Enhanced forward osmosis desalination of brackish water using phase-separating ternary organic draw solutions of hydroxypropyl cellulose and propylene glycol propyl ether.

This study introduces draw solutions for application in forward osmosis (FO) processes, combining mono propylene glycol propyl ether (PGPE) with the cellulose derivative hydroxypropyl cellulose (HPC). A total of 16 unique single-solute and ternary organic draw solutions were prepared and evaluated, leading to the selection of three promising solutions for further investigation. Notably, eight of the initial organic draw solutions demonstrated osmotic pressures exceeding 2.4 MPa. The dynamic viscosities of all draw solutions exhibited a significant reduction with increasing temperature. Among the investigated solutions, the 0.25HPC-3.75PGPE demonstrated the most favorable FO performance, achieving average experimental water fluxes of 11.062 and 9.852 Lm-2 h-1 (LMH) against a 1 g/L NaCl brackish feed solution across two FO runs. PRACTITIONER POINTS: Hydroxypropyl cellulose (HPC, MW ~100,000) was mixed with propylene glycol propyl ether (PGPE) as draw solutes for FO processes. Seven combinations of HPC and PGPE produced osmolalities greater than 1000 mOsm/kg. 0.5HPC-7.5PGPE ternary draw solution achieved experimental water fluxes of 11.062 and 9.852 LMH against 1 g/L NaCl brackish feed solution. Leveraging the LCSTs of these ternary organic solutions holds promise for improved separation and regeneration processes.

H2O2 oxidation - CaO precipitation pretreatment combining forward osmosis for electroless nickel spent tank liquid (ENSTL) reduction.

The electroless nickel spent tank liquid (ENSTL), as a typical hazardous waste, contains a variety of refractory organic substances as well as heavy metals and inorganic salts. Generally, ENSTL is delegated for disposing by qualified hazardous waste disposal departments in China. However, the temporary storage, transportation, and higher entrusted disposal expenses increase the burden on enterprises producing the hazardous ENSTL. This paper explored an oxidation/precipitation pretreatment and forward osmosis (FO) combined process for ENSTL reduction. 400 mmol/L Hydrogen peroxide and 5.0 wt% calcium oxide were selected as the optimal pretreatment in order to minimize the osmotic pressure of ENSTL, by which the conductivity was significantly reduced from 50.8 mS/cm to 26.8 mS/cm. As a result, the concentrating factor (N) could be dramatically increased from 2.45 by the direct FO to 8.71 by the combined system. Accordingly, the average water flux during the 24 h concentrating cycle increased from 2.47 L/(m2·h) to 4.56 L/(m2·h). TOC rejection rate decreased from 90.23% to 84.39% due to the transformation of organic matter forms by the chemical oxidation during the pretreatment. Meanwhile, TP, Ni and NH4+ rejection rates decreased to a certain extent, which may related to the mitigation of membrane fouling by the pretreatment.

Viability of Total Ammoniacal Nitrogen Recovery Using a Polymeric Thin-Film Composite Forward Osmosis Membrane: Determination of Ammonia Permeability Coefficient.

Total ammoniacal nitrogen (TAN) occurs in various wastewaters and its recovery is vital for environmental reasons. Forward osmosis (FO), an energy-efficient technology, extracts water from a feed solution (FS) and into a draw solution (DS). Asymmetric FO membranes consist of an active layer and a support layer, leading to internal concentration polarization (ICP). In this study, we assessed TAN recovery using a polymeric thin-film composite FO membrane by determining the permeability coefficients of NH4+ and NH3. Calculations employed the solution-diffusion model, Nernst-Planck equation, and film theory, applying the acid-base equilibrium for bulk concentration corrections. Initially, model parameters were estimated using sodium salt solutions as the DS and deionized water as the FS. The NH4+ permeability coefficient was 0.45 µm/s for NH4Cl and 0.013 µm/s for (NH4)2SO4 at pH < 7. Meanwhile, the NH3 permeability coefficient was 6.18 µm/s at pH > 9 for both ammonium salts. Polymeric FO membranes can simultaneously recover ammonia and water, achieving 15% and 35% recovery at pH 11.5, respectively.

U(VI) mitigation via forward osmosis: Elucidation of retention mechanisms and co-ion effects.

Uranium (U) is a chemical and radioactive toxic contaminant affecting many groundwater systems. The focus of this study was to evaluate the suitability of forward osmosis (FO) for uranium rejection from contaminated groundwater under field-relevant conditions. Laboratory experiments with aqueous solution containing uranium were performed with FO membrane to understand the uranium rejection mechanism under varied pH, draw solution concentration, and presence of co-ions. Further, experiments were performed with U-contaminated field groundwater. Results of the hydrogeochemcial modelling using PHREEQC indicated that the rejection mechanism of uranium was highly dependent on aqueous speciation. Uranium rejection was maximum at alkaline pH with ca. 99% rejection due to charge-based interactions between membrane and dominant uranyl complexes. The results of the co-ion study indicated that nitrate and phosphate ions decrease uranium rejection. Whereas, bicarbonates, calcium, and magnesium ions concentrated uranium in feed solution. Further, the uranium adsorption onto the membrane surface primarily depended on pH of the aqueous solution with maximum adsorption at pH 5.5. Our results show that the World Health Organization's drinking water guideline value of 30 µgL-1 for U could be achieved via FO process in field groundwater containing low dissolved solids.

Synthesis of sodium alginate / polyvinyl alcohol / polyethylene glycol semi-interpenetrating hydrogel as a draw agent for forward osmosis desalination.

Typically, hydrogels are described as three-dimensional networks of hydrophilic polymers that are able to capture a certain mass of water within their structure. Recently, hydrogels have been widely used as drawing agents in forward osmosis (FO) desalination processes. The major aim of this study is to prepare a novel semi-interpenetrating hydrogel by crosslinking sodium alginate (SA) and polyvinyl alcohol (PVA) by using the epichlorohydrin (ECH) crosslinker and polyethylene glycol (PEG) interpenetrated within the hydrogel's network as a linear polymer. Based on the optimum composition of SA/PVA composite hydrogel obtained from our earlier research, the effect of various percentages of PEG on the response of the hydrogel was investigated. The optimal composition of SA/PVA/PEG hydrogel was characterized by scanning electron microscopy (SEM), compression strength testing, Fourier transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD). The morphological and mechanical properties of the SA/PVA/PEG semi-interpenetrating hydrogel were also compared to those of the SA/PVA composite hydrogel. Moreover, the performance of the optimal SA/PVA/PEG hydrogel in a FO batch unit as a drawing agent was investigated based on the optimal operation conditions from our previous experiments. The results showed that the optimal PEG/polymer blend mass ratio was 0.25, which increased the swelling ratio (SR) (%) of the hydrogel from 645.42 (of the neat SA/PVA hydrogel) to 2683. The SA/PVA/PEG semi-interpenetrating hydrogel was superior to the SA/PVA copolymer hydrogel in pore structure and mechanical properties. Additionally, in terms of FO desalination, the achieved water flux by SA/PVA/PEG hydrogel is higher than that accomplished by SA/PVA hydrogel.

Alcohol-alcohol-based draw solute minimizes the reverse solute flux in forward osmosis desalination.

Recently, alcohol-based draw solute (DS), i.e., alcohol with water, is one of the trending research topics in forward osmosis (FO) because of its performance and ease of regeneration. Nevertheless, the higher reverse solute flux (RSF) of the alcohol-based DS hinders its commercialization in water and wastewater treatment applications. This research aims to minimize the RSF of the alcohol-based DS in FO by investigating the possibility of using alcohol-alcohol-based draw solutes for the first time. Three alcohol-alcohol-based draw solutions, namely, (1) E70 + IPA30 (ethanol: 70% + isopropanol: 30%), (2) E40 + IPA60 (ethanol: 40% + isopropanol: 60%), and (3) E10 + IPA90 (ethanol: 10% + isopropanol: 90%), were prepared and the properties (including osmolality, shear stress, and viscosity) of the DS were first investigated followed by the parametric investigation (concerning temperature and concentration). The results were further analyzed with the fixed-point iterative method in MATLAB to obtain the performance parameters. Results reveal that the E10 + IPA90 mixture yields a lower RSF of 40.62 g/m2/h and specific reverse solute flux of 3.78 g/L with a considerably good water flux and recovery percentage of 11.47 LMH and 26.29%, respectively, as compared to other DS E70 + IPA30 and E40 + IPA60 at 25 °C. Thus, E10 + IPA90 is recommended as a potential candidate to be used as a DS in FO.

Innovative stimuli-responsive membrane MSF brine rejection dilution by tertiary treated sewage effluent.

In this study, treated wastewater and Multi-Stage Flash (MSF) brine were integrated into the Forward Osmosis (FO) system using pressure stimuli-responsive Nanofiltration (PSRNF) membranes to dilute magnesium, calcium, and sulfate MSF plant brine reject. The deposition of magnesium sulfate and calcium sulfate in the heat exchanger is one of the main issues affecting the performance and efficiency of MSF thermal desalination plants. Reducing the concentration of the divalent ions can minimize scale formation and deposition to a level that allows the MSF plant to operate at high top brine temperature (TBT) and without scale problems. The PSRNF membranes were chosen in the FO process because of their high water permeability, rejection of divalent and monovalent ions, small structure parameter (S), and inexpensiveness compared to commercial FO membranes. Three PSRNF membranes were tested in the FO process with the feed solution facing the active membrane layer to avoid active layer delamination. Although the PSRNF membrane exhibited negligible water flux at 0 bar, it increased when a 2-4 bar was applied to the feed solution. The wastewater temperature was set at 25 °C while 40 °C was the brine operational temperature to mimic the field situation. A maximum average water flux of 39.5 L/m2h was recorded at 4 bar feed pressure when the PSRNF membrane was used for the brine dilution, achieving up to 42% divalent ions dilution at 0.02 kWh/m3 specific power consumption. The average water flux in the PRSNF membrane was 35% higher than that in the commercial TFC FO membrane. Notably, the PSRNF membrane is ten times cheaper than commercial FO membranes. Notably, the PSRNF membrane is ten times cheaper than commercial FO membranes, achieving substantial cost reductions and pioneering advancements in FO purification technology.

Recycling scale inhibitor wastes into pH-responsive complexes to treat wastewater produced from spent lithium-ion battery disposal.

A large amount of organophosphorus-containing wastewater is produced in spent lithium-ion battery disposal. Forward osmosis (FO) offers unique advantages in purifying this kind of wastewater if suitable draw solutes - the core of FO technology, are available. Herein we synthesize several pH-sensitive zinc complexes, namely ZnATMP-iNa (i = 0, 1, 2, 3, 4), from ZnSO4 and amino tris(methylene phosphonic acid) (ATMP) obtained from scale inhibitor wastes for organophosphorus-containing wastewater remediation. Among these ZnATMP-iNa, ZnATMP-3Na best meets the standards of an ideal draw solute. This makes ZnATMP-3Na outperform other reported draw solutes. 0.6 M ZnATMP-3Na produces a water flux of 12.7 LMH, 136 % higher than that of NaCl and a solute loss of 0.015 g/L, lower than that of NH4HCO3 (0.83 g/L). In organophosphorus-containing wastewater treatment, ZnATMP-3Na has higher water recovery efficiency (8.3 LMH) and sustainability than NaCl and NH4HCO3, and is sufficient to handle large quantities of wastewater. Remarkably, the pH-responsive property allows ZnATMP-3Na to be readily recovered through pH-control and reused in FO. The ionic property, expanded cage-like structure and easy-recycling make ZnATMP-3Na achieve sustainable FO separation and superior to other draw solutes. This study provides inspiration for draw solute design from wastes and extends FO application to organophosphorus-containing wastewater remediation.

Unlocking groundwater desalination potential for agriculture with fertilizer drawn forward osmosis: prediction and performance optimization via RSM and ANN.

The agricultural sector uses 70% of the world's freshwater. As clean water is extracted, groundwater quality decreases, making it difficult to grow crops. Brackish water desalination is a promising solution for agricultural areas, but the cost is a barrier to adoption. This study investigated the performance of the fertilizer drawn forward osmosis (FDFO) process for brackish water desalination using response surface methodology (RSM) and artificial neural network (ANN) approaches. The RSM model was used to identify the optimal operating conditions, and the ANN model was used to predict the water flux (Jw) and reverse solute flux (Js). Both models achieved high accuracy, with RSM excelling in predicting Js (R2 = 0.9614) and ANN performing better for Jw (R2 = 0.9801). Draw solution (DS) concentration emerged as the most critical factor for both models, having a relative importance of 100% for two outputs. The optimal operating conditions identified by RSM were a DS concentration of 22 mol L-1, and identical feed solution (FS) and DS velocities of 8.1 cm s-1. This configuration yielded a high Jw of 4.386 LMH and a low Js of 0.392 gMH. Furthermore, the study evaluated the applicability of FDFO for real brackish groundwater. The results confirm FDFO's potential as a viable technology for water recovery in agriculture. The standalone FO system proves to be less energy-intensive than other desalination technologies. However, FO exhibits a low recovery rate, which may necessitate further dilution for fertigation purposes.

Critical review on salt tolerance improvement and salt accumulation inhibition strategies of osmotic membrane bioreactors.

The osmotic membrane bioreactor (OMBR) is a novel wastewater treatment and resource recovery technology combining forward osmosis (FO) and membrane bioreactor. It has attracted attention for its low energy consumption and high contaminant removal performance. However, in the long-term operation, OMBR faces the problem of salt accumulation due to high salt rejection and reverse salt flux, which affects microbial activity and contaminants removal efficiency. This review analyzed the feasibility of screening salt-tolerant microorganisms and determining salinity thresholds to improve the salt tolerance of OMBR. Combined with recent research, the inhibition strategies for salt accumulation were reviewed, including the draw solution, FO membrane, operating conditions and coupling with other systems. It is hoped to provide a theoretical basis and practical guidance for the further development of OMBR. Finally, future research directions were prospected. This review provides new insights for achieving stable operation of OMBR and promotes its wide application.

Concentration properties of biopolymers via dead-end forward osmosis.

Extracellular polymeric substances (EPSs) in excess sludge of wastewater treatment plants are valuable biopolymers that can act as recovery materials. However, effectively concentrating EPSs consumes a significant amount of energy. This study employed novel energy-saving pressure-free dead-end forward osmosis (DEFO) technology to concentrate various biopolymers, including EPSs and model biopolymers [sodium alginate (SA), bovine serum albumin (BSA), and a mixture of both (denoted as BSA-SA)]. The feasibility of the DEFO technology was proven and the largest concentration ratios for these biopolymers were 94.8 % for EPSs, 97.1 % for SA, 97.8 % for BSA, and 98.4 % for BSA-SA solutions. An evaluation model was proposed, incorporating the FO membrane's water permeability coefficient and the concentrated substances' osmotic resistance, to describe biopolymers' concentration properties. Irrespective of biopolymer type, the water permeability coefficient decreased with increasing osmotic pressure, remained constant with increasing feed solution (FS) concentration, increased with increasing crossing velocity in the draw side, and showed little dependence on draw salt type. In the EPS DEFO concentration process, osmotic resistance was minimally impacted by osmotic pressure, FS concentration, and crossing velocity, and monovalent metal salts were proposed as draw solutes. The interaction between reverse diffusion metal cations and EPSs affected the structure of the concentrated substances on the FO membrane, thus changing the osmotic resistance in the DEFO process. These findings offer insights into the efficient concentration of biopolymers using DEFO.

Green and Sustainable Forward Osmosis Process for the Concentration of Apple Juice Using Sodium Lactate as Draw Solution.

China is the world's largest producer and exporter of concentrated apple juice (CAJ). However, traditional concentration methods such as vacuum evaporation (VE) and freeze concentration cause the loss of essential nutrients and heat-sensitive components with high energy consumption. A green and effective technique is thus desired for juice concentration to improve product quality and sustainability. In this study, a hybrid forward osmosis-membrane distillation (FO-MD) process was explored for the concentration of apple juice using sodium lactate (L-NaLa) as a renewable draw solute. As a result, commercial apple juice could be concentrated up to 65 °Brix by the FO process with an average flux of 2.5 L·m-2·h-1. Most of the nutritional and volatile compounds were well retained in this process, while a significant deterioration in product quality was observed in products obtained by VE concentration. It was also found that membrane fouling in the FO concentration process was reversible, and a periodical UP water flush could remove most of the contaminants on the membrane surface to achieve a flux restoration of more than 95%. In addition, the L-NaLa draw solution could be regenerated by a vacuum membrane distillation (VMD) process with an average flux of around 7.87 L∙m-2∙h-1 for multiple reuse, which further enhanced the long-term sustainability of the hybrid process.

Technical Feasibility of Extraction of Freshwater from Produced Water with Combined Forward Osmosis and Nanofiltration.

This study assesses the technical feasibility of a forward-osmosis-based system for concentrating produced water and extracting freshwater. Forward osmosis was combined with nanofiltration, the latter system used to restore the initial osmotic pressure of the diluted draw solutions while concurrently obtaining the final freshwater product. Three draw solutions, namely, MgCl2, NaCl, and C3H5NaO2, were initially tested against a synthetic water mimicking a pretreated produced water effluent having an osmotic pressure equal to 16.3 bar. MgCl2 was thus selected for high-recovery experiments. Different combinations of draw solution osmotic pressure (30, 40, 60, 80, and 120) and draw-to-feed initial volume ratios (1, 1.6, and 2.2) were tested at the laboratory scale, achieving recovery rates between roughly 35% and 70% and water fluxes between 4 and 8 L m-2h-1. One-dimensional, system-wide simulations deploying the analytical FO water flux equation were utilized to validate the experiments, investigate co-current and counter-current configurations, and understand the system potential. The diluted draw solutions were then transferred to nanofiltration to regenerate their original osmotic pressure. There, the highest observed rejection was 96.6% with an average flux of 21 L m-2h-1, when running the system to achieve 100% relative recovery.

Metal-phenolic network as precursor complex coating for forward osmosis membrane with enhanced antifouling property.

In this study, a multi-functional layer was developed based on the commercially available cellulose triacetate (CTA) forward osmosis (FO) membrane to improve its antifouling property. Tannic acid/ferric ion (TA/Fe3+) complexes were firstly coated as a precursor layer on the membrane surface via self-assembly. Afterwards, the tannic acid/diethylenetriamine (TA/DETA) hydrophilic functional layer was further coated, following Ag/polyvinylpyrrolidone (PVP) anti-bacterial layer was formed in situ through the reducibility of TA to obtain TA/Fe3+-TA/DETA-Ag/PVP-modified membrane. The optimized precursor layer was acquired by adjusting the buffer solution pH to 8, TA/Fe3+ ratio to 4 and the number of self-assembled layers to 5. The permeability testing results illustrated that the functional layer had an insignificant effect on the membrane transport parameters. The TA/Fe3+-TA/DETA-Ag/PVP-modified membrane simultaneously exhibited excellent physical and chemical stability. The coated membrane also demonstrated enhanced anti-bacterial properties, achieving 98.63 and 97.30% inhibition against Staphylococcus aureus and Escherichia coli, respectively. Furthermore, the dynamic fouling experiment showed a 12% higher water flux decrease for the TA/Fe3+-TA/DETA-Ag/PVP CTA membrane compared to the nascent CTA membrane, which proved its excellent antifouling performance. This work provides a feasible strategy to heighten the antifouling property of the CTA FO membrane.

Optimized preparation route for polyamide top-coated forward osmosis membrane for enhanced water flux using industrial wastewater as feed.

The forward osmosis (FO) process has recently gained significant interest in treating wastewater, brackish/seawater and concentrating feedstocks for various operations, including desalination. The study investigates the effect of different synthesis conditions of the polyamide-based thin-film composite (TFC) FO membranes on the membranes' final performance. Taguchi statistical analyses were used to fabricate and optimize the polyamide TFC FO membrane. The process parameters as factors were the amount of polyethersulfone (PES), polyethylene glycol 400 (PEG-400), polyvinyl pyrrolidone (PVP), m-phenylenediamine (MPD), and trimesoyl chloride (TMC), and TMC reaction-time (RT). The Taguchi method was adopted to investigate the optimal conditions and the significance of individual factors using an L16 (45) orthogonal array. Another Taguchi analysis (Taguchi 2) was adopted to investigate the influence of other important parameters like optimal conditions for MPD, TMC, and TMC reaction-time factors using an L9 (33) orthogonal array. Confirmation tests validated a maximum water flux of 46.4 ± 2.32 L/m2·h with a specific combination of control factors for membrane synthesis: PES/PEG/PVP/MPD/TMC/TMC RT-16/7/0.5/1/0.05/30. These tests demonstrated a high-water flux of 7.05 ± 0.35 L/m2·h when exposed to industrial wastewater (secondary effluent) as the feed solution (FS) and fertilizer as the draw solution (DS) in the FO process. The R2 values were more than 90%. The experimental validation confirmed the models' predictive ability with different FSs, including industrial wastewater.

Concept and investigation of Selective Forward Osmosis (SFO) for Salt-Salt Separation as a Pretreatment of Seawater for Resource Utilization.

Seawater utilization is crucial for the sustainable human development. Despite growing interest in forward osmosis (FO) due to its unique properties, conventional FO membranes with salt-water selectivity have limitations in applying to specific salt-salt separation processes, which hinders their application in resource utilization. In this work, a new concept, "selective forward osmosis (SFO)", was proposed, which ingeniously employed an SFO membrane consisting of an ion-selective layer on a denser substrate. The denser substrate is designed to control water flux so as to alleviate the solution dilution and improve the salt-salt separation. Moreover, the sucrose and pure water were used separately as feed solution to provide different water flux to influence the various salt fluxes, showing that pure water feed could enhance the salt-salt separation efficiency, although it could dilute the draw solution to some extent. Therefore, pure water was selected as feed in the subsequent experiments. The optimized SFO membrane achieved high Na2SO4/NaCl selectivity (∼54.8) and MgCl2/NaCl selectivity (∼9.2) in single-salt draw solutions. With mixed-salt and heavy-metal-mixed-salt draw solutions, the Mg2+/Na+ selectivity was enhanced to ∼14.5, and further to 29.3. In real seawater tests, the SFO system effectively permeated monovalent elements (such as Na flux of ∼68.6 g m-2 h-1) while maintaining a higher rejection for bivalent elements (such as Mg flux of ∼0.08 g m-2 h-1), showing high selectivities for Mg/Na, U/Na, Sr/Na, Ni/Na, and Ca/Na. These results demonstrate the potential of SFO for resource utilization, especially in complex saline environments. This work contributes a new route for salt-salt separation in the pretreatment of seawater resources.

Perfluorooctanoic acid-contaminated wastewater treatment by forward osmosis: Performance analysis.

Perfluorooctanoic acid (PFOA) is a persistent compound, raising considerable global apprehension due to its resistance to breakdown and detrimental impacts on human health and aquatic environments. Pressure-driven membrane technologies treating PFAS-contaminated water are expensive and prone to fouling. This study presented a parametric investigation of the effectiveness of cellulose triacetate membrane in the forward osmosis (FO) membrane for removing PFOA from an aqueous solution. The study examined the influence of membrane orientation modes, feed pH, draw solution composition and concentration, and PFOA concentration on the performance of FO. The experimental results demonstrated that PFOA rejection was 99 % with MgCl2 and slightly >98 % with NaCl draw solutions due to the mechanism of PFOA binding to the membrane surface through Mg2+ ions. This finding highlights the crucial role of the draw solution's composition in PFOA treatment. Laboratory results revealed that membrane rejection of PFOA was 99 % at neutral and acidic pH levels but decreased to 95 % in an alkaline solution at pH 9. The decrease in membrane rejection is attributed to the dissociation of the membrane's functional groups, consequently causing pore swelling. The results were confirmed by calculating the average pore radius of the CTA membrane, which increased from 27.94 nm at pH 5 to 30.70 nm at pH 9. Also, variations in the PFOA concentration from 5 to 100 mg/L did not significantly impact the membrane rejection, indicating the process's capability to handle a wide range of PFOA concentrations. When seawater was the draw solution, the FO membrane rejected 99 % of PFOA concentrations ranging from 5 mg/L to 100 mg/L. The CTA FO treating PFOA-contaminated wastewater from soil remediation achieved a 90 % recovery rate and water flux recovery of 96.5 % after cleaning with DI water at 40 °C, followed by osmotic backwash. The results suggest the potential of using abundant and cost-effective natural solutions in the FO process, all without evident membrane fouling.

Experimental investigation and comparison of PBI/MWCNT and PSF/MWCNT membranes for recovering water from RO reject of brackish water by FO.

The performances of polybenzimidazole (PBI) and polysulfone (PSF) membranes for recovering water from reverse osmosis (RO) reject of brackish water through forward osmosis (FO) were assessed and compared. Non-functionalised multi-walled carbon nanotubes (MWCNT) were added to the membrane casting solutions, with concentrations ranging from 0 to 3 wt%. The experiment was conducted for eight samples using RO reject of brackish water as the feed solution (FS) and 2 M analytical grade MgCl2 as the draw solution (DS). The hydrophilicity, water permeability, salt rejection rate (Rs), water flux (WF) and porosity of the membranes improved with increasing MWCNT content up to 2 wt%. Also, the structural parameter, salt permeability and reverse solute flux decreased. PBI/MWCNT2 wt% exhibited the best performance among the membranes tested compared with porosity of 70 ± 4 %, structural parameter of 0.36 ± 0.2 µm, and Rs of 93.5 %. In contrast with the pristine PBI membrane, an average water flux enhancement of 15 % and 49 % was observed for the FS and DS sides, respectively, for PBI/MWCNT2 wt%. It is evident from the results that including MWCNT improves the performance of both membranes, with better relative performance for PBI membranes than PSF membranes.

Synthesis and characterization of an innovative sodium alginate/polyvinyl alcohol bioartificial hydrogel for forward-osmosis desalination.

Recently, hydrogels have been widely applied as draw agents in forward osmosis (FO) desalination. This work aims to synthesize bioartificial hydrogel from a blend of sodium alginate (SA) and polyvinyl alcohol (PVA) using epichlorohydrin (ECH) as a crosslinker. Then this prepared hydrogel was applied as a draw agent with cellulose triacetate membrane in a batch (FO) cell. The effects of the PVA content in the polymer blend and the crosslinker dose on the hydrogel's swelling capacity were investigated to optimize the hydrogel's composition. Furthermore, the water flux and the reverse solute flux of the optimum SA/PVA hydrogel were evaluated in a batch (FO) unit under the effect of the hydrogel's particle size, feed solution (FS) temperature, FS concentration, and membrane orientation. Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD) and compression strength tests were used to characterize the prepared hydrogel. Results revealed that the equilibrium swelling ratio (%) of 5228 was achieved with a hydrogel that had 25% PVA and a crosslinking ratio of 0.8. FO experiments revealed that the maximum water flux of 0.845 LMH achieved, when distilled water was used as FS, average hydrogel's particle size was 60 µm, and the FS temperature was 40 °C.

Impact of temperature and forward osmosis membrane properties on the concentration polarization and specific energy consumption of hybrid desalination system.

This study investigates how temperature and forward osmosis (FO) membrane properties, such as water permeability (A), solute permeability (B), and structural parameter (S), affect the specific energy consumption (SEC) of forward osmosis-reverse osmosis system. The results show that further SEC reduction beyond the water permeability of 3 LMH bar-1 is limited owing to high concentration polarization (CP). Increasing S by 10-fold increases FO recovery by 177.6%, causing SEC decreases by 33.6%. However, membrane with smaller S also increases external CP. To reduce SEC, future work should emphasize mixing strategies to reduce external CP. Furthermore, increasing the temperature from 10 to 40 °C can reduce SEC by 14.3%, highlighting the energy-saving potential of temperature-elevated systems. The factorial design indicates that at a lower temperature, increasing A and decreasing S have a more significant impact on reducing SEC. This underlines the importance of developing advanced FO membranes, particularly for lower-temperature processes.