Impact of functional dietary fiber incorporation on the appearance and mechanical properties of extruded high moisture meat analogs.

The effect of including functional dietary fiber ingredients (FDFI) on the texture and structure of high moisture meat analog (HMMA) was examined in this study. The inclusion of FDFI in this application is hypothesized to act as a label-friendly texture modifier in HMMA while also boosting the product's dietary fiber content. Two inclusion rates (5% and 10% wt/wt) of four functionally unique FDFI ingredients (pea hull, citrus fiber, hydrocolloid oat bran, and powdered cellulose) were blended with wheat protein isolate. Each unique formulation was processed using a high-moisture twin-screw extrusion process at two different screw speeds (200 and 400 rpm). The type of FDFI added affected the mechanical texture attributes (hardness, springiness, cohesiveness, and integrity index) and in-process behavior (torque and pressure) of the resulting HMMA far more than the inclusion rate or screw speed (p > 0.05). The type of FDFI ingredient employed also had the largest qualitative effect on the visual appearance of the resulting HMMA. These observed quality changes correlated well with the physicochemical and structure-function properties of the FDFI ingredients, especially with water-holding and absorption capacities. The incorporation of FDFI is a viable means of modulating HMMA texture and improving the holistic nutrition of these products. PRACTICAL APPLICATION: Adding highly functional, dietary fiber-rich ingredients to processed foods is a viable strategy for improving the nutritional and textural quality of these foods. The results of this study imply that these fibers can be added to meat analogs at nutritionally relevant rates, and the texture of the resulting product can be tailored based on the functional properties of the ingredients deployed.

Spatial-temporal comparison of Eph/Ephrin gene expression in ocular lenses from aging and knockout mice.

Cataracts, defined as any opacity in the transparent ocular lens, remain the leading cause of blindness and visual impairment in the world; however, the etiology of this pathology is not fully understood. Studies in mice and humans have found that the EphA2 receptor and the ephrin-A5 ligand play important roles in maintaining lens homeostasis and transparency. However, due to the diversity of the family of Eph receptors and ephrin ligands and their promiscuous binding, identifying functional interacting partners remains a challenge. Previously, 12 of the 14 Ephs and 8 of 8 ephrins in mice were characterized to be expressed in the mouse lens. To further narrow down possible genes of interest in life-long lens homeostasis, we collected and separated the lens epithelium from the fiber cell mass and isolated RNA from each compartment in samples from young adult and middle-aged mice that were either wild-type, EphA2-/- (knockout), or ephrin-A5 -/- . Reverse transcription quantitative polymerase chain reaction (RT-qPCR) was implemented to compare transcript levels of 33 Eph and ephrin gene variants in each tissue compartment. Our results show that, of the Eph and ephrin variants screened, 5 of 33 showed age-related changes, and 2 of 33 showed genotype-related changes in lens epithelium. In the isolated fibers, more dynamic gene expression changes were observed, in which 12 of 33 variants showed age-related changes, and 6 of 33 showed genotype-related changes. These data allow for a more informed decision in determining mechanistic leads in Eph-ephrin-mediated signaling in the lens.

A phase 2a study investigating the effects of ritlecitinib on brainstem auditory evoked potentials and intraepidermal nerve fiber histology in adults with alopecia areata.

Reversible axonal swelling and brainstem auditory evoked potential (BAEP) changes were observed in standard chronic (9-month) toxicology studies in dogs treated with ritlecitinib, an oral Janus kinase 3/tyrosine kinase expressed in hepatocellular carcinoma family kinase inhibitor, at exposures higher than the approved 50-mg human dose. To evaluate the clinical relevance of the dog toxicity finding, this phase 2a, double-blind study assessed BAEP changes and intraepidermal nerve fiber (IENF) histology in adults with alopecia areata treated with ritlecitinib. Patients were randomized to receive oral ritlecitinib 50 mg once daily (QD) with a 4-week loading dose of 200 mg QD or placebo for 9 months (placebo-controlled phase); they then entered the active-therapy extension and received ritlecitinib 50 mg QD (with a 4-week loading dose of 200 mg in patients switching from placebo). Among the 71 patients, no notable mean differences in change from baseline (CFB) in Waves I-V interwave latency (primary outcome) or Wave V amplitude on BAEP at a stimulus intensity of 80 dB nHL were observed in the ritlecitinib or placebo group at Month 9, with no notable differences in interwave latency or Wave V amplitude between groups. The CFB in mean or median IENF density and in percentage of IENFs with axonal swellings was minimal and similar between groups at Month 9. Ritlecitinib treatment was also not associated with an imbalanced incidence of neurological and audiological adverse events. These results provide evidence that the BAEP and axonal swelling finding in dogs are not clinically relevant in humans.

Fine structural analysis of degummed fibroin fibers reveals its superior mechanical capabilities.

Silk fibers constitute a class of protein building blocks capable of functionalization and reprocessing into various material formats. The properties of these fibers are typically affected by the intense thermal treatments needed to remove the sericin gum coating layer. Additionally, their mechanical characteristics are often misinterpreted by assuming the cross-sectional area is a perfect circle. The thermal treatments impact not only the mechanics of the fibers but also the structure of the resolubilized protein, thereby limiting the performance of the resulting silk-based materials. To mitigate these limitations, we explored varying alkali conditions at low temperatures for surface treatment, effectively removing the sericin gum layer while preserving the molecular structure of the fibroin protein, thus, maintaining the hierarchical integrity of the exposed fibroin microfiber core. The precise determination of the initial CSA of the asymmetrical silk fibers led to a comprehensive analysis of their mechanical properties. Our findings indicate that the alkali surface treatment raised the Young's modulus and tensile strength by increasing the fibers' crystallinity by approximately 40% and 50%, respectively, without compromising their strain. We have shown that this treatment facilitated further production of high-purity soluble silk with rheological and self-assembly characteristics comparable to those of native silk.

Correlation of functional magnetic resonance imaging features of primary central nervous system lymphoma with vasculogenic mimicry and reticular fibers.

Objective: To deepen the imaging-pathological mechanism of primary central nervous system lymphoma (PCNSL) and provide a theoretical basis for clinical diagnosis and treatment, the functional magnetic resonance imaging (fMRI) characteristics of PCNSL were analyzed, and the relationship between the fMRI characteristics and vasculogenic mimicry (VM) and reticular fiber in PCNSL was discussed. Methods: Ninety-six patients with PCNSL treated in our hospital were divided into three groups according to the pathological examination results, including strong positive group of VM (n = 40), weak positive group of VM (n = 56), strong positive group of reticular fiber (n = 45) and weak positive group of reticular fiber (n = 51). The levels of augmentation index and apparent diffusion coefficient (ADC) were compared among the groups. receiver operator characteristic (ROC) curve analysis was used to analyze the clinical value of ADC value in differential diagnosis of PCNSL. Results: The levels of augmentation index in the strong positive group of VM were significantly higher than that in the weak positive group of VM, and the ADC value in the strong positive group of VM was significantly lower than that in the weak positive group of VM (P < 0.001). The levels of augmentation index in the strong positive group of reticular fiber were significantly higher than that in the weak positive group of reticular fiber, and ADC value in the strong positive group of reticular fiber was significantly lower than that in reticular fiber weak positive group (P < 0.001). Pearson correlation analysis showed that the levels of augmentation index were positively correlated with VM and reticular fiber (r = 0.529, 0.548, P < 0.001) and the ADC value was negatively correlated with VM and reticular fiber (r = -0.485, -0.513, P < 0.001). There was a significant negative correlation between necrotic lesions and VM (r = -0.185, P < 0.05). The area under the curve (AUC) values of average ADC value, minimum ADC value, and maximum ADC value for individual differential diagnosis of PCNSL were 0.920, 0.901, and 0.702, while the AUC of the combined differential diagnosis was 0.985, with a sensitivity of 95.00 % and a specificity of 92.70 %. Conclusion: The levels of augmentation index and the ADC value of PCNSL focus are significantly correlated with VM and reticular fiber, and there is a strong negative correlation between necrotic lesions and VM. MRI imaging technology is of great significance in revealing the biological behavior of PCNSL, which can effectively reveal the relationship between VM and reticular fibers and the MRI characteristics in PCNSL, thereby providing a new imaging basis for the clinical diagnosis and treatment of PCNSL.

Enhanced flexibility of high-yield bamboo pulp fibers via cellulase immobilization within guar gum/polyacrylamide/polydopamine interpenetrating network hydrogels.

Softness is a crucial criterion in assessing the comfort and usability of tissue paper. Flexible fibers contribute to the softness of the tissue paper by allowing the sheets to conform to the contours of the skin without feeling rough or abrasive. This study focuses on developing innovative CGG/APAM/PDA hydrogels with interpenetrating networks consisting of cationic guar gum, anionic polyacrylamide, and polydopamine for cellulase immobilization, aimed at improving bamboo fiber flexibility. Cellulase biomolecules are efficiently immobilized on CGG/APAM/PDA hydrogels through the Schiff base reaction. Immobilized cellulases have a wider pH applicability than free cellulases, good storage stability, and can maintain high relative activity at relatively high temperatures. The treatment of bamboo fibers with immobilized cellulase results in a significant increase in flexibility, reaching 6.90 × 1014 N·m2, which is 7.18 times higher than that of untreated fibers. The immobilization of cellulases using CGG/APAM/PDA hydrogels as carriers results in a substantial enhancement of storage stability, pH applicability, and inter-fiber bonding strength, as well as the capacity to sustain high relative enzymatic activity at elevated temperatures. The immobilization of cellulase within CGG/APAM/PDA interpenetrating network hydrogels presents a viable strategy for enhancing bamboo fiber flexibility, thereby expanding the accessibility of tissue products.

Life cycle assessment of chemically treated and copper coated sustainable biocomposites.

The current demand for composites reinforced with renewable fibers is greater than it has ever been. In comparison to glass fibers, natural fibers yield the advantages of lesser density and cost. Although comparable specific properties exist between glass and natural fibers, the latter shows lower strength. However, with the copper coating and chemical treatment of natural fibers, the strength of the composites can be increased nowadays. The current research investigation focuses on the life cycle assessment of the raw, chemically treated, and copper coated fiber reinforced bagasse and banana composites to compare the emissions on the environment of these samples to prove their applicability. The study includes all the processes, from the extraction of fibers to the formation of composites, i.e., from cradle to gate, and detailed inventory. The ReCiPe H midpoint method has been utilized in SimaPro software to quantify the emissions. The results indicate that the maximum global warming emission is due to the energy consumption used during the manufacturing of these composites. Electricity contribution for chemically treated and copper coated composites in global warming contribution is slightly greater than that of raw composites i.e., 73.275 % in C- BG/P, 73.06 % in Cu- BG/P, 73.65 % in C- BN/P and 74.28 % in Cu- BN/P which is comparatively higher than 63.8 % in R- BG/P and 64.97 % in R- BN/P. The next major contributions come from polylactic acid for all the three samples of bagasse fiber reinforced PLA composite and banana fiber reinforced PLA composite. The raw samples also show improved fiber strength compared to chemical and copper coated samples.

Stress distribution pattern in two different no-post systems in endodontically treated maxillary central incisors: A three-dimensional finite element analysis.

Aim: This study aimed to evaluate the stress distribution in an endodontically treated tooth restored with two different reinforcing fibers followed by direct composite restoration using a finite element analysis (FEA). Settings and Design: FEA. Subjects and Methods: Two three-dimensional models of endodontically treated maxillary central incisors were restored with two reinforcing fibers: the polyethylene fibers (PFs) and the short fiber-reinforced composite (SFRC), respectively. The restoration was carried out without any intraradicular preparation using direct composite restoration. The models were generated using SolidWorks. The elastic modulus and Poisson's ratio for various structures and materials were installed into the simulation software, Abaqus. A FEA was then conducted. Each model received a mixed-mode loading of 150 N as distributed pressure to the specified region, and stress distribution was evaluated using the von Mises criteria. Results: Both the reinforcing materials, PF and SRFC, showed maximum concentration of stresses in the cervical third of the tooth. The calculated values of the von Mises stresses for the PF and the SFRC models were 1.7 Mpa and 1.9 Mpa, respectively. Moreover, the stresses generated were of low intensity and were uniformly distributed, suggesting that by using this technique, stresses may be very well tolerated by the remaining tooth structure without any fracture. Conclusion: This no-posttechnique, using the two reinforcing fibers, showed minimal stress concentration in the cervical region of the tooth. Thus, using this ultraconservative approach that aims to preserve and reinforce the pericervical dentin and restore the remaining tooth structure with direct composite restoration could be a promising treatment option for the rehabilitation of badly mutilated teeth.

Constructing Stiff ß-Sheet for Self-Reinforced Alginate Fibers.

The application of alginate fibers is limited by relatively low mechanical properties. Herein, a self-reinforcing strategy inspired by nature is proposed to fabricate alginate fibers with minimal changes in the wet-spinning process. By adapting a coagulation bath composing of CaCl2 and ethanol, the secondary structure of sodium alginate (SA) was regulated during the fibrous formation. Ethanol mainly increased the content of ß-sheet in SA. Rheological analysis revealed a reinforcing mechanism of stiff ß-sheet for enhanced modulus and strength. In combination with Ca2+ crosslinking, the self-reinforced alginate fibers exhibited an increment of 39.0% in tensile strength and 71.9% in toughness. This work provides fundamental understanding for ß-sheet structures in polysaccharides and a subsequent self-reinforcing mechanism. It is significant for synthesizing strong and tough materials. The self-reinforcing strategy involved no extra additives and preserved the degradability of the alginate. The reinforced alginate fibers exhibited promising potentials for biological applications.

Fire Properties of Paper Sheets Made of Cellulose Fibers Treated with Various Retardants.

This article presents the results of flame-retardancy tests conducted on cellulose sheets produced using a Rapid Köthen apparatus treated with retardants. The agents used were potassium carbonate (PC) K2CO3 (concentrations of 20; 33.3; and 50% wt/wt), monoammonium phosphate (MAP) NH4H2PO4 (concentrations of 35% wt/wt), diammonium phosphate (DAP) (NH4)2HPO4 (concentrations of 42.9% wt/wt), and bisguanidal phosphate (FOS) C2H10N6 (concentrations of 22.5% wt/wt). The agents were used to improve Kraft cellulose-based sheets' flame-retardant properties and compare their performances. As part of the study, the flammability of the materials was determined by the following methods: an oxygen index (OI) test, a mass loss calorimeter (MLC) test, and a mini fire tube (MFT) test. All formulations showed an increase in flame retardancy compared to the control test. All protected samples were non-flammable for OI determinations, and DAP-protected samples showed the highest OI index. For the MLC test, DAP-protected and MAP-protected samples showed the best heat-release rate (HRR), total heat release (THR), and average heat-release rate (ARHE) (samples did not ignite for 600 s). In the MFT test, all treated samples had comparably reduced weight loss. The best parameter was achieved for MAP and DAP (15% weight loss).

Experimental Study on the Flexural Performance of Steel-Polyvinyl Alcohol Hybrid Fiber-Reinforced Concrete.

This paper explores the impact of steel-PVA hybrid fibers (S-PVA HF) on the flexural performance of panel concrete via three-point bending tests. Crack development in the concrete is analyzed through Digital Image Correlation (DIC) and Scanning Electron Microscope (SEM) experiments, unveiling the underlying mechanisms. The evolution of cracks in concrete is quantitatively analyzed based on fractal theory, and a predictive model for flexural strength (PMFS) is established. The results show that the S-PVA HF exhibits a synergistic effect in enhancing and toughening the concrete at multi-scale. The crack area of steel-PVA hybrid fiber concrete (S-PVA HFRC) is linearly correlated with deflection (δ), and it further reduces the crack development rate and crack area compared to steel fiber-reinforced concrete (SFRC). The S-PVA HF improves the proportional ultimate strength (fL) and residual flexural strength (fR,j) of concrete, and the optimal flexural performance of concrete is achieved when the steel fiber dosage is 1.0% and the PVA fiber dosage is 0.2%. The established PMFS of hybrid fiber-reinforced concrete (HFRC) can effectively predict the flexural strength of concrete.

Effect of Basalt/Steel Individual and Hybrid Fiber on Mechanical Properties and Microstructure of UHPC.

Ultra High-Performance Concrete (UHPC) is a cement-based composite material with great strength and durability. Fibers can effectively increase the ductility, strength, and fracture energy of UHPC. This work describes the impacts of individual or hybrid doping of basalt fiber (BF) and steel fiber (SF) on the mechanical properties and microstructure of UHPC. We found that under individual doping, the effect of BF on fluidity was stronger than that of SF. Moreover, the compressive, flexural, and splitting tensile strength of UHPC first increased and then decreased with increasing BF dosage. The optimal dosage of BF was 1%. At a low content of fiber, UHPC reinforced by BF demonstrated greater flexural strength than that reinforced by SF. SF significantly improved the toughness of UHPC. However, a high SF dosage did not increase the strength of UHPC and reduced the splitting tensile strength. Secondly, under hybrid doping, BF was partially substituted for SF to improve the mechanical properties of hybrid fiber UHPC. Consequently, when the BF replacement rate increased, the compressive strength of UHPC gradually decreased; on the other hand, there was an initial increase in the fracture energy, splitting tensile strength, and flexural strength. The ideal mixture was 0.5% BF + 1.5% SF. The fluidity of UHPC with 1.5% BF + 0.5% SF became the lowest with a constant total volume of 2%. The microstructure of hydration products in the hybrid fiber UHPC became denser, whereas the interface of the fiber matrix improved.

Ion channel profiles of extraocular motoneurons and internuclear neurons in human abducens and trochlear nuclei.

Introduction: Extraocular muscles are innervated by two anatomically and histochemically distinct motoneuron populations: motoneurons of multiply-innervated fibers (MIF), and of singly-innervated fibers (SIF). Recently, it has been established by our research group that these motoneuron types of monkey abducens and trochlear nuclei express distinct ion channel profiles: SIF motoneurons, as well as abducens internuclear neurons (INT), express strong Kv1.1 and Kv3.1b immunoreactivity, indicating their fast-firing capacity, whereas MIF motoneurons do not. Moreover, low voltage activated cation channels, such as Cav3.1 and HCN1 showed differences between MIF and SIF motoneurons, indicating distinct post-inhibitory rebound characteristics. However, the ion channel profiles of MIF and SIF motoneurons have not been established in human brainstem tissue. Methods: Therefore, we used immunohistochemical methods with antibodies against Kv, Cav3 and HCN channels to (1) examine the human trochlear nucleus in terms of anatomical organization of MIF and SIF motoneurons, (2) examine immunolabeling patterns of ion channel proteins in the distinct motoneurons populations in the trochlear and abducens nuclei. Results: In the examination of the trochlear nucleus, a third motoneuron subgroup was consistently encountered with weak perineuronal nets (PN). The neurons of this subgroup had -on average- larger diameters than MIF motoneurons, and smaller diameters than SIF motoneurons, and PN expression strength correlated with neuronal size. Immunolabeling of various ion channels revealed that, in general, human MIF and SIF motoneurons did not differ consistently, as opposed to the findings in monkey trochlear and abducens nuclei. Kv1.1, Kv3.1b and HCN channels were found on both MIF and SIF motoneurons and the immunolabeling density varied for multiple ion channels. On the other hand, significant differences between SIF motoneurons and INTs were found in terms of HCN1 immunoreactivity. Discussion: These results indicated that motoneurons may be more variable in human in terms of histochemical and biophysiological characteristics, than previously thought. This study therefore establishes grounds for any histochemical examination of motor nuclei controlling extraocular muscles in eye movement related pathologies in the human brainstem.

Cellulose nanocrystals-based optical organohydrogel fiber with customizable iridescent colors for strain and humidity response.

Stimuli-responsive optical hydrogels are widely used in various fields including environmental sensing, optical encryption, and intelligent display manufacturing. However, these hydrogels are susceptible to water losses when exposed to air, leading to structural damage, significantly shortened service lives, and compromised durability. This study presents mechanically robust, environmentally stable, and multi-stimuli responsive optical organohydrogel fibers with customizable iridescent colors. These fibers are fabricated by incorporating tunicate cellulose nanocrystals, alginate, and acrylamide in a glycerol-water binary system. The synthesized fibers exhibit high strength (1.38 MPa), moisture retention capabilities, and elastic properties. Furthermore, a sensor based on these fibers demonstrates high- and low-temperature resistance along with stimuli-responsive characteristics, effectively detecting changes in environmental humidity and strains. Moreover, the fiber sensor demonstrates continuous, repeatable, and quantitatively predictable moisture discoloration responses across a humidity range of 11 % and 98 %. During strain sensing, the optical-organohydrogel-based sensor demonstrates a large working strain (50 %) and excellent cycling stability, underscoring its potential for effectively monitoring a wide range of intricate human motions. Overall, the synthesized fibers and their simple fabrication method can elicit new avenues for numerous related applications including the large-scale implementation of advanced wearable technology.

Exposure to fibres and risk of pleural mesothelioma in the Norwegian Offshore Petroleum Workers cohort.

OBJECTIVES: Pleural mesothelioma is a rare respiratory cancer, mainly caused by inhalation of asbestos fibres. Other inorganic fibres are also suggested risk factors. We aimed to investigate the association between exposure to asbestos or refractory ceramic fibres (RCFs) and pleural mesothelioma among male Norwegian offshore petroleum workers. METHODS: Among 25 347 men in the Norwegian Offshore Petroleum Workers (NOPW) cohort (1965-1998), 43 pleural mesothelioma cases were identified through the Cancer Registry of Norway (1999-2022). A case-cohort study was conducted with 2095 randomly drawn non-cases from the cohort. Asbestos and RCF exposures were assessed with expert-made job-exposure matrices (JEMs). Weighted Cox regression was used to estimate HRs and 95% CIs, adjusted for age at baseline and pre-offshore employment with likely asbestos exposure. RESULTS: An increased risk of pleural mesothelioma was indicated for the highest versus lowest tertile of average intensity of asbestos (HR=1.21, 95% CI: 0.57 to 2.54). Pre-offshore asbestos exposure (vs no such exposure) was associated with increased risk of pleural mesothelioma (HR=2.06, 95% CI: 1.11 to 3.81). For offshore workers with no pre-offshore asbestos exposure, an increased risk of pleural mesothelioma was found for the highest tertile of average intensity of asbestos (HR=4.13, 95% CI: 0.93 to 18), versus the lowest tertile. No associations were found between RCF and pleural mesothelioma. CONCLUSIONS: Associations between JEM-based offshore asbestos exposure and pleural mesothelioma were confirmed in the NOPW cohort. Pleural mesothelioma risk was also associated with asbestos exposure before work in the offshore petroleum industry.

Bridging sustainability and industry through resourceful utilization of pea pods- A focus on diverse industrial applications.

The focus on sustainable utilization of agricultural waste is currently a leading area of scientific research, driving significant advancements in technology and circular economy models. The fundamental capacity of bio-based products, bioprocessing techniques, and the crucial involvement of microbial treatments are opening opportunities for efficient solutions in various industries. One of the most popular green vegetables, peas are members of the Fabaceae family and have a pod-like structure. Every year, a significant amount of pea pods is discarded as waste products of peas that have negative impacts on our environment. In this comprehensive review, we explore innovative methods for utilizing pea pods to minimize their environmental footprint and optimize their viability across multiple industries. A large portion of the pea processing industry's output consists of pea pods. Variety of proteins, with major classes being globulin and albumin (13%), dietary fiber (43-58%), and minerals are abundant in these pods. Because of their diverse physiochemical properties, they find applications in many diverse fields. The porous pea pods comprised cellulose (61.35%) and lignin (22.12%), which could make them superior adsorbents. The components of these byproducts possess valuable attributes that make them applicable across treatment of wastewater, production of biofuels, synthesis of biocolors, development of nutraceuticals, functional foods, and enzymes for the textile industry, modification of oil, and inhibition of steel corrosion.

The potential use of birds as bioindicators of suspended atmospheric microplastics and artificial fibers.

Microplastics (MPs) and artificial fibers (AFs) have been detected suspended tens of meters above ground level in the atmosphere, yet empirical data on them remain scarce. This study aimed to investigate the presence of MPs and AFs in the digestive and respiratory systems of two abundant bird species, the Common House Martin (Delichon urbicum) and the Common Swift (Apus apus), within the Community of Madrid, Spain. Given that these birds spend the majority of their lives airborne, engaging in activities such as mating and sleeping during flight, the research sought to assess the potential of using these bird species as bioindicators for suspended atmospheric MPs and AFs. Samples were obtained from necropsies of birds (N = 24) collected primarily between spring and summer from 2021 to 2023. Only individuals that died within the initial 24-hour period and had not been fed were selected for examination to avoid contamination. MPs and AFS were identified by micro-FTIR, characterized and quantified. Results revealed that 75 % of the sampled birds exhibited at least one MPs in their respiratory and/or digestive system. All identified MPs were fibers, with polyester (PES) being the most predominant (48 %), followed by acrylic fibers (ACR; 28 %), and polyethylene (PE; 18 %). The average concentrations in the respiratory system were 1.12 ± 0.45 MPs/specimen and 2.78 ± 1.04 AFs/specimen for Common Swift and 0.75 ± 0.30 MPs/specimen and 0.75 ± 0.36 AFs/specimen for House Martin. In the digestive system, these were 1.92 ± 0.72 MPs/specimen and 3.42 ± 0.69 AFs/specimen for Common Swift, and 1.34 ± 0.50 MPs/specimen and 1.39 ± 0.47 AFs/specimen for House Martin. Birds collected areas with high population density located in the direction of the prevailing winds showed a concentration of MPs significantly higher in the digestive system. Taken together, these findings confirmed the potential use of these birds as bioindicators for monitoring of suspended atmospheric MPs and AFs.

Comparative analysis of the chimpanzee and human brain superficial structural connectivities.

Diffusion MRI tractography (dMRI) has fundamentally transformed our ability to investigate white matter pathways in the human brain. While long-range connections have extensively been studied, superficial white matter bundles (SWMBs) have remained a relatively underexplored aspect of brain connectivity. This study undertakes a comprehensive examination of SWMB connectivity in both the human and chimpanzee brains, employing a novel combination of empirical and geometric methodologies to classify SWMB morphology in an objective manner. Leveraging two anatomical atlases, the Ginkgo Chauvel chimpanzee atlas and the Ginkgo Chauvel human atlas, comprising respectively 844 and 1375 superficial bundles, this research focuses on sparse representations of the morphology of SWMBs to explore the little-understood superficial connectivity of the chimpanzee brain and facilitate a deeper understanding of the variability in shape of these bundles. While similar, already well-known in human U-shape fibers were observed in both species, other shapes with more complex geometry such as 6 and J shapes were encountered. The localisation of the different bundle morphologies, putatively reflecting the brain gyrification process, was different between humans and chimpanzees using an isomap-based shape analysis approach. Ultimately, the analysis aims to uncover both commonalities and disparities in SWMBs between chimpanzees and humans, shedding light on the evolution and organization of these crucial neural structures.

Plakophilin 4 controls the spatio-temporal activity of RhoA at adherens junctions to promote cortical actin ring formation and tissue tension.

Plakophilin 4 (PKP4) is a component of cell-cell junctions that regulates intercellular adhesion and Rho-signaling during cytokinesis with an unknown function during epidermal differentiation. Here we show that keratinocytes lacking PKP4 fail to develop a cortical actin ring, preventing adherens junction maturation and generation of tissue tension. Instead, PKP4-depleted cells display increased stress fibers. PKP4-dependent RhoA localization at AJs was required to activate a RhoA-ROCK2-MLCK-MLC2 axis and organize actin into a cortical ring. AJ-associated PKP4 provided a scaffold for the Rho activator ARHGEF2 and the RhoA effectors MLCK and MLC2, facilitating the spatio-temporal activation of RhoA signaling at cell junctions to allow cortical ring formation and actomyosin contraction. In contrast, association of PKP4 with the Rho suppressor ARHGAP23 reduced ARHGAP23 binding to RhoA which prevented RhoA activation in the cytoplasm and stress fiber formation. These data identify PKP4 as an AJ component that transduces mechanical signals into cytoskeletal organization.