Chitosan Hydrogel Beads Supported with Ceria for Boron Removal.

In this study, a chitosan hydrogel supported with ceria (labelled Ce-CTS) was prepared by an encapsulation technique and used for the efficient removal of excess B(III) from aqueous solutions. The functionalisation of chitosan with Ce(IV) and the improvement in the adsorptive behaviour of the hydrogel were determined by SEM-EDS, FTIR, XRD, and inductively coupled plasma optical emission spectrometer (ICP-OES) analyses and discussed. The results demonstrate that Ce-CTS removes boric acid from aqueous solutions more efficiently than either cerium dioxide hydrate or raw chitosan beads, the precursors of the Ce-CTS biosorbent. The maximum adsorption capacity of 13.5 ± 0.9 mg/g was achieved at pH 7 after 24 h. The equilibrium data of boron adsorption on Ce-CTS fitted the Freundlich isotherm model, while the kinetic data followed the Elovich pseudo-second-order model, which indicated that the process was non-homogeneous. The dominant mechanism of removal was the reaction between boric acid molecules and hydroxyl groups bound to the ceria chelated by chitosan active centres. Due to its high efficiency in removing boron, good regeneration capacity and convenient form, Ce-CTS may be considered a promising biosorbent in water purification.

Preparation and evaluation of a reversed-phase/hydrophilic interaction/ion-exchange mixed-mode chromatographic stationary phase functionalized with dopamine-based dendrimers.

In this work, a novel dendritic stationary phase was synthesized by the repeated grafting of 1,4-butanediol diglycidyl ether (BDDE) and dopamine (DA) on the surface of silica for performing mixed-mode high-performance liquid chromatography (MHPLC). Elemental analysis (EA), thermogravimetric analysis (TGA) and Fourier transform infrared spectrometry (FT-IR) showed the successful preparation of the dendritic stationary phase. The prepared stationary phase showed the retention mechanisms of reversed-phase liquid chromatography (RPLC), hydrophilic interaction chromatography (HILIC) and ion-exchange chromatography (IEC) under different mobile phase conditions. In detail, alkylbenzenes, polycyclic aromatic hydrocarbons (PAHs) and hydrophobic positional isomers were separated successfully in the RPLC mode. The baseline separation of nucleobases, nucleosides and flavonoids was achieved under HILIC mode, respectively. Meanwhile, some acidic and basic analytes were used to evaluate the IEC mode. The effects of different chromatographic conditions, such as acetonitrile content, salt concentration and pH in the mobile phase, on the different chromatographic modes were also investigated. In addition, the application of the mixed-mode dendritic stationary phase was demonstrated by the analysis of traditional Chinese medicine (TCM), including Carthamus tinctorius L. and Abelmoschus manihot (Linn.) Medicus. Interestingly, the stationary phase also has the ability for the capture and separation of boric acids. These meaningful applications confirmed that the mixed-mode dendritic stationary phase can be potentially applied in the analysis of complex samples.

Efficient boron abstraction using honeycomb-like porous magnetic hybrids: Assessment of techno-economic recovery of boric acid.

Porous magnetic hybrids were synthesized and functionalized with glycidol to produce boron-selective adsorbent. The magnetic hybrid (MH) comparatively out-performed the existing expensive adsorbents. MH had a saturation magnetisation of 63.48 emu/g and average pore diameter ranging from meso to macropores. The magnetic hybrids showed excellent selectivity towards boron and resulted in 79-93% boron removal even in the presence of competing metal ions (Na+ and Cr2+). Experiments were performed in a column system, and breakthrough time was observed to increase with bed depths and decreased with flow rates. The batch experiments revealed that 60 min was enough to achieve equilibrium, and the level of boron sorption was 108.5 mg/g from a synthetic solution. Several adsorption-desorption cycles were performed using a simple acid-water treatment and evaluated using various kinetic models. The spent adsorbents could be separated easily from the mixture by an external magnetic field. The cost-benefit analysis was performed for the treatment of 72 m3/year boron effluent, including five years straight line depreciation charges of equipment. The net profit and standard percentage confirmed that the recovery process is economically feasible.

Fast isotopic separation of 10 B and 11 B boric acid by capillary zone electrophoresis.

Fast isotopic separation of 10 B and 11 B boric acid by CZE was demonstrated. The BGE contained 25 mM phenylalanine and 5 mM putrescine (рН 8.95). The running conditions were +25 kV at 20°C with indirect photometric detection at 210 nm. Baseline separation was achieved in less than 9 min. RSD of migration times and corrected peak areas were less than 0.5 and 3%, respectively (n = 5). Linearity was demonstrated in the range 0.2-2 mM for 11 B and 0.2-0.5 mM for 10 B.

A novel chemical oxo-precipitation (COP) process for efficient remediation of boron wastewater at room temperature.

Chemical oxo-precipitation (COP), which combines treatment with an oxidant and precipitation using metal salts, was developed for treating boron-containing water under milder conditions (room temperature, pH 10) than those of conventional coagulation processes. The concentration of boron compounds was 1000mg-BL(-1). They included boric acid (H3BO3) and perborate (NaBO3). Precipitation using calcium chloride eliminated 80% of the boron from the perborate solution, but was unable to treat boric acid. COP uses hydrogen peroxide (H2O2) to pretreat boric acid, substantially increasing the removal of boron from boric acid solution by chemical precipitation from less than 5% to 80%. Furthermore, of alkaline earth metals, barium ions are the most efficient precipitant, and can increase the 80% boron removal to 98.5% at [H2O2]/[B] and [Ba]/[B] molar ratios of 2 and 1, respectively. The residual boron in the end water of COP contained 15ppm-B: this value cannot be achieved using conventional coagulation processes.

Optimization of an adsorption process for tetrafluoroborate removal by zirconium (IV)-loaded orange waste gel from aqueous solution.

This investigation provides new insights into the effective removal of tetrafluoroborate (BF4-) by means of bio-sorption on waste generated in the orange juice industry. It was undertaken to evaluate the feasibility of zirconium (IV)-loaded saponified orange waste gel for BF4- removal from an aqueous solution. Batch adsorption experiments were carried out to study the influence of various factors such as pH, presence of competing anions, contact time, initial BF4- concentration and temperature on the adsorption of BF4-. The optimum BF4- removal was observed in the equilibrium pH region 2-3. The presence of coexisting anions showed no adverse effect on BF4- removal except SO4(2-). The equilibrium data at different temperatures were reasonably interpreted by the Langmuir adsorption isotherm and the maximum adsorption capacities were evaluated as 2.65, 3.28, 3.87 and 4.77 mmol g(-1) at 293, 298, 303 and 313 K, respectively. Thermodynamic parameters such as deltaGo, deltaHo and deltaSo indicated that the nature of BF4- adsorption is spontaneous and endothermic. The results obtained from this study demonstrate the potential usability of orange waste after juicing as a good BF4- selective adsorbent.

Substoichiometric isotope dilution mass spectrometry of boron by the ion-pair extraction with halogenated salicyl alcohol derivatives and a quaternary ammonium salt.

Novel salicyl alcohol derivatives (H(2)X(n)sal), 5-bromo-, 3,5-dibromo-, and 3,5-diiodosalicyl alcohol which were abbreviated to H(2)Brsal, H(2)Br(2)sal, and H(2)I(2)sal, respectively, were synthesized and used for the selective extraction of boric acid. Boric acid was extracted with each H(2)X(n)sal into chlorobenzene containing trioctylmethylammonium chloride (TOMACl) as an ion-pair complex, TOMA·B(X(n)sal)(2), at a different pH range. The extraction constant (K(ex)) of boric acid was determined by the equilibrium analyses including the formation of hydrogen-bonded complex of each H(2)X(n)sal with TOMACl in the organic phase. The K(ex) values obtained by salicyl alcohol (H(2)sal) and its derivatives were decreased in the order of H(2)I(2)sal ≥ H(2)Br(2)sal > H(2)Brsal > H(2)sal. The most powerful extractant, H(2)I(2)sal, was employed for the substoichiometric extraction of boric acid, which was extracted at pH 5 - 9 with a substoichiometric amount of TOMACl in the presence of an excess of H(2)I(2)sal. The present substoichiometric separation method combined with the stable isotope dilution analysis using inductively coupled plasma mass spectrometry (ICP-MS) could be successfully applied to the determination of boron in a reference material of high-analysis compound fertilizer (FAMIC-A-08) without any correction as to the isotopic abundance.

Synthesis of glucaminium-based ionic liquids and their application in the removal of boron from water.

A novel class of ionic liquids (ILs), exhibiting high selectivity towards boron species as well as the ability to phase separate from water, were synthesized from N-methyl-D-glucamine. The complexation of boric acid/borate with the ILs was confirmed using (11)B NMR.

Efficient removal of boron acid by N-methyl-D-glucamine functionalized silica-polyallylamine composites and its adsorption mechanism.

A novel boron adsorbent was fabricated by grafting a boric acid chelating group, i.e., N-methyl-D-glucamine, onto the hydrophilic silica-polyallylamine composites (SPC). The boron adsorbent was characterized by scanning electron microscopy (SEM) and TGA method. The adsorption experiment indicated a maximum boron load capacity of ca. 1.55 mmol g(-1). The high load capacity was attributed to specific chemical affinity and physical adsorption. Highly effective removal of boric acid from aqueous solution was observed for the adsorbent even in the synthetic seawater containing high concentration of foreign ions. Analysis of adsorption thermodynamic and kinetics revealed a spontaneous sorption process that is driven by enthalpy change and limited by chemical reaction. The exhausted adsorbent was regenerated for repeated use by treating with 3% HCl solution, followed by neutralizing with 3% NH(3)·H(2)O at ambient temperature. Only 7% capacity loss was observed after five continuous adsorption-regeneration cycles.

Adsorption and co-precipitation behavior of arsenate, chromate, selenate and boric acid with synthetic allophane-like materials.

Pollution caused by boric acid and toxic anions such as As(V), Cr(VI) and Se(VI) is hazardous to human health and environment. The sorption characteristics of these environmentally significant ionic species on allophane-like nanoparticles were investigated in order to determine whether allophane can reduce their mobility in the subsurface environment at circum-neutral pH condition. Solutions containing 100 or 150 mmol of AlCl(3)x6H(2)O were mixed to 100 mmol of Na(4)SiO(4) and the pH were adjusted to 6.4+/-0.3. The mineral suspensions were shaken for 1h and incubated at 80 degrees C for 5 days. Appropriate amounts of As, B, Cr and Se solutions were added separately during and after allophane precipitation. The results showed that As(V) and boric acid can be irreversibly fixed during co-precipitation in addition to surface adsorption. However, Cr(VI) and Se(VI) retention during and after allophane precipitation is mainly controlled by surface adsorption. The structurally fixed As(V) and boric acid were more resistant to release than those bound on the surface. The sorption characteristics of oxyanions and boric acid were also influenced by the final Si/Al molar ratio of allophane in which Al-rich allophane tend to have higher uptake capacity. The overall results of this study have demonstrated the role of allophane-like nanoparticles and the effect of its Si/Al ratio on As, B, Cr and Se transport processes in the subsurface environment.

Removal of tetrafluoroborate ion from aqueous solution using magnesium-aluminum oxide produced by the thermal decomposition of a hydrotalcite-like compound.

Magnesium-aluminum oxide (Mg-Al oxide) prepared by the thermal decomposition of a hydrotalcite-like compound was found to have potential for treating NaBF(4) wastewater. The Mg-Al oxide removed the BF(4)(-) and F(-) and H(3)BO(3) from the NaBF(4) solution. With increasing Mg-Al oxide quantity and time, the BF(4)(-) concentration decreased and the degree of BF(4)(-), F(-), and boron removal increased. The decrease in the BF(4)(-) concentration resulted from uptake by the Mg-Al oxide and not hydrolysis. The Mg-Al oxide took up F(-) from the solution preferentially. The Mg-Al oxide also converted the H(3)BO(3) in the aqueous solution into H(2)BO(3)(-), which it took up.

Removal of borate from tritiated gangliosides via the mannitoborate complex.

Purified gangliosides were radiolabeled by exposure to sodium boro [3H]hydride in the presence of palladium on barium sulfate. After centrifugation to remove the catalyst, borate was complexed with mannitol and the resulting mannitoborate complex and salts were removed by reversed phase chromatography. The labeled gangliosides were repurified by ion exchange and silica gel chromatographies. Radiopurity was determined by autoradiography of two-dimensional thin-layer chromatograms of the gangliosides. The method eliminates the need for extensive dialysis or repeated methanol evaporations to remove borate thus reducing time and the volume of labeled waste.

Colorimetric determination of boric acid in prawns, shrimp, and salted jelly fish by chelate extraction with 2-ethyl-1,3-hexanediol.

Borate was directly chelate-extracted from foods with 5% 2-ethyl-1,3-hexanediol (EHD) in n-hexane-n-butyl acetate mixture (8 + 2), from which borate was selectively transferred into 1% NaOH, since EHD-chelated boron did not react with curcumin to develop color. Finally, an aliquot of the alkaline solution was acidified with HCl and reacted with curcumin in a rotary evaporator. Color development was increased by heating for 8 min at 80 degrees C under reduced pressure of 16 mm Hg. Frozen shrimp and prawns (peeled and with shells) and salted jelly fish were analyzed by the proposed method. Results were compared with the contemporary official method of Japan based on curcumin reaction on an incinerated sample. Over 90% of the boric acid was recovered by the proposed method when samples were fortified with 20 ppm boric acid. Recoveries were superior to those of the official method especially for shrimp and prawns with shells and salted jelly fish. Detection limit of boric acid is 1 ppm. Moreover, the method requires only about 1 hr for analysis of one sample, making it suitable for routine analysis.