Large scale screening and quantification of micropollutants in fish from the coastal waters of Cochin, India: Analytical method development and health risk assessment.

Urban estuarine and coastal water receive several micropollutants through industrial and agricultural influxes. The bioaccumulation of these micropollutants in fish and their entry into the coastal population's food chain raises significant food safety concerns. Hence, a comprehensive analytical method was developed for ultra-trace level quantification of 345 micropollutants in fish. The optimized sample preparation method could extract compounds suitable for both GC-MS/MS and LC-MS/MS analysis simultaneously. The target list of contaminants included 278 agricultural pesticides and also 102 endocrine disruptors covering polyaromatic hydrocarbons, polychlorinated biphenyls, organochlorines, and endocrine-disrupting pesticides. The GC-MS/MS with large volume injection (LVI) technique, and LC-MS/MS operating in MRM mode, achieved an LOQ of <2.00 ng/g for most of the analytes. The extraction strategy involved tri-phase partitioning between water, acidified acetonitrile, and hexane, followed by salting out. Dispersive solid phase cleanup (dSPE) with C18, Z-Sep+, CaCl2, and MgSO4 was able to reduce the matrix influence, and the method achieved satisfactory recovery in the range of 70.0-120.0 % for all the target analytes. The repeatability and reproducibility relative standard deviation values of the measured analytes were <20.0 %, and the Horwitz ratio values were well below 2. The method was used to accurately measure the target micropollutants in fish from the Cochin estuary, the highly urbanized portion of the Vembanad Lake, and an important Ramsar site. At least one or more of the 41 different micropollutants were identified and quantified in about 90.7 % of the 108 samples analyzed. The importance of large-scale screening and trace-level quantification methods in environmental monitoring and risk assessment is underscored by the results. The risk assessment showed a moderate risk of exposure to the nearby coastal population through the food chain.

Microplastic assessment in remote and high mountain lakes of Gilgit Baltistan, Pakistan.

Microplastic (MP) pollution is a critical environmental challenge worldwide, however limited research is reported in remote lakes of Pakistan. This study assessed MPs (>5 mm) prevalence, distribution and risk perspective in water and sediment of eight remote and high-altitude lakes (>1500 m above sea level) of Gilgit Baltistan, Pakistan. The lakes exhibited an average abundance of 152.6 ± 104.6 to 12.1 ± 7 MP/kg of dry sediments and 2 ± 0.9 to 17.1 ± 17.2 MP/L of surface water. MPs <200 µm dominated in both matrices. Surface water predominantly contained polyester and polypropylene, while polypropylene and polyethylene dominated in sediments. The gradient of elevation did not show any pronounced impact on the fiber loading or MP count in both matrices. Backward air mass trajectory revealed that air masses vastly travelled from western-Asia, Arabian sea and Bay of Bengal with an average transmission distance of 2500-3500 km (500 m a.s.l) that can be a potential deposition MP source in the area. Pollution Load Index of the lakes were >1 exhibiting pollution. All other lakes except Batura and Borith manifested a moderate hazard index. Naltar lake along with aforementioned two lakes also manifested high polymer toxicity. Further research should emphasize understanding the mechanisms and biotic interactions in high-mountain ecosystems.

Assessing water quality and human health risk near coal mines and industrial area of Singrauli, India: special emphasis on toxic elements.

Water contamination is a major environmental issue, especially in rapidly growing industrialized areas like Singrauli. This study addresses research gaps regarding the hydrochemical characterization, health risk assessment, and source identification of contaminants. Hydrochemistry shows the concentrations of Na+, Ca2+, F-, Mn, As, Mo, Sr, and Ni were above the permissible limit for drinking usage. Water quality index (WQI), heavy metal pollution (HMPI), and evaluation indices (HMEI) revealed As, Mn, Cd, Mo, Co, and Ni were the key heavy elements contributing towards aqueous media pollution in the Singrauli area. Additionally, F was also considered one of the major contaminants. In health risk assessment, the higher values of hazard quotient (HQ) for non-carcinogens were associated with Mn, As, Mo, and F; and hazard index (HI) values > 1 were found in 70% and 55% of samples for children and adults, respectively. Carcinogenic risk (CR) for human health was associated with As. CR values in 56.7% (for adults) and 61.7% (for children) of the total samples exceeded 1 × 10-4. Monte Carlo simulation was applied and highlighted the significant risk factors responsible for both carcinogenic and non-carcinogenic health impacts. 19.2%, 7.3%, and 6.9% of the simulated HQ values for adults and 30.1%, 16.9%, and 10.6% for children were above the safe limit for F, As, and Mn, respectively. Additionally, only 43.8% and 24.8% of the simulated HI for adults and children were within the safe limit. Irrespective of age groups, all the simulated values of As in CR were above 1 × 10-6; and 60% (for adults) and 77.1% (for children) of the values were above 1 × 10-4. This outcome emphasizes the urgency of pollution control measures, especially for As, F, and Mn, to safeguard public health. Moreover, a multivariate statistical approach revealed that both geogenic and anthropogenic sources were responsible for contamination. Therefore, regular monitoring, filtration, and purification are mandatory to ensure safe drinking water for human consumption.

Estimation of the Dietary Acrylamide Exposure of the Turkish Population: An Emerging Threat for Human Health.

Acrylamide is a contaminant formed during heat treatment that poses potential health risks and occurs naturally in foods. Therefore, it is crucial to evaluate exposure from the consumption of foods containing acrylamide since dietary exposure continues throughout life. In this study, the acrylamide exposure level of people living in Türkiye is estimated. Consumption of a total of 28 foods in 9 different food groups was calculated using a deterministic model under two different scenarios. The exposure levels were evaluated in terms of carcinogenic, non-carcinogenic and neurotoxic health risks. The daily total acrylamide exposure levels of individuals aged 15 and older were determined as 58 µg/day (0.85 µg/kg bw/day) and 196 µg/day (2.80 µg/kg bw/day) for the good and bad scenarios, respectively. The highest daily acrylamide exposure in the good scenario came from brewed black tea (29%), whereas French fries (50%) were the source of highest daily acrylamide exposure in the bad scenario. According to the hazard index (HI) and margin of exposure (MOE) data, the good scenario (all food) is considered safe, while the bad scenario (all food) has potential and serious health risks. According to the carcinogenic risk (CR) data, both scenarios carry significant health risks. It is therefore important that consumers, producers and official institutions collaborate and take measures to reduce acrylamide exposure.

Exposure assessment of pesticide residues, heavy metals, and veterinary drugs through consumption of Egyptian fish samples.

Environmental contaminants may enter seafood products either through water and sediments or via feed and feed additives or may be introduced during fish processing and storage. The study focused on the nutritional and toxicological significance of heavy metals, antibiotics, and pesticide residues in 48 fish samples collected from the Kafr-ElSheikh governorate in Egypt. Various analytical instruments are used to determine and detect heavy metals, antibiotics, and pesticides. These include Liquid Chromatography Tandem Mass Spectrometer (LC-MS/MS), Inductively Coupled Plasma Mass Spectrometer (ICP-MS), and Gas Chromatography-Mass Spectrometer (GC-MS). The following metals were discovered in fish species: arsenic (As), cadmium (Cd), cobalt (Co), copper (Cu), iron (Fe), mercury (Hg), manganese (Mn), and zinc (Zn). Each of these metals was detected 47 times. Chromium (Cr) was detected 40 times, nickel (Ni) was detected 27 times, and lead (Pb) was detected 6 times. The mean concentrations of As, Cd, Cr, Co, Cu, Fe, Ni, Mn, Hg, Pb, and Zn were determined to be 0.025, 0.02, 0.501, 0.50, 0.81, 12.56, 0.5, 0.689, 0.051, 0.031, and 5.78 mg/kg, respectively. All levels of cadmium, mercury, and lead detected in fish samples were significantly lower than the maximum permissible limits set by Egyptian and European standards. Furthermore, in this study, antibiotics and pesticide residues were found to be not detected in all analyzed fish samples. Based on the estimated daily intake and hazard quotient values, the concentration levels of metals found in fish samples seem to pose no significant threat to public health.

Human health risk assessment on pesticide residues in fishes of kuttanad wetland, a globally important agricultural heritage system.

Kuttanad is a unique wetland agriculture system featuring polder-based rice cultivation below sea level. Facing increasing pollution threats from agrochemicals, this FAO-recognized Globally Important Agricultural Heritage System (GIAHS) needs constant monitoring and risk assessment. The present study investigated the seasonal dynamics of agricultural pesticide residues in fish cultured in the wetland system. A total of 217 fish samples were analyzed, spanning three different sampling stations of Kuttanad, viz., Vaikom, Ramankari, and Edathua, during pre-monsoon, monsoon, and post-monsoon seasons. The results revealed the presence of 14 pesticides across locations and seasons. The pesticides found in the highest concentrations were propetamphos (54.64 mg L-1), thiacloprid (46.78 mg L-1), and diphenylamine (24.70 mg L-1). The most frequently detected pesticides were propoxur, fenuron, and thiacloprid. Contaminants were detected more frequently during the post-monsoon season (49%) compared to the monsoon (38%) and pre-monsoon (13%) seasons, with imidacloprid being present in all three seasons. The target hazard quotients (THQ) for propetamphos, thiacloprid, and diphenylamine were determined to be 0.04, 0.004, and 0.0002, respectively. The hazard index (HI) calculated as the sum of THQ of quantified pesticides was 0.056, indicating a low to moderate risk. However, consistent monitoring of pesticides in the Kuttanad wetland agriculture system is important to ensure timely intervention to protect biodiversity and human health.

Heavy Metal Biomonitoring in Cultured Rainbow Trout of the Black Sea and Risk Estimations on Its Consumption.

In recent years, the growing importance of fish species obtained through aquaculture, coupled with a decline in wild-caught fish, has raised concerns about the potential accumulation of pollutants in these fish. This work aimed to analyze the amounts of elements in trout cultured mainly between Sinop and Samsun shores at the south of the Black Sea and marketed in Sinop fish markets. The comparison of these values with national and internationally accepted regulations was conducted, and evaluation of health risks for consumers was performed. Oncorhynchus mykiss samples were bought in April, May, and June of 2022 and 2023. The heavy metal concentrations were determined using inductively coupled plasma mass spectrometry (ICP-MS). Fish tissues were wet digested in Teflon vessels. The outcomes were contrasted with established regulatory limits for heavy metals in fish. Fortunately, the metal concentrations detected in the fillets were found to be below the permissible levels set by regulations, indicating that the fish were not significantly contaminated. Furthermore, the estimated daily intake (EDI) and target hazard quotient (THQ) values, which are utilized to evaluate the possible health risks connected with heavy metal exposure, were calculated. It was reassuring to find that both EDI and THQ values were below the acceptable thresholds, suggesting that the consumption of O. mykiss is not likely to pose a threat to human health. To preserve seafood safety and safeguard public health, however, constant monitoring of fish metal levels is necessary.

Spatiotemporal variations, source identification, and risk assessment of potentially toxic elements in the surface water of Felent Stream impacted by the silver mine.

The silver deposits located in the upper basin of the Felent Stream are currently the largest producing mine in the Türkiye. It is also significantly impacted by industrial, agricultural, and thermal spring-related waste in Kütahya Province. The main objectives of this study were to examine the spatiotemporal variations of 12 dissolved potentially toxic elements (PTEs) in the surface water of Felent Stream, to identify their possible sources, and to assess their probable risks. As a result of this study, among investigated PTEs, the highest mean concentrations of 3592-14,388 µg/L for Mg and the lowest of 0.15-0.19 µg/L for Cd were noted in Felent Stream water. The average concentrations of PTEs were found in the order of Mg > Ca > Na > As > Mn > B > Zn > Ni > Cu > Pb > Cr > Cd. Remarkably, during the dry season, there was a conspicuous escalation in the average PTEs contents of water, with an approximately multifold amplification. PTEs in stream water were evaluated for their potential ecotoxicological risks and possible sources. Based on ecological risk assessment indices, the stream exhibited low pollution levels during the wet season but displayed elevated pollution levels during the dry season, indicating a general shift towards heightened pollution conditions. The hazard index (HI) data for As exhibited significant potential noncarcinogenic risks across all monitoring stations. Conversely, the carcinogenic risk (CR) data underscored the imperative nature of addressing the health risks associated with As in the waters of the studied region. Mining activities were identified as the primary origin of PTEs based on principal component analysis (PCA). Moreover, upstream regions, proximal to the mining site, emerged as the most heavily contaminated areas according to cluster analysis (CA).

Health Risk Assessment of Toxic Metal(loids) Consumed Through Plant-Based Anti-diabetic Therapeutics Collected in the Northern Divisional City of Rajshahi, Bangladesh.

The present study investigates human health risks upon consumption of herbal medicines in terms of ten toxic metalloids in 20 plant-based anti-diabetic therapeutics. The analysis of metalloids was determined by an atomic absorption spectrometer after microwave-assisted digestion. The computation of hazard quotients (HQ) and hazard indexes (HI) of metalloids leads to the assessment of non-carcinogenic health risks. Carcinogenic risk was assessed based on cancer slope factor (CSF) and chronic daily intake (CDI) values. Comparison with WHO regulatory cut-off points for each metalloid: seven samples for Mn, 12 samples for Hg, three samples for Cu, eight samples for Ni, four samples for Cd, two samples for Pb, one sample for Cr, and eight samples for Zn are unsafe to consume. Non-carcinogenic human health risk is predicted for Mn in seven samples, Fe in one sample, Hg in ten samples, Cu in three samples, Ni in one sample, and Pb in two samples. HI values greater than 1 predict non-carcinogenic health risk in thirteen samples. Incremental lifetime cancer risk (ILCR) remains for As (inorganic) in 12 samples, Cr (+ 6) in one sample, and Pb in no samples. To guarantee consumer safety, the implementation of strict monitoring is suggested.

Carcinogenic and non-carcinogenic health risk assessment of heavy metals in the offal of animals from Felele Abattoir, Lokoja, Nigeria.

The consumption of metal-contaminated offal of animals will affect the health of humans. Thus, the research determined the concentrations of heavy metals in the offal and muscle tissues of cows, goats, and ram slaughtered at the main abattoir in Lokoja, northcentral Nigeria. Furthermore, an evaluation was carried out to assess the potential health hazards faced by the indigenous population due to the consumption of heavy metals from these animals. The mean concentrations of metals (Al, Cd, Cr, Ni, and Pb) in the kidney, liver, and muscle of cows, goats, and rams were determined using Inductively Coupled Plasma Optical Emission Spectrometry. Estimated daily intake of the metals, hazard quotient, hazard index, and cancer risk were calculated. All internal organs had Ni levels above the regulatory threshold limit. The average concentration of Pb in the muscle tissue and liver of the tested animals exceeded the permissible limits by the WHO. Similarly, the concentration of Cd in the muscle tissues was above the Maximum Permissible Limit (MPL) of 0.05 mg kg-1. Except for cow kidneys, all internal organs contain Cr levels below the MPL (1.0) limit. The THQ value for the metals was < 1 except Cd. It indicates potential health risks due to Cd. The calculated HI values were > 1. The percentage contribution of Cd to the HI value was the highest. The observed sequence is Cd > Ni > Cr > Pb > Al. The results show that eating the offal and muscle under investigation has a carcinogenic effect.

Microplastic assessment in aquaculture feeds: Analyzing polymer variability across commercial fishfeeds from three continents.

This study analysed ten widely used commercial fishfeeds in aquaculture from six countries spanning three continents to assess microplastic (MP) contamination. MPs with an average abundance of 1130 ± 259.07 particles/kg and an average length of 2.64 ± 0.62 mm ( ± SE) were found in aquaculture feeds, with fibres (85 %) and fragments (15 %). The majority of these MPs were black. The abundance of MPs varied among the samples, with the highest in feed SP (26 %), followed by IF, GA, ELS, NT, EW, TB, GR, VR, and the least in HCF (3 %). Polymers identified consisted of Polyethylene terephthalates (PET, 20 %), Polyamide (PA, 30 %), Polymethyl methacrylate (PMMA), Polyurethane (PU), and Polystyrene (PS) with 15 % each, and Polypropylene (PP, 5 %). SEM-EDX analysis of fibres showed flakes, cracks, and pits and the presence of heavy metals Ni, Cu, Zn, Cr, Au, Hg, Cd, Ti, and Pb. Additionally, some fragments contained Nb (Niobium) alongside the naturally occurring elements. The Polymer Hazard Index (PHI) for the polymers in ten feeds was calculated, and nine were in the highly hazardous category (IV and V) with PHI values ranging from 400-394825. The work showcases the graveness of MPs in fishfeeds and advocates control measures to curtail MPs in fishfeeds for sustainable aquaculture production.

Groundwater quality in high-sulfur coal mining region of India: Spatial distribution, source control, and health risk assessment.

The groundwater quality in the vicinity of the Makum coalfield, renowned for its high-sulfur coal deposits, was investigated. The oxidation of sulfur in the coal generates acid mine drainage (AMD), a global environmental challenge that contaminates natural resources. The region's high sulfur coal content intensifies AMD formation, necessitating a comprehensive assessment of its impact on human health and the environment. This study analyzes the water quality parameters such as pH, EC, TDS, Na+, Ca+2, Mg+2, K+, HCO3-, SO4-2, F-, Cl -, and NO3- in groundwater, findings concerning low pH levels (5.8) and fluoride concentration (0.15 mg/L) compared to standards. Groundwater chemistry was analyzed to identify the sources controlling water composition through Gibbs diagrams, Piper diagrams, and saturation indices. The Gibbs diagram shows that rock weathering is the crucial factor controlling groundwater chemistry, while the Piper diagram indicates Ca-Cl as the Principal water type. Additionally, an in-depth analysis of groundwater chemistry reveals that carbonate dissolution primarily occurs due to minerals like calcite, dolomite, and gypsum, findings supported by saturation indices. The present study yielded an average water quality index of 40.19, indicating excellent to good water quality in 51 out of 52 samples analyzed. The average hazard index values for adults and children were 0.60 and 0.58, respectively, indicating that 49 of 52 samples pose negative non-carcinogenic risks associated with nitrate and fluoride contamination. The irrigation indices, graphical representations such as the Wilcox and Doneen classification, and the USSL diagram elucidate the suitability for irrigation purposes. Moreover, the Principal Component Analysis identified the sources of ions as originating from geogenic processes and mining activities. The study stresses environmental assessments, health risk management, and sustainable practices for groundwater in high-sulfur coal mining areas.

Concentration and health risk assessment of per- and polyfluoroalkyl substances in cosmetic and personal care products.

Per and polyfluoroalkyl substances (PFAS) are toxicologically concerning because of their potential to bioaccumulate and their persistence in the environment and the human body. We determined PFAS levels in cosmetic and personal care products and assessed their health risks. We investigated the trends in concentrations and types of PFAS contaminants in cosmetic and personal care products before and after perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA) were added to the list of persistent organic pollutants. The total PFAS concentration ranged from 1.98 to 706.75 ng g-1. The hazard quotients (HQs) for PFOA, PFOS and perfluorobutanesulfonic acid (PFBS) were lower than 1, indicating no appreciable risk to consumers. Assuming the simultaneous use of all product types and the worst-case scenario for calculations, perfluoroalkyl carboxylic acids and perfluoroalkane sulfonic acids (PFSAs) also had hazard indices lower than 1. We found that adverse effects are unlikely to occur when each type of cosmetic is used separately, or even when all product types are used together. Nevertheless, the persistence and bioaccumulation characteristics of additional PFAS present in cosmetics continue to be a cause for concern. Further research is necessary to investigate the long-term impacts of using such cosmetics and the associated risks to human health.

Nutritional and toxicological assessment of Piliostigma thonnigii leaves and Tubaani food samples: a preliminary investigation.

Tubaani is a local delicacy prepared with Piliostigma thonningii leaves. The leaves may contain trace/heavy metals and important phytonutrients that could impact consumers' health. Concerns over the nutritional and toxicological implications of Piliostigma thonningii leaves are critical. Tubaani food and Piliostigma thonningii leaf samples were investigated using Neutron Activation Analysis (NAA) and Spectrophotometry technique. The health risk of Tubaani was also assessed by calculating the target hazard quotient (THQ) and hazard index (HI) of potentially toxic elements. Fifteen trace elements were detected at non-toxicological concentrations in the samples analyzed. No significant difference (p > 0.05) was observed between the samples' mean concentrations. The phenolic content in leaf extracts was higher as compared to the flavonoids. However, the flavonoids in the leaves had an effect on the food samples, unlike the phenols. The THQ and HI of the elements were below 1.0. There is no reason to be concerned about the current dietary intake of the potentially toxic elements in the routine consumption of Tubaani as portrayed in data obtained in this investigation by NAA, THQ, and HI.

Spatial variations and health risk assessment of heavy metal levels in groundwater of Qatar.

The present work's objective is to give a comprehensive overview of the quality of groundwater in Qatar in terms of heavy metals content as well as investigating the cause and effect of the elevation in their levels above the WHO/US-EPA standards. The scope of the study included (1) physical and chemical analysis of 82 groundwater samples collected from various locations around Qatar, (2) development of ArcGIS maps depicting the variations in the levels, (3) assessment of the human health risks associated with the existing levels using three of the most used models which are: Hazard index (HI), Nemerow comprehensive pollution index (NCPI) and Incremental Lifetime Cancer Risk (ILCR). There is no extensive study ever reported to assess the health risks linked with the consumption of groundwater characterized with such heavy metals levels in Qatar. The chronic daily intake (CDI) of the investigated heavy metals (Ag, Mn, Cr, V, Mo and Sr) through ingestion and dermal pathways had a range of 1.4 × 10-5-6.7 × 10-1 mg/kg/day while the NCPI's range was reported at 0-4.39. Moreover, the HI and ILCR were found to have a range of 0-3.2 and 5.6 × 10-4-5.5 × 10-2, respectively. The assessment of health risks, conducted in the present work, could be beneficial in building the baseline of heavy metals levels in groundwater in Qatar. This will also help in the determination of any future contamination of groundwater.

Comprehensive index analysis approach for ecological and human health risk assessment of a tributary river in Bangladesh.

This study examined the water quality of the Turag River, an important tributary river in Dhaka, Bangladesh in terms of physicochemical characteristics and heavy metal contamination to assess the potential risks to both ecological systems and human health. The majority of the water samples complied with the acceptable limits established by the World Health Organization (WHO) for various parameters including pH, electrical conductivity (EC), total dissolved solids (TDS), dissolved oxygen (DO), chemical oxygen demand (COD), sodium adsorption ratio (SAR), and magnesium adsorption ratio (MAR), except total hardness (TH). The sodium (Na), potassium (K), calcium (Ca), magnesium (Mg), chloride (Cl-), fluoride (F-), nitrate (NO3 -), and sulfate (SO4 2-) levels in the water samples were found to be within acceptable ranges for most cases. Moreover, heavy metals including lead (Pb), cadmium (Cd), chromium (Cr), nickel (Ni), iron (Fe), manganese (Mn), zinc (Zn), copper (Cu), arsenic (As), selenium (Se), and mercury (Hg) were analyzed and their mean concentrations (µg/L) were found in the order of Fe (244.72 ± 214.35) > Mn (28.93 ± 29.64) > Zn (22.97 ± 10.93) > Cu (8.28 ± 5.99) > Hg (8.23 ± 6.58) > As (1.34 ± 0.39) > Ni (1.20 ± 0.38) > Cr (0.67 ± 0.85) > Pb (0.61 ± 0.72) > Se (0.42 ± 0.48) > Cd (0.13 ± 0.09) which were within the acceptable limit, except Hg. The cumulative effect of all heavy metals was assessed through the heavy metal pollution index (HPI), contamination degree (Cd), and nemerow pollution index (PN). The mean value of HPI (682.38 ± 525.68) crossed the critical index value of 100, indicating an elevated level of pollution. The mean value of Cd (8.763 ± 6.48) indicates a low-moderate-significant level of contamination due to an elevated level of Hg, and for the PN it was found 174.27 ± 146.66, indicating a high level of pollution due to high level of Fe. Ecological risk index (ERI) indicated low levels of risk for Pb, Cd, Cr, Ni, Fe, Mn, As, Se, Cu, and Zn but a significantly high risk for Hg. The water was classified as good to excellent based on its physicochemical properties (pH, EC, TDS, COD, DO, F-, Cl-, NO3 -, and SO4 2-) while it was deemed poor to unsuitable for heavy metals according to the water quality index (WQI). Among the carcinogenic constituents, As poses the greatest carcinogenic risk, particularly for children. The mean value of Cr, Mn, and As in the HQingestion for adult and child, and Cd, Hg for child exceeded the threshold value established by the United States Environmental Protection Agency (USEPA), while the HQdermal values remained below the maximum limit for all heavy metals. The value of HI at all locations exceeds the threshold of 1, as specified by USEPA. Principal component analysis (PCA) and cluster analysis revealed that the presence of heavy metals in the Turag River was mainly attributed to anthropogenic sources, including industrial effluent discharge from neighboring industries, domestic wastewater, and agricultural runoff containing agrochemicals from the surrounding lands.

First occurrence and risk assessment of microplastics in enteral nutrition formulas.

Occurrence and characteristics of microplastics were evaluated in enteral nutrition formulas, for the first time. A total of 30 samples belonging to 9 brands were analysed. Physical and chemical characteristics of microplastics were identified by stereomicroscopy and micro-raman spectroscopy, respectively. The mean number of microplastics was 45 ± 63 MP/L. Two different shapes of microplastics were detected with fibres (62%) being the most common microplastics followed by fragments (38%). The most common color of microplastics was black (37%) followed by blue (26%), orange (15%), green (7%), red (7%), grey (4%) and multicolor (4%). The length of microplastics ranged from 10 to 2086 µm with an average of 548 ± 526 µm. Estimated mean daily microplastic intake for four different scenarios varied between 24 to 61 and 30 to 76 MPs/day for women and men, respectively. The mean polymer hazard index and microplastic load index levels were calculated as 380 and 1.30, respectively. The results of this study showed that microplastics are prevalent in enteral nutrition products. The presence of polymers with high hazard risk scores in enteral nutrition formulas may pose a risk to the health of patients with special nutritional needs.

Occurrence of microplastics in store-bought fresh and processed clams in Italy.

Compared to the large amount of data on wild samples, only a few studies reported microplastic occurrence in store-bought bivalves in which the production chain can be the main contamination route. Microplastic occurrence was herein investigated in 100 samples of store-bought clams sold as fresh or processed (vacuum-frozen or in brine) in Italy. A 10 % KOH was used for soft tissue digestion and FT-IR spectroscopy for polymer identification. A total of 135 potential microplastics ranging in size between 20 µm and 5000 µm were enumerated estimating an annual dietary intake via clam consumption of 59.472 microplastics/person. No significant difference in the average abundance between the two commercial conditions was observed, while a prevalence of smaller particles was detected in processed samples suggesting a detrimental effect of cooking during production. Polyethylene (PE), polyethylene terephthalate (PET), and polystyrene (PS) were identified posing an overall low risk (class II). Microplastic occurrence in store-bought seafood requires additional and specific attention and future studies should investigate microplastic contribution linked to the production chain.

Diet characteristics of tidal creek-associated fishes of the northeastern Arabian Sea with special reference to microplastic ingestion.

The present study assessed the diet characteristics, trophic guild structure, and microplastics (MPs) ingestion by a group of fish sourced from the tidal creeks of the Mumbai coast along the Eastern Arabian Sea. The diet patterns were characterized using gastro-somatic index (GaSI), relative length of gut (RGL), diet overlap (α), diet breadth (Bi), and relative abundance of food items (%IOP), with a special emphasis on MPs contamination. The findings revealed that teleost and shrimps are the most preferred food items for these species. Whereas MPs contribute 5.50% of the total diet composition of the selected fishes. Additionally, we tried to find out the influence of fish size and dietary attributes on MP ingestion, identifying trophic level as a significant factor influencing contamination levels. Using the Polymer Hazard Index (PHI), the potential risks posed by MPs in fish samples were assessed, revealing notable discrepancies among polymers. For instance, polyvinyl chloride showed the highest PHI score of 198.75 and a hazard score reaching the highest risk category (IV), indicating substantial environmental risk. In summary, our findings highlight the impact of fish diet characteristics on MPs contamination and the varying levels of MP risks along the Mumbai coast, categorized according to polymer type from low to high risk.

Ecological and human health risk associated with heavy metals (HMs) contaminant sourced from petroleum refinery oily sludge.

The environmental and human health risk of heavy metals (HMs) in petroleum based oily sludge (OS) varies depending upon the source of origin of the crude oil and treatment processes practiced at the refineries. Consequently, the present study explores the potential risk associated with HMs of OS obtained from different refinery sites to the environment and human health. The results showed that HMs (Cu, Ni, Zn, Mn) present in OS surpasses the permissible limit of WHO guidelines except for Cr. Additionally, the Igeo value (grade 3-6), Ef (2.48-121.4), PLI (5.12-22.65), Cd (32.48-204.76) and PERI (grade 1-5) confirmed the high level of HMs contamination into the OS and its risk to the environment. Besides, the hazard index (HI) and the total carcinogenic risk (TCR) for HMs show substantial risk to both adult and children health. Likewise, the G-mean enzyme index and potential soil enzyme risk index (PSERI) of the OS showed a high risk to soil biological properties. Furthermore, statistical analysis confirmed the heterogeneity in properties of the OS and its potential impact on the soil ecosystem arising from different sites. Finally, the study unveils a novel perspective on the environmental and human health consequences associated with the OS.