultrathin thickness concurrently presents a formidable challenge, owing to the stringent demands for precise structural regulation and incorporation of magnetic/dielectric multicomponents with synergistic loss mechanisms within the 3D networks. In this study, we successfully synthesized a 3D hierarchical porous Fe3O4/MoS2/rGO/Ti3C2Tx MXene (FMGM) composite aerogel via directional freezing and subsequent heat treatment processes. Owing to their ingenious structure and multicomponent design, the FMGM aerogels, featured with abundant heterogeneous interface structure and magnetic/dielectric synergism, show exceptional impedance matching characteristics and diverse EM wave absorption mechanisms. After optimization, the prepared ultralight (6.4 mg cm-3) FMGM-2 aerogel exhibits outstanding EM wave absorption performance, achieving a minimal reflection loss of -66.92 dB at a thickness of 3.61 mm and an EAB of 6.08 GHz corresponding to the thickness of 2.3 mm, outperforming most of the previously reported aerogel-based absorbing materials. This research presents an effective strategy for fabricating lightweight, ultrathin, highly efficient, and broad band EM wave absorption materials.

Optimizing Light Dynamics: Designing A Ni-MOF Functionalized g-C3N4 Type II Heterostructure and a Ti3C2 MXene Schottky Junction for Efficient Photocatalytic H2 Production.

The photocatalytic production of hydrogen (H2) from water is a vital avenue towards sustainable energy and addressing global environmental challenges. To maximize efficiency, harnessing the synergistic effects of multiple co-catalysts is essential, as these interactions can significantly enhance performance. In this study, we introduce a ternary heterojunction composed of a nickel-imidazole framework (Ni-MOF), graphitic carbon nitride (CN), and Ti3C2 MXene (TC), employing solvothermal and wet impregnation methods, featuring a well-designed Type II heterojunction and a noble metal-free Schottky junction for efficient hydrogen evolution. The Type II heterojunction between Ni-MOF and CN minimizes charge carrier recombination and promotes photogenerated electron generation, while TC as an electron acceptor enhances electron capture, increases participation in surface reactions, and augments active sites. Consequently, the Ni-MOF/CN/TC hybrid catalyst achieves outstanding photocatalytic hydrogen evolution under visible light, with a peak production rate of 1044.46 µmol/g over 3 hours, surpassing CN by 13 fold and Ni-MOF/CN by 50%. This work provides insights into MXene-based ternary systems, emphasizing the potential for enhanced light absorption and efficient charge separation, making it a promising platform for photocatalytic applications.

Rational Design of Flexible, Self-Supporting, and Binder-Free Prussian White/KetjenBlack/MXene Composite Electrode for Sodium-Ion Batteries with Boosted Electrochemical Performance.

Due to their cost-effectiveness, abundant resources, and suitable working potential, sodium-ion batteries are anticipated to establish themselves as a leading technology in the realm of grid energy storage. However, sodium-ion batteries still encounter challenges, including issues related to low energy density and constrained cycling performance. In this study, a self-supported electrode composed of Prussian white/KetjenBlack/MXene (TK-PW) is proposed. In the TK-PW electrode, the MXene layer is coated with Prussian white nanoparticles and KetjenBlack with high conductivity, which is conducive to rapid Na+ dynamics and effectively alleviates the expansion of the electrode. Notably, the electrode preparation method is uncomplicated and economically efficient, enabling large-scale production. Electrochemical testing demonstrates that the TK-PW electrode retains 74.9% of capacity after 200 cycles, with a discharge capacity of 69.7 mAh·g-1 at 1000 mA·g-1. Furthermore, a full cell is constructed, employing a hard carbon anode and TK-PW cathode to validate the practical application potential of the TK-PW electrode.

Au-decorated Ti3C2Tx/porous carbon immunoplatform for ECM1 breast cancer biomarker detection with machine learning computation for predictive accuracy.

Electrochemical immunosensors, surpassing conventional diagnostics, exhibit significant potential for cancer biomarker detection. However, achieving a delicate balance between signal sensitivity and operational stability, especially at the heterostructure interface, is crucial for practical immunosensors. Herein, porous carbon (PC) integration with Ti3C2Tx-MXene (MX) and gold nanoparticles (Au NPs) constructs a versatile immunosensing platform for detecting extracellular matrix protein-1 (ECM1), a breast cancer-associated biomarker. The inclusion of PC provided robust structural support, enhancing electrolytic diffusion with an expansive surface area while synergistically facilitating charge transfer with Ti3C2Tx. The biosensor optimized with 1.0 mg PC demonstrates a robust electrochemical redox response to the surface-bound thionine (th) redox probe, utilizing an inhibition-based strategy for ECM1 detection. The robust antibody-antigen interactions across the PC-integrated Ti3C2Tx-Au NPs platform (MX-Au-C-1) enabled robust ECM1 detection within 0.1-7.5 nM, with a low limit of detection (LOD) of 0.012 nM. The constructed biosensor shows improved operational stability with a 98.6 % current retention over 1 h, surpassing MXene-integrated (MX-Au) and pristine Au NPs (63.2 % and 44.3 %, respectively) electrodes. Moreover, the successful adaptation of the artificial neural network (ANN) model for predictive analysis of the generated DPV data further validates the accuracy of the biosensor, promising its future application in AI-powered remote health monitoring.

Ultrasensitive electrochemical microRNA-21 detection based on MXene and ATRP photocatalytic strategy.

A Ti3C2TxMXene-based biosensor has been developed and the photocatalytic atom transfer radical polymerization (photo ATRP) amplification strategy applied to detect target miRNA-21 (tRNA). Initially, Ti3C2TxMXene nanosheets were synthesized from the Ti3AlC2 MAX precursor via selective aluminum etching. Then, functionalization of Ti3C2TxMXene nanosheets with 3-aminopropyl triethoxysilane (APTES) via silylation reactions to facilitate covalent bonding with hairpin DNA biomolecules specifically designed for tRNA detection. Upon binding with the tRNA, the hairpin DNA liberated the azide (N3) group, initiating a click reaction to affix to the photo ATRP initiator. Through the ATRP photoreaction, facilitated by an organic photoredox catalyst and light, a significant amount of ferrocenyl methyl methacrylate (FMMA) monomer was immobilized on the electrode. Therefore, the electrochemical signal is amplified. The electrochemical efficacy of the biosensor was assessed using square wave voltammetry (SWV). Under optimized conditions, the biosensor demonstrated remarkable sensitivity in detecting tRNA, with a linear detection range from 0.01 fM to 10 pM and a detection limit of 2.81 aM. The findings elucidate that the developed biosensor, in conjunction with the photo ATRP strategy, offers reproducibility, stability, and increased sensitivity, underscoring its potential applications within the experimental medical sector of the biomolecular industry.

Facile Fabrication of Titanium Carbide (Ti3C2)-Bismuth Vanadate (BiVO4) Nano-Coupled Oxides for Anti-cancer Activity.

Background MXene is a newly discovered substance consisting of 2D transition metal carbides or nitrides, produced through the disintegration and etching of aluminum layers. It possesses numerous properties, including a high surface area, conductivity, strength, stiffness, negative zeta potential, and excellent volumetric capacitance. MXene is utilized in detecting anti-cancer medicine, while bismuth vanadate (BiVO4) is synthesized to form an optimized material for anti-cancer activity applications. BiVO4 exhibits visible light absorption, strong chemical stability, and non-toxic properties. However, when loaded onto target stem cells, it can cause skin and respiratory irritation. Aim This study aimed to evaluate the facile fabrication of titanium carbide (Ti3C2)-BiVO4 nanomaterials coupled with oxides for anti-cancer activity. Moreover, it aimed to create Ti3C2-BiVO4 nanomaterials in combination with oxides using X-ray diffraction (XRD) and scanning electron microscopy (SEM) to assess their potential as efficient and targeted anti-cancer agents. Methods and materials To prepare the 2D Ti3C2 MXene, 2.5 g of titanium aluminum carbide (Ti3AlC2) powder was dissolved in 60 mL of a 40% hydrofluoric acid (HF) solution in a polytetrafluoroethylene(PTFE) container. The etching process was made more efficient and completed in 24 hours by using a magnetic stirring system to keep the mixture stirred and heated continuously. The centrifugation was performed at 4000 rpm for five minutes. Subsequently, deionized water was used to wash the solution many times until its pH reached around 7. The appropriate Ti3C2 powder was made by vacuum drying the acquired sediment at 80°C for 24 hours. Monoclinic BiVO4 samples were synthesized via a hydrothermal method. Typically, 10 mmol of Bi(NO3)3.5H2O was dissolved in 100 mL of a 2 mol/L HNO3 solution and stirred uniformly. Subsequently, 10 mmol of ammonium metavanadate (NH4VO3) was added to the mixed solution. After being stirred for one hour, the mixture was transferred into a 100 mL sealed Teflon-lined stainless steel autoclave at 180°C for 16 hours. After cooling to room temperature, the sediment was washed three times with deionized water, ethanol, and acetone, respectively. Finally, the suspension was dried at 80°C, followed by calcination at 450°C for three hours to obtain BiVO4. Ti3C2-BiVO4 heterostructures were prepared by surface modification Ti3C2 using BiVO4 suspensions by a simple, cost-effective approach. Results Ti3C2 nanosheets were observed with BiVO4 particles, and the high crystalline nature of the compound was confirmed after XRD analysis and energy-dispersive spectroscopy (EDS) analysis. The compound was found to be pure without any impurities and exhibited anti-cancer activity. Conclusion The XRD, field emission scanning electron microscopy(FESEM), and EDS investigations provide an in-depth analysis of the structural, morphological, and compositional characteristics of Ti3C2-BiVO4 sheets. The XRD analysis proves the successful combination of different materials and the presence of crystalline phases. The FESEM imaging technique exposes the shape and arrangement of particles in sheets, while the EDS analysis verifies the elemental composition and uniform distribution. These investigations show that Ti3C2-BiVO4 composites have been successfully synthesized, indicating their potential for use in anti-cancer applications.

Microwave-Assisted Efficient Intercalation for Fast Fabrication of High-Quality and Large-Size Single-Layer Ti3C2Tx Nanosheets.

A novel microwave-assisted intercalation (MAI) strategy is proposed for fast and efficient intercalation of layered MXene to prepare large-size single-layer MXene. After LiF-HCl etching of Ti3AlC2, the as-prepared multi-layer Ti3C2Tx (M-T) are intercalated with Li3AlF6 as an intercalator and ethylene glycol (EG) as a solvent under microwave irradiation for 5 min. Furthermore, the dispersed high-quality large-sized single-layer Ti3C2Tx (S-T) nanosheets with a thickness of 1.66 nm and a large lateral size over 20 µm are achieved with a yield of over 60% after a further ultrasonic delamination followed by electrostatic precipitation, acid washing, and calcination. In addition, Pd/S-T composite catalyst, which is constructed with Pd nanoparticles supported on the as-prepared S-T nanosheets, exhibits an excellent performance for rapid and efficient selective hydrogenation of nitroarenes with H2 under a mild condition. At room temperature, full conversion of nitrobenzene and 100% aniline selectivity are achieved over Pd/S-T catalyst in 20 min with 0.5 MPa of H2 pressure. This work provides a novel method for facile, fast, and large-scale preparation of single-layer MXene and develops a new approach for constructing efficient nanocatalytic systems.

Aptamer-Functionalized Magnetic Ti3C2 Based Nanoplatform for Simultaneous Enrichment and Detection of Exosomes.

Exosomes are nanovesicles secreted by cells, which play a crucial role in various pathological processes. Exosomes have shown great promise as tumor biomarkers because of the abundant secretion during tumor formation. The development of a convenient, efficient, and cost-effective method for simultaneously enriching and detecting exosomes is of utmost importance for both basic research and clinical applications. In this study, an aptamer-functionalized magnetic Ti3C2 composite material (Fe3O4@Ti3C2@PEI@DSP@aptamer@FAM-ssDNA) is prepared for the simultaneous enrichment and detection of exosomes. CD63 aptamers are utilized to recognize and capture the exosomes, followed by magnetic separation. The exosomes are then released by cleaving the disulfide bonds of DSP. Compared to traditional methods, Fe3O4@Ti3C2@PEI@DSP@aptamer@FAM-ssDNA exhibited superior efficiency in enriching exosomes while preserving their structural and functional integrity. Detection of exosome concentration is achieved through the fluorescence quenching of Ti3C2 and the competitive binding between the exosomes and a fluorescently labeled probe. This method exhibited a low detection limit of 4.21 × 104 particles mL-1, a number that is comparable to the state-of-the-art method in the detection of exosomes. The present study demonstrates a method of simultaneous enrichment and detection of exosomes with a high sensitivity, accuracy, specificity, and cost-effectiveness providing significant potential for clinical research and diagnosis.

CuxO decorated Ti3C2Tx MXene composites for non-enzymatic glucose sensing with large linear ranges.

Ti3C2Tx MXene/CuxO composites were prepared by acid etching combined with electrochemical technique. The abundant active sites on the surface of MXene greatly increase the loading of CuxO nanoparticles, and the synergistic effect between the different components of the composite can accelerate the oxidation reaction of glucose. The results indicate that at the working potential of 0.55 V (vs. Ag/AgCl), the glucose sensor based on Ti3C2Tx MXene/CuxO composite presents large linear concentration ranges from 1 µM to 4.655 mM (sensitivity of 361 µA mM-1 cm-2) and from 5.155 mM to 16.155 mM (sensitivity of 133 µA mM-1 cm-2). The limit of detection is 0.065 µM. In addition, the sensor effectively avoids the oxidative interference of common interfering species such as ascorbic acid, dopamine and uric acid. The sensor has good reproducibility, stability and acceptable recoveries for the detection of glucose in human sweat sample (97.5-103.3%) with RSD values less than 4%. Based on these excellent properties it has great potential for the detection of glucose in real samples.

Epitaxial Growth of the Large-Scale, Highly-Ordered 3D GaN-Truncated Pyramid Array Toward an Ultrahigh Rejection Ratio and Responsivity Visible-Blind Ultraviolet Photodetection.

The micro- and nanostructures of III-nitride semiconductors captivate strong interest owing to their distinctive properties and myriad potential applications. Nevertheless, challenges endure in managing the damage inflicted on crystals through top-down processes or achieving extensive control over the large-area growth of these microstructures via bottom-up methods, thereby impacting their optical and electronic properties. Here, we present novel epitaxially grown 3D GaN truncated pyramid arrays (TPAs) on patterned Si substrates, devoid of any catalyst. These GaN TPAs feature highly ordered, large-scale structures, attributed to the utilization of 3D Si substrates and thin AlN interlayers to alleviate epitaxial strains and limit dislocation formation. Comprehensive characterization via scanning electron microscopy, transmission electron microscopy, Raman spectroscopy, and cathodoluminescence attests to the superior structural and optical attributes of these crystals. Furthermore, photoluminescence and ultraviolet (UV)-visible diffuse reflectance spectroscopy reveal sharp band-edge emission and significant light trapping in the UV bands. Employing these GaN TPAs, we constructed metal-semiconductor-metal visible-blind UV photodetectors (PDs) incorporating Ti3C2 MXene as Schottky electrodes. These PDs display exceptional responsivity, achieving 5.32 × 103 mA/W at 255 nm and an ultrahigh UV/visible rejection ratio (R255nm/R450nm) approaching 106, which are 1-2 orders of magnitude higher than most recently reported works. This exploration showcases novel GaN-based microstructures characterized by uniformity, ordered geometry, and exemplary crystalline integrity, paving the way for developing optoelectronic applications.

Stretchable Piezoresistive Pressure Sensor Array with Sophisticated Sensitivity, Strain-Insensitivity, and Reproducibility.

This study delves into the development of a novel 10 by 10 sensor array featuring 100 pressure sensor pixels, achieving remarkable sensitivity up to 888.79 kPa-1, through the innovative design of sensor structure. The critical challenge of strain sensitivity inherent is addressed in stretchable piezoresistive pressure sensors, a domain that has seen significant interest due to their potential for practical applications. This approach involves synthesizing and electrospinning polybutadiene-urethane (PBU), a reversible cross-linking polymer, subsequently coated with MXene nanosheets to create a conductive fabric. This fabrication technique strategically enhances sensor sensitivity by minimizing initial current values and incorporating semi-cylindrical electrodes with Ag nanowires (AgNWs) selectively coated for optimal conductivity. The application of a pre-strain method to electrode construction ensures strain immunity, preserving the sensor's electrical properties under expansion. The sensor array demonstrated remarkable sensitivity by consistently detecting even subtle airflow from an air gun in a wind sensing test, while a novel deep learning methodology significantly enhanced the long-term sensing accuracy of polymer-based stretchable mechanical sensors, marking a major advancement in sensor technology. This research presents a significant step forward in enhancing the reliability and performance of stretchable piezoresistive pressure sensors, offering a comprehensive solution to their current limitations.

Harnessing Holey MXene/Graphene Oxide Heterostructure to Maximize Ion Channels in Lamellar Film for High-Performance Capacitive Deionization.

2D Ti3C2Tx MXene-based film electrodes with metallic conductivity and high pseudo-capacitance are of considerable interest in cutting-edge research of capacitive deionization (CDI). Further advancement in practical use is however impeded by their intrinsic limitations, e.g., tortuous ion diffusion pathway of layered stacking, vulnerable chemical stability, and swelling-prone nature of hydrophilic MXene nanosheet in aqueous environment. Herein, a nanoporous 2D/2D heterostructure strategy is established to leverage both merits of holey MXene (HMX) and holey graphene oxide (HGO) nanosheets, which optimize ion transport shortcuts, alleviate common restacking issues, and improve film's mechanical and chemical stability. In this design, the nanosized in-plane holes in both handpicked building blocks build up ion diffusion shortcuts in the composite laminates to accelerate the transport and storage of ions. As a direct outcome, the HMX/rHGO films exhibit remarkable desalination capacity of 57.91 mg g-1 and long-term stability in 500 mg L-1 NaCl solution at 1.2 V. Moreover, molecular dynamics simulations and ex situ wide angle X-ray scattering jointly demonstrate that the conductive 2D/2D networks and ultra-short ion diffusion channels play critical roles in the ion intercalation/deintercalation process of HMX/rHGO films. The study paves an alternative design concept of freestanding CDI electrodes with superior ion transport efficiency.

Enrichment and detection of polycyclic aromatic hydrocarbon in tea and coffee using phenyl-functionalized NiFe2O4@Ti3C2TX based magnetic solid-phase extraction.

Polycyclic aromatic hydrocarbons (PAHs) are commonly found in various environmental matrices and have received significant attention due to their toxic effects on ecosystems and environmental health. In this study, a specific magnetic composite material derived from MXene, known as phenyl-functionalized NiFe2O4@Ti3C2TX, was designed and synthesized using a simple method. This composite material was used to develop an effective magnetic solid-phase extraction (MSPE) method for enriching trace polycyclic aromatic hydrocarbons (PAHs) in tea and coffee samples. The eluted PAHs were analyzed via gas chromatography-tandem mass spectrometry. Under optimal conditions, this method exhibited excellent linear relationships for 16 PAHs within the ranges of 0.001-25 and 0.0005-25 µg/L, with correlation coefficients exceeding 0.9979. The limits of detection for the target PAHs ranged from 0.1 to 0.3 ng/L. The effectiveness of the proposed method was evaluated by analyzing tea and coffee samples, and the satisfactory spiked recoveries of PAHs ranged from 84.5% to 112.6%.

Maintaining the 2D Structure of MXene via Self-Assembled Monolayers for Efficient Lubrication in High Humidity.

MXene is considered as a promising solid lubricant due to facile shearing ability and tuneable surface chemistry. However, it faces challenges in high-humidity environments where excessive water molecules can significantly impact its 2D structure, thus deteriorating its lubricating properties. In this work, the self-assembled monolayers are formed on MXene by surface chlorination (MXene-Cl) and fluorination (MXene-F), and their friction behaviors in high/low humidity are investigated. The results indicate that MXene-F and MXene-Cl can maintain a relatively constant friction coefficient (CoF) (MXene-F ∼0.76, MXene-Cl ∼0.48) under both high (75%) and low (25%)-relative humidity (RH) environments. Meanwhile, the MXene-F and MXene-Cl display a lower CoF than the pristine MXene (MXene CoF∼1.18) in high humidity. The above phenomena are mainly attributed to the preservation of its 2D layered structure, the increased layer spacing, and superficial partial oxidation for SAMs-functionalized MXene under high humidity during friction. Interestingly, MXene-Cl with moderate water resistance has a lower CoF than that of MXene-F with complete water resistance. The nanostructured water adsorption capacity and larger interlayer spacing of MXene-Cl make it exhibit a lower CoF compared to MXene-F. The findings of this study offer valuable guidance for tailoring MXene by surface chemical functionalization as an efficient solid lubricant in high humidity.

Transient paper-based electrochemical biosensor Fabricated by superadditive Cu-TCPP(Fe)/Mxene for Multipathway non-invasive, highly sensitive detection of Bodily metabolites.

Current advances in non-invasive fluid diagnostics highlight unique benefits for monitoring metabolic diseases. However, the low concentrations and complex compositions of biomarkers in fluids such as sweat, urine, and saliva impose stringent demands on the sensitivity and stability of detection technologies. Here, we developed a high-sensitivity, low-cost instantaneous electrochemical sensor based on the superadditive effect mechanism of Cu-TCPP(Fe)/Mxene (MMs Paper-ECL Sensor), which has been successfully applied for the simultaneous real-time detection of glucose and uric acid. Strong interfacial interactions between Mxene and Cu-TCPP(Fe) were revealed through precise simulation calculations and multi-dimensional characterization analysis, significantly enhancing the sensor's electrocatalytic performance and reaction kinetics. Experimentally, this exceptional electrocatalytic activity was demonstrated in its unprecedented high sensitivity and wide linear detection range for glucose and uric acid, with a non-invasive linear range from 0.001 nM to 5 mM, 0.025 nM-5 mM, detection limits as low as 1.88 aM and 5.80 pM, and stability extending up to 100 days. This represents not only a breakthrough in sensitivity and stability but also provides an effective, low-cost solution that overcomes the limitations of existing electronic devices, enabling multi-channel simultaneous detection. The universality of this sensor holds vast potential for application in the field of non-invasive fluid diagnostics.

A bulit-in self-calibration ratiometric self-powered photoelectrochemical sensor for high-precision and sensitive detection of microcystin-RR.

A novel high-precision aptasensor of microcystin-RR (MC-RR) is developed based on a ratiometric self-powered photoelectrochemical platform. In detail, the defective MoS2/Ti3C2 nanocomposite with good photoelectric activity was designed to serve as the photoanode of the sensor for enhancing the signal and improving the detection sensitivity. In order to effectively eliminate external interferences, the key point of this ratiometric device is the introduction of the spatial-resolved technique, which includes the detection section and the reference section, generating reference signals and response signals, respectively. Moreover, output power was used as the detection signal, instead of the traditional photocurrent or photovoltage. Further, potassium persulfate was introduced as electron acceptor, which was beneficial for improving the electron transport efficiency, hindering electron-hole recombination, and significantly promoting the performance of the sensor. Finally, aptamer was adopted as recognition element to capture MC-RR molecules. The prepared sensor had a linear range from 10-12 to 10-6 M, and the detection limit was 5.6 × 10-13 M (S/N = 3). It has good precision, selectivity, and sensitivity, which shows great prospects in the on-site accurate analysis of samples with high energy output in the self-powered sensing field.

Remediation of Safranin-O and Acid Fuchsin by Using Ti3C2 MXene /rGo-Cu2O Nanocomposite: Preparation, Characterization, Isotherm, Kinetics and Thermodynamic Studies.

In recent years, MXene has become one of the most intriguing two-dimensional layered (2Dl) materials extensively explored for various applications. In this study, a Ti3C2 MXene/rGo-Cu2O Nanocomposite (TGCNCs) was developed to eliminate Safranin-O effectively (SO) and Acid Fuchsin (AF) as cationic dyes from the aquatic environment. Multistep was involved in the preparation of the adsorbent system, including the Preparation of Ti3C2, after that, GO synthesis by the Humer method, followed by rGO production, then added CuSO4 to obtain a final Nanocomposite (NCs) called "TGCNCs". The structure of TGCNCs can be varied in several ways, including FTIR, SEM, TGA, Zeta, EDX, XRD, and BET, to affirm the efficacious preparation of TGCNCs. A novel adsorbent system was developed to remove SO and AF, both cationic dyes. Various adsorption conditions have been optimized through batch adsorption tests, including the pH of the solution (4-12), the effect of dosage (0.003-0.03 g), the impact of the contact time (5-30 min), and the effect of beginning dye concentration (25-250 mg/L). Accordingly, the TGCNCs exhibited excellent fitting for Freundlich isotherm mode, resulting in maximum AF and SO adsorption capacities of 909.09 and 769.23 mg.g-1. This research on adsorption kinetics suggests that a pseudo-second-order (PSO) model would fit well with the experimental data ( = 0.998 and = 0.990). It is evident from the thermodynamic parameters that adsorption is an endothermic process that is spontaneous and favourable. During the adsorption of SO and AF onto NCs, it is hypothesized that these molecules interact intramolecularly through stacking interactions, H-bond interactions, electrostatic interactions, and entrapment within the polymeric Poros structure nanocomposite. Regeneration studies lasting up to five cycles were the most effective for both organic dyes under study.

Tailoring Oxygen-Depleted and Unitary Ti3C2T x Surface Terminals by Molten Salt Electrochemical Etching Enables Dendrite-Free Stable Zn Metal Anode.

Two-dimensional Ti3C2Tx MXene materials, with metal-like conductivities and versatile terminals, have been considered to be promising surface modification materials for Zn-metal-based aqueous batteries (ZABs). However, the oxygen-rich and hybridized terminations caused by conventional methods limit their advantages in inhibiting zinc dendrite growth and reducing corrosion-related side reactions. Herein, -O-depleted, -Cl-terminated Ti3C2Tx was precisely fabricated by the molten salt electrochemical etching of Ti3AlC2, and controlled in-situ terminal replacement from -Cl to unitary -S or -Se was achieved. The as-prepared -O-depleted and unitary-terminal Ti3C2Tx as Zn anode coatings provided excellent hydrophobicity and enriched zinc-ionophilic sites, facilitating Zn2+ horizontal transport for homogeneous deposition and effectively suppressing water-induced side reactions. The as-assembled Ti3C2Sx@Zn symmetric cell achieved a cycle life of up to 4200 h at a current density and areal capacity of 2 mA cm-2 and 1 mAh cm-2, respectively, with an impressive cumulative capacity of up to 7.25 Ah cm-2 at 5 mA cm-2 // 2 mAh cm-2. These findings provide an effective electrochemical strategy for tailoring -O-depleted and unitary Ti3C2Tx surface terminals and advancing the understanding of the role of specific Ti3C2Tx surface chemistry in regulating the plating/stripping behaviors of metal ions.

Covalent Bonding of MXene/COF Heterojunction for Ultralong Cycling Li-Ion Battery Electrodes.

Covalent organic frameworks (COFs) have emerged as promising renewable electrode materials for LIBs and gained significant attention, but their capacity has been limited by the densely packed 2D layer structures, low active site availability, and poor electronic conductivity. Combining COFs with high-conductivity MXenes is an effective strategy to enhance their electrochemical performance. Nevertheless, simply gluing them without conformal growth and covalent linkage restricts the number of redox-active sites and the structural stability of the composite. Therefore, in this study, a covalently assembled 3D COF on Ti3C2 MXenes (Ti3C2@COF) is synthesized and serves as an ultralong cycling electrode material for LIBs. Due to the covalent bonding between the COF and Ti3C2, the Ti3C2@COF composite exhibits excellent stability, good conductivity, and a unique 3D cavity structure that enables stable Li+ storage and rapid ion transport. As a result, the Ti3C2-supported 3D COF nanosheets deliver a high specific capacity of 490 mAh g-1 at 0.1 A g-1, along with an ultralong cyclability of 10,000 cycles at 1 A g-1. This work may inspire a wide range of 3D COF designs for high-performance electrode materials.