RESUMO
Titanium (Ti) and its alloys are known to exhibit room-temperature fracture toughness below 130 MPa m1/2, only about one half of the best austenitic stainless steels. It is purported that this is not the best possible fracture resistance of Ti, but a result of oxygen impurities that sensitively retard the activities of plasticity carriers in this hexagonal close-packed metal. By a reduction of oxygen content from the 0.14 wt% in commercial purity Ti to 0.02 wt%, the mode-Ι fracture toughness of the low-oxygen Ti is measured to be as high as KJ Ic ≈ 255 MPa m1/2, corresponding to J-integral-based crack-initiation toughness of up to JIc ≈ 537 kJ m-2. This extraordinary toughness, reported here for the first time for pure Ti, places Ti among the toughest known materials. The intrinsic high fracture resistance is attributed to the profuse plastic deformation in a significantly enlarged plastic zone, rendered by the pronounced deformation twinning ahead of the crack tip along with ample twin-stimulated ãc+aã dislocation activities, in the absence of impeding oxygen. Controlling the content of a property-controlling impurity thus holds the promise to be a readily applicable strategy to reach for unprecedented damage tolerance in some other structural alloys.
RESUMO
As a high-performance polymer with exceptional mechanical, thermal, and insulating properties, polyimide (PI) has been widely used as flexible circuit substrates for microelectronics, portable electronics, and wearable devices. Due to the growing demand for further thinning and lightweighting of electronic products, PI films need to have further enhanced mechanical properties. Traditional nanofiller-reinforced PI films often exhibit reduced ductility and limited improvements in strength. Therefore, it remains a challenge to simultaneously improve the strength and toughness of PI films while preserving their ductility. In this study, we report an exceptionally strong and ductile PI doubly reinforced by one-dimensional rigid-rod para-aramid, poly(p-aminophenylene aminoterephthalamide ((NH2)2-PPTA), and two-dimensional graphene oxide (GO) nanosheets. The amino side groups of (NH2)2-PPTA react with the anhydride end groups of PI, forming covalent bonds. At a (NH2)2-PPTA content of only 0.4 wt %, the (NH2)2-PPTA/PI film displays significantly enhanced mechanical properties. When 0.4 wt % of GO is added together with (NH2)2-PPTA, the tensile strength, tensile toughness, and strain at break reach 284.8 ± 5.3 MPa, 277.9 ± 7.6 MJ/m3, and 132.6 ± 3.8%, which are â¼178, â¼312, and â¼51% higher, respectively, than those of pure PI. Moreover, the doubly reinforced PI film also exhibits a 206% increase in tear strength and significantly enhanced folding resistance. The dual reinforcement of PI with (NH2)2-PPTA and GO improves the mechanical properties more efficiently than any single reinforcing agents previously reported and overcomes the disadvantage of most inorganic nanofillers that reduce ductility.
RESUMO
Choking susceptibility refers to the propensity of an athlete to choke under pressure. Mesagno has operationalized choking susceptibility as a combination of scores on self-consciousness, anxiety and coping. Despite the potential of Mesagno's protocol, there is currently limited support for its validity. Secondly, although mental toughness (MT) has a relationship with sport performance, there is limited research on its relationship to choking under pressure, specifically. The current study investigated the relationship between choking susceptibility and mental toughness. It was hypothesized that choking susceptible athletes will have significantly lower levels of mental toughness than those who are not choking susceptible. Data from a heterogeneous sample of athletes (N = 415) was obtained through a Qualtrics research panel. Results of a Mann-Whitney U showed that self-reported mental toughness was not significantly different in athletes categorized as choking susceptible and non-choking susceptible. Correlational analyses also highlighted differences between mental toughness and the composite scores of choking susceptibility, which provide researchers with avenues for future research in this area alongside a need for each construct to be examined in relation to choking behavior in sport.
RESUMO
For damage tolerance design in engineering components, the fracture toughness value, KIC, of the material is essential. However, obtaining specimens of sufficient thickness from stir friction welded plates is challenging, and often, the experimental test values do not meet the necessary criteria, preventing the experimental fracture toughness, Kq, from being recognized as plane strain fracture toughness KIC. The fracture toughness Kq of 2195 Al-Li alloy welding seams with different thicknesses was measured on the forward and backward sides. Microstructure characterization was conducted by scanning electron microscope (SEM). The results indicated minimal significant differences in grain size between the advancing and retreating sides of the weld nugget zone. In specimens of the same thickness, fracture toughness measurements along the normal direction of the joint cross-section showed a high similarity between the advancing and retreating sides of the weld nugget zone. Utilizing the quantitative relationships between fracture toughness and sample thickness derived from both the fracture K and G criteria, it is possible to predict the fracture toughness of thick plates using thin plates. This study employs these relationships to calculate the fracture toughness KIC of 2195 aluminum-lithium alloy friction stir welds. The KIC values obtained are 41.65 MPa·m1/2 from the fracture K criterion and 43.54 MPa·m1/2 from the fracture G criterion.
RESUMO
High-carbon steels are normally used as tool materials. The use of such steels for construction is limited due to their increased brittleness and poor weldability. However, it appears that high-carbon steels possess certain hidden reserves for enhanced plasticity and strength if properly heat-treated. An unconventional heat treatment was applied to carbon eutectoid steel (0.8 wt.% C) in order to increase its strength and impact toughness simultaneously. Samples for tensile and impact testing were held at 800 °C for different time ranges from 3 min to 9 min with subsequent cooling in oil. It was established that for each type of sample, an optimal holding time exists that is responsible for increased strength and high impact toughness. The hardness and microhardness levels of the surface and under-surface regions of the samples reached 390 HV after optimal heat treatment. An X-ray revealed a shift of the (211)α-peak to the lower 2-theta angles after heat treatment with the optimal holding time; this indicates an increase in carbon content in alpha solid solutions of approximately 0.12 wt.%. Thus, a nanostructured mixture of low-carbon martensite and thin cementite plates is formed in the under-surface region of carbon eutectoid steel after heat treatment, with a controlled holding time at the austenitizing temperature.
RESUMO
Thermomechanical processing (TMP) of ferritic-martensitic (FM) steels, such as HT9 (Fe-12Cr-1MoWV) steels, involves normalizing, quenching, and tempering to create a microstructure of fine ferritic/martensitic laths with carbide precipitates. HT9 steels are used in fast reactor core components due to their high-temperature strength and resistance to irradiation damage. However, traditional TMP methods for these steels often result in performance limitations under irradiation, including embrittlement at low temperatures (<~430 °C), insufficient strength and toughness at higher temperatures (>500 °C), and void swelling after high-dose irradiation (>200 dpa). This research aimed to enhance both fracture toughness and strength at high temperatures by creating a quenched and tempered martensitic structure with ultrafine laths and precipitates through rapid quenching and unconventional tempering. Mechanical testing revealed significant variations in strength and fracture toughness depending on the processing route, particularly the tempering conditions. Tailored TMP approaches, combining rapid quenching with limited tempering, elevated strength to levels comparable to nano-oxide strengthened ferritic alloys while preserving fracture toughness. For optimal properties in high-Cr steels for future reactor applications, this study recommends a modified tempering treatment, i.e., post-quench annealing at 500 °C or 600 °C for 1 h, possibly followed by a brief tempering at a slightly higher temperature.
RESUMO
ScAlMgO4 (SCAM), which can be used as an epitaxial substrate material of GaN in power devices, faces the challenge of achieving a high-quality surface by ultra-precision polishing due to its brittle and easily cleaved characteristics, which are closely associated with its mechanical properties. The micromechanical properties of SCAM single crystals were evaluated by nanoindentation and microscratch tests using different indenters. The elastic modulus EIT and the indentation hardness HIT of SCAM obtained by nanoindentation were 226 GPa and 12.1 GPa, respectively. Leaf-shaped chips and the associated step-like planes of SCAM can be found in the severely damaged regime during scratching by Berkovich and Vickers indenters with sharp edges due to the intersection of intense radial and lateral cracks. The fracture toughness (Kc = 1.12 MPa·m1/2) of SCAM can be obtained by using a scratch-based methodology for a spherical indenter based on linear elastic fracture mechanics (LEFM) under an appropriate range of applied loads. An optimal expression for calculating the fracture toughness of easily cleaved materials, including SCAM, via the Vickers indenter-induced cracking method using a Berkovich indenter was recommended.
RESUMO
Introduction: This meta-analysis investigates the relationships between the Dark Triad personality traits (narcissism, Machiavellianism, and psychopathy) and mental toughness. Previous research has shown mixed results regarding the influence of these traits on mental toughness. The objective of this meta-analysis is to synthesize existing literature and provide a comprehensive understanding of how Dark Triad traits correlate with mental toughness. Methods: A comprehensive literature search was conducted in 7 databases, Data were extracted by correlation and analyzed using a random-effects model. Results: The results yielding 27 effect sizes with a total of 12,378 participants, revealed a significant moderate positive association between narcissism and mental toughness (r = 0.327, p < 0.001), suggesting that individuals with higher levels of narcissism tend to exhibit greater mental toughness. However, no significant associations were found between Machiavellianism (r = 0.023, p = 0.719) or psychopathy (r = -0.022, p = 0.625) and mental toughness. Discussion: The findings contribute to a more nuanced understanding of the Dark Triad traits and their differential associations with adaptive psychological constructs, highlighting the unique role of narcissism in mental toughness. This meta-analysis provides valuable insights for future research and practical applications in fostering adaptive aspects of narcissism while mitigating its potential maladaptive consequences.
RESUMO
Due to the swift progress in the construction sector, there is a global concern about the potential scarcity of river sand and freshwater resources. The development of new construction materials is considered an inevitable trend for industry growth. PVA fibers, known for their strong corrosion resistance, cost-effectiveness, and high toughness, have the potential to enhance the corrosion resistance and seismic performance of structures in marine environments. However, their mechanical properties and durability in the seawater and sea sand environment are not well understood. Therefore, the investigation of the impact of seawater and sea sand on the mechanical properties and durability of PVA fiber-reinforced cement composites is considered crucial. A mechanical performance analysis of PVA fiber-reinforced seawater and sea sand fiber cement composites was conducted in this study. PVA fiber volume fractions of 0%, 0.75%, and 1.5%, cement composite matrix strength grades of C30 and C50, and curing periods of 28 days, 90 days, and 180 days were examined, investigating their influence on the bending toughness of PVA fiber-reinforced seawater and sea sand cement composites. Specific conclusions include the addition of fibers increased the peak bending load, had a less corrosive effect in seawater, and improved the flexural toughness of the material. The most significant improvement was observed at 1.5% fiber content, where the load-deflection curve was fuller and the energy absorption capacity of the material increased by 33-109%, maintaining good bending toughness. Furthermore, higher fiber contents are required for high-strength cementitious composites to improve flexural toughness and durability. The formulation of calculation formulas for predicting bending strength and corresponding deflection, which fit well with the experimental results; and the development of a calculation model for the bending toughness index of PVA fiber-reinforced seawater and sea sand cement composites, providing an effective prediction of material bending toughness.
RESUMO
The importance of psychological performance skills (mental toughness) is recognised in many mission-critical professions. Similar importance has been suggested for nursing. Survey data demonstrate that surgical staff believe that such skills exert significant influence on surgical excellence, surgical errors and on managing surgical emergencies. However, few surgical staff receive such training. It is suggested that models exist to easily meet this training need and opportunity.
RESUMO
Designing heat-resistant thermosets with excellent comprehensive performance has been a long-standing challenge. Co-curing of various high-performance thermosets is an effective strategy, however, the traditional trial-and-error experiments have long research cycles for discovering new materials. Herein, a two-step machine learning (ML) assisted approach is proposed to design heat-resistant co-cured resins composed of polyimide (PI) and silicon-containing arylacetylene (PSA), that is, poly(silicon-alkyne imide) (PSI). First, two ML prediction models are established to evaluate the processability of PIs and their compatibility with PSA. Then, another two ML models are developed to predict the thermal decomposition temperature and flexural strength of the co-cured PSI resins. The optimal molecular structures and compositions of PSI resins are high-throughput screened. The screened PSI resins are experimentally verified to exhibit enhanced heat resistance, toughness, and processability. The research framework established in this work can be generalized to the rational design of other advanced multi-component polymeric materials.
RESUMO
The perforation characteristics and fracture-related mechanical properties of the tympanic membrane (TM) greatly affect surgical procedures like myringotomy and tympanostomy performed on the middle ear. We analyzed the most important features of the gerbil TM perforation using an experimental approach that was based on force measurement during a 2-cycle needle insertion/extraction process. Fracture energy, friction energy, strain energy, and hysteresis loss were taken into consideration for the analysis of the different stages of needle insertion and extraction. The results demonstrated that (1) although the TM shows viscoelastic behavior, the contribution of hysteresis loss was negligible compared to other irreversible dissipated energy components (i.e., fracture energy and friction energy). (2) The TM puncture force did not substantially change during the first hours after animal death, but interestingly, it increased after 1 week due to the drying effects of soft tissue. (3) The needle geometry affected the crack length and the most important features of the force-displacement plot for the needle insertion process (puncture force, puncture displacement, and jump-in force) increased with increasing needle diameter, whereas the insertion velocity only changed the puncture and jump-in forces (both increased with increasing insertion velocity) and did not have a noticeable effect on the puncture displacement. (4) The fracture toughness of the gerbil TM was almost independent of the needle geometry and was found to be around 0.33 ± 0.10 kJ/m2.
RESUMO
Polymer fibers that combine high toughness and heat resistance are hard to achieve, which, however, hold tremendous promise in demanding applications such as aerospace and military. This prohibitive design task exists due to the opposing property dependencies on chain dynamics because traditional heat-resistant materials with rigid molecular structures typically lack the mechanism of energy dissipation. Aramid nanofibers have received great attention as high-performance nanoscale building units due to their intriguing mechanical and thermal properties, but their distinct structural features are yet to be fully captured. We show that aramid nanofibers form nanoscale crimps during the removal of water, which primarily resides at the defect planes of pleated sheets, where the folding can occur. The precise control of such a structural relaxation can be realized by exerting axial loadings on hydrogel fibers, which allows the emergence of aramid fibers with varying angles of crimps. These crimped fibers integrate high toughness with heat resistance, thanks to the extensible nature of nanoscale crimps with rigid molecular structures of poly(p-phenylene terephthalamide), promising as a template for stable stretchable electronics. The tensile strength/modulus (392-944 MPa/11-29 GPa), stretchability (25-163%), and toughness (154-445 MJ/cm3) are achieved according to the degree of crimping. Intriguingly, a toughness of around 430 MJ/m3 can be maintained after calcination below the relaxation temperature (259 °C) for 50 h. Even after calcination at 300 °C for 10 h, a toughness of 310 MJ/m3 is kept, outperforming existing polymer materials. Our multiscale design strategy based on water-bearing aramid nanofibers provides a potent pathway for tackling the challenge for achieving conflicting property combinations.
RESUMO
Developing biodegradable polyurethane (PU) materials as an alternative to non-degradable petroleum-based PU is a crucial and challenging task. This study utilized lactide as the starting material to synthesize polylactide polyols (PLA-OH). PLA-based polyurethanes (PLA-PUs) were successfully synthesized by introducing PLA-OH into the PU molecular chain. A higher content of PLA-OH in the soft segments resulted in a substantial improvement in the mechanical attributes of the PLA-PUs. This study found that the addition of PLA-OH content significantly improved the tensile stress of the PU from 5.35 MPa to 37.15 MPa and increased the maximum elongation to 820.8%. Additionally, the modulus and toughness of the resulting PLA-PU were also significantly improved with increasing PLA-OH content. Specifically, the PLA-PU with 40% PLA-OH exhibited a high modulus of 33.45 MPa and a toughness of 147.18 MJ m-3. PLA-PU films can be degraded to carbon dioxide and water after 6 months in the soil. This highlights the potential of synthesizing PLA-PU using biomass-renewable polylactide, which is important in green and sustainable chemistry.
RESUMO
Most toughening methods for epoxy resins are usually used at the expense of other properties. Some polyhedral oligomeric silsesquioxanes (POSSs) with both a rigid Si-O-Si structure and flexible organic chain segments could be expected to be effective toughening agents. In this study, three reactive polyhedral oligomeric silsesquioxanes with a thiol group (OMPPS), a carboxyl group (OCOPS), and an epoxy group (OGCPS) were synthesized and characterized. They were utilized as modifiers to toughen 3-(oxiran-2-ylmethoxy)-N,N-bis(oxiran-2-ylmethyl)aniline (AFG-90MH)/4,4'-methylenebis(2-ethylaniline) (MOEA) (epoxy resin) with different molar ratios to obtain hybrid resins named OMPPS-EP-i, OCOPS-EP-j, and OGCPS-EP-k. The effects of the amount of modifier added and the length of the organic chain on the cage structure on various properties of the hybrid resins were investigated. The results show that all three modifiers show good compatibility with the epoxy resin. The hybrid resins have a low viscosity at 45~85 °C and can be cured at a low temperature (110 °C). The cured hybrid resins display improved toughness. Typically, the critical stress intensity factor (KIC) and impact strength of OGCPS-EP-0.6-C are 2.54 MPaâm-1/2 and 19.33 kJâm-2, respectively, which increased by 58.75% and 22.48% compared with the pristine epoxy resin, respectively. In addition, the glass transition temperature and flexural strength of the hybrid resins are basically unchanged.
RESUMO
The utilization of polyamide 10,12 (PA10,12) composites in various industries has been limited constrained by their inherent low toughness, making it a challenge to achieve a balance between toughness and structural integrity through conventional elastomer addition strategies. Herein, we introduce a straightforward method for the concurrent toughening and reinforcement of PA10,12 composites. This is accomplished by blending polyolefin elastomer (POE) and 3-pentadecylphenol (PDP) with the PA10,12 matrix. The incorporation of 5 wt% PDP effectively blurred the PA10,12/POE interface due to PDP's role as a compatibilizer. This phenomenon is attributed to the formation of intermolecular hydrogen bonds, as evidenced by Fourier Transform Infrared Spectroscopy (FTIR) analysis. Further investigation, using differential scanning calorimetry (DSC), elucidated the crystallization thermodynamics and kinetics of the resulting binary PA10,12/POE and ternary PA10,12/POE/PDP composites. Notably, the crystallization temperature (Tc) was observed to decrease from 163.1 °C in the binary composite to 161.5 °C upon the addition of PDP. Increasing the PDP content to 10% led to a further reduction in Tc to 159.5 °C due to PDP's capacity to slow down crystallization. Consequently, the ternary composite of PA10,12/POE/PDP (92/3/5 wt%) demonstrated a synergistic improvement in mechanical properties, with an elongation at break of 579% and a notch impact strength of 61.54 kJ/m2. This represents an approximately eightfold increase over the impact strength of unmodified PA10,12. Therefore, our work provides the potential of PDP as a compatibilizer to develop nylon composites with enhanced stiffness and toughness.
RESUMO
This research aims to highlight the importance of diverse forms of graphitic carbon nitride (g-C3N4) as strengthening elements in epoxy composites. It explores the influence of three different forms of g-C3N4 and their concentrations on the mechanical properties of the epoxy composites. Various characterization techniques, such as scanning electron microscopy (SEM), dynamic light scattering (DLS), thermogravimetric analysis (TGA), and Fourier-transform infrared spectroscopy (FTIR), were utilized to comprehend the effects of g-C3N4 morphology and particle size on the physical and chemical characteristics of epoxy resin. Mechanical properties, such as tensile strength, strain, modulus, and fracture toughness, were determined for the composite samples. SEM analysis was performed to examine crack morphology in samples with different reinforcements. Findings indicate that optimal mechanical properties were achieved with a 0.5 wt% bulk g-C3N4 filler, enhancing tensile strength by 14%. SEM micrographs of fracture surfaces revealed a transition from brittle to rough morphology, suggesting increased toughness in the composites. While the TGA results showed no significant impact on degradation temperature, dynamic mechanical analysis demonstrated a 17% increase in glass transition temperature. Furthermore, the improvement in thermal breakdown up to 600 °C was attributed to reinforced covalent bonds between carbon and nitrogen, supported by FTIR results.
RESUMO
OBJECTIVE: This study aims to explore the impact of family social support affects anxiety levels and mental toughness among nursing staff, and to identify the pathways of how mental toughness develops. METHODS: We selected 256 nursing staff from the Third People's Hospital of Chengdu using a convenience sampling method. Participants completed a questionnaire assessing family social support, anxiety level and mental toughness of the nursing staff. The questionnaires included the general information questionnaire, Perceived Social Support Scale (PSSS), Self-Rating Anxiety Scale (SAS), and the Connor-Davidson resilience scale (CD-RISC). Then, we analyzed the correlation between nursing staff' family social support, anxiety symptoms and mental toughness by using Pearson correlation. Finally, we analyzed the effect of family social support on mental toughness and anxiety levels by using linear regression, and analyzed the path of family social support and psychological toughness on anxiety symptoms by using structural equation modeling. RESULTS: We finally collected 246 valid questionnaires with a valid recovery rate of 96.09%. 116 (47.15%) nursing staff reported a moderate level of family social support, with a mean PSSS score of (58.98 ± 7.64). Anxiety risk was identified in 43.39% of participants, with a mean SAS score of 50.47 ± 10.96. In terms of mental toughness, 104 (42.28%) nursing staff exhibited a low level of mental toughness, and 116 (47.15%) demonstrated moderate level of mental toughness with CD-RISC score of (58.23 ± 10.12). Correlation analyses revealed a strong negative correlation between the family social support, mental toughness and their anxiety (r = -0.586, -0.516, respectively), and a strong positive correlation between family social support and mental toughness (r = 0.571). Regression analysis showed that family social support was a significant negative predictor for anxiety (ß = -0.841, t = -9.488), but a significant positive predictor for mental toughness (ß = 0.756, t = 11.669). Mediation analysis indicated that mental toughness mediated 26.28% of the relationship between family social support and anxiety levels. CONCLUSION: Family social support can significantly reduce anxiety levels in nursing staff directly, as well as indirectly by increasing mental toughness.
RESUMO
Plant fiber-reinforced polylactic acid (PLA) composites are extensively utilized in eco-friendly packaging, sports equipment, and various other applications due to their environmental benefits and cost-effectiveness. However, PLA suffers from brittleness and poor toughness, which restricts its use in scenarios demanding high toughness. To expand the application range of plant fiber-reinforced PLA-based composites and enhance their poor toughness, this study employed a two-step process involving wheat straw fiber (WF) to improve the interfacial compatibility between WF and PLA. Additionally, four elastomeric materials-poly (butylene adipate-co-terephthalate) (PBAT), poly (butylene succinate) (PBS), polycaprolactone (PCL), and polyhydroxyalkanoate (PHA)-were incorporated to achieve a mutual reactive interface enhancement and elastomeric toughening. The results demonstrated that Fe3+/TsWF/PLA/PBS exhibited a tensile strength, elongation at break, and impact strength of 34.01 MPa, 14.23 %, and 16.2 kJ/m2, respectively. These values represented a 2.4 %, 86.7 %, and 119 % increase compared to the unmodified composites. Scanning electron microscopy analysis revealed no fiber exposure in the cross-section, indicating excellent interfacial compatibility. Furthermore, X-ray diffraction and differential scanning calorimetry tests confirmed improvements in the crystalline properties of the composites. This work introduces a novel approach for preparing fiber-reinforced PLA-based composites with exceptional toughness and strength.
Assuntos
Elastômeros , Poliésteres , Resistência à Tração , Poliésteres/química , Elastômeros/química , Polímeros/química , Triticum/química , Teste de Materiais , Butileno Glicóis/químicaRESUMO
In this paper, we develop high aspect ratio nanofibrils from a polycaprolactone-based thermoplastic polyurethane (TPU) and evaluate their performance as a toughening agent. Poly(methyl methacrylate) (PMMA) was chosen as the matrix material because of its inherent brittleness and low resistance to sudden shocks and impact. We show that the addition of as little as 3 wt % of TPU nanofibrils with an average diameter of â¼98 nm and very high aspect ratio can significantly improve both the tensile toughness (â¼212%) and impact strength (â¼40%) of the chosen matrix (i.e., PMMA) without compromising its original strength, stiffness, and transparency. We compare the performance of TPU nanofibrils with TPU spherical particlesâthe form TPU typically manifests into when melt-mixed with an immiscible polymer. Our findings highlight that the structure of TPU plays a crucial role in determining the critical concentration of TPU needed for the brittle-ductile transition of the matrix. We also provide new and valuable insights into the unique interfacial interaction (i.e., formation of fibrillar bridges) observed between the PMMA matrix and TPU. We also show that the inclusion of 3 wt % of TPU nanofibrils can notably enhance resistance to creep deformation, even at temperatures close to the glass transition temperature of the matrix. Finally, we evaluate recyclability and demonstrate that the composite containing 3 wt % of TPU nanofibrils can be mechanically recycled without losing any properties. The proposed TPU nanofibrils can withstand repeated reprocessing at temperatures up to 190 °C due to their very high melting point and thermal stability. This presents the opportunity for them to be utilized not just with amorphous PMMA, but also with a range of other materials that can be processed at or below this temperature to remarkably improve their toughness without sacrificing strength and stiffness.