Effect of the scanner type on the marginal gap and internal fit of two monolithic CAD/CAM esthetic crown materials: An in vitro study.

BACKGROUND: The durability of indirect restorations is significantly influenced by marginal adaptation and internal fit. The use of computer-aided design/computer-aided manufacturing (CAD/CAM) with digital impressions has reduced dental prosthesis fabrication errors, improving the long-term survivability of the restorations. OBJECTIVES: The present study assessed the impact of intraoral and extraoral scanning methods on the marginal adaptation and internal fit of 2 different types of monolithic crowns manufactured using CAD/CAM. MATERIAL AND METHODS: A total of 40 three-dimensional (3D) resin-printed dies were randomly assigned to 2 groups based on the type of crown material (n = 20 per group). Each group was divided into 2 subgroups (n = 10 per group) according to the die-scanning technique: subgroup A, scanned using the intraoral scanner (IOS) Primescan; and subgroup B, scanned using the extraoral scanner (EOS) inEos X5. The digitized photos were converted into a 3D virtual crown design using CAD software. The internal discrepancy values, and the marginal gap between the 3D resin-printed die and the crown were assessed using a ×50 digital microscope. The data was checked for normality with the Kolmogorov-Smirnov test, and the Mann-Whitney U test was used to compare the tested groups. The collected data was analyzed at a significance level set at p < 0.05. RESULTS: The different scanning techniques used had a statistically significant effect on the vertical marginal gap and the internal fit [µm] (p < 0.05). As far as the crown materials are concerned, BRILLIANT Crios showed a significantly higher marginal gap as compared to Tetric CAD when scanned with inEos X5 (p = 0.004), whereas the differences were insignificant with regard to the internal fit (p > 0.05).The crown parameters tested with both scanning systems were within the clinically acceptable ranges. CONCLUSIONS: Scanning methods and crown materials had an impact on the internal fit and vertical marginal gap of monolithic crowns.

A Modified Technique for Simplifying Full-Arch Screw-Retained Implant Rehabilitation With Rapid Digital Conversion: A Case Report.

In this case report, a new modified technique is described for an efficient, simple, and effective digital approach to immediate provisionalization of the implant-supported full-arch prosthesis. Today's patient population is increasingly educated about treatment options and expects efficient, esthetic, and comfortable results. This novel technique delivers on these aims while eliminating the many challenges posed by previously described digital and analog techniques to the immediate provisionalization of the implant-supported full-arch prosthesis. This technique requires minimal chair time and cost to the provider and reduces patient discomfort and complication risk. This technique therefore presents a promising new protocol for this popular procedure.

Fluorescence intensity of composite resin for direct veneer removal using a fluorescence-aided identification technique.

OBJECTIVES: This laboratory study evaluated the influence of the fluorescence intensity of composite resins on additional tooth wear and the presence of restorative material in different dental thirds during the retreatment of direct veneers. MATERIALS AND METHODS: The crown dimensions of 60 bovine incisors were reduced to 10 × 8 mm. The teeth were classified according to the fluorescence intensity of the composites: low (LOW) (TPH Spectra), medium (MED) (Opallis), and high (HIGH) (Essentia) groups. The teeth were divided according to the removal methods: conventional (CON) and fluorescence-aided identification technique (FIT). The specimens were scanned (T0), received veneer preparation, and scanned again (T1). After restorations, the composites were removed and the teeth were scanned (T2). Measurement assessments between T1 and T2 were performed to determine additional wear, presence of residual areas, and the average between additional wear and the presence of residual areas. Kruskal Wallis, Mann-Whitney, Friedman, 2-way ANOVA, and post-Tukey tests were performed (α < 0.05). RESULTS: The comparison of composite resins indicated a smaller area of additional wear and greater residue presence in the HIGH group than the LOW group for both techniques in the cervical third. Regarding removal methods, the FIT produced greater additional wear than the CON method for the LOW and MED groups in the middle and cervical thirds. The incisal third exhibited greater additional wear than the other thirds. CONCLUSIONS: Composite resins with high fluorescence intensity removed using FIT had less tooth wear. The incisal third was the most affected area for direct veneer removal procedures. CLINICAL SIGNIFICANCE: A FIT has been proposed for composite resin removal; however, the different fluorescence intensities of composite resins can influence tooth wear caused during this procedure.

Does intra-oral scan improve the impression accuracy of full-arch implant-supported prostheses: A systematic review and meta-analysis.

OBJECTIVES: The present study aimed to systematically review the studies comparing the accuracy of intraoral scan (IOS) and conventional implant impressions (CI) in completely edentulous patients. MATERIALS AND METHODS: Electronic searches were performed in PubMed, Embase and Cochrane CENTRAL up to December 1, 2023. Clinical studies and in vitro studies reporting the accuracy of digital full arch impressions were included. The primary outcome is the 3-dimensional deviations between the study reference models. A risk of bias assessment was performed for clinical studies. A stratified meta-analysis and a single-armed meta-analysis were conducted. RESULTS: A total of 49 studies were included, with 8 clinical studies and 41 in vitro studies. For comparison between IOS and conventional impressions, studies were categorized into two groups based on the different measurement methods employed: RMS and CMM. In studies using RMS, the result favored the IOS in the unparalleled situation with the mean difference of -99.29 µm (95% CI: [-141.38, -57.19], I2 = 81%), while the result was opposite with the mean difference of 13.62 µm (95% CI: [10.97, 16.28], I2 = 26%) when implants were paralleled. For different brands of IOS, the accuracy ranged from 76.11 µm (95% CI: [42.36, 109.86]) to 158.63 µm (95% CI: [-14.68, 331.93]). CONCLUSIONS: Accuracy of intraoral scan is clinically acceptable in edentulous arches, especially for unparalleled implants. More clinical studies are needed to verify the present finding.

Accuracy of conventional impressions and digital scans for implant-supported fixed prostheses in maxillary free-ended partial edentulism: An in vitro study.

OBJECTIVES: To evaluate the accuracy of conventional polyether impressions and digital scans produced by five intra-oral scanners (IOSs) in maxillary free-ended partial edentulism for long-span implant-supported prostheses. METHODS: This in vitro study involved the impression of a maxillary model with free-end partial edentulism, in which six implants were placed before digitization using a desktop scanner to generate a digital reference model. Conventional impressions (Impregum Penta Soft, 3M) and digital scans with five IOSs (Trios 3 and 4, 3Shape; Primescan, Dentsply-Sirona; CS 3600, Carestream Dental; and i-500, Medit) were obtained. Conventional impressions were digitized using the same desktop scanner. Each digital STL file of conventional or digital impressions was superimposed over the reference STL file to enable comparison. Trueness was assessed by calculating angles and distance deviations. For precision, dispersions of values around their means were also measured. RESULTS: The mean distance deviation was significantly higher for conventional impressions (454.24 ± 334.70 µm) than for IOSs (ranging from 160.98 ± 204.48 µm to 255.56 ± 395.89 µm) (p < 0.001). The mean angular deviation was high with conventional impressions (1.82 ± 1.51°), intermediate with CS 3600 (1.38 ± 1.42°), Primescan (1.37 ± 2.54°) and Trios 4 (1.30 ± 0.64°) scanners, and lower with I500 (0.97 ± 0.75°) and Trios 3 (1.01 ± 0.85°) scanners (p < 0.001). The dispersion of distance values around their means was lowest with Trios 3 and i-500, followed by CS3600, Primescan, and Trios 4, respectively, and higher for conventional impressions (p < 0.001). The dispersion of angular values was smallest with i-500, Trios 3, and Trios 4 compared with other groups and was highest with Primescan (p < 0.001). CONCLUSIONS: Within the limits of the current study, Trios 3 scanner exhibited the highest accuracy, followed by i-500, Trios 4, CS 3600, Primescan, and conventional impressions respectively. IOSs might be reliable for the fabrication of an implant-supported prosthesis. In vivo studies are required to confirm these findings. CLINICAL SIGNIFICANCE: Passive adaptation of the implant-supported framework is a challenge when rehabilitating patients with maxillary free-end partial edentulism. While Conventional impressions remain a reliable and validated technique, but IOSs demonstrated higher accuracy, suitable for the fabrication of long-span implant-supported prostheses in partially edentulous arch.

Effect of artificial landmarks of the prefabricated auxiliary devices located at different arch positions on the accuracy of complete-arch edentulous digital implant scanning: An in-vitro study.

OBJECTIVES: To examine the effect of artificial landmarks of prefabricated auxiliary devices (PAD) located at different arch positions on the accuracy of complete-arch edentulous digital implant scanning. METHODS: A reference model containing four analogs and PAD were fabricated by a 3D printer (AccuFab-C1s, 3DShining). 10 digital scans were performed using an intraoral scanner (Aoralscan 3, 3DShining), sv 1.0.0.3115, with artificial landmarks located at different arch positions: group I, without any artificial landmarks; group II, with artificial landmarks at the anterior region; group III, with artificial landmarks at the posterior region. group IV: with artificial landmarks at both anterior and posterior regions. For group V: Conventional open-tray splinted impressions. The reference file and conventional stone casts were digitalized by using a dental laboratory scanner. The related files were imported into inspection software for trueness and precision assessment. Statistical analysis was performed with One-way ANOVA and Kruskal-Wallis test. The level of significance was set at α=0.05. RESULTS: For the global accuracy assessment, significantly higher global trueness was seen in group II (p < 0.01), III (p < 0.001), IV (p < 0.001) and V (p < 0.001) than group I. Significantly higher global precision was seen in group III (p < 0.001), IV (p < 0.001) and V (p < 0.001) than group I. For the local accuracy assessment, the PAD primarily improved accuracy on the linear deviations. CONCLUSIONS: Artificial landmarks of PAD at different arch positions significantly influenced the scanning accuracy. Applying the PAD in group IV could achieve comparable outcomes to conventional open-tray splinted impressions. Artificial landmarks on the posterior region may be more pivotal than those on the anterior region. CLINICAL SIGNIFICANCE: Group IV could achieve comparable accuracy to conventional open-tray splinted impressions.

Comparative analysis of the trueness of linear measurements using direct and indirect scanning protocols compared to actual clinical measurements.

OBJECTIVES: To assess the trueness of digital measurements using direct and indirect scanning approaches compared to the actual clinical measurements. MATERIALS AND METHODS: The crown length, width, and width/length ratio were measured in 36 anterior maxillary teeth using three different methods. The first was clinically using a digital caliper, the second was by scanning the teeth using a digital scanner and the third was by making an impression of the teeth, constructing a stone cast in the lab, and scanning it to obtain digital measurements. Bland-Altman test and intraclass correlation were used to assess the data and make comparisons. RESULTS: Measurements taken using both approaches were highly reliable, with intraclass correlations ranging from 0.934 to 0.977 (p ≤ 0.000). Bland-Altman plot reflected a minimal mean difference between measurements especially in crown width measurements. Crown width/crown length measurement displayed the highest mean difference. CONCLUSIONS: Both direct and indirect optical surface scans showed similar high trueness in linear measurements of teeth. A higher discrepancy was detected in the crown width/length ratio. CLINICAL SIGNIFICANCE: Digital dentistry is the new era in patient management. The use of conventional impression techniques and physical dental casts is associated with several disadvantages. Scanning dental casts to convert physical records into digital ones has multiple advantages. Optical surface scans (digital models) of the dentition are currently being more broadly used and advocated in the different dental disciplines including the construction of surgical guides for esthetic crown lengthening procedures. The trueness and reliability of linear measurements are of paramount importance to allow for proper fit and predictable outcomes. In this study, the trueness of these linear measurements obtained using direct and indirect methods was compared to the actual clinical measurements.

Patient-reported outcomes and framework fit accuracy of removable partial dentures fabricated using digital techniques: A systematic review and meta-analysis.

PURPOSE: This review aimed to summarize the evidence on patient-reported outcomes and clinical performance of digitally fabricated removable partial dentures (RPDs) compared to traditionally fabricated dentures. METHODS: Three databases were systematically searched (PubMed, CENTRAL, and Wiley online library) for clinical studies comparing digitally and conventionally fabricated RPDs regardless of data acquisition methods used for fabrication. The Cochrane Collaboration risk of bias assessment tool 2 and the Oxford Center for Evidence-based Medicine tool were used to assess risk of bias, and level of evidence, respectively. Descriptive narrative analysis was used to summarize data on patient-reported outcomes, as there were inadequate studies to pool data in a meta-analysis. A random-effects model was used to analyze the data of framework fit accuracy. RESULTS: Ten randomized controlled trials were included in the systematic review, and 4 were included in the meta-analysis. Two studies showed that digitally fabricated RPDs are associated with higher patient satisfaction than conventionally fabricated RPDs (with a mean difference of 12.5 mm on a 100-satisfaction scale, p = .008). The pooled standardized mean difference for framework fit accuracy was 0.49 (p = 0.02) in favor of conventionally fabricated RPDs, which showed that conventionally fabricated RPDs have a quantitatively better fit compared to digitally fabricated RPDs. However, clinical evaluation studies showed that both frameworks have clinically acceptable fit. CONCLUSIONS: Current evidence shows that digitally fabricated RPDs are associated with higher patient satisfaction compared to conventionally fabricated RPDs. However, the scarcity of literature here warrants the generalization of this conclusion. Both digitally and conventionally fabricated metal RPD frameworks showed acceptable fit clinically.

Bone Volume Assessment Around Immediate Dental Implant in the Esthetic Area with Immediate Tooth-Like Single Crown Provisionalization: A Laser and Computed Tomography 1-Year Retrospective Study.

PURPOSE: To examine the remodeling process of both the soft and hard tissue components of the postextraction socket around immediately loaded dental implants after tooth extraction in maxillary esthetic areas. MATERIALS AND METHODS: Subjects underwent immediate placement of single implants in postextraction sockets without bone grafting, and their immediate provisionalization with custom tooth-like interim crowns were fabricated using digital diagnostic impressions and a dental milling machine. Intraoperative and 1-year follow-up layered scans of the postextraction sockets after implantation were acquired using a 3D optical system. In the short term, subjects underwent computed tomographic scans. Digital impressions for gingival contours, originally stored as STL (standard tessellation language) files, were converted to DICOM (Digital Imaging and Communications in Medicine) files with the implant shoulder working as a referral point, which were then superimposed to 3D radiologic images. The observed volumetric and linear outcomes were measured using a program known as DentaScan. The width of the alveolar crest at the level of the implant shoulder and marginal bone levels were acquired. Nonparametric tests were applied with a level of significance set at P < .01. RESULTS: No failure was reported after a follow-up of 1 year. Little or no inflammation of the treated areas was registered, and there were practically no signs of suppuration. The areas showed a significant reduction in the overall volumes for both soft and bone tissue, with a P value < .0001 from the baseline (0.983 ± 0.172 cm3) to the 1-year survey (0.865 ± 0.156 cm3). If the soft and bone tissue changes were separately evaluated, a significant loss (with a P value < .0001) was registered for only the bone tissues (from 0.434 ± 0.075 to 0.355 ± 0.061 cm3). Moreover, changes in gingival tissue from baseline to the 1-year survey (-0.040 ± 0.067) appeared to be significantly different from the overall volume loss (-0.118 ± 0.083 cm3). A shrinkage in width (-0.5 ± 0.7 mm) was found from baseline (12.6 ± 0.6 mm) to the 1-year follow-up (12.1 ± 0.9 mm). Marginal bone levels were 0.97 ± 0.70 mm and 0.39 ± 0.78 mm, respectively, at the mesial and distal aspects of the implants. CONCLUSIONS: The present analysis suggested that immediately customized provisionalization was effective enough to prevent both volume loss and linear shrinkage at the layers of the treated areas. Moreover, the buccal aspects seemed to be the areas most affected by the loss of volume. The mean loss in width, which amounted to roughly 0.5 mm, appeared to be negligible when compared to the overall width measured before surgery.

Noncarious cervical lesions in the aging population analyzed through digital scanning: occlusal risk factors, dimensions, and morphology.

OBJECTIVES: To evaluate noncarious cervical lesions (NCCL) in older adults by analyzing each lesion's morphology, dimension, and occlusal risk factors using intraoral scanning and clinical evaluation. MATERIALS AND METHODS: Individuals over 60 treated at the School of Dentistry in Minas Gerais, Brazil, were invited to participate in this cross-sectional study. We clinically evaluated 1245 teeth for the presence of NCCL and dentin hypersensitivity (DH) in 53 individuals. Three-dimensional models were obtained using Omnicam, and occlusal risk factors were evaluated through the presence of wear facets, intense occlusal contacts, and interferences. The 3Shape 3DViewer software was used to classify NCCL morphology and to measure their height. NCCL depth, width, and area measurements were determined using ImageJ. Descriptive analyses were performed. The Kolmogorov-Smirnov test showed that quantitative data exhibited non-normal distribution. For bivariate analyses of quantitative data, the Mann-Whitney test was employed. The results were reported with mean, standard deviation, median, minimum, and maximum. For bivariate analyses of categorical data, the Pearson chi-square test was used. The results were reported with frequencies (counts) and percentages. A regression model evaluating the association between occlusal risk factors and the absence/presence of NCCL was built. RESULTS: Most participants were female (58.5%), with a mean age of 66. The frequency of NCCL was 28.27%, corresponding to 352 teeth. Of these, 68.18% exhibited saucer morphology and 31.82% wedge-shaped morphology. The frequency of DH was 13.92% in teeth with NCCL. Saucer NCCL exhibited significantly greater height (p = 0.02), while wedge-shaped lesions showed greater depth (p < 0.001). Also, teeth with NCCL had a higher proportion of wear facets (66.8%; p < 0.001), intense occlusal contacts (39.8%; p = 0.008), and occlusal interferences (21.9%; p = 0.05). The regression model showed that teeth with wear facets were 1.50 times more likely to exhibit NCCL than teeth without wear facets (p < 0.001). Teeth with intense occlusal contact were 1.22 times more likely to exhibit NCCL than teeth without intense occlusal contact (p = 0.031). CONCLUSIONS: NCCL is a common dental condition in the older adults evaluated in this study. Wedge-shaped NCCL exhibited greater depth, while saucer NCCL had more expressive height. Occlusal risk factors may represent a crucial mechanism for the occurrence of NCCL in this population. CLINICAL RELEVANCE: Understanding the mechanisms involved in developing NCCL is helpful in diagnostic and preventive practices. The study showed the importance of dental occlusion and characteristics of different NCCL morphologies that help the clinician in decision-making.

Fluorescence-aided identification technique using a low-cost violet flashlight and rotatory instruments for dental trauma splint removal.

BACKGROUND/AIM: Removing resin composites used for bonding dental trauma splints may result in irreversible damage to the enamel. This in vitro study evaluated the influence of additional violet illumination and different bur types on damage caused to tooth enamel. MATERIALS AND METHODS: Fifteen maxillary models with four bovine incisor teeth were prepared. All models were scanned using a laboratory scanning system (s600 ARTI; Zirkonzahn). Six experimental groups (n = 10) were generated by two study factors: lighting type (three levels), (1) low-cost (5-7 US$) violet LED flashlight (LUATEK, LT 408); (2) VALO Cordless light curing unit (Ultradent) with black lens; or (3) without additional illumination; and rotatory instrument (two levels), (1) diamond bur or (2) multifluted tungsten-carbide bur. New scanning was performed after splint removal, and the generated files were superimposed on the initial scans using Cumulus software. The light emitted by both violet light sources was characterized by using integrating sphere and beam profile. A qualitative and quantitative analysis of enamel damage and two-way ANOVA followed by Tukey's post hoc was used at an α = 0.05. RESULTS: The use of low-cost violet flashlight that emitted the violet peak light at 385 nm and VALO Cordless with black lens at 396 nm resulted in significantly lower damage to the enamel surface than those in the groups without additional violet light (p < .001). An interaction between rotatory instruments and lighting was found. When no additional violet lighting was used, the diamond bur presented higher mean and maximum depth values. CONCLUSIONS: Fluorescence lighting facilitated the removal of remnant resin composite dental trauma splints, leading to less invasive treatment. The diamond bur resulted in higher enamel damage than that affected by the multifluted bur when no violet lighting was used. A low-cost violet flashlight is a useful fluorescence-aided identification technique for removing resin composite dental trauma splints.

Accuracy of Conventional and Digital Impressions for Full-Arch Implant-Supported Prostheses: An In Vitro Study.

Both conventional and digital impressions aim to record the spatial position of implants in the dental arches. However, there is still a lack of data to justify the use of intraoral scanning over conventional impressions for full-arch implant-supported prostheses. The objective of the in vitro study was to compare the trueness and precision of conventional and digital impressions obtained with four intra-oral scanners: Trios 4 from 3Shape®, Primescan from Dentsply Sirona®, CS3600 from Carestream® and i500 from Medit®. This study focused on the impression of an edentulous maxilla in which five implants were placed for implant-supported complete prosthesis. The digital models were superimposed on a digital reference model using dimensional control and metrology software. Angular and distance deviations from the digital reference model were calculated to assess trueness. Dispersion of the values around their mean for each impression was also calculated for precision. The mean distance deviation in absolute value and the direction of the distance deviation were smaller for conventional impressions (p-value < 0.001). The I-500 had the best results regarding angular measurements, followed by Trios 4 and CS3600 (p < 0.001). The conventional and I-500 digital impressions showed the lowest dispersion of values around the mean (p-value < 0.001). Within the limitations of our study, our results revealed that the conventional impression was more accurate than the digital impression, but further clinical studies are needed to confirm these findings.

Volume assessment of the external contour around immediate implant with or without immediate tooth-like crown provisionalization: A digital intraoral scans study.

PURPOSES: To examine differences between immediate and delayed dental implant loading in maxillary aesthetic areas. METHODS: In this retrospective controlled analysis, 43 subjects who underwent immediate placement of the dental implant in a post-extraction socket were ranked into either immediate (24 implants loaded with non-occlusal tooth-like profile provisional prostheses fabricated by virtual diagnostic impressions and an in-office dental milling machine) or delayed group (19 implants loaded with conventional cover screws and secondary intention healing). Intraoperatively and then four months later, scans of the external layers were acquired with an optical scanner. The width of the alveolar crest and Jemt papilla index were acquired. Non-parametric tests were applied with a level of significance set at p < 0.01. RESULTS: In both groups, the volumes and areas showed significant reductions from the baseline to the 4-month survey. Reductions in volume appeared to be statistically different between the two groups (-39±31 mm3 for the immediate and 89 ± 30 mm3 for the delayed group). The final Jemt papilla index appeared significantly different between the immediate (mesial, 2.5 and, distal, 3) and delayed groups (2 for both aspects). CONCLUSIONS: Immediate provisionalization significantly reduced volume loss and area shrinkage at the external layer when data were compared to a delayed rehabilitation strategy.

Comparison of the Effectiveness of the Ultrasonic Method and Cone-Beam Computed Tomography Combined with Intraoral Scanning and Prosthetic-Driven Implant Planning Method in Determining the Gingival Phenotype in the Healthy Periodontium.

The aim of this study was to compare the effectiveness of two diagnostic methods: ultrasonic gingival thickness measurement (UGTM) and cone-beam computed tomography, intraoral scanning by computer-aided design technology with prosthetic-driven implant planning software (CBCT/CAD/PDIP) in determining the gingival phenotype (GP). Thirty periodontally healthy patients were examined. The ultrasonic device Pirop G® with a frequency of 20 MHz and CBCT/CAD/PDIP were used to measure gingival thickness at upper canines and incisors in three points localized midbuccally, namely free gingival thickness (FGT), supracrestal (SGT) and crestal (CGT). Probing depth (PD), clinical attachment level (CAL) and width of keratinized tissue (WKT) were measured using periodontal probe. Intra-examiner and inter-examiner agreement and agreement between methods were evaluated using Bland-Altman analyses. Comparing both methods in the determination of SGT (bias = 0.17 mm, SD = 0.25 mm, p < 0.000) and CGT (bias = -0.45 mm, SD = 0.32 mm, p < 0.000) 95.0% and 95.6% agreement were found, respectively, and in the FGT range only 93.3% (bias = -0.45 mm, SD = 0.32 mm, p < 0.000). The presence of positive correlations between WKT and SGT was shown. A positive correlation between SGT and WKT confirms the purpose of measuring these parameters for the evaluation of the GP. Both the ultrasonic method and cone-beam computed tomography combined with intraoral scanning and prosthetic-driven implant planning method were useful in determining gingival phenotype, however, the ultrasonic method was more accurate for measuring GT.

A Retrospective Digital Analysis of Contour Changing after Tooth Extraction with or without Using Less Traumatic Surgical Procedures.

BACKGROUND: The present retrospective analysis aimed to compare two different single tooth extraction surgical approaches in both premolar and molar areas: less traumatic magneto-electrical versus conventional tooth extraction in minimizing the edentulous ridge volume loss. METHODS: In the present retrospective control trial, 48 patients who underwent one-tooth extraction, were allocated either to control (28 sites treated with conventional tooth extraction procedures) or test group (20 subjects treated with less traumatic tooth extraction procedures by tooth sectioning and magnetoelectric roots subluxation). Intraoperatively (during tooth extraction surgery just after the subsequent filling of the alveolar socket with the sterile fast re-absorbable gelatin sponge), and then four months later, contours of the sockets were acquired through a laser intra-oral scanner. The digitally superimposed models were converted to dicom (Digital Imaging and Communications in Medicine) format first, then volumetric and area evaluations were performed with a DentaScan tool package. Non-parametric tests were applied with a level of significance set at p < 0.01. RESULTS: significant reductions of anatomical features were observed four months later in all the groups (p-values < 0.001) with volume losses leading to a final alveolar ridge volume of 0.87 ± 0.34 cm3 for atraumatic extractions and 0.66 ± 0.19 cm3 for conventional extractions. No significant differences were registered for outcomes related to the basal surface variables. When just molar tooth were considered, the outcomes relating to volume loss between baseline and four months (ΔV) and its percentage (ΔV%) showed a better behavior in the less traumatic procedure (ΔV = -0.30 ± 0.10 cm3 and ΔV% = -22.3 ± 8.4%) compared to the conventional extractions (ΔV = -0.59 ± 0.10 cm3 and ΔV% = -44.3 ± 5.8%) with p-values < 0.0001. CONCLUSIONS: at four months, the less traumatic tooth extraction procedures by tooth sectioning and magnetoelectric root subluxation seemed to be able to better preserve the volume of the alveolar crest (reduction close to 22% with less traumatic extraction in molar sites) when compared to subjects treated with the conventional tooth extraction techniques.

Experimental data on water vapour adsorption on silica gel in fully packed and Z-annulus packed beds.

Experimental data on water vapour adsorption on silica gel in four packed bed configurations namely fully packed bed (FPB), large annulus packed bed (LAPB), medium annulus packed bed (MAPB) and small annulus packed bed (SAPB) are presented. Raw temperature data from designated mass transfer zones (MTZ) in the packed beds and on their corresponding walls are presented along with data of the inlet and outlet moist air conditions. Pressure transducers installed at the inlet and outlet provided pressure data. The presented data also covers the material properties of the silica gel for adsorption obtained through material testing and analysis in the laboratory. With detailed experimental methodology and comprehensive material and water vapour adsorption data, this article can help other researchers to validate and verify the performance of their adsorption systems. The material property data presented can also help investigators to use appropriate experimentally determined property values of silica gel in their theoretical studies. Furthermore, this data can serve as a basis of comparison for heat and mass transfer in other experimental adsorption systems.

An overview on the veracity of intraoral digital scanning system and utilization of iTero scanner for analyzing orthodontic study models both In-Vivo and Ex-Vivo.

In the domain of orthodontics, plaster models are contemplated as one of the important tools for diagnosis and treatment planning. In Dentistry, technological advancement has developed in the section of diagnostic devices, for example, the utilization of a 3D intraoral scanner, which can convert plaster models into digital models. With in-office utilization of this system, orthodontists can more meticulously and precisely construct custom braces, clear aligners, and orthodontic appliances. The digital data can be stored as a stereolithography file; it eliminates the disadvantages encountered with the storage of plaster models like breakage, space required, and distortion of the plaster models. ITero®element is the intraoral laser scanner (ILS) which utilizes parallel confocal scanning technology which maximizes the accuracy of the scan. By utilizing the iTero scanner, the dental measurement can be performed in OrthoCADTM software which is highly accurate. The objective of the contemporary study is to review the literature of studies on in-vivo and ex-vivo scanning with the iTero system.

A Digital Technique to Replicate Edentulous Arches with Functional Borders and Accurate Maxillomandibular Relationship for Digital Complete Denture.

Correct functional border impression and jaw registration is a challenge when edentulous arches are directly digitized with an intraoral scanner. This article describes a digital workflow to replicate complete edentulous arches with full functional contour, and position them in the centric relation using an intraoral scanner, existing denture, and three-dimensional image reversal technique. Based on the reconstructed images, the base and dental parts of the new denture can be designed efficiently and predictably.

Effect of personalized miniscrew-assisted rapid palatal expander on expansion of the median palatal suture in adults / 口腔疾病防治

Objective@# To investigate the manufacturing procedures of personalized miniscrew-assisted rapid palatal expanders (pMARPE) using digital technologies and to evaluate the effect of the expanders when expanding the midpalatal suture of an adult. @*Methods@# Digital technologies were used to make pMARPE, which was used to treat a 21-year-old woman with maxillary transverse deficiency (MTD). The relevant literature on MARPE was reviewed.@* Results@#PMARPE could be manufactured using intraoral digital scanning, computer-aided design and computer-aided manufacturing(CAD/CAM ), and 3D printing technologies. After expansion, the width of the anterior midpalatal suture, posterior midpalatal suture and maxillary skeletal width increased by 3.9 mm, 3.2 mm and 4.7 mm, respectively. There was no significant change in the inclination of maxillary first molars, and the height of alveolar ridge decreased slightly. It could be seen that using digital technologies to manufacture personalized expanders was possible for MARPE , and the initial stability of miniscrews played an important role in the expansion success rate, the increase of molar inclination is composed of many parts, and the decrease of alveolar ridge height may be overestimated due to the measurement method, as shown by a literature review. @*Conclusion@#The midpalatal suture of an adult patient with MTD could be expanded by pMARPE. However, the effect of this expander on the inclination of the first molar and alveolar bone height needs to be further studied with a larger sample size.

Characterization of an anti-foaming and fast-setting gypsum for dental stone.

OBJECTIVE: An anti-foaming and fast-setting gypsum for dental stone recently became available on the market. Interestingly, this product can be mixed by the cocktail shaking method, providing a more convenient way to obtain high reproducibility when fabricating error-free study models for digital dentistry. The aim of this study is to investigate setting time, surface bubble formation, and other gypsum characteristics of three dental stone products with different mixing methods. METHODS: Shake mix stone (SM), new plastone 2 white (NP), and Hi-Koseton (HK) were chosen. Using different mixing methods (cocktail shaking, hand mixing, hand mixing+vibrating, and hand mixing+vacuum process), the characteristics of dental stone were investigated according to ISO 6873. Powder size, morphology, and thermo/chemical analyses were performed. RESULTS: Regardless of the method of mixing, SM exhibited the fastest setting time (3-4min) and the smallest number (˜10% versus HK) and area (˜30% versus HK) of surface bubbles among the investigated products, while setting expansion, mechanical properties such as compressive/impact strength and microhardness and detail reproduction before and after digital scanning were similar. A smaller size (˜1.5µm) and unidentified additives were revealed as possible reasons for the above anti-foaming and fast-setting characteristics. SIGNIFICANCE: Anti-foaming and fast-setting characteristics of a developed gypsum for dental stone were confirmed even with shaking.