Synthesis and characterization of enhanced azo-azomethine doped PANI/HCl conducting polymers for electrochemical applications.

In this study, conducting polymers composed of polyaniline hydrochloric acid (PANI/HCl) with varying concentrations of a newly synthesized azo-azomethine dye (4-(((Z)-2-hydroxy-5-((Z)-(4-hydroxyphenyl)diazenyl)-3-methoxybenzylidene)amino)benzoic acid) were synthesized using a chemical oxidative polymerization technique. The synthesized azo-azomethine was characterized by FTIR, 1H-NMR, 13C-NMR, and HRMS. The effects of varying the concentration of the dopant azo-azomethine in PANI/HCl on its optical, structural, thermal, and electrical properties were examined using FTIR, UV-Vis, XRD, FESEM, TEM, cyclic voltammetry, and electrical impedance spectra. The results indicate that the optical, direct, and indirect band gaps of the doped polymers decreased from 4.48 and 3.96 eV to 3.91 and 2.49 eV, respectively. The crystalline structure and phase transitions in the doped polymers were examined using X-ray diffraction. Cyclic voltammetry demonstrated that the doped polymers exhibited higher electrochemical conductivity compared to the pure polymer, with the specific capacitance increasing from 161.17 to 816.9 F/g. The electrical impedance spectra revealed the bulk resistance and conductivity of the material. Among all the doped polymers, PANI/HCl with an azo-azomethine concentration of 5 × 10-5 M exhibited lower bulk resistance (10 Ω) and higher electrical conductivity (σ = 50.09 × 10-3 S cm-1).

Microporous tungsten oxide spheres coupled with Ti3C2Txnanosheets for high-volumetric capacitance supercapacitors.

In the contemporary landscape of technological advancements, the burgeoning demand for portable electronics and flexible wearable devices has necessitated the development of energy storage systems with superior volumetric performance. Tungsten oxide (WO3), known for its high density and theoretical capacitance, is a promising electrode material for supercapacitors. However, low conductivity and poor cycling stability are still the key bottlenecks for its application. Herein, a novel composite comprising hollow porous WO3 spheres (HPWS) derived by template method was electrostatic self-assembled on the surface of the Ti3C2Tx nanosheets. The resulting electrodes exhibited ultra-high volumetric capacitance of 1930 F cm-3 at 1 A g-1 and rate capability of 46% at 50 A g-1, attributed to enhanced ion accessibility from microporous structure and electron transport from conductive network of Ti3C2Tx even at a high packing density of 3.86 g cm-3. Utilizing HPWS/Ti3C2Tx as the negative electrode and porous carbon as the positive electrode, the assembled asymmetric supercapacitor achieved an energy density of 31 Wh kg-1 at a power density of 650 W kg-1 with over 107% capacitance retention after 5000 cycles. This work provides a promising approach for developing next-generation supercapacitors with ultra-high volumetric capacitance.

Understanding the Electric Double Layer at the Electrode-Electrolyte Interface: Part I - No Ion Specific Adsorption.

We present a comprehensive mean-field model that takes into account the key components of modern electrical double layer theory at the interface between an electrode and an electrolyte solution. The model considers short-range specific interactions between different species, including electrode-ion repulsion, the hydration of ions, dielectric saturation of solvent (water), and excluded volume (steric) interactions between species. By solving a modified Poisson-Boltzmann equation and using the appropriate results of quantum chemistry calculations on the hydration of ions, we can accurately approximate the differential capacitance profiles of aqueous electrolyte solutions at the boundary with a silver electrode. The specific interactions between the ions and the electrodes in the systems under consideration are assumed to be significantly weaker than their Coulomb interactions. A novel aspect of our research is the investigation of the impact of short-range ion-water interactions on the differential capacitance, which provides new insights into the behavior of the electrical double layer. This model holds the potential to be useful for electrochemical engineers working on the development of supercapacitors and related electrochemical energy storage devices. It serves as a basis for future modeling of electrolyte systems on real electrodes, especially in scenarios where chemical ion-electrode interactions are significant.

Thin-Film Transistor Digital Microfluidics Circuit Design with Capacitance-Based Droplet Sensing.

With the continuous expansion of pixel arrays in digital microfluidics (DMF) chips, precise droplet control has emerged as a critical issue requiring detailed consideration. This paper proposes a novel capacitance-based droplet sensing system for thin-film transistor DMF. The proposed circuit features a distinctive inner and outer dual-pixel electrode structure, integrating droplet driving and sensing functionalities. Discharge occurs exclusively at the inner electrode during droplet sensing, effectively addressing droplet perturbation in existing sensing circuits. The circuit employs a novel fan-shaped structure of thin-film transistors. Simulation results show that it can provide a 48 V pixel voltage and demonstrate a sensing voltage difference of over 10 V between deionized water and silicone oil, illustrating its proficiency in droplet driving and accurate sensing. The stability of threshold voltage drift and temperature was also verified for the circuit. The design is tailored for integration into active matrix electrowetting-on-dielectric (AM-EWOD) chips, offering a novel approach to achieve precise closed-loop control of droplets.

Hybrid TiO2-RGO nanocomposite as high specific capacitance electrode for supercapacitor.

This study describes the fabrication of composite electrodes comprising TiO2and reduced graphene oxide layers using a moderate-temperature hydrothermal method. The morphology, crystalline structure, chemical composition, and optical features of the prepared composites were analyzed by FE-SEM, x-ray diffraction, FTIR, and UV-visible spectroscopy. The cyclic voltammetry (CV) and Nyquist plots were used to assess the electrochemical and impedance responses of the composite electrodes, respectively. The analysis revealed that the incorporation of RGO reduced the TiO2bandgap to 3.87 eV 3.02 eV and improved the specific capacitance, enhancing the TiO2-RGO electrode's supercapacitive performance. CV studies highlight that the TiO2-RGO composite has a high specific capacitance of 152 F g-1at a substantially faster scan rate of 25 mV s-1in a 1.0 M-KOH dilute electrolyte. These findings confirmed the applicability of the fabricated electrodes as prospective supercapacitor electrodes.

WSe2 Negative Capacitance Field-Effect Transistor for Biosensing Applications.

Field-effect transistor (FET) biosensors based on two-dimensional (2D) materials are highly sought after for their high sensitivity, label-free detection, fast response, and ease of on-chip integration. However, the subthreshold swing (SS) of FETs is constrained by the Boltzmann limit and cannot fall below 60 mV/dec, hindering sensor sensitivity enhancement. Additionally, the gate-leakage current of 2D material biosensors in liquid environments significantly increases, adversely affecting the detection accuracy and stability. Based on the principle of negative capacitance, this paper presents for the first time a two-dimensional material WSe2 negative capacitance field-effect transistor (NCFET) with a minimum subthreshold swing of 56 mV/dec in aqueous solution. The NCFET shows a significantly improved biosensor function. The pH detection sensitivity of the NCFET biosensor reaches 994 pH-1, nearly an order of magnitude higher than that of the traditional two-dimensional WSe2 FET biosensor. The Al2O3/HfZrO (HZO) bilayer dielectric in the NCFET not only contributes to negative capacitance characteristics in solution but also significantly reduces the leakage in solution. Utilizing an enzyme catalysis method, the WSe2 NCFET biosensor demonstrates a specific detection of glucose molecules, achieving a high sensitivity of 4800 A/A in a 5 mM glucose solution and a low detection limit (10-9 M). Further experiments also exhibit the ability of the biosensor to detect glucose in sweat.

Exploring the Electrochemical Performance of Molybdenum Disulfide Nanoparticles Entrenched in Miscible Poly(methyl methacrylate)-Poly(lactic acid) Blends as Freestanding Electrodes for Supercapacitors.

The focus of the study in this article is analyzing the electrochemical properties of molybdenum disulfide on miscible poly(methyl methacrylate)-poly(lactic acid) blends for supercapacitors. The interaction between molybdenum disulfide and miscible poly(methyl methacrylate)-poly(lactic acid) blends, affinity toward water, surface morphology, and mechanical properties are inspected by Fourier transform infrared spectroscopy, water contact angle, scanning electron microscopy, and universal testing machine, respectively. Among the developed membranes, 0.75 wt% of molybdenum disulfide on poly(methyl methacrylate)-poly(lactic acid) shows better electrochemical performances. It exhibits a maximum specific capacitance of 255.5 F g-1 at a current density of 1.00 mA g-1, maximum energy density of 22.7 Wh kg-1, and maximum power density of 360 W kg-1. A cycle study reveals 92% capacitance retention after 2500 cycles. The designed supercapacitor device shows a maximum specific capacitance of 1240 µF g-1 at a current density of 0.5 µA g-1, maximum energy density of 43 µWh kg-1, and maximum power density of 700 µW kg-1. Flexible membranes of molybdenum disulfide are expected to be a potent combination for supercapacitor applications.

Dynamin-2 mutations linked to neonatal-onset centronuclear myopathy impair exocytosis and endocytosis in adrenal chromaffin cells.

Dynamins are large GTPases whose primary function is not only to catalyze membrane scission during endocytosis but also to modulate other cellular processes, such as actin polymerization and vesicle trafficking. Recently, we reported that centronuclear myopathy associated dynamin-2 mutations, p.A618T, and p.S619L, impair Ca2+-induced exocytosis of the glucose transporter GLUT4 containing vesicles in immortalized human myoblasts. As exocytosis and endocytosis occur within rapid timescales, here we applied high-temporal resolution techniques, such as patch-clamp capacitance measurements and carbon-fiber amperometry to assess the effects of these mutations on these two cellular processes, using bovine chromaffin cells as a study model. We found that the expression of any of these dynamin-2 mutants inhibits a dynamin and F-actin-dependent form of fast endocytosis triggered by single action potential stimulus, as well as inhibits a slow compensatory endocytosis induced by 500 ms square depolarization. Both dynamin-2 mutants further reduced the exocytosis induced by 500 ms depolarizations, and the frequency of release events and the recruitment of neuropeptide Y (NPY)-labeled vesicles to the cell cortex after stimulation of nicotinic acetylcholine receptors with 1,1-dimethyl-4-phenyl piperazine iodide (DMPP). They also provoked a significant decrease in the Ca2+-induced formation of new actin filaments in permeabilized chromaffin cells. In summary, our results indicate that the centronuclear myopathy (CNM)-linked p.A618T and p.S619L mutations in dynamin-2 affect exocytosis and endocytosis, being the disruption of F-actin dynamics a possible explanation for these results. These impaired cellular processes might underlie the pathogenic mechanisms associated with these mutations.

Conversion of high moisture biomass to hierarchical porous carbon via molten base carbonisation and activation for electrochemical double layer capacitor.

Biomass-derived carbon for supercapacitors faces the challenge of achieving hierarchical porous carbon with graphitic structure and specific heteroatoms through a single-stage thermal process that minimises resource input. Herein, molten base carbonisation and activation is proposed. The process utilises the inherent moisture of Moso bamboo shoots, coupled with a low amount of KOH, to form potassium organic salts before drying. The resultant potassium salts promote in-situ activation during single-stage heating process, yielding hierarchical porous, large specific surface area, and partially graphitised carbon with heteroatoms (N, O). As an electrode material, this carbon exhibits a specific capacitance of 327F g-1 in 6 M KOH and 182F g-1 in 1 M TEABF4/AN, demonstrating excellent cycling stability over 10,000 cycles at 2 A/g. Overall, this study presents a straightforward process that avoids pre-drying of biomass, minimises base consumption, and employs single-stage heating to fabricate electrode carbon suitable for supercapacitors.

Water relations and photosystem II efficiency of the intertidal macroalga Fucus virsoides.

Intertidal macroalgae are sessile poikilohydric organisms exposed to desiccation stress during emersion. Water relations parameters are useful tools to evaluate an organism's capacity to withstand water scarcity conditions, but such information on marine intertidal macroalgae is scarce. We assessed the water relations of the intertidal relict Fucus virsoides, the unique Fucus species endemic to the Mediterranean. We combined measurements of water potential (Ψ) parameters derived from pressure-volume curves and chlorophyll a fluorescence (Fv/Fm) in juvenile and adult thalli sampled in three different dates between March and April 2023. F. virsoides exhibited remarkable water stress tolerance, as evidenced by the low water potential at turgor loss point (Ψtlp, -7.0 MPa on average), and the maintenance of high Fv/Fm at low water potentials indicating a prolonged maintenance of healthy physiological status. While no differences were observed between growth stages, Ψtlp, capacitance (C) and the bulk modulus of elasticity (ε) varied significantly according to the sampling dates, whereas the osmotic potential at full turgor did not significantly change. Ψ measured on thalli collected after a typical prolonged emersion period was markedly lower (-12.3 MPa on average) than the estimated Ψtlp, suggesting that the population is frequently undergoing turgor loss. Further investigations are required to determine environmental tolerance ranges based on water status characteristics to enhance our understanding of F. virsoides responses and vulnerability to climate change, thus providing insight into the possible causes of its widespread decline.

The CO2 electrolysing mechanism in single-phase mixed-conducting cathode of solid oxide cell.

In the field of solid oxide cells (SOC), unveiling the electrochemical reaction and transfer mechanisms in mixed ionic and electronic conducting (MIEC) electrodes is of great importance. Due to the chemical capacitance effects of MIEC materials, SOC often shows large capacitance current during electrochemical tests, which might interfere with the polarization behaviors. This work presents a numerical multiphysical model based on the transport of oxygen species, which accurately and concisely replicates the current-voltage curves of a solid oxide electrolysis cell (SOEC) with MIEC electrodes under various scanning rates. The scanning IV and electrochemical impedance spectra measurement under different SOEC working conditions are combined to enable the separation of Faradic and charging currents. Thus, both the bulk diffusion and surface gaseous diffusion of the oxygen species are encompassed, which explains how the current being generated due to intertwined chemical capacitance effects and chemical reactions in the MIEC electrodes.

The significance of upper glycolytic components in regulating retinal pigment epithelial cellular behavior.

Cell adhesion to the extracellular matrix and its natural outcome of cell spreading, along with the maintenance of barrier activity, are essential behaviors of epithelial cells, including retinal pigment epithelium (RPE). Disruptions in these characteristics can result in severe vision-threatening diseases such as diabetic macular edema and age-related macular degeneration. However, the precise mechanisms underlying how RPE cells regulate their barrier integrity and cell spreading are not fully understood. This study aims to elucidate the relative importance of upper glycolytic components in governing these cellular behaviors of RPE cells. Electric Cell-Substrate Impedance Sensing (ECIS) technology was utilized to assess in real-time the effects of targeting various upper glycolytic enzymes on RPE barrier function and cell spreading by measuring cell resistance and capacitance, respectively. Specific inhibitors used included WZB117 for Glut1 inhibition, Lonidamine for Hexokinase inhibition, PFK158 for PFKFB3/PFK axis inhibition, and TDZD-8 for Aldolase inhibition. Additionally, the viability of RPE cells was evaluated using a lactate dehydrogenase (LDH) cytotoxicity assay. The most significant decrease in electrical resistance and increase in capacitance of RPE cells were observed due to dose-dependent inhibition of Glut1 using WZB117, as well as Aldolase inhibition with TDZD-8. LDH level analysis at 24-72 h post-treatment with WZB117 (1 and 10 µM) or TDZD-8 (1 µM) showed no significant difference compared to the control, indicating that the disruption of RPE functionality was not attributed to cell death. Lastly, inhibition of other upper glycolytic components, including PFKFB3/PFK with PFK158 or Hexokinase with Lonidamine, did not significantly affect RPE cell behavior. This study provides insights into the varied roles of upper glycolytic components in regulating the functionality of RPE cells. Specifically, it highlights the critical roles of Glut1 and Aldolase in preserving barrier integrity and promoting RPE cell adhesion and spreading. Such understanding will guide the development of safe interventions to treat RPE cell dysfunction in various retinal disorders.

An afferent nerve-like electronic device with somatic mechanical perception and sensation management.

Tactile and pain perception are essential for biological skin to interact with the external environment. This complex interplay of sensations allows for the detection of potential threats and appropriate responses to stimuli. However, the challenge is to enable flexible electronics to respond to mechanical stimuli such as biological skin, and researchers have not clearly reported the successful integration of somatic mechanical perception and sensation management functions into neuro-like electronics. In this work, an afferent nerve-like device with a pressure sensor and a perception management module is proposed. The pressure sensor comprises two conductive fabric layers and an ionic hydrogel, forming a capacitor structure that emulates the swift transition from tactile to pain perception under mechanical stimulation. Drawing inspiration from the neuronal "gate control" mechanism, the sensation management module adjusts signals in response to rubbing, accelerating the discharge process and reducing the perception duration, thereby replicating the inhibitory effect of biological neurons on pain following tactile interference. This integrated device, encompassing somatic mechanical perception and sensation management, holds promise for applications in soft robotics, prosthetics, and human-machine interaction.

Copper Vanadium Oxide Yolk-Shell Microspheres with Excellent Capacitance and Cycling Performance for Electrochromic Supercapacitor.

Vanadium pentoxide (V2O5) is considered a promising material for electrochromic supercapacitors due to its rich color transitions and excellent electrochemical capacity. However, V2O5 exhibits low electrical conductivity, and its volume changes dramatically during charge-discharge cycles, leading to structural collapse and poor long-term cyclability. These issues have hindered the development and application of V2O5. In this study, copper vanadium oxide yolk-shell microspheres (CVO) were synthesized through a one-step solvent heat treatment with an annealing process. With the doping of copper element, the capacitance, conductivity, and cyclic stability of CVO microspheres were significantly enhanced. Subsequently, the sphere-wire network structure was formed by blending Na2V6O16·3H2O nanowires (NVO), resulting in the formation of CVO/NVO composites. The three-dimensional sphere-wire network efficiently facilitates the acquisition of additional redox sites and strengthens the material-to-substrate bonding. Under the combined influence of these favorable factors, CVO/NVO achieved a high specific capacitance of 39.2 mF cm-2, with a capacitance retention of 84% after 7500 cycles at a current density of 0.7 mA cm-2. The fully inorganic solid-state electrochromic supercapacitor (ECSC), assembled on the basis of CVO/NVO, demonstrates a vivid and clearly distinguishable color change (ΔE* = 37). Even more impressive is the energy storage capacity (18.4 mF·cm-2) and the cycling stability (up to 89% retention after 10,000 cycles) exhibited by the devices. These key performances are superior to those of most of the previously reported V2O5-based ECSCs, opening a promising avenue for the development of V2O5-based electrochromic energy storage devices.

The Evaluation of Interface Quality in HfO2 Films Probed by Time-Dependent Second-Harmonic Generation.

Time-dependent second-harmonic generation (TD-SHG) is an emerging sensitive and fast method to qualitatively evaluate the interface quality of the oxide/Si heterostructures, which is closely related to the interfacial electric field. Here, the TD-SHG is used to explore the interface quality of atomic layer deposited HfO2 films on Si substrates. The critical SHG parameters, such as the initial SHG signal and characteristic time constant, are compared with the fixed charge density (Qox) and the interface state density (Dit) extracted from the conventional electrical characterization method. It reveals that the initial SHG signal linearly decreases with the increase in Qox, while Dit is linearly correlated to the characteristic time constant. It verifies that the TD-SHG is a sensitive and fast method, as well as simple and noncontact, for evaluating the interface quality of oxide/Si heterostructures, which may facilitate the in-line semiconductor test.

Electrostatic Correlations Lead to High Capacitance in Zwitterion-Containing Thin Films.

A novel zwitterion composed of an imidazolium tethered to an anionic sulfonyl(trifluoromethane sulfonyl)imide group was prepared as an alternative dielectric material to traditional ionic liquids. The zwitterion not only melted below 100 °C but also proved to be nonhygroscopic. High-capacitance organic dielectric materials were obtained by blending this compound with poly(methyl methacrylate) over a range of concentrations and thicknesses. Above a specific temperature and concentration, films exhibit a capacitance nearly equivalent to that of an electrostatic double layer, approximately 10 µF/cm2, regardless of their thickness. Grazing-incidence wide-angle X-ray scattering experiments suggest that the zwitterions adopt a lamellar ordering at their surface above a critical concentration. The observed ordering is correlated with a 1000-fold increase in capacitance. The behavior suggests that the zwitterions exhibit strong electrostatic correlations throughout the film bulk, pointing the way toward a novel class of organic dielectric materials.

Pinpointing Moisture: The Capacitive Detection for Standing Tree Health.

BACKGROUND: the feasibility of the capacitance method for detecting the water content in standing tree trunks was investigated using capacitance-based equipment that was designed for measuring the water content of standing tree trunks. METHODS: In laboratory experiments, the best insertion depth of the probe for standing wood was determined by measurement experiments conducted at various depths. The bark was to be peeled when specimens and standing wood were being measured. The actual water content of the test object was obtained by specimens being weighed and the standing wood being weighed after the wood core was extracted. RESULTS: A forecast of the moisture content of standing wood within a range of 0 to 180% was achieved by the measuring instrument. The feasibility of the device for basswood and fir trees is preliminarily studied. When compared to the drying method, the average error of the test results was found to be less than 8%, with basswood at 7.75%, and fir at 7.35%. CONCLUSIONS: It was concluded that the measuring instrument has a wide measuring range and is suitable for measuring wood with low moisture content, as well as standing timber with high moisture content. The measuring instrument, being small in size, easy to carry, and capable of switching modes, is considered to have a good application prospect in the field of forest precision monitoring and quality improvement.

Thickness-dependent Relative Dielectric Constant of Organic Ultrathin Films.

In formulas employed for analysis of organic electronic devices, the relative dielectric constant value of the semiconductor organic films is often assumed rather than measured, even though it is a fundamental parameter for a correct interpretation. This is particularly true for ultrathin films made of discrete molecular layers. In this work, Spectroscopy Ellipsometry and Scanning Capacitance Microscopy were used to study thin films made of N,N'-bis(n-octyl)-x:y,dicyanoperylene-3,4:9,10-bis(dicarboximide). The relative dielectric constant presents a non-monotonic trend with thickness: it is equal to 2.1 for one molecular layer, saturating at 3.2 for increasing thickness. This maximum value, equivalent to the bulk one, occurs when the coverage is in between the third to the fourth layer. In this range, the growth switches from a Frank-Van der Merwe (2D growth) to a Volmer-Weber mode (3D growth); in addition, the molecular configuration assumes a bent/distorted geometry with respect to the initial edge-on one. These results establish a morphological dependence of the dielectric constant, especially in the vicinity of the substrate interface, that disappears at a certain distance from it.

Versatile Activated Carbon Fibers Derived from the Cotton Fibers Used as CO2 Solid-State Adsorbents and Electrode Materials.

Activated carbon has an excellent porous structure and is considered a promising adsorbent and electrode material. In this study, activated carbon fibers (ACFs) with abundant microporous structures, derived from natural cotton fibers, were successfully synthesized at a certain temperature in an Ar atmosphere and then activated with KOH. The obtained ACFs were characterized by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), elemental analysis, nitrogen and carbon dioxide adsorption-desorption analysis, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and N2 adsorption-desorption measurement. The obtained ACFs showed high porous qualities and had a surface area from 673 to 1597 m2/g and a pore volume from 0.33 to 0.79 cm3/g. The CO2 capture capacities of prepared ACFs were measured and the maximum capture capacity for CO2 up to 6.9 mmol/g or 4.6 mmol/g could be achieved at 0 °C or 25 °C and 1 standard atmospheric pressure (1 atm). Furthermore, the electrochemical capacitive properties of as-prepared ACFs in KOH aqueous electrolyte were also studied. It is important to note that the pore volume of the pores below 0.90 nm plays key roles to determine both the CO2 capture ability and the electrochemical capacitance. This study provides guidance for designing porous carbon materials with high CO2 capture capacity or excellent capacitance performance.