Rectenna System Development Using Harmonic Balance and S-Parameters for an RF Energy Harvester.

With the escalating demand for Radio Frequency Identification (RFID) technology and the Internet of Things (IoT), there is a growing need for sustainable and autonomous power solutions to energize low-powered devices. Consequently, there is a critical imperative to mitigate dependency on batteries during passive operation. This paper proposes the conceptual framework of rectenna architecture-based radio frequency energy harvesters' performance, specifically optimized for low-power device applications. The proposed prototype utilizes the surroundings' Wi-Fi signals within the 2.4 GHz frequency band. The design integrates a seven-stage Cockroft-Walton rectifier featuring a Schottky diode HSMS286C and MA4E2054B1-1146T, a low-pass filter, and a fractal antenna. Preliminary simulations conducted using Advanced Design System (ADS) reveal that a voltage of 3.53 V can be harvested by employing a 1.57 mm thickness Rogers 5880 printed circuit board (PCB) substrate with an MA4E2054B1-1146T rectifier prototype, given a minimum power input of -10 dBm (0.1 mW). Integrating the fabricated rectifier and fractal antenna successfully yields a 1.5 V DC output from Wi-Fi signals, demonstrable by illuminating a red LED. These findings underscore the viability of deploying a fractal antenna-based radio frequency (RF) harvester for empowering small electronic devices.

Modeling of Schottky diode and optimal matching circuit design for low power RF energy harvesting.

This work designs and implements a single-stage rectifier-based RF energy harvesting device. This device integrates a receiving antenna and a rectifying circuit to convert ambient electromagnetic energy into useful DC power efficiently. The rectenna is carefully engineered with an optimal matching circuit, achieving high efficiency with a return loss of less than -10 dB. The design uses a practical model of the Schottky diode, where both RF and DC characteristics are derived through extensive experimental measurements. The results from both experiments and simulations confirm the effectiveness of the design, showing its proficiency in efficient RF energy harvesting under low-power conditions. The antenna produced operates in the wifi band with a gain close to 4 dBi and a bandwidth of 100 MHz. With a load resistance of 1600 Ω, the proposed device achieves an impressive RF-to-DC conversion efficiency of approximately 52% at a low incident power of -5 dBm. These findings highlight the potential and reliability of rectenna systems for practical and efficient RF energy harvesting applications. The study significantly contributes to our understanding of rectenna-based energy harvesting, providing valuable insights for future design considerations and applications in low-power RF systems.

Optimizing an electromagnetic wave absorber for bi-anisotropic metasurfaces based on toroidal modes.

The design and optimization of an electromagnetic wave absorber for far-field wireless power transmission (WPT) is the subject of this research study. The goal of the research is to effectively absorb energy from ambient RF electromagnetic waves without the usage of a ground plane by employing metasurfaces with chiral components.By integrating trioidal moments into the design theory, the objective is to create a metasurface that functions in two frequency bands and produces high-quality resonance. The study also explores the dual non-homogeneity property of structures, polarization tensor coefficients, and the electromagnetic response of non-homogeneous metasurfaces. Based on the relative orientation of induced fields and moments, it delves deeper into the two basic possibilities for dual non-homogeneous elements. The development of chiral metasurfaces and the notion of electromagnetic chirality and its implications for polarization properties are introduced.

Wearable All-Fabric Hybrid Energy Harvester to Simultaneously Harvest Radiofrequency and Triboelectric Energy.

Distributed micro-energy harvesting devices offer the flexibility, sustainability, and multi-scenario applicability that will be critical to wearable electronic products in the Internet of Things. The radiofrequency and triboelectric (RF-TE) hybrid energy harvester (HEH) concept and prototype is presented for the first time, to simultaneously capture the energy from ambient electromagnetic waves and biological motions. The proposed hybrid energy harvesting system consists of a wearable rectenna, a triboelectric nanogenerator (TENG), and a power management circuit (PMC). Among them, the all-fabric rectenna exhibits good impedance matching characteristics in the ISM frequency. The flexible TENG unit can generate a maximum power density of 0.024 µW cm-2. The designed multifunctional fabric-based PMC can considerably enhance the controllability of harvested hybrid energy. Additionally, a normalizable fabric circuit board quasi surface mount technology (FCB-SMT) is proposed to integrate all modules on the same fabric substrate in one step, making the entire system superior mechanical robustness. The proposed wearable fabric-based RF-TE hybrid energy harvester is capable of successfully driving consumer electronics (such as sensors, watches, etc.). It provides a new energy solution strategy for self-powered wearable electronic devices and is anticipated to encourage the efficient utilization of renewable energy.

Design and Simulation of Tunneling Diodes with 2D Insulators for Rectenna Switches.

Rectenna is the key component in radio-frequency circuits for receiving and converting electromagnetic waves into direct current. However, it is very challenging for the conventional semiconductor diode switches to rectify high-frequency signals for 6G telecommunication (>100 GHz), medical detection (>THz), and rectenna solar cells (optical frequencies). Such a major challenge can be resolved by replacing the conventional semiconductor diodes with tunneling diodes as the rectenna switches. In this work, metal-insulator-metal (MIM) tunneling diodes based on 2D insulating materials were designed, and their performance was evaluated using a comprehensive simulation approach which includes a density-function theory simulation of 2D insulator materials, the modeling of the electrical characteristics of tunneling diodes, and circuit simulation for rectifiers. It is found that novel 2D insulators such as monolayer TiO2 can be obtained by oxidizing sulfur-metal layered materials. The MIM diodes based on such insulators exhibit fast tunneling and excellent current rectifying properties. Such tunneling diodes effectively convert the received high-frequency electromagnetic waves into direct current.

A Compact Stacked RF Energy Harvester with Multi-Condition Adaptive Energy Management Circuits.

This paper presents a compact stacked RF energy harvester operating in the WiFi band with multi-condition adaptive energy management circuits (MCA-EMCs). The harvester is divided into antennas, impedance matching networks, rectifiers, and MCA-EMCs. The antenna is based on a polytetrafluoroethylene (PTFE) substrate using the microstrip antenna structure and a ring slot in the ground plane to reduce the antenna area by 13.7%. The rectifier, impedance matching network, and MCA-EMC are made on a single FR4 substrate. The rectifier has a maximum conversion efficiency of 33.8% at 5 dBm input. The MCA-EMC has two operating modes to adapt to multiple operating conditions, in which Mode 1 outputs 1.5 V and has a higher energy conversion efficiency of up to 93.56%, and Mode 2 supports a minimum starting input voltage of 0.33 V and multiple output voltages of 2.85-2.45 V and 1.5 V. The proposed RF energy harvester is integrated by multiple-layer stacking with a total size of 53 mm × 43.5 mm × 5.9 mm. The test results show that the proposed RF energy harvester can drive a wall clock (30 cm in diameter) at 10 cm distance and a hygrometer at 122 cm distance with a home router as the transmitting source.

A Compact RF Energy Harvesting Wireless Sensor Node with an Energy Intensity Adaptive Management Algorithm.

This paper presents a compact RF energy harvesting wireless sensor node with the antenna, rectifier, energy management circuits, and load integrated on a single printed circuit board and a total size of 53 mm × 59.77 mm × 4.5 mm. By etching rectangular slots in the radiation patch, the antenna area is reduced by 13.9%. The antenna is tested to have an S11 of -24.9 dB at 2.437 GHz and a maximum gain of 4.8 dBi. The rectifier has a maximum RF-to-DC conversion efficiency of 52.53% at 7 dBm input energy. The proposed WSN can achieve self-powered operation at a distance of 13.4 m from the transmitter source. To enhance the conversion efficiency under different input energy densities, this paper establishes an energy model for two operating modes and proposes an energy-intensity adaptive management algorithm. The experiments demonstrated that the proposed WSN can effectively distinguish between the two operating modes based on input energy intensity and realize efficient energy management.

Multiband Microstrip Rectenna Using ZnO-Based Planar Schottky Diode for RF Energy Harvesting Applications.

This paper presents a single-substrate microstrip rectenna for dedicated radio frequency energy harvesting applications. The proposed configuration of the rectenna circuit is composed of a clipart moon-shaped cut in order to improve the antenna impedance bandwidth. The curvature of the ground plane is modified with a simple U-shaped slot etched into it to improve the antenna bandwidth by changing the current distribution; therefore, this affects the inductance and capacitance embedded into the ground plane. The linear polarized ultra-wide bandwidth (UWB) antenna is achieved by using 50 Ω microstrip line and build on Roger 3003 substrate with an area of 32 × 31 mm2. The operating bandwidth of the proposed UWB antenna extended from 3 GHz to 25 GHz at -6 dB reflection coefficient (VSWR ≤ 3) and extended from both 3.5 to 12 GHz, from 16 up to 22 GHz at -10 dB impedance bandwidth (VSWR ≤ 2). This was used to harvest RF energy from most of the wireless communication bands. In addition, the proposed antenna integrates with the rectifier circuit to create the rectenna system. Moreover, to implement the shunt half-wave rectifier (SHWR) circuit, a planar Ag/ZnO Schottky diode uses a diode area of 1 × 1 mm2. The proposed diode is investigated and designed, and its S-parameter is measured for use in the circuit rectifier design. The proposed rectifier has a total area of 40 × 9 mm2 and operates at different resonant frequencies, namely 3.5 GHz, 6 GHz, 8 GHz, 10 GHz and 18 GHz, with a good agreement between simulation and measurement. The maximum measured output DC voltage of the rectenna circuit is 600 mV with a maximum measured efficiency of 25% at 3.5 GHz, with an input power level of 0 dBm at a rectifier load of 300 Ω.

A Dual-Polarized Omnidirectional Rectenna Array for RF Energy Harvesting.

In this paper, a dual-polarized omnidirectional rectenna array using a hybrid power-combining scheme is proposed for the applications of RF energy harvesting. In the antenna design part, two omnidirectional antenna subarrays are created to receive horizontally polarized electromagnetic (EM) waves and a four-dipole subarray is produced to receive vertically polarized incoming EM waves. The two antenna subarrays of different polarizations are combined and optimized, so as to reduce the mutual influence between them. In this way, a dual-polarized omnidirectional antenna array is realized. In the rectifier design part, a half-wave rectifying structure is adopted for converting the RF energy into DC energy. Based on the Wilkinson power divider and 3-dB hybrid coupler structure, a power-combining network is designed to connect the whole antenna array and rectifiers. The proposed rectenna array is fabricated and measured under different RF energy harvesting scenarios. All simulated and measured results are in good agreement, which verifies the capabilities of the designed rectenna array.

Nanomaterials and Devices for Harvesting Ambient Electromagnetic Waves.

This manuscript presents an overview of the implications of nanomaterials in harvesting ambient electromagnetic waves. We show that the most advanced electromagnetic harvesting devices are based on oxides with a thickness of few nanometers, carbon nanotubes, graphene, and molybdenum disulfide thanks to their unique physical properties. These tiny objects can produce in the years to come a revolution in the harvesting of energy originating from the Sun, heat, or the Earth itself.

Radiofrequency Energy Harvesting Systems for Internet of Things Applications: A Comprehensive Overview of Design Issues.

Radiofrequency energy harvesting (RF-EH) solutions have evolved significantly in recent years due to the ubiquity of electromagnetic waves in any environment. This review presents a comprehensive report on autonomous wireless sensor (WS) design considerations based on RF-EH. The obtainability of RF-EH-WS is driven by development efforts in the areas of RF-EH circuit design, known as rectifying antenna (Rectenna), the minimization of the energy budget of WS (MEB-WS), and finally, power management modules (PMM). The PMM aims to optimize the energy efficiency of the WS. In addition to these three factors, examining the RF power levels harvested related to the rectenna feeding technique (RFT) is essential. Since we did not find any review presenting a holistic view of these design considerations, we strived to provide a detailed picture of recent advances and new enhancements in this review. To address this issue, this review gives an overview of the seminal and contemporary studies in the RF-EH-WS field. The IoT issues are also discussed in terms of their basic requirement to support reduced size or miniaturized smart objects, which are common matters in current applications of WS nodes. Potential open issues that might be considered for future research are also discussed in this article. For a more detailed description of all presented concepts, many significant references are provided for the readers.

Scalable, Dual-Band Metasurface Array for Electromagnetic Energy Harvesting and Wireless Power Transfer.

A dual-band metasurface array is presented in this paper for electromagnetic (EM) energy harvesting in the Wi-Fi band and Ku band. The array consists of metasurface unit cells, rectifiers, and load resistors. The metasurface units within each column are interconnected to establish two channels of energy delivery, enabling the transmission and aggregation of incident power. At the terminals of two channels, a single series diode rectifier and a voltage doubler rectifier are integrated into them to rectify the energy in the Wi-Fi band and the Ku band, respectively. A 7 × 7 prototype of the metasurface array is fabricated and tested. The measured results in the anechoic chamber show that the RF-to-dc efficiencies of the prototype at 2.4 GHz and 12.6 GHz reach 64% and 55% accordingly, when the available incident power at the surface is 3 dBm and 14 dBm, respectively.

Passive and Flexible Wireless Electronics Fabricated on Parylene/PDMS Substrate for Stimulation of Human Stem Cell-Derived Cardiomyocytes.

In this paper, we report the development of a wireless, passive, biocompatible, and flexible system for stimulation of human induced pluripotent stem cell derived cardiomyocytes (hiPSC-CMS). Fabricated on a transparent parylene/PDMS substrate, the proposed stimulator enables real-time excitation and characterization of hiPSC-CMs cultured on-board. The device comprises a rectenna operating at 2.35 GHz which receives radio frequency (RF) energy from an external transmitter and converts it into DC voltage to deliver monophasic stimulation. The operation of the stimulator was primarily verified by delivering monophasic voltage pulses through gold electrodes to hiPSC-CMs cultured on the Matrigel-coated substrates. Stimulated hiPSC-CMs beat in accordance with the monophasic pulses when delivered at 0.5, 1, and 2 Hz pulsing frequency, while no significant cell death was observed. The wireless stimulator could generate monophasic pulses with an amplitude of 8 V at a distance of 15 mm. These results demonstrated the proposed wireless stimulator's efficacy for providing electrical stimulation to engineered cardiac tissues. The proposed stimulator will have a wide application in tissue engineering where a fully wireless stimulation of electroconductive cells is needed. The device also has potential to be employed as a cardiac stimulator by delivering external stimulation and regulating the contractions of cardiac tissue.

Self-Sustainable Biomedical Devices Powered by RF Energy: A Review.

Wearable and implantable medical devices (IMDs) have come a long way in the past few decades and have contributed to the development of many personalized health monitoring and therapeutic applications. Sustaining these devices with reliable and long-term power supply is still an ongoing challenge. This review discusses the challenges and milestones in energizing wearable and IMDs using the RF energy harvesting (RFEH) technique. The review highlights the main integrating frontend blocks such as the wearable and implantable antenna design, matching network, and rectifier topologies. The advantages and bottlenecks of adopting RFEH technology in wearable and IMDs are reviewed, along with the system elements and characteristics that enable these devices to operate in an optimized manner. The applications of RFEH in wearable and IMDs medical devices are elaborated in the final section of this review. This article summarizes the recent developments in RFEH, highlights the gaps, and explores future research opportunities.

2D Material-Enabled Optical Rectennas with Ultrastrong Light-Electron Coupling.

Optical rectennas extend the electromagnetic wave rectification process into the visible regime and provide a route toward high-performance photodetection and energy harvesting. Here, the promise of 2D materials toward on-chip optical rectennas is demonstrated. A self-aligned patterning process yields lateral MIM structures where a nanometer-sized air gap separates a 2D material contact from a metal electrode. This device can be scalably produced in large arrays using established microfabrication techniques. Different from previous approaches, the performance of the 2D rectenna can be adjusted through electrostatic gating. Optimization of the band alignment leads to strong rectification at wavelengths around 500 nm and clear polarization control. Comparison of wavelength-dependent rectenna performance with a photon-assisted tunneling model reveals a tenfold increase in photon-electron coupling over nanotube-based rectennas. The results highlight the potential of 2D material-based rectennas for future quantum computing applications.

Radio Frequency Energy Harvesting Technologies: A Comprehensive Review on Designing, Methodologies, and Potential Applications.

Radio frequency energy harvesting (RF-EH) is a potential technology via the generation of electromagnetic waves. This advanced technology offers the supply of wireless power that is applicable for battery-free devices, which makes it a prospective alternative energy source for future applications. In addition to the dynamic energy recharging of wireless devices and a wide range of environmentally friendly energy source options, the emergence of the RF-EH technology is advantageous in facilitating various applications that require quality of service. This review highlights the abundant source of RF-EH from the surroundings sources, including nearby mobile phones, Wi-Fi, wireless local area network, broadcast television signal or DTS, and FM/AM radio signals. In contrast, the energy is captured by a receiving antenna and rectified into a working direct current voltage. This review also summarizes the power of RF-EH technology, which would provide a guideline for developing RF-EH units. The energy harvesting circuits depend on cutting-edge electrical technology to achieve significant efficiency, given that they are built to perform with considerably small current and voltage. Hence, the review includes a thorough analysis and discussion of various RF designs and their pros and cons. Finally, the latest applications of RF-EH are presented.

Tri-Band Rectenna Dedicated to UHF RFID, GSM-1800 and UMTS-2100 Frequency Bands.

The omnipresence of connected objects leads to the quasi-permanent presence of electromagnetic waves from different sources in our environment. This article presents a new electromagnetic energy harvesting device, rectenna type, which offers the advantage of being versatile. Indeed, the proposed prototype is compatible with three frequency bands of radio standards widely deployed today (UHF RFID, GSM-1800, and UMTS-2100), and its performances remain good for low to very low ambient power levels as well as for different loads depending on the targeted application. The proposed solution is based on a tri-band antenna with very good efficiency and a bandwidth of at least 80 MHz for each of the operating frequencies. Moreover, the associated rectifier circuit is also tri-band and offers good performance in terms of RF-to-DC conversion efficiency for input levels varying in a rather wide range of power levels. The study is based on a design phase by simulation until the realization of prototypes and their experimental characterization. The designed rectenna is compared with solutions found in the literature.

A New RF Energy Harvesting System Based on Two Architectures to Enhance the DC Output Voltage for WSN Feeding.

In this paper, a new RF Energy Harvesting (RF-EH) system for Wireless Sensor Network (WSN) feeding is proposed. It is based on two different monitored architectures using switch circuits controlled by the input powers. One architecture is more adapted to high input powers and the other to low input powers. The two different architectures and the system are designed and realized on Teflon glass substrate with a relative permittivity of 2.1 and thickness of 0.67 mm. They are tested separately as a function of the distance from the relay antenna. A new multiband antenna with a size of 40 × 30 mm2 is used for both architectures and the system. The measured antenna gains are 2.7 dB, 2.9 dB, and 2.55 dB for the frequencies of 1.8 GHz, 2.1 GHz, and 2.66 GHz corresponding to the mobile communication networks, respectively. The rectifier consists of two Schottky diodes forming a full-wave rectifier and voltage doubler. The maximum measured RF-to-DC conversion efficiency is 71.5%. The proposed RF-EH system provides a maximum DC output voltage of 5.6 V and 3.15 V for an open and 2 kΩ resistance load, respectively.

Toward Next-Generation Mobile Diagnostics: Near-Field Communication-Powered Electrochemiluminescent Detection.

Mobile phones have been used in combination with point of care (PoC) devices for over a decade now. However, their use seems restricted to the detection of sensing events using the video and camera functions. In contrast, the complementary ability to use mobile phones to power such PoC devices has been largely unexplored. This work demonstrates the proof-of-principle that a smartphone can be used to both power and analyze an electrochemiluminescence (ECL) detection system. A printed device is presented featuring an electrochemical cell connected in series to a rectenna that is able to use the Near Field Communication (NFC, 13.56 MHz) signal to provide the energy needed to generate ECL from Ru(bpy)32+/tri-n-propylamine. The emitted light, the intensity of which is directly proportional to the concentration of the ruthenium complex, can then be captured by the mobile phone camera and analyzed. This work presents the fabrication and the electrical and electrochemical characterization of the device. Effective voltages ranging from 0.90 to 4.50 V have been recorded, depending on the coupling between emitter and receiver, which translate into working electrode potentials ranging from 0.76 up to 1.79 V vs Ag. Detection and quantification limits of 0.64 and 1.52 µM, respectively, have been achieved for Ru(bpy)32+, and linear ranges up to 0.1 mM (red channel) and no less than 1.0 mM (green channel) have been found.

A Broad Dual-Band Implantable Antenna for RF Energy Harvesting and Data Transmitting.

An implantable antenna, operating at the dual Industrial, Scientific, and Medical (ISM) bands of 902-928 MHz and 2.4-2.48 GHz, is presented for RF energy harvesting and data transmission. By introducing multiple radiating branches and etching a C-shaped slot, multiple resonant frequencies were generated to produce the wide dual bands. The proposed antenna has compact dimensions of 7.9 × 7.7 × 1.27 mm3. The simulated impedance bandwidths of the antenna are 0.67-1.05 GHz (44.2%) and 2.11-2.96 GHz (33.5%), and the peak gains are -28.9 dBi and -29.5 dBi, respectively. The lower band can be applied in RF energy harvesting, while the upper band is designed for data transmission with external medical equipment. Furthermore, to convert RF power into DC power, in RF energy harvesting, a voltage-doubled rectifier was positioned under the ground plane of the proposed antenna. The rectifier circuit can achieve a maximum conversion efficiency of 52% at an input power of 5 dBm. Furthermore, the integrated scheme of the implantable rectenna was fabricated and the numerical performance of the wireless power transfer was verified with the measurement results.