[Determination of three dechloranes in environmental water by magnetic solid-phase extraction-gas chromatography-negative chemical ionization mass spectrometry based on the covalent organic framework material].

Dechloranes are additive-type chlorine flame retardants that are widely used in processing industrial products, such as electronic equipment and textiles. Dechloranes, which can enter the human body through various routes, pose significant health risks because of their toxicity, persistence, and bioaccumulation. In 2023, dechlorane plus was listed in the Stockholm Convention on Persistent Organic Pollutants. In the same year, China recognized this compound as a priority-controlled substance. Dechloranes are commonly found at trace levels in water, which is extremely harmful to the environment and human health. Therefore, the development of detection methods for dechloranes is crucial. Magnetic solid-phase extraction (MSPE) has attracted considerable attention because of its low organic solvent consumption, simplicity of adsorbent separation, and ease of operation. In general, the selectivity and efficiency of MSPE depend on the characteristics of the adsorbent. Covalent organic frameworks (COFs) have regular porosity, structural predictability and stability, high specific surface areas, and adjustable pore sizes, which are advantageous for a wide range of separation and analysis applications. In this study, Fe3O4 magnetic nanoparticles and a COF material (TpBD) were combined to prepare Fe3O4@TpBD as an adsorbent for dechloranes. Subsequently, an effective method for analyzing dechlorane in environmental water was established by coupling MSPE with gas chromatography-negative chemical ionization mass spectrometry (GC-NCI/MS). The successful synthesis of Fe3O4@TpBD was confirmed using transmission electron microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, and vibrating sample magnetometry. A single-factor method was used to optimize the extraction conditions, including the Fe3O4@TpBD dosage, pH of water sample, elution solvent type and volume, extraction time, elution time, and ionic strength. The target analytes were separated on a TG-5SILMS column (30 m×0.25 mm×0.25 µm) and quantified using the external standard method in the selected-ion monitoring (SIM) mode. Under the optimal extraction conditions, the method validation results showed a linear range of 2-1000 ng/L. The limits of detection (LODs) and quantification (LOQs) were 0.18-0.27 ng/L and 0.60-0.92 ng/L, respectively, for the three analytes. The intra-day and inter-day precisions at three spiked levels were 4.2%-16.2% and 6.9%-15.7%, respectively. This method was successfully applied to the determination of dechloranes in environmental water samples (laboratory tap water, reservoir water, wastewater treatment plant effluent, and landfill leachate treatment effluent). The recoveries of the three dechloranes at different spiked levels ranged from 77.8% to 113.3% with relative standard deviations (RSDs) of 2.5%-16.3% (n=3). With the advantages of operational simplicity, high sensitivity, and good reproducibility, the proposed method is suitable for the qualitative and quantitative determination of dechloranes in environmental water.

Novel pillar[n]arenes magnetic nanoparticles: Preparation and application in quantitative analysis of trace perfluorinated compounds from aqueous samples.

BACKGROUND: Perfluorinated compounds (PFCs) are a class of widely manufactured and used emerging persistent pollutants. The recent discovered new class of macrocycles pillararenes have garnered significant attention for the applications in environmental pollutant adsorption, with abundant π electron cavities, a symmetrical rigid structure, and host-guest recognition capabilities. RESULTS: In this work, we designed and synthesized novel cationic pillar [n]arenes magnetic nanoparticles (CWPA5@MNPs), and investigated its adsorption performance and mechanism as a type of new adsorbent for the enrichment of PFCs. The results indicate that CWPA5@MNPs exhibits selectively strong affinity for perfluorooctane sulfonate (PFOS) and long-chain (C9-C14) perfluorocarboxylic acids (PFCAs), with the adsorption efficiency exceeding 80 % within 12 min. The maximum adsorption capacity of CWPA5@MNPs for PFOS was measured to be 29.02 mg/g. CWPA5@MNPs can be rapidly isolated from the solution using external magnets, offering a quick and easy separation. Consequently, this study established a CWPA5@MNPs-assisted magnetic solid-phase extraction (MSPE) coupled with high-performance liquid chromatography-tandem mass spectrometry (CWPA5@MNPs-MSPE-HPLC-MS/MS) method for the rapid detection of trace levels of PFCs in environmental water samples. The analysis of 7 PFCs yielded recovery rates ranging from 86.1 % to 107.5 %, with intraday and interday relative standard deviations (RSD) of 3.6-6.4 % and 1.3-7.0 %, respectively. SIGNIFICANCE AND NOVELTY: The study reveals the synthesis and application of novel cationic pillar [n]arenes magnetic nanoparticles (CWPA5@MNPs) as highly efficient adsorbents for selective perfluorinated compounds (PFCs) in water samples. It demonstrates the potential of the newly developed CWPA5@MNPs-MSPE-HPLC-MS/MS method for the quantitative analysis of PFCs in environment, with high sensitivity, accuracy and stability.

A novel zwitterionic magnetic nanocomposite developed for non-invasive speciation analysis of inorganic chromium.

3-(2-Aminoethylamino)propyltriethoxysilane and carboxyethylsilanetriol sodium salt were grafted on silica-coated Fe3O4 nanoparticles via sol-gel process to prepare novel amine- and carboxyl-bifunctionalized magnetic nanocomposites (SMNPs-(NH2 + COOH)). After well characterized, this doubly functionalized material was used as magnetic solid-phase extraction (MSPE) adsorbent to separate and enrich inorganic chromium species followed by inductively coupled plasma-mass spectrometry detection. The optimization of MSPE operation parameters including pH was conducted. It is reasonably elucidated that the adsorption mechanisms of zwitterionic SMNPs-(NH2 + COOH) towards chromium species are electrostatic and/or coordination interactions. Cr(VI) and Cr(III) can be adsorbed around pH 3.0 and around 10.0 respectively with strong anti-interference ability not only from other co-existing ions but also from the two labile species each other, and eluted by dilute nitric acid solution. With a 15-fold enrichment factor, the limits of detection of Cr(VI) and Cr(III) were 0.008 and 0.009 µg L-1, respectively, profiting from the maximum adsorption capacities of 7.52 and 6.11 mg g-1. The just one magnetic extraction matrix based speciation scheme possesses excellent convenience and friendliness to Cr(VI) and Cr(III) without any oxidation or reduction prior to capture of these two species. This protocol has been successfully applied to the speciation analysis of inorganic chromium in real-world environmental water samples.

[Preparation of magnetic carbon nitride composite toward phosphopeptide enrichment].

Protein phosphorylation plays an important role in cellular signaling and disease development. Advances in mass spectrometry-based proteomics have enabled qualitative and quantitative phosphorylation studies as well as in-depth biological explorations for biomarker discovery and signaling pathway analysis. However, the dynamic changes that occur during phosphorylation and the low abundance of target analytes render direct analysis difficult because mass spectral detection offers no selectivity, unlike immunoassays such as Western blot and enzyme-linked immunosorbent assay (ELISA). The present study aimed to solve one of the key problems in the specific and efficient isolation of phosphorylated peptides. A method based on a magnetic carbon nitride composite coupled with matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS) was developed for the enrichment and analysis of phosphopeptides with low abundance in complex samples. Magnetic carbon nitride composite was synthesized and characterized by electron microscopy, infrared spectroscopy, and X-ray diffractometry. The composite showed a well-distributed two-dimensional layered structure and functional groups with excellent paramagnetic performance. Two classical phosphoproteins, namely, α- and ß-caseins, were selected as model phosphorylated samples to assess the performance of the proposed enrichment technique. The magnetic carbon nitride composite exhibited high selectivity and sensitivity for phosphopeptide enrichment. The limit of detection was determined by MALDI-TOF-MS analysis to be 0.1 fmol. The selectivity of the method was investigated using the digest mixtures of α-casein, ß-casein, and bovine serum albumin (BSA) with different mass ratios (1∶1∶1000, 1∶1∶2000, and 1∶1∶5000). Direct analysis of the samples revealed the dominance of spectral signals from the abundant peptides in BSA. After enrichment with the magnetic carbon nitride composite, the high concentration of background proteins was washed away and only the signals of the phosphopeptides were captured. The signals from the casein proteins were clearly observed with little background noise, indicating the high selectivity of the composite material. The robustness of the method was tested by assessing the reusability of the same batch of magnetic carbon nitride materials over 20 cycles of enrichment. The composite showed nearly the same enrichment ability even after several cycles of reuse, demonstrating its potential applicability for a large number of clinical samples. Finally, the method was applied to the analysis of phosphopeptides from several commonly used phosphoprotein-containing samples, including skimmed milk digest, human serum, and human saliva; these samples are significant in the analysis of food quality, disease biomarkers, and liquid biopsies for cancer. Without enrichment, no phosphopeptide was detected because of the high abundance of nonphosphopeptide materials dominating the spectral signals obtained. After pretreatment with the developed magnetic carbon nitride composite, most of the phosphosites were identified with high selectivity and sensitivity via MALDI-TOF-MS. These results revealed the practicality of the developed approach for clinical applications. In addition, our method may potentially be employed for phosphoproteomics with real complex biological samples.

Hollow multi-shelled MOF derivative adsorbent for efficient magnetic solid-phase extraction of several typical endocrine disrupting compounds from water.

Bisphenols and benzophenones are two typical kinds of endocrine-disrupting compounds (EDCs) that have been extensively detected in water environments, posing unanticipated risks to aquatic organisms and humans. It is urgent to develop efficient sample pretreatment methods for precise measurement of such EDCs. In this study, a magnetic and multi-shelled metal-organic framework derivative material has been prepared to extract and enrich trace bisphenols and benzophenones from water. Via a solvothermal reaction induced by sodium citrate followed by a carbonization treatment, a ZIF-67@ZIF-8 derived CoZn-magnetic hierarchical carbon (CoZn-MHC) material has been synthesized as a high-performance magnetic solid-phase extraction (MSPE) adsorbent. This adsorbent exhibited a good specific surface area (213.80 m2⋅g-1) and a saturation magnetization of 63.2 emu·g-1. After the optimization of several parameters (including adsorbent dosage, extraction time, pH, ionic strength, desorption solvent, and solvent volume), an efficient MSPE method for several EDCs (comprising bisphenols and benzophenones) was developed with a good linear range (R2 ≥ 0.990), a high sensitivity range (LODs: 0.793-5.37 ng⋅L-1), and good reusability (RSD ≤4.67 % in five consecutive tests). Furthermore, the material exhibited commendable resistance to matrix interference in natural water samples with the recovery rates of target compounds ranging from 74.8 % to 107 %. We envision that the preparation strategy of this functional metal-organic framework (MOF)-based adsorbent for EDCs may provide insights for relevant research in the future.

Effective enrichment and separation of three flavonoids from Ohwia caudata (Thunberg) H. Ohashi using magnetic layered double hydroxide/ZIF-8 composites and pCEC.

In this study, Fe3O4@ZnCr-layered double hydroxide/zeolitic imidazolate frameworks-8 (MLDH/ZIF-8) magnetically functionalized composites were synthesized by co-precipitation and in situ growth based on the advantages of LDHs and ZIF-8 using Fe3O4 nanoparticles as a magnetic substrate to obtain adsorbents with excellent performance. Moreover, the composite was used for the efficient enrichment of flavonoids in Chinese herbal medicines. The internal structures and surface properties were characterized by SEM, Fourier transform infrared spectroscopy, X-ray diffraction and so on. MLDH/ZIF-8 exhibited a large specific surface area and good paramagnetic properties. The MLDH/ZIF-8 magnetic composite was used as a magnetic solid-phase extraction (MSPE) adsorbent, and a MLDH/ZIF-8 MSPE-pressurized capillary electrochromatography coupling method was developed for the separation and detection of flavonoids (luteolin, kaempferol and apigenin) in a sample of the Chinese herb Ohwia caudata (Thunberg) H. Ohashi. The relevant parameters affecting the extraction efficiency were optimized to determine the ideal conditions for MSPE. 5 mg of adsorbent in sample solution at pH 6, vortex extraction for 5 min, elution with 1.5 mL of ethyl acetate for 15 min. The method showed good linearity in the concentration range of 3-50 µg mL-1 with correlation coefficients of 0.9934-0.9981, and displayed a relatively LODs of 0.07-0.09 µg mL-1. The spiked recoveries of all analytes ranged from 84.5% to 122.0% with RSDs (n=3) between 4.5% and 7.7%. This method is straightforward and efficient, with promising potential in the separation and analysis of active ingredients in various Chinese herbal medicines.

Synthesis of weak cation exchange/C18 bifunctional magnetic polymers for pretreatment and determination of glufosinate and its two metabolites in plasma samples.

This study focuses on the purification and detection of glufosinate (GLUF) and its metabolites N-acetyl GLUF and MPP in plasma samples. A Dikma Polyamino HILIC column was used for the effective retention and separation of GLUF and its metabolites, and the innovative addition of a low concentration of ammonium fluoride solution to the mobile phase effectively improved the detection sensitivity of the target analytes. Monodisperse core-shell weak cation exchange (WCX)/C18 bifunctional magnetic polymer composites (Fe3O4@WCX/C18) were prepared in a controllable manner, and their morphology and composition were fully characterized. The Fe3O4@WCX/C18 microspheres were used as a magnetic solid-phase extraction (MSPE) adsorbent for the sample purification and detection of GLUF and its metabolites in plasma samples combined with liquid chromatography-tandem mass spectrometry (LC-MS/MS). The purification conditions of Fe3O4@WCX/C18 microspheres for GLUF and its metabolites in spiked plasma samples were optimized to achieve the best MSPE efficiency. The purification mechanisms of the target analytes in plasma samples include electrostatic attraction and hydrophobic interactions. Furthermore, the effect of the molar ratio of the two functional monomers 4-VBA and 1-octadecene in the adsorbent was optimized and it shows that the bifunctional components WCX/C18 have a synergistic effect on the determination of GLUF and its metabolites in plasma samples. In addition, the present study compared the purification performance of the Fe3O4@WCX/C18 microsphere-based MSPE method with that of the commercial Oasis WCX SPE method, and the results showed that the Fe3O4@WCX/C18 microsphere-based MSPE method established in this work had a stronger ability to remove matrix interferences. Under optimal purification conditions, the recoveries of GLUF and its metabolites in plasma were 87.6-111 % with relative standard deviations (RSDs) ranging from 0.2 % to 4.8 %. The limits of detection (LODs, S/N≥3) and limits of quantification (LOQs, S/N≥10) were 0.10-0.18 µg/L and 0.30-0.54 µg/L, respectively. The MSPE-LC-MS/MS method developed in this study is fast, simple, accurate and sensitive and can be used to confirm GLUF intoxication based not only on the detection of the GLUF prototype but also on the detection of its two metabolites.

Magnetic solid-phase extraction-based surface-enhanced Raman spectroscopy for label-free therapeutic drug monitoring of carbamazepine and clozapine in human serum.

Determination of antiepileptic drugs and antipsychotics in human serum is significant in individualized drug administration and therapeutic drug monitoring (TDM). In this study, we developed a rapid label-free TDM method for the antiepileptic drug carbamazepine (CBZ) and the antipsychotic clozapine (CLO) in human serum. This detection strategy is based on the combination of surface-enhanced Raman scattering (SERS) and magnetic solid-phase extraction (MSPE). Initially, Fe3O4@SiO2@MIL-101(Fe) nanocomposites were synthesized by the layer-by-layer self-assembly method and characterized using scanning electron microscopy, transmission electron microscopy, X-ray diffraction, Brunauer-Emmett-Teller, ultraviolet-visible, and Fourier transform infrared analyses. Subsequently, CBZ and CLO were detected in human serum using Fe3O4@SiO2@MIL-101(Fe) as the solid-phase extraction adsorbent and Ag nanoparticles as SERS substrates. The potential of the MSPE-SERS method for the label-free TDM of CBZ and CLO was then investigated. Fe3O4@SiO2@MIL-101(Fe) prevents magnetic particle aggregation and demonstrates rapid magnetic separation capability that simplifies the pretreatment process and reduces interference from complex matrices. Its large surface area can effectively enrich targets in complex matrices, thereby improving the SERS detection sensitivity. The linearity between CBZ and CLO was excellent over the concentration range of 0.1-100 µg/mL (calculated as the intensity of the SERS characteristic peaks of CBZ and CLO at 728 cm and 1054 cm-1, respectively), with correlation coefficients (R2) of 0.9987 and 0.9957, and detection limits of 0.072 and 0.12 µg/mL, respectively. The recoveries of CBZ with CLO ranged from 94.0 % to 105.0 %, and their relative standard deviations were <6.8 %. Compared to other assays, the developed MSPE-SERS method has the advantages of simple sample pretreatment, rapid detection, and good reproducibility, which provides a novel approach for the TDM of other drugs.

Investigating the effect of type of fish and different cooking methods on the residual amount of polycyclic aromatic hydrocarbons (PAHs) in some Iranian fish: A health risk assessment.

The aim of this study was to assess the level of PAHs and associated health risks in different types of fish cooked with different methods, using the MSPE-GC/MS technique (magnetic solid phase extraction with gas chromatography/mass spectrometry). The limits of detection (LODs), limits of quantification (LOQs) and recovery percentages ranged from 0.1 to 0.63 µg/kg, 0.3-1.89 µg/kg, and 93.7 to 102.6%, respectively. The results showed that the mean of Æ©PAHs in all samples was 20.31 ± 6.60 µg/kg. Additionally, PAH4 and BaP levels in all samples were 4.58 ± 1.40 and 1.08 ± 0.36 µg/kg, respectively, which were below the European Union (EU) standard level (12 and 2 µg/kg, respectively). The results showed that among 5 types of fish, starry sturgeon had highest average total PAHs (13.24 ± 1.84 µg/kg), while Caspian Sea sprat had the lowest average total PAHs (1.24 ± 0.8 µg/kg). In terms of cooking methods (charcoal-grilled fish, fried fish and oven-grilled fish), charcoal-grilled fish had the highest average total PAH level at 25.41 ± 7.31 µg/kg, while the lowest average total PAH was found in the raw fish sample at 16.44 ± 4.63 µg/kg. The Monte Carlo Simulation was used to determine the 95% ILCRs (Incremental Lifetime Cancer Risk) due to ingestion of fish. The results showed that the ILCR for adults was 2.85E-9, while for children it was 1.32E-8. Therefore, based on these findings, it can be concluded that the consumption of fish cooked with different methods does not pose a risk to human health in terms of the amount of PAHs (ILCR < 1 × 10-4).

[Sulfonated magnetic graphite carbon nitride solid-phase extraction-ultra performance liquid chromatography-tandem mass spectrometry for screening malachite green and leucomalachite green in freshwater fish].

Malachite green (MG) and its metabolite, leucomalachite green (LMG), exert toxic effects on the human body. The use of these dyes is illegal, but they are still detected in aquatic products. Freshwater fish are aquatic products with the high non-qualified rates. Therefore, the sensitive screening of MG and LMG in freshwater fish is of great importance to ensure the safety of aquatic products. Owing to the low contents of MG and LMG in fish and the complex matrix of actual samples, sample preparation is required before detection to purify impurities and enrich the target compounds. Graphite carbon nitride (GCN), a polymer material composed of C, N, and H, has good chemical and thermal stability, a large specific surface area, and a large number of active sites. It has a wide range of application prospects in adsorption and can be used in food safety testing when compounded with Fe3O4 to form magnetic graphite carbon nitride (MGCN). In this study, sulfonated magnetic graphite carbon nitride (S-MGCN) was prepared by further functionalizing MGCN with sulfonic acid. After characterization by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), and vibrating sample magnetometry (VSM), a magnetic solid-phase extraction (MSPE) method based on S-MGCN was established to extract MG and LMG from freshwater fish. The targets were screened using ultra performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). Following sulfonic acid functionalization, S-MGCN showed increased electrostatic interactions based on the MGCN adsorption mechanism, which includes hydrogen bonds and π-π interactions; thus, its adsorption efficiency was significantly improved. The matrix effects were -42.21% and -33.77% before functionalization, -11.40% and -7.84% after functionalization, thus confirming that S-MGCN has significant matrix removal ability. Given that S-MGCN demonstrated excellent efficiency as an MSPE adsorbent, the adsorption conditions for S-MGCN were optimized. The optimal conditions were as follows: adsorbent dosage, 15 mg; adsorption time, 2 min; solution pH, 5; and ionic strength, not adjusted. Under these conditions, the adsorption efficiency of S-MGCN could reach 94.2%. Different organic solvents were used to elute adsorbed MG and LMG, and the desorption efficiency peaked when 1%(v/v) ammonia acetonitrile was used as the elution solvent. The elution volume was also optimized, and a maximum desorption efficiency of 93.2% was obtained when 1 mL of 1%(v/v) ammonia acetonitrile was added to S-MGCN. The limits of detection (LODs) and quantification (LOQs) of the two targets were determined at signal-to-noise ratios (S/N) of 3 and 10, respectively. The LODs and LOQs were 0.075 µg/kg and 0.25 µg/kg, respectively. The linear ranges of the two target compounds were 0.25-20.0 µg/kg with correlation coefficients (r) greater than 0.998. To assess accuracy and precision, we prepared spiked samples at three levels (low, medium, and high) with six parallel samples per level (n=6). The recoveries ranged from 88.8% to 105.9%. The intra- and inter-day relative standard deviations were 5.4%-13.7% (n=6) and 3.3%-11.1% (n=3), respectively. Compared with the national standard method, the proposed method features simpler sample pretreatment procedures, less use of organic reagents (5 mL), and a shorter extraction time (2 min); moreover, the method does not require complicated elution steps, and the eluent can be directly analyzed by UPLC-MS/MS. The test results of actual samples were consistent with those obtained via the national standard method, thus confirming the practical feasibility of the developed method. The proposed MSPE method based on S-MGCN is an efficient and environmentally friendly method that could provide a new methodological reference for the sensitive screening of MG and LMG in actual samples.

[Determination of four fungicides in water by magnetic solid phase extraction-ultrahigh performance liquid chromatography-tandem mass spectrometry using covalent organic framework material].

Fungicides can lead to soil and plant diseases after long-term enrichment in the environment; they can also penetrate deeper into the soil and groundwater by rainwater or irrigation, threatening the water environment and human health. Therefore, it is crucial to develop a simple, rapid, efficient, and sensitive analytical method for the detection of fungicides in the water environment. Sample pretreatment is important for the extraction and enrichment of pollutants from environmental water. Magnetic solid phase extraction (MSPE) is a new sample pretreatment method, which uses magnetic materials as adsorbents dispersed in solution, and rapid separation can be achieved by the aid of external magnets. Because of its advantages of short analytical time, less organic solvent consumption, and easy separation of adsorbents, MSPE has attracted much attention. The key to MSPE is the preparation of highly selective magnetic adsorbents. Covalent organic frameworks have the advantages of large surface area, good chemical and thermal stability, tunable porous structure, low density, and easy functionalization, all of which are ideal for adsorbing fungicides. The concentration of fungicides in environmental water is low. Ultrahigh performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) has high sensitivity and high selectivity, which is suitable for the analysis of fungicides. In this work, a magnetic covalent organic framework Fe3O4@TpBD was prepared by an in situ method, as the MSPE sorbent material to enrich of benzimidazole fungicides (thiabendazole, carbendazim, fuberidazole) and organic sulfur fungicide (isoprothiolane) in environmental water. An extraction method based on π-π conjugation, hydrogen bonding, and electrostatic interaction between Fe3O4@TpBD and the fungicides, in combination with UHPLC-MS/MS, was developed for the determination of four trace fungicides in water. Transmission electron microscopy (TEM), X-ray diffractometry (XRD), and Fourier transform-infrared spectroscopy (FT-IR) were performed to confirm the successful synthesis of Fe3O4@TpBD and to characterize this material. A series of experiments were carried out to decide the optimal extraction conditions, i. e., the magnetic ratio and dosage of Fe3O4@TpBD, pH of the water sample, adsorption time, type and volume of the eluent, elution time, and salinity. Gradient elution was carried out with methanol-water as the mobile phase. The target analytes were separated on an ACQUITY UPLC BEH C18 column (100 mm×2.1 mm, 1.7 µm), and multiple reaction monitoring (MRM) was conducted in the positive electrospray ionization mode. The ion source temperature and ion source voltage were set to 500 ℃ and 5 kV, respectively. The analytical method was established under the optimized extraction conditions. The four fungicides showed good linearity in the range of 3-1200 ng/L, with linear correlation coefficients greater than 0.998. The limits of detection (LODs) and limits of quantification (LOQs) of this developed method were 0.06-0.28 ng/L and 0.20-0.92 ng/L, respectively. Recovery tests were performed at three spiked levels of 15, 150, and 600 ng/L, with relative standard deviations of 2.8% to 10.0% (intra-day) and 4.4% to 15.7% (inter-day). The accuracy of the established analytical method was investigated by using it to test real water samples, and satisfactory recoveries for the four analytes were achieved within 77.1% to 119.1%. Trace amounts of carbendazim were detected in the reservoir water at 27.5 ng/L. The method has good sensitivity, accuracy, and precision, and the operation process is convenient.

[Analysis of parabens in environmental water samples by covalent organic framework-based magnetic solid-phase extraction-high performance liquid chromatography].

Parabens are a class of antimicrobial preservatives that are widely used in cosmetics, pharmaceuticals, and food products because of their ease of production, antimicrobial effect, and low price. The widespread use of these parabens, poses potential risks to human health. Therefore, it is necessary to establish a simple and rapid method for the detection of parabens. The large number of substrate interferences in complex samples is an important factor affecting the sensitivity of analytical methods. Magnetic solid-phase extraction (MSPE) has received much attention because of its advantages of easy operation, short extraction time, small sample amount, low cost, and environmental friendliness. Covalent organic frameworks (COFs) with high crystallinity, high specific surface area, adjustable pore size, regular porosity, as well as high chemical and thermal stability are now widely used in separation and analysis. Therefore, a sample pretreatment method combining MSPE and COF for the analysis of parabens in complex matrices is very promising. A magnetic covalent organic framework, Fe3O4@TbBd, was successfully synthesized by the Schiff base reaction of 1,3,5-triformylbenzene (Tb) and benzidine (Bd) at room temperature using Fe3O4 nanoparticles as magnetic cores. Characterization by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), X-ray diffraction (XRD), vibrating sample magnetometer (VSM) measurements, etc. revealed that the magnetic COF has high magnetic responsiveness, as well as good thermal and chemical stability, which make it an ideal adsorbent for the MSPE of parabens. Some factors related to the extraction efficiency, including the amount of adsorbent, extraction time, pH, desorption solvent, desorption time, and number of desorption were systematically investigated. A method involving MSPE and high performance liquid chromatography-ultraviolet detection (HPLC-UV) based on the Fe3O4@TbBd was developed for the determination of four parabens (ethylparaben, propylparaben, butylparaben, and benzylparaben) in environmental water samples. Under the optimal extraction conditions, the method showed good linearities. The limits of detection and limits of quantification were 0.2-0.4 µg/L and 0.7-1.4 µg/L for the four analytes, respectively. The recoveries at three spiked levels were in the range of 86.1%-110.8% with intra-day and inter-day RSDs of less than 5.5% and 4.9%, respectively. The method was successfully applied to the determination of parabens in East Lake water, Yangtze water, and domestic wastewater. Ethyl paraben and propyl paraben were detected in domestic wastewater at the levels of 1.8 µg/L and 0.4 µg/L, respectively. The recoveries of the parabens at different spiked levels ranged from 80.7% to 117.5%, with RSDs of 0.2%-8.8%. The method has good potential for the determination of parabens in environmental water samples because of its operational simplicity, short extraction time, high sensitivity, and environmental friendliness.

[Rapid Detection of Trace Enrofloxacin and Ciprofloxacin in Drinking Water by SERS].

In recent years, the abuse of antibiotics has led to the spread and diffusion of antibiotic resistance genes in the environment, which poses a potential threat to the ecosystem and human health. In particular, the related reports of antibiotic contamination in drinking water have aroused great social concerns. Therefore, realizing the rapid detection of trace antibiotics in emergency events has become a research hotspot. Here, in combination with magnetic solid phase extraction (MSPE), we established a rapid detection strategy for ng·L-1 level quinolones in drinking water using surface-enhanced Raman spectroscopy (SERS). With the help of the high enrichment capacity provided by the high adsorption capacity of the magnetic graphene oxide composite nanomaterial (Fe3O4@SiO2-GO), the spiked detection of 1.0 ng·L-1 enrofloxacin (ENR) and 5.0 ng·L-1 ciprofloxacin (CIP) in drinking water was successfully achieved, with recoveries ranging from 77.5% to 91.5%, which met the current requirements of drinking water testing. For environmental water samples such as lake water, the selectivity of extraction materials needs to be further improved due to the strong interference of the complex organic matrix.

["One-pot" preparation of aminated carbon nanotube-modified magnetic nanoparticles and their application to the quantification of phenoxyacetic acid herbicides in cereal and vegetable samples].

Phenoxyacetic acid herbicides (PAs) are widely used to control the growth of broad-leaf weeds in corn, tobacco, etc. The presence of PAs in plants even at low concentrations (at the ng/L to µg/L scale) may induce severe effects and lead to human health risks. Hence, a sensitive and reliable method for the determination of PAs at trace levels in cereals and vegetables is highly desired. Magnetic solid-phase extraction (MSPE) has attracted considerable attention on account of its benefits such as ease of separation, less solvent consumption, and good service life. In this study, aminated carbon nanotube-modified magnetic nanoparticles (NH2-CNTs@M) were prepared by a convenient and simple "one-pot" strategy and employed as the adsorbent for the MSPE of PAs in crops. The fabrication procedure is very convenient. In detail, the aminated carbon nanotubes, Fe(Ⅱ), Fe(Ⅲ), and isopropanol were mixed in one pot with mechanical stirring and reacted for 2.0 h at 80 ℃. The spectroscopic properties, morphology, and magnetic properties of the synthetic adsorbent were characterized by Fourier Transform-infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results revealed that the size of Fe3O4, diameter of NH2-CNTs, and the magnetic saturation values of NH2-CNTs@M were 30 nm, 40 nm, and 44.2 emu/g, respectively. Additionally, the results of FT-IR and TEM characterization confirmed the successful fabrication of NH2-CNTs@M by this "one-pot" hydrothermal approach. The NH2-CNTs@M displayed satisfactory capability to capture PAs through π-π, hydrophobic, and hydrogen-bonding interactions. To realize the best extraction performance, the key parameters, including the amount of adsorbent, formic acid concentration in the eluent, adsorption and desorption time, sample pH, and ionic strength in the sample matrices, were inspected and studied in detail. The optimal conditions were as follows: amount of NH2-CNTs@M, 30 mg; desorption solvent, 0.5 mL acetonitrile containing 2.0% (v/v) formic acid; adsorption and desorption times, 8.0 and 3.0 min, respectively; the sample pH was adjusted to 6.0, and no salt was added to the sample. Under the optimized extraction conditions, a sensitive, quick, and environmentally friendly method for the determination of the studied PAs in cereal and vegetable samples was established by the combination of NH2-CNTs@M/MSPE with high performance liquid chromatography-diode array detection (HPLC-DAD). The enrichment factors for the studied PAs varied from 73 to 90. The limits of detection (S/N=3) for the PAs in the cereal and vegetable matrixes were in the ranges of 0.32-1.6 µg/kg and 0.53-1.6 µg/kg, respectively; and the limits of quantification (S/N=10) for the PAs in the cereal and vegetable matrixes were 0.94-4.8 µg/kg and 1.6-4.8 µg/kg. The developed method also showed wide linear ranges and good precision. Finally, the established NH2-CNTs@M/MSPE-HPLC-DAD approach was applied to measure trace levels of PAs in cereals and vegetables, and good fortified recoveries (72.3% to 113%) and repeatability (RSDs below 10%) were obtained. The established approach has several advantages over the existing methods, such as high analytical speed, low LODs, and eco-friendliness.

In situ anchor of multi-walled carbon nanotubes into iron-based metal-organic frameworks for enhanced adsorption of polycyclic aromatic hydrocarbons by magnetic solid-phase extraction.

In this work, a magnetic MIL-101(γ-Fe2O3)/MWCNTs composite derived from iron-based metal-organic frameworks (MIL-101(Fe)) with multi-walled carbon nanotubes (MWCNTs) was successfully synthesized by low-temperature calcination process. The composite was used as adsorbent of magnetic solid-phase extraction (MSPE) for enhanced and rapid enrichment of trace polycyclic aromatic hydrocarbons (PAHs) based on its strong π-π stacking interactions, hydrophobic and cationic-π stacking interactions. The pseudo-second-order kinetic model and Langmuir isotherm model could be applied to better describe the adsorption process. The maximum adsorption capacity for PAHs reached 93.9 mg g-1. In addition, the conditions of MSPE process were optimized by orthogonal array design (OAD). A MSPE-HPLC-UV method was established for the sensitive detection of PAHs in real water samples and exhibited wide linear range (0.05-1000 µg L-1), low detection limits (0.02-0.41 µg L-1) and high enrichment factors (44-169) for PAHs. The relative standard deviations (RSD) ranged from 0.8 to 4.0% and 1.2-7.2% for single batch and batch-to-batch, respectively, and the spiked recoveries at two levels of 10 and 50 µg L-1 ranged from 79.6 to 112% with RSD of less than 5.81%. The unique MWCNTs in situ anchor MIL-101(γ-Fe2O3) composite with an outstanding PAHs adsorption performance provides a new opportunity and promising application in removal of toxic pollutants.

Fabrication of Magnetic Al-Based Fe3O4@MIL-53 Metal Organic Framework for Capture of Multi-Pollutants Residue in Milk Followed by HPLC-UV.

The efficient capture of multi-pollutant residues in food is vital for food safety monitoring. In this study, in-situ-fabricated magnetic MIL-53(Al) metal organic frameworks (MOFs), with good magnetic responsiveness, were synthesized and applied for the magnetic solid-phase extraction (MSPE) of chloramphenicol, bisphenol A, estradiol, and diethylstilbestrol. Terephthalic acid (H2BDC) organic ligands were pre-coupled on the surface of amino-Fe3O4 composites (H2BDC@Fe3O4). Fe3O4@MIL-53(Al) MOF was fabricated by in-situ hydrothermal polymerization of H2BDC, Al (NO3)3, and H2BDC@Fe3O4. This approach highly increased the stability of the material. The magnetic Fe3O4@MIL-53(Al) MOF-based MSPE was combined with high-performance liquid chromatography-photo diode array detection, to establish a novel sensitive method for analyzing multi-pollutant residues in milk. This method showed good linear correlations, in the range of 0.05-5.00 µg/mL, with good reproducibility. The limit of detection was 0.004-0.108 µg/mL. The presented method was verified using a milk sample, spiked with four pollutants, which enabled high-throughput detection and the accuracies of 88.17-107.58% confirmed its applicability, in real sample analysis.

A combination approach using two functionalized magnetic nanoparticles for speciation analysis of inorganic arsenic.

Mercapto- and amino-functionalized magnetic nanoparticles, Fe3O4@SiO2@MPTMS (SMNPs-MPTMS) and Fe3O4@SiO2@APTES (SMNPs-APTES), have been applied as magnetic solid-phase extraction (MSPE) sorbents to directly extract arsenite (As(III)) and arsenate (As(V)) respectively, followed by inductively coupled plasma-mass spectrometry (ICP-MS) detection. Various MSPE parameters were optimized including dose of magnetic adsorbent, pH of sample solution, loading and elution conditions of analytes, adsorption capacity and reusability of SMNPs-MPTMS and SMNPs-APTES for As(III) and As(V) respectively. Under the optimized MSPE conditions, this combined scheme possesses excellent selectivity and strong anti-interference ability without any oxidation or reduction prior to capture of these two species. It is found that with a 25-fold enrichment factor, the limits of detection of As(III) and As(V) were 23.5 and 10.5 ng L-1, respectively. To verify the reliability of the proposed protocol, a certified reference material of environmental water was analyzed, and the results for inorganic arsenic species were in close agreement with the certified values. The applicability of the combination strategy for speciation analysis of inorganic arsenic was evaluated in spiked tap, river, lake and rain water samples. Good recoveries of 89%-96% and 90%-102% were achieved for As(III) and As(V), respectively, with the relative standard deviation ranges of 3.2%-8.0% and 2.5%-7.6%. Through the characterization of functionalized magnetic nanoparticles and the optimization of MSPE experiment, it is confirmed that the existence of mercapto and amino groups on SMNPs-MPTMS and SMNPs-APTES sorbents are responsible for the extraction of As(III) and As(V), respectively, via coordination and electrostatic interactions.

Nanoparticles Based Extraction Strategies for Accurate and Sensitive Determination of Different Pesticides.

Sample preparation methods have become indispensable steps in analytical measurements not only to lower the detection limit but also to eliminate the matrix effect although more sophisticated instruments are being commonly used in routine analyses. Solid phase extraction (SPE) is one of the main extraction/preconcentration methods used to extract and purify target analytes along with simple and rapid procedures but some limitations have led to seek for an easy, sensitive and fast extraction methods with analyte-selective sorbents. Nanoparticles with different modifications have been used as spotlight to enhance extraction efficiency of target pesticides from complicated matrices. Carbon-based, metal and metal oxides, silica and polymer-based nanoparticles have been explored as promising sorbents for pesticide extraction. In this review, different types of nanoparticles used in the preconcentration of pesticides in various samples are outlined and examined. Latest studies in the literature are discussed in terms of their instrumental detection, sample matrix and limit of detection values. Novel strategies and future directions of nanoparticles used in the extraction and preconcentration of pesticides are also discussed.

[Advances in solid-phase extraction for bisphenols in environmental samples].

Owing to the strict restrictions on the production and use of bisphenol A (BPA), bisphenol analogs (e. g., bisphenol S and bisphenol F) are gradually coming to use in many fields. BPA and these bisphenol analogs are so-called bisphenols (BPs). BPs as a class of endocrine disrupters are widely distributed in the environment (water, sediments, sludge, and aquatic products). BPs enter the human body through various routes, leading to endocrine disruption, cytotoxicity, genotoxicity, reproductive toxicity, dioxin-like effects, and neurotoxicity. The Canadian government has identified BPs as substances for further scoping/problem formulation. Because of the widespread attention paid to BPs in the environmental field, research is being expanded to cover water, sediment, dust, and biological samples, and other media. Given the significant differences in the complexity and pollution concentration of environmental samples, the development of pretreatment methods that afford high extraction efficiency, good purification selectivity, strong universality, operational simplicity, and high-throughput extraction and purification, are necessary to realize the highly sensitive detection of BPs in environmental media. In recent years, solid-phase extraction (SPE), accelerated solvent extraction (ASE), microwave-assisted extraction (MAE), and dispersion liquid-liquid-microextraction (DLLME) as new pretreatment technologies have gradually replaced the traditional liquid-liquid extraction and Soxhlet extraction. SPE has seen rapid development for the extraction and purification of BPs in various environmental samples, overcoming the bottlenecks related to time, energy, and solvent consumption in traditional methods while extending technical support for the analysis of emerging pollutants. The physicochemical properties, usage, and environmental hazards of typical BPs were briefly reviewed, with emphasis on the application of SPE products, development of new adsorbents, and transformation of the SPE mode. Commercialized SPE products are universally applicable in the field of environmental monitoring, while products suitable for the pretreatment of BPs are limited. The development of new adsorbents mainly focused on their adsorption capacity and selectivity. For example, ordered mesoporous silicon, carbon nanomaterials, metal-organic frameworks, and cyclodextrins have large surface areas, good adsorption performance, and regular pore structures, which improve the adsorption capacity of BPs. Molecularly imprinted polymers (MIPs) and mixed-mode ion-exchange polymers are mainly used to improve the selectivity of BPs in the purification process. In addition, MIPs have high chemical, mechanical, and thermal stabilities, which ensures their widespread application in the extraction, preconcentration, and separation of BPs. A variety of new SPE adsorbents can partially meet the diverse needs for detection. There is a consensus that the current challenges in analytical chemistry include the determination of contaminants at low concentration levels, but at the same time, more efficient and environment-friendly methodologies are required. With the introduction of high-sensitivity instruments in the market, the SPE model is seeing gradual development in terms of miniaturization, automation, and simplification. This in turn has minimized solvent consumption, analysis time, and labor cost, resulting in more efficient and affordable analytical methods such as QuEChERS, solid-phase microextraction (SPME), and magnetic solid-phase extraction (MSPE) to adapt to the new development scenario.

[Determination of three diphenyl ether herbicides in rice by magnetic solid phase extraction using Fe3O4@MOF-808 coupled with high performance liquid chromatography].

The complex matrix of rice samples and the small amount of the target analytes in the sample necessitate an effective pretreatment process to enrich the target analytes and minimize matrix interference before instrumental analysis. Magnetic solid phase extraction (MSPE) is a dispersive solid phase extraction technique which allows for the rapid separation of sorbents from the sample solution under an external magnetic field. Compared with other traditional solid phase extraction methods, MSPE has the advantages of convenient operation, minimal interference and absence of column pressure. In this work, a metal organic framework composite (Fe3O4@MOF-808) was synthesized by a facile solvothermal method for using as an effective adsorbent to concentrate nitrofen (NIT), oxyfluorfen (OXY) and bifenox (BIF) in rice samples. Based on the pretreatment, a method was developed by coupling with high performance liquid chromatography-ultraviolet detection (HPLC-UV). The prepared material was characterized by Fourier-transform infrared spectroscopy, X-ray diffractometry, scanning electron microscopy and vibrating sample magnetometry measurements for determining its functional groups, morphology and magnetic strength. The results showed that MOF-808 has a regular octahedral morphology and well-dispersed, and the particle size of the material ranged from 400 to 500 nm with a smooth surface. The spherical Fe3O4 particles were uniformly attached to the surface of the octahedral MOF-808 crystals. The maximum saturation magnetization of this composite was 40.35 emu/g which is lower than the saturation magnetization Fe3O4 (78.26 emu/g) but still sufficient for the requirements of MSPE. The prepared Fe3O4@MOF-808 was used in the MSPE of three diphenyl ether herbicides (Des) in rice. As is well known, the key factors influencing MSPE are the adsorption and elution processes. In order to establish the optimal extraction conditions, the adsorption parameters (adsorbent amount, extraction time, elution solvent and elution volume) were investigated in detail. A 15 mL mixed standard solution was used in the experiment, and the concentrations of the three Des were 65 ng/mL. All the experiments were performed in parallel three times. The effects of the dosages of Fe3O4@MOF-808 (10, 15, 20, 25 and 30 mg), adsorption time (2, 4, 6, 8 and 10 min), elution solvents (acetone, acetonitrile and methanol) and elution volume (0.5 mL, 0.5 mL×2, 0.5 mL×3, 0.5 mL×4) were investigated. The Des could be adsorbed completely by using 25 mg of Fe3O4@MOF-808 for no more than 6 min. Elution was performed with 0.5 mL×2 of methanol. Various parameters such as limits of detection (LODs), limits of quantification (LOQs), accuracy and precision of the method were evaluated. The method showed good linearity in the range of 2-300 µg/L (r > 0.998). The LODs and LOQs were 0.6, 0.6, 0.4 µg/kg and 2.0, 2.0,1.5 µg/kg for NIT, OXY, BIF respectively. At spiked levels of 5, 10 and 20 µg/kg, the recoveries ranged from 87.3% to 96.7% with relative standard deviations (RSDs) less than 10.8%. The enrichment factors (EFs) of the method for the three Des were between 25 and 29. The method was applied to the pretreatment of the three Des in real samples, and none of the Des could be detected at any of the samples. This method had a lower LOD than that of the national standard method, but its LOD and recovery were similar to those of other reference methods. In summary, the developed method has the advantages of operational simplicity, rapidity and accuracy, and it is suitable for the analysis of herbicide residues in rice samples.