New powder reuse schema in laser-based powder bed fusion of polymers.

The laser-based powder bed fusion of polymers (PBF-LB/P) process often utilizes a blend of powders with varying degrees of degradation. Specifically, for polyamide 12, the traditional reuse schema involves mixing post-processed powder with virgin powder at a predetermined ratio before reintroducing it to the process. Given that only about 15% of the powder is utilized in part production, and powders are refreshed in equal proportions, there arises a challenge with the incremental accumulation of material across build cycles. To mitigate the consumption of fresh powder relative to the actual material usage, this study introduces the incorporation of recycled material into the PBF-LB/P process. This new powder reuse schema is presented for the first time, focusing on the laser sintering process. The characteristics of the recycled powder were evaluated through scanning electron microscopy, differential scanning calorimetry, X-ray diffraction, particle size distribution, and dynamic powder flowability assessments. The findings reveal that waste powders can be effectively reused in PBF-LB/P to produce components with satisfactory mechanical properties, porosity levels, dimensional accuracy, and surface quality.

Topological Polymer Networks-Enabled Mechanically Strong Polyamide-Imide Aerogel Fibers for Thermal Insulation in Harsh Environments.

Aerogel fibers have sparked substantial interest as attractive candidates for thermal insulation materials. Developing aerogel fibers with the desired porous structure, good knittability, flame retardancy, and high- and low-temperature resistance is of great significance for practical applications; however, that is very challenging, especially by using an efficient method. Herein, mechanically strong and flexible aerogel fibers with remarkable thermal insulation performance are reported, which are achieved by constructing stiff-soft topological polymer networks and a multilevel hollow porous structure. The combination of polyamide-imide (PAI) with stiff chains and polyurethane (PU) with soft chains is first found to be able to form a topological entanglement architecture. More importantly, multilevel hollow pores can be constructed synchronously through just a one-step and green wet-spinning process. The resultant PAI/PU@340 aerogel fibers show an ultrahigh breaking strength of 94.5 MPa and superelastic property with a breaking strain of 20%. Furthermore, they can be knitted into fabrics with a low thermal conductivity of 25 mW/(m·K) and exhibit attractive thermal insulation property under extremely high (300 °C) and low temperatures (-191 °C), implying them as promising candidates for next-generation thermal insulation materials.

Effect of beverages, denture cleanser and chlorhexidine gluconate on surface roughness of flexible denture base material: an in vitro study.

Purpose: The purpose of the study was to evaluate and compare the effect of beverages, denture cleanser and chlorhexidine gluconate solution on surface roughness of flexible denture base material. Materials and methods: Fifty flexible denture base resin specimens measuring 50±1mm in diameter and 0.5±0.05 mm in thickness were fabricated. The specimens were divided into five groups each containing ten specimens. The specimens were immersed in distilled water (Control group A); hot coffee (Group B); cold beverage (Group C); sodium perborate containing denture cleanser (Group D) and 2% chlorhexidine gluconate solution (Group E). The specimens were immersed for 10 min daily in mentioned solutions for up to 60 days. Surface roughness (Ra) was evaluated on the 1st, 20th and 60th day with the help of atomic force microscope. The statistical analysis was done using two-way ANOVA and Tukey's Post hoc test. Results: The two- way ANOVA revealed that the average Ra values varied significantly depending on the type of solution used for immersion (p<0.001) and the duration of immersion (p<0.001). Variation in surface roughness with cold beverage was highest (p=0.001). On the 60th day the surface roughness of flexible denture base resin material was higher with cold beverage (0.184 µm) and denture cleanser (0.203 µm) than that of distilled water (0.052 µm) hot coffee (0.030 µm) and 2% chlorhexidine gluconate (0.068 µm). Conclusion: Exposure to cold beverage, which was acidic in nature and peroxide containing denture cleanser, produces much rougher surface in the thermoplastic polyamide flexible denture base resin specimens.

3-Pentadecylphenol (PDP) as a Novel Compatibilizer for Simultaneous Toughened and Reinforced PA10,12 Composites.

The utilization of polyamide 10,12 (PA10,12) composites in various industries has been limited constrained by their inherent low toughness, making it a challenge to achieve a balance between toughness and structural integrity through conventional elastomer addition strategies. Herein, we introduce a straightforward method for the concurrent toughening and reinforcement of PA10,12 composites. This is accomplished by blending polyolefin elastomer (POE) and 3-pentadecylphenol (PDP) with the PA10,12 matrix. The incorporation of 5 wt% PDP effectively blurred the PA10,12/POE interface due to PDP's role as a compatibilizer. This phenomenon is attributed to the formation of intermolecular hydrogen bonds, as evidenced by Fourier Transform Infrared Spectroscopy (FTIR) analysis. Further investigation, using differential scanning calorimetry (DSC), elucidated the crystallization thermodynamics and kinetics of the resulting binary PA10,12/POE and ternary PA10,12/POE/PDP composites. Notably, the crystallization temperature (Tc) was observed to decrease from 163.1 °C in the binary composite to 161.5 °C upon the addition of PDP. Increasing the PDP content to 10% led to a further reduction in Tc to 159.5 °C due to PDP's capacity to slow down crystallization. Consequently, the ternary composite of PA10,12/POE/PDP (92/3/5 wt%) demonstrated a synergistic improvement in mechanical properties, with an elongation at break of 579% and a notch impact strength of 61.54 kJ/m2. This represents an approximately eightfold increase over the impact strength of unmodified PA10,12. Therefore, our work provides the potential of PDP as a compatibilizer to develop nylon composites with enhanced stiffness and toughness.

The Recyclability of Fire-Retarded Biobased Polyamide 11 (PA11) Composites Reinforced with Basalt Fibers (BFs): The Influence of Reprocessing on Structure, Properties, and Fire Behavior.

The growing requirements regarding the safety of using polymers and their composites are related to the emergence of more effective, sustainable, and hazardous-limited fire retardants (FRs). Significant amounts of FRs are usually required to effectively affect a polymer's burning behavior, while the knowledge of their recycling potential is still insufficient. At the same time, concerns are related not only to the reduced effectiveness of flame retardancy but also, above all, to the potential deterioration of mechanical properties caused by the degradation of temperature-affected additives under processing conditions. This study describes the impact of the four-time reprocessing of bio-based polyamide 11 (PA11) modified with an intumescent flame-retardant (IFR) system composed of ammonium polyphosphate (APP), melamine cyanurate (MC), and pentaerythritol (PER) and its composites containing additional short basalt fibers (BFs). Composites manufactured via twin-screw extrusion were subjected to four reprocessing cycles using injection molding. A comprehensive analysis of their structural, mechanical, and fire behavior changes in each cycle was conducted. The obtained results confirmed the safety of using the proposed fire-retarded polyamide and its composites while reprocessing under the recommended process parameters without the risk of significant changes in the structure. The partial increase in flammability of reprocessed PA-based materials caused mainly by polymer degradation has been described.

Metagenome-derived SusD-homologs affiliated with Bacteroidota bind to synthetic polymers.

Starch utilization system (Sus)D-homologs are well known for their carbohydrate-binding capabilities and are part of the sus operon in microorganisms affiliated with the phylum Bacteroidota. Until now, SusD-like proteins have been characterized regarding their affinity toward natural polymers. In this study, three metagenomic SusD homologs (designated SusD1, SusD38489, and SusD70111) were identified and tested with respect to binding to natural and non-natural polymers. SusD1 and SusD38489 are cellulose-binding modules, while SusD70111 preferentially binds chitin. Employing translational fusion proteins with superfolder GFP (sfGFP), pull-down assays, and surface plasmon resonance (SPR) has provided evidence for binding to polyethylene terephthalate (PET) and other synthetic polymers. Structural analysis suggested that a Trp triad might be involved in protein adsorption. Mutation of these residues to Ala resulted in an impaired adsorption to microcrystalline cellulose (MC), but not so to PET and other synthetic polymers. We believe that the characterized SusDs, alongside the methods and considerations presented in this work, will aid further research regarding bioremediation of plastics. IMPORTANCE: SusD1 and SusD38489 can be considered for further applications regarding their putative adsorption toward fossil-fuel based polymers. This is the first time that SusD homologs from the polysaccharide utilization loci (PUL), largely described for the phylum Bacteroidota, are characterized as synthetic polymer-binding proteins.

An Innovative Approach for Elemental Mercury Adsorption Using X-ray Irradiation and Electrospun Nylon/Chitosan Nanofibers.

A novel approach was proposed, utilizing an electrical field and X-ray irradiation to oxidize elemental mercury (Hg0) and encapsulate it within a nanofibrous mat made of Polyamide 6/Chitosan. The X-rays contributed significantly to the conversion of Hg0 into Hg+ by producing electrons through the photoionization of gas molecules. The positive and negative pole electrodes generated an electric field that exerted a magnetic force, resulting in the redirection of oxidized elemental mercury towards the negative pole electrode, which was coupled with a Polyamide 6/Chitosan nanofiber mat. The evaluation of the Polyamide 6/Chitosan nanofibers exposed to oxidized mercury showed that the mercury, found in the steam of a specially designed filtration device, was captured in two different forms. Firstly, it was chemically bonded with concentrations ranging from 0.2 to 10 ng of Hg in total. Secondly, it was retained on the surface of the Polyamide 6/Chitosan nanofibers with a concentration of 10 microg/m3 of Hg per minute. Nevertheless, a concentration of 10 microg/m3 of mercury is considered significant, given that the emission levels of mercury from each coal power plant typically vary from approximately 4.72 to 44.07 microg/m3. Thus, this research presents a viable approach to reducing mercury emissions from coal-fired power plants, which could result in lower operational expenses and less secondary environmental effects.

Investigation of Recycled Expanded Polyamide Beads through Artificial Ageing and Mechanical Recycling as a Proof of Concept for Circular Economy.

Car manufacturers are currently challenged with increasing the sustainability of their products and production to comply with sustainability requirements and legislation. One way to enhance product sustainability is by reducing the carbon footprint of fossil-based plastic parts. Particle foams are a promising solution to achieve the goal of using lightweight parts with minimal material input. Ongoing developments involve the use of expanded particle foam beads made from engineering plastics such as polyamide (EPA). To achieve this, a simulated life cycle was carried out on virgin EPA, including mechanical recycling. The virgin material was processed into specimens using a steam-free method. One series was artificially aged to replicate automotive life cycle stresses, while the other series was not. The mechanical recycling and re-foaming of the minipellets were then carried out, resulting in an EPA particle foam with 100% recycled content. Finally, the thermal and chemical material properties were comparatively analysed. The study shows that the recycled EPA beads underwent polymer degradation during the simulated life cycle, as evidenced by their material properties. For instance, the recycled beads showed a more heterogeneous molecular weight distribution (an increase in PDI from two to three), contained carbonyl groups, and exhibited an increase in the degree of crystallization from approximately 24% to 36%.

Hyperbranched polymeric membranes for industrial water purification.

This work aims at the preparation and characterization of dual-layer (DL) nano-fibrous mat (NFM) of hydrophobic and mechanical stable polyacrylonitrile (PAN) nano-fibers (NFs), as a supporter, and polyamide 6 (PA)/chitosan (Ch) NFs as a top hydrophilic coating layer. PAN and PA fibers, as residual wastes from textile processes, were collected and dissolved in their proper solvents. PAN was electro-spuned under certain conditions of electro-spinning (voltage, flow rate, and distance between spinneret and collector) to obtain PAN-NFM. Different ratios of PA/Ch composite were prepared and then electro-spun above the PAN-NFM that was previously prepared to obtain hydrophobic/hydrophilic functional dual-layer nano-fibrous membrane (DLNFM). The efficiency of the prepared DLNFM for capturing dye residues and heavy metals from wastewater was investigated. The viscosities of the prepared composite solutions were measured. The prepared dual-layer nano-fiber membranes (DLNFMs) were chemically and physically characterized by Fourier transform infrared spectroscopy, scanning electron microscope, X-ray diffraction, and thermogravimetric analyzer. The potential of the prepared mats for the adsorption of some heavy metal ions, i.e., Cu+2, Cr+3, and Pb+2 cations in addition to dyes from wastewater was evaluated. The effect of using different concentrations of PA/Ch composite as well as the thickness of the obtained DLNFM on the filtration efficiency was studied. The results of this study show the success of functional DLNFM in dye and heavy metal removal. The maximum removal efficiency of acid dyes was reached to 73.4 % and of reactive dye was approximately 61 % for PAN/PA-1.25%Ch DLNFM after 3 days at room temperature. The removal efficiency percent of heavy metal ions reached to 54 % by DLNFM. Additionally, the results showed that 0.08 mm is the ideal thickness for maximum absorption capacity. This value is correlated with the membrane's highest Ch percentage, which is (PAN/PA-1.25%Ch). Furthermore, the results demonstrate that the presence of the Ch polymer strengthened the produced bi-layered membrane to achieve the highest thermal stability when compared to the other nano-fibrous membranes (NFMs), with the breakdown temperature of the Ch functionalized dual-layer membranes (DLMs) reaching approximately 617 °C and a maximum weight loss of 60 %.

Polar Solvent-Induced Spontaneous Nanofoaming for Synthesizing Ultra-High-Performance Polyamide Nanofiltration Membranes.

Nanofiltration membranes with both high water permeance and selectivity are perpetually studied because of their applications in water purification. However, these two critical attributes are considered to be mutually exclusive. Here, we introduce a polar solvent, dichloromethane, in place of the apolar hexane used for decades as the organic phase for membrane interfacial polymerization synthesis to solve this dilemma. When a polar solvent as the organic phase is combined with a solvent-resistant aramid nanofibrous hydrogel film as the water phase, monomer enrichment in the reaction zone leads to a polyamide nanofiltration membrane with densely distributed nanobubble features, enhanced nanoporosity, and a loosened backbone. Benefiting from these structural features, the resulting membrane exhibits superior properties with a combination of high water permeance (52.7 L m-2 h-1 bar-1) and selectivity (water/Na2SO4, 36 bar-1; NaCl/Na2SO4, 357 bar-1), outperforming traditional nanofiltration membranes. We envision that this novel technology involving polar solvent systems and the water phase of nanofibrous hydrogel would provide new opportunities for membrane development for environmental engineering.

Modeling Ion Transport across Thin-Film Composite Membranes During Saltwater Electrolysis.

Affordable thin-film composite (TFC) membranes are a potential alternative to more expensive ion exchange membranes in saltwater electrolyzers used for hydrogen gas production. We used a solution-friction transport model to study how the induced potential gradient controls ion transport across the polyamide (PA) active layer and support layers of TFC membranes during electrolysis. The set of parameters was simplified by assigning the same size-related partition and friction coefficients for all salt ions through the membrane active layer. The model was fit to experimental ion transport data from saltwater electrolysis with 600 mM electrolytes at a current density of 10 mA cm-2. When the electrolyte concentration and current density were increased, the transport of major charge carriers was successfully predicted by the model. Ion transport calculated using the model only minimally changed when the negative active layer charge density was varied from 0 to 600 mM, indicating active layer charge was not largely responsible for controlling ion crossover during electrolysis. Based on model simulations, a sharp pH gradient was predicted to occur within the supporting layer of the membrane. These results can help guide membrane design and operation conditions in water electrolyzers using TFC membranes.

Waterless Dyeing of Polyamide 6.6.

Waterless dyeing of polyamide 6.6 using scCO2 (supercritical carbon dioxide) was investigated. PA (polyamide) fibers can be dyed with various dyes, including disperse dyes. The conventional aqueous dyeing process uses large amounts of water and produces polluted water. Considering these environmental issues, waterless dyeing of fibers is a forefront issue, and utilization of supercritical carbon dioxide (scCO2) is a commercially viable technology for waterless dyeing. This study tested PA6.6 (polyamide 6.6) dyeing in scCO2 at 100 °C 220 bar pressure for 45 min. Color measurements and color fastness tests were performed, as well as tensile strength, scanning electron microscope (SEM) analysis, and Fourier transform infrared spectroscopy (FTIR) analysis. PA6.6 fabrics yielded higher K/S (color strength, the Kubelka-Munk equation) values with larger molecular weight dye and almost the same color strength with medium and small-sized dyes, demonstrating the ability of dyeing in a supercritical environment without water as a more environmentally friendly dyeing option compared to conventional dyeing.

Parametric Optimization of FDM Process for PA12-CF Parts Using Integrated Response Surface Methodology, Grey Relational Analysis, and Grey Wolf Optimization.

Efficiently managing multiple process parameters is critical for achieving optimal performance in additive manufacturing. This study investigates the relationship between eight key parameters in fused deposition modeling (FDM) and their impact on responses like average surface roughness (Ra), tensile strength (TS), and flexural strength (FS) of carbon fiber-reinforced polyamide 12 (PA 12-CF) material. The study integrates response surface methodology (RSM), grey relational analysis (GRA), and grey wolf optimization (GWO) to achieve this goal. A total of 51 experiments were planned using a definitive screening design (DSD) based on response RSM. The printing process parameters, including layer thickness, infill density, and build orientation, significantly affect Ra, TS, and FS. GRA combines responses into a single measure, grey relational grade (GRG), and a regression model is developed. GWO is then employed to optimize GRG across parameters. Comparison with GRA-optimized parameters demonstrates GWO's ability to discover refined solutions, reducing average surface roughness to 4.63 µm and increasing tensile strength and flexural strength to 88.5 MPa and 103.12 MPa, respectively. Practical implications highlight the significance of GWO in industrial settings, where optimized parameters lead to reduced costs and improved product quality. This integrated approach offers a systematic methodology for optimizing FDM processes, ensuring robustness and efficiency in additive manufacturing applications.

Optimization of Electrospun TORLON® 4000 Polyamide-Imide (PAI) Nanofibers: Bridging the Gap to Industrial-Scale Production.

Polyamide-imide (PAI) is an exceptional polymer known for its outstanding mechanical, chemical, and thermal resistance. This makes it an ideal choice for applications that require excellent durability, such as those in the aerospace sector, bearings, gears, and the oil and gas industry. The current study explores the optimization of TORLON® 4000 T HV polyamide-imide nanofibers utilizing needleless electrospinning devices, ranging from laboratory-scale to industrial-scale production, for the first time. The PAI polymer has been dispersed in several solvent systems at varying concentrations. The diameter of the electrospun PAI nanofibers ranged from 65.8 nanometers to 1.52 µm. Their filtering efficiency was above 90% for particles with a size of 0.3 microns. The TGA results proved that PAI nanofibers have excellent resistance to high temperatures up to 450 °C. The PAI nanofibers are ideal for hot air intake filtration and fire-fighter personal protection equipment applications.

Unique Self-Phosphorylating Polybenzimidazole of the 6F Family for HT-PEM Fuel Cell Application.

High-temperature polymer-electrolyte membrane fuel cells (HT-PEMFCs) are a very important type of fuel cells since they operate at 150-200 °C, making it possible to use hydrogen contaminated with CO. However, the need to improve the stability and other properties of gas-diffusion electrodes still impedes their distribution. Self-supporting anodes based on carbon nanofibers (CNF) are prepared using the electrospinning method from a polyacrylonitrile solution containing zirconium salt, followed by pyrolysis. After the deposition of Pt nanoparticles on the CNF surface, the composite anodes are obtained. A new self-phosphorylating polybenzimidazole of the 6F family is applied to the Pt/CNF surface to improve the triple-phase boundary, gas transport, and proton conductivity of the anode. This polymer coating ensures a continuous interface between the anode and proton-conducting membrane. The polymer is investigated using CO2 adsorption, TGA, DTA, FTIR, GPC, and gas permeability measurements. The anodes are studied using SEM, HAADF STEM, and CV. The operation of the membrane-electrode assembly in the H2/air HT-PEMFC shows that the application of the new PBI of the 6F family with good gas permeability as a coating for the CNF anodes results in an enhancement of HT-PEMFC performance, reaching 500 mW/cm2 at 1.3 A/cm2 (at 180 °C), compared with the previously studied PBI-O-PhT-P polymer.

Structural Optimization of PA12/MVQ@POE-g-MAH Ternary Composite for Superior Toughness and Low-Temperature Resistance.

To enhance the low-temperature toughness and resistance of the engineering plastic polyamide PA12, this study introduces novel PA12/MVQ@POE-g-MAH ternary composites using a two-step process and dynamic curing. Analytical results indicate that incorporating MVQ@POE-g-MAH into the PA12 matrix markedly enhances its toughness and heat resistance. As the MVQ@POE-g-MAH content increases, the elongation at break of PA12 composites significantly expands from 52.83% to 204.69%, and the notch impact strength escalates from 8.69 to 74.34 kJ m-2. In addition, the brittleness temperature of PA12 decreases from -59.5 to -67.0 °C. Experimental findings confirm that POE-g-MAH is dispersed at the interface between MVQ and PA12, creating an encapsulated structure of MVQ@POE-g-MAH. This enhancement significantly broadens the potential applications of PA12 by improving its toughness, and resistance to both low and high temperatures, as well as impact endurance.

Nylons with Applications in Energy Generators, 3D Printing and Biomedicine.

Linear polyamides, known as nylons, are a class of synthetic polymers with a wide range of applications due to their outstanding properties, such as chemical and thermal resistance or mechanical strength. These polymers have been used in various fields: from common and domestic applications, such as socks and fishing nets, to industrial gears or water purification membranes. By their durability, flexibility and wear resistance, nylons are now being used in addictive manufacturing technology as a good material choice to produce sophisticated devices with precise and complex geometric shapes. Furthermore, the emergence of triboelectric nanogenerators and the development of biomaterials have highlighted the versatility and utility of these materials. Due to their ability to enhance triboelectric performance and the range of applications, nylons show a potential use as tribo-positive materials. Because of the easy control of their shape, they can be subsequently integrated into nanogenerators. The use of nylons has also extended into the field of biomaterials, where their biocompatibility, mechanical strength and versatility have paved the way for groundbreaking advances in medical devices as dental implants, catheters and non-absorbable surgical sutures. By means of 3D bioprinting, nylons have been used to develop scaffolds, joint implants and drug carriers with tailored properties for various biomedical applications. The present paper aims to collect evidence of these recently specific applications of nylons by reviewing the literature produced in recent decades, with a special focus on the newer technologies in the field of energy harvesting and biomedicine.

In Situ Growth of Highly Compatible Cu2O-GO Hybrids Via Amino-Modification for Melt-Spun Efficient Antibacterial Polyamide 6 Fibers.

Polyamide 6 (PA6) fiber has the advantages of high strength and good wear resistance. However, it is still challenging to effectively load inorganic antibacterial agents into polymer substrates without antimicrobial activity. In this work, graphene oxide is used as a carrier, which is modified with an aminosilane coupling agent (AEAPTMS) to enhance the compatibility and antimicrobial properties of the inorganic material, as well as to improve its thermal stability in a high-temperature melting environment. Cuprous oxide-loaded aminated grapheme (Cu2O-GO-NH2) is constructed by in situ growth method, and further PA6/Cu2O-GO-NH2 fibers are prepared by in situ polymerization. The composite fiber has excellent washing resistance. After 50 times of washing, its bactericidal rates against Bacillus subtilis and Escherichia coli are 98.85% and 99.99%, respectively. In addition, the enhanced compatibility of Cu2O-GO-NH2 with the PA6 matrix improves the orientation and crystallinity of the composite fibers. Compared with PA6/Cu2O-GO fibers, the fracture strength of PA6/Cu2O-GO-NH2 fibers increases from 3.0 to 4.2 cN/dtex when the addition of Cu2O-GO-NH2 is 0.2 wt%. Chemical modification and in situ concepts help to improve the compatibility of inorganic antimicrobial agents with organic polymers, which can be applied to the development of medical textiles.

Optimized preparation route for polyamide top-coated forward osmosis membrane for enhanced water flux using industrial wastewater as feed.

The forward osmosis (FO) process has recently gained significant interest in treating wastewater, brackish/seawater and concentrating feedstocks for various operations, including desalination. The study investigates the effect of different synthesis conditions of the polyamide-based thin-film composite (TFC) FO membranes on the membranes' final performance. Taguchi statistical analyses were used to fabricate and optimize the polyamide TFC FO membrane. The process parameters as factors were the amount of polyethersulfone (PES), polyethylene glycol 400 (PEG-400), polyvinyl pyrrolidone (PVP), m-phenylenediamine (MPD), and trimesoyl chloride (TMC), and TMC reaction-time (RT). The Taguchi method was adopted to investigate the optimal conditions and the significance of individual factors using an L16 (45) orthogonal array. Another Taguchi analysis (Taguchi 2) was adopted to investigate the influence of other important parameters like optimal conditions for MPD, TMC, and TMC reaction-time factors using an L9 (33) orthogonal array. Confirmation tests validated a maximum water flux of 46.4 ± 2.32 L/m2·h with a specific combination of control factors for membrane synthesis: PES/PEG/PVP/MPD/TMC/TMC RT-16/7/0.5/1/0.05/30. These tests demonstrated a high-water flux of 7.05 ± 0.35 L/m2·h when exposed to industrial wastewater (secondary effluent) as the feed solution (FS) and fertilizer as the draw solution (DS) in the FO process. The R2 values were more than 90%. The experimental validation confirmed the models' predictive ability with different FSs, including industrial wastewater.

A Novel Strategy for Fabrication of Polyamide 66/Nanohydroxyapatite Composite Bone Repair Scaffolds by Low-Temperature Three-Dimensional Printing.

Due to the decomposition temperature of Polyamide 66 (PA66) in the environment is close to its thermoforming temperature, it is difficult to construct porous scaffolds of PA66/nanohydroxyapatite (PA66/HAp) by fused deposition modeling (FDM) three-dimensional (3D) printing. In this study, we demonstrated for the first time a method for 3D printing PA66/HAp composites at room temperature, prepared PA66/HAp printing ink using a mixed solvent of formic acid/dichloromethane (FA/DCM), and constructed a series of composite scaffolds with varying HAp content. This printing system can print composite materials with a high HAp content of 60 wt %, which is close to the mineral content in natural bone. The physicochemical evaluation presented that the hydroxyapatite was uniformly distributed within the PA66 matrix, and the PA66/HAp composite scaffold with 30 wt % HAp content exhibited optimal mechanical properties and printability. The results of in vitro cell culture experiments indicated that the incorporation of HAp into the PA66 matrix significantly improved the cell adhesion, proliferation, and osteogenic differentiation of bone marrow stromal cells (BMSCs) cultured on the scaffold. In vivo animal experiments suggested that the PA66/HAp composite material with 30 wt % HAp content had the best structural maintenance and osteogenic performance. The three-dimensional PA66/HAp composite scaffold prepared by low temperature printing in the current study holds great potential for the repair of large-area bone defects.