Resource utilization of MSWI fly ash supporting TiO2/BiOCl nanocomposite for enhanced photocatalytic degradation of sodium isopropyl xanthate: Mechanism and performance evaluation.

The removal of organic pollutants in water environments and the resource utilization of solid waste are two pressing issues around the world. Facing the increasing pollution induced by discharge of mining effluents containing sodium isopropyl xanthate (SIPX), in this work, municipal solid waste incineration fly ash (MSWI FA) was pretreated by hydrothermal method to produce stabilized FA, which was then innovatively used as support for the construction of FA/TiO2/BiOCl nanocomposite (FTB) with promoted photocatalytic activity under visible light and natural sunlight. When the content of FA was 20 wt% and the mass ratio of TiO2 to BiOCl was 4:6, a remarkable performance for the optimal FTB (20-FTB-2) was achieved. Characterizations demonstrated that TiO2 and BiOCl uniformly dispersed on FA contributing to high surface area and broad light adsorption of FTB, which exhibits excellent adsorption capacity and light response ability. Build in electric field formed in the interface of TiO2/BiOCl heterojunction revealed by density functional theory calculations accelerated the separation of photoinduced e- and h+, leading to high efficiency for SIPX degradation. The synergetic effect combined with adsorption and photocatalytic degradation endowed 20-FTB-2 superior SIPX removal efficiency over 99% within 30 min under visible light and natural sunlight irradiation. The photocatalytic degradation pathways of SIPX were determined through theoretical calculations and characterizations, and the toxic byproduct CS2 was effectively eliminated through oxidation of •O2-. For 20-FTB-2, reusability of photocatalyst was showed by cycle tests, also the concentrations of main heavy metals (Pb, Zn, Cu, Cr, and Cd) in the liquid phases released during photocatalyst preparation process (< 1 mg/L) and photodegradation process (< 8.5 µg/L) proved the satisfactory stability with low toxicity. This work proposed a novel strategy to develop efficient and stable support-based photocatalysts by utilizing MSWI FA and realize its resource utilization.

Solidification/stabilization and optimization of municipal solid waste incineration fly ash with aluminosilicate solid wastes.

Alkali-activation is an effective municipal solid waste incineration fly ash (MSWIFA) solidification/stabilization (S/S) technology. However, the characteristics of calcium-rich silica-poor aluminum phase in MSWIFA easily cause the structural instability and contamination of alkali activated MSWIFA S/S bodies. Therefore, the aluminosilicate solid wastes are used in this work to optimize the immobilization and structural properties. Results showed that incorporation of aluminosilicate solid wastes significantly improved the compressive strength and heavy metals pollution toxicity of MSWIFA S/S bodies. Compared to alkali activated MSWIFA, the compressive strength of S/S bodies with addition of coal fly ash, silica fume and granulated blast furnace slag improved by 31.0%, 47.6% and 50.8% when the curing time was 28 days, respectively. Leachability of Pb, Zn and Cd in these alkali activated MSWIFA S/S bodies was far below the threshold value specified in Standard GB16889. Aluminosilicate solid wastes provided abundant Si/Al structural units, and some new phases such as ettringite(AFt, 3CaO⋅Al2O3⋅3CaSO4⋅32H2O), calcium sulfoaluminate hydrate (3CaO⋅Al2O3⋅CaSO4⋅12H2O) and Friedel's salt (CaO⋅Al2O3⋅CaCl2⋅10H2O) can be detected in S/S matrix with aluminosilicate solid wastes, along comes increased the amount of the amorphous phases. Lower Ca/Si molar ratio tended to form the network structure gel similar to tobermorite with higher polymerization degree. Meanwhile, the silica tetrahedron of the gels changed from the oligomerization state like island to the hyperomerization state like chain, layer network or three-dimensional structure, and average molecular chain length increased. These findings provide theoretical basis for structural properties optimization and resource utilization of MSWIFA S/S matrices.

Analysis of composition characteristics and treatment techniques of municipal solid waste incineration fly ash in China.

The rapid development of the economy and society is causing an increase in the amount of municipal solid waste (MSW) produced by people's daily lives. With the strong support of the Chinese government, incineration power generation has steadily become the primary method of treating MSW, accounting for 79.86%. However, burning produces a significant amount of municipal solid waste incineration fly ash (MSWI-FA), which contains heavy metals, soluble chlorine salts, and dioxins. China's MSWI-FA yield increased by 8.23% annually to 7.80 million tons in 2022. Besides, the eastern region, especially the southeastern coastal region, has the highest yield of MSWI-FA. There are certain similarities in the chemical characteristics of MSWI-FA samples from Northeast, North, East, and South China. Zn and CaO have the largest amounts of metals and oxides, respectively. The Cl content is about 20 wt%. This study provides an overview of the techniques used in the thermal treatment method, solidification and stabilization, and separation and extraction of MSWI-FA and compares their benefits and drawbacks. In addition, the industrial applications and standard requirements of landfill treatment and resource utilization of MSWI-FA in China are analyzed. It is discovered that China's resource utilization of MSWI-FA is insufficient through the study on the fly ash disposal procedures at a few MSW incineration facilities located in the economically developed Guangdong Province and the traditional industrial city of Tianjin. Finally, the prospects for the disposal of MSWI-FA were discussed.

Mitigating ash-related alkali and heavy metals emissions in rotary kiln through oxygen-carrier-aided combustion of waste.

Rotary kiln (RK) incineration technology gains prominence in waste management, aiming to reduce pollution, recover energy, and minimize waste. Oxygen-carrier (OC)-aided incineration of waste in the RK demonstrates notable benefits by enhancing oxygen distribution uniformity and facilitating fuel conversion. However, the effects of OC on ash-related alkali and heavy metals during waste incineration in the RK remain unknown. In this study, manganese ore and ilmenite as OCs are introduced into RK during waste combustion, focusing on their effects on the bottom ashes and the behavior of alkali and heavy metals. Results show that manganese ore exhibits a decreasing reactivity due to oxygen depletion during the conversion from Mn2O3 to Mn3O4, while ilmenite maintains good reactivity due to sustained enrichment of Fe2O3 on the particles even after multiple cycles in RK. The porous structure on the surface of OCs particles verifies the cyclic reaction involving oxidation by air and reduction by fuel as OCs move between the active and passive layers of the bed. The porous OCs particles offer abundant adsorption sites for K from the gaseous phase, with surface-deposited K migrating into the particles and enhancing the OCs' capacity for K adsorption. Adding OCs promotes the formation of stable, less volatile compounds of heavy metals (As, Cr, Pb, and Zn) and enhances their retention in bottom ash while ensuring the leaching toxicity remains below Chinese national standard limits. This study enhances the understanding of OCs in incineration, guiding vital references for waste management practices and environmental sustainability.

Lanthanum-modified tobermorite synthesized from fly ash for efficient phosphate removal.

Phosphate removal from water by lanthanum-modified tobermorite synthesized from fly ash (LTFA) with different lanthanum concentrations was studied. LTFA samples were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and Brunauer‒Emmett‒Teller specific surface area analysis. The results showed that the LTFA samples were mainly composed of mesoporous tobermorite-11 Å, and LTFA1 with a lanthanum concentration of 0.15 M had a high specific surface area (83.82 m2/g) and pore volume (0.6778 cm3/g). The phosphate adsorption capacities of LTFA samples were highest at pH 3 and gradually decreased with increasing pH. The phosphate adsorption kinetics data on LTFA samples were most accurately described by the Elovich model. The adsorption isotherms were in the strongest agreement with the Temkin model, and LTFA1 showed the highest phosphate adsorption capacity (282.51 mg P/g), which was higher than that of most other lanthanum-modified adsorbents. LTFA1 presented highly selective adsorption of phosphate with other coexisting ions (HCO3-, Cl-, SO42-, and NO3-). In addition, phosphate was adsorbed onto LTFA samples by forming inner-sphere phosphate complexes and amorphous lanthanum phosphate. This study provides technical support for development of efficient fly ash-based phosphate adsorbents.

Fly ash treatment via conventional and microwave-assisted organic acid leaching: kinetics and life cycle assessment.

Heedless disposal of oil-based fly ash contributes to the contamination of the air, water, and soil. Acid leaching of industrial solid wastes is recognized as a versatile, cost-effective, and environmentally friendly solid waste treatment approach. The present study investigated the viability of conventional leaching (CL) and microwave-assisted leaching (MAL) of predominant heavy metals from Mazut-burnt fly ash. For this purpose, the practicality of four organic acids with various specifications (ascorbic, gluconic, citric, and oxalic acids) on the dissolution efficiency of fly ash components was examined. Utilization of oxalic acid led to achieving full V recovery, complete Fe removal, and Ni enrichment in the residue in both CL and MAL setups. The Ni content of the sample was enriched from 6% in the calcinated sample to 23.7% in the oxalic acid leaching residue. Using citric acid resulted in the co-extraction of V, Ni, and Fe with nearly 70% V, 50% Ni, and 89% Fe dissolved in CL. The dissolution efficiencies were slightly lower in MAL. Oxalic acid was selected as the most promising organic acid reagent for fly ash treatment, so its CL kinetics was studied and defined by the shrinking particle model. The model showed that the controlling steps in the leaching of V differ over time, changing from a chemical reaction before 60 min to fluid film diffusion or mixing afterward. The kinetic study proved MAL as an effective technique in overcoming the leaching kinetic barriers. A life cycle assessment study was conducted to determine the environmental impacts of the proposed process. Accordingly, the MAL using oxalic acid was the most environmentally friendly process among the studied ones, and the utilization of microwaves leads to the reduction of the leaching processes' environmental impacts by decreasing the processing time.

A systematic comparison of salt removal efficiency in washing treatment by using fly ashes from 13 MSWI plants in China.

Municipal solid waste incineration (MSWI) fly ash contains large amounts of Ca, Si, and other elements, giving it the potential to be used as a raw material for cement production. However, fly ash often contains a high content of salts, which greatly limits its blending ratio during cement production. These salts are commonly removed via water washing, but this process is affected by the nature and characteristics of fly ash. To clarify the influence of the ash characteristics on salt removal, a total of 60 fly ash samples from 13 incineration plants were collected, characterized, and washed. The ash characterization and cluster analysis showed that the incinerator type and flue gas purification technology/process significantly influenced the ash characteristics. Washing removed a high percentage of salts from fly ash, but the removal efficiencies varied significantly from each other, with the chlorine removal efficiency ranging from 73.76% to 96.48%, while the sulfate removal efficiency ranged from 6.92% to 51.47%. Significance analysis further revealed that the salt removal efficiency varied not only between the ash samples from different incinerators, but also between samples collected at different times from the same incinerator. The high variance of the 60 ash samples during salt removal was primarily ascribed to their different mineralogical and chemical characteristics. Mineralogical analysis of the raw and washed ash samples showed that the mineralogical forms and proportion of these salts in each ash sample greatly influenced their removal. The presence of less-soluble and insoluble chloride salts (e.g., CaClOH, Ca2Al(OH)6(H2O)2Cl etc.) in fly ash significantly affected the chlorine removal efficiency. This study also found that Fe, Mn, and Al in fly ash were negatively correlated with the dechlorination efficiency of fly ash. In summary, the different physical and chemical properties of fly ash caused great discrepancies in salt removal. Consequently, it is suggested to consider the potential impact of the ash source and ash generation time on salt removal to ensure a reliable treatment efficiency for engineering applications.

Ni-FeOx synergy induced by metal-support interaction on Ni-impregnated incineration bottom ash for effective tar reforming.

The incineration bottom ash (IBA) was impregnated with nickel to catalyze toluene (tar surrogate) steam reforming. A toluene conversion of >80 % was achieved at 800℃ without activity decay in a 100-h test for 15 %Ni/IBA. An activation stage was observed for Ni/IBA catalysts in the initial 50 âˆ¼ 400 min under different reaction conditions. A series of experiments and characterizations were performed to explore the possible mechanisms for the activation. It was found that the iron species in IBA gradually migrated to the catalyst surface and formed a Ni-FeOx complex owing to the metal-support interaction. The synergy of Ni-FeOx played an important role in improving the activity of Ni/IBA due to the enhanced lattice oxygen activity. Additionally, Ni/IBA catalysts showed a much lower coke deposition rate than Ni/Al2O3 (1.12 vs. 3.45 mg-C/gcat∙h) because of the variable states of FeOx and the abundant basic sites caused by the alkali and alkaline earth metals contained in IBA.

Optimizing MSW incineration bottom ash reuse: A study on treated wastewater washing and leaching control.

The current study introduces an innovative methodology by utilizing treated wastewater (TWW) from an effluent treatment plant as a washing agent to enhance the characteristics of incineration bottom ash (IBA). This approach addresses sustainability concerns and promotes the circular economy by reusing wastewater generated in municipal solid waste incineration facilities. Previous research has underscored the challenges of open IBA reuse due to elevated leaching of chlorides, sulfates, and trace metal(loid)s. Thus, the experimental setup explores various combinations of washing, with or without screening, to optimize the properties of soil-like material (SLM < 4.75 mm) and overall material (OM < 31.5 mm) fractions of IBA for unrestricted applications. Batch leaching tests were conducted on treated samples, and leaching characteristics were evaluated in accordance with regulatory standards, primarily the Dutch standard for unrestricted IBA reuse. The findings reveal that washing in isolation proves insufficient to enhance IBA properties; however, washing followed by screening, specifically for removing fines (<0.15 mm), proves effective in reducing contamination. The study identifies that multiple steps of washing and screening (with recirculation) process render OM and SLM fractions suitable for unrestricted reuse with a cumulative liquid-to-solid ratio of 6 L/kg and a total washing time of 15 min. The multi-step treatment was found effective in reducing sulfate contamination by 65-74 % and chloride contamination by 83-89 % in IBA fractions. This approach offers a promising solution for overcoming the limitations associated with IBA leaching, thereby promoting sustainable waste reuse practices.

Environmental performance of unfired bricks produced from co-disposal of mine tailings and municipal solid waste incineration fly ash based on comprehensive leaching tests.

The potential leaching of heavy metals is a crucial concern for construction materials produced from solidification/stabilization (S/S) treatment of wastes. This study comprehensively evaluated the leaching characteristics of heavy metals from the unfired bricks produced from co-disposal of Pb-Zn mine tailings and municipal solid waste incineration fly ash using batch, sequential, and semi-dynamic leaching tests. The results show that S/S treatment drastically reduced the leachability of heavy metals from the unfired bricks through lowering their distribution in the acid-soluble fraction. The effective diffusion coefficients of heavy metals within unfired bricks were all below 1.55 × 10-13 cm2/s, which is indicative of low mobility in the environment. The release of heavy metals from the unfired bricks was primarily governed by diffusion and dissolution. Slaking treatment of fly ash significantly reduced the leaching of heavy metals from the unfired bricks due to their improved structural integrity and compactness, which minimizes the surface area in the solid matrix accessible by the leaching medium. The leachability indices of heavy metals within the unfired bricks ranged from 13.12 to 18.10, suggesting that they are suitable for "controlled utilization" in specific scenarios. Compared to untreated mine tailings, converting them into unfired bricks could reduce the releases of heavy metals by several to hundreds of folds. These findings demonstrate that S/S can be an effective and sustainable strategy for co-disposal of mining tailings and incineration fly ash to produce construction materials with sound long-term environmental performance.

Effect of long-term dry-wet circulations on the Solidification/stabilization of Municipal solid waste incineration fly ash using a novel cementitious material.

Solidification/stabilization (S/S) is a typical technique to immobilize toxic heavy metals in Municipal solid waste incineration fly ash (MSWI FA). This study utilized blast furnace slag, steel slag, desulfurization gypsum, and phosphoric acid sludge to develop a novel metallurgical slag based cementing material (MSCM). Its S/S effects of MSWI FA and long-term S/S effectiveness under dry-wet circulations (DWC) were evaluated and compared with ordinary Portland cement (OPC). The MSCM-FA block with 25 wt.% MSCM content achieved 28-day compressive strength of 9.38 MPa, indicating its high hydration reactivity. The leaching concentrations of Pb, Zn and Cd were just 51.4, 1895.8 and 36.1 µg/L, respectively, well below the limit standard of Municipal solid wastes in China (GB 16889-2008). After 30 times' DWC, leaching concentrations of Pb, Zn and Cd for MSCM-FA blocks increased up to 130.7, 9107.4 and 156.8 µg/L, respectively, but considerably lower than those for OPC-FA blocks (689, 11,870.6 and 185.2 µg/L, respectively). The XRD and chemical speciation analysis revealed the desorption of Pb, Zn and Cd attached to surface of C-S-H crystalline structure during the DWC. The XPS and SEM-EDS analysis confirmed the formation of Pb-O-Si and Zn-O-Si bonds via isomorphous replacement of C-A-S-H in binder-FA blocks. Ettringite crystalline structure in OPC-FA block was severely destructed during the DWC, resulting in the reduced contents of PbSO4 and CaZn2Si2O7·H2O and the higher leachability of Pb2+ and Zn2+.

Characterization of novel polysulfide polymer coated fly ash and its application in mitigating diffusion of contaminants.

Fly ash consists of a considerable amount of hazardous elements with high mobility, posing substantial environmental risks during storage in surface impoundments and landfills. This hinders its efficient reuse in construction or material industries. To enhance the versatility of fly ash applications, a novel surface modification technique, termed SuMo, has been developed to create a hydrophobic polysulfide polymer coating on the surface of fly ash particles. The physicochemical properties of SuMo fly ash samples were examined using atomic force microscopy (AFM), environmental scanning electron microscopy (ESEM), thermal gravimetric analysis (TGA), Fourier Transform Infrared spectroscopy (FTIR), and leaching of hazardous elements was tested under practical environmental conditions (pH 4-12) based on the EPA's leaching environmental assessment framework (LEAF). The successful coating of polysulfide polymer on fly ash surface was verified through an increased percentage of C, S, and O in elemental mapping, coupled with the identification of S-O, CO, and C-H functional groups consistent with the chemical structure of polysulfide polymer. While the SuMo fly ash particles maintained their spherical shape, they exhibited increased surface roughness, robust hydrophobicity, and thermal stability up to 250 °C. Notably, owing to the coating's resilience against water leaching, the SuMo fly ash demonstrated a substantial reduction (up to 60-fold) in leachate concentrations of multiple concerning elements, including B, Be, Ba, Mn, Zn, As, Cr, Hg, etc., under various pH conditions compared to the uncoated fly ash. Furthermore, the polysulphide polymer coating effectively prevented Hg volatilization from fly ash below 163 °C. This study highlights the efficacy of the developed polysulfide polymer coating in mitigating the diffusion of hazardous elements from fly ash, thereby enhancing its potential reutilization in material, construction, and agriculture industries.

Designing low-carbon fly ash based geopolymer with red mud and blast furnace slag wastes: Performance, microstructure and mechanism.

In order to tackle the environmental problems induced by Portland cement production and industrial solid wastes landfilling, this study aims to develop novel ternary cementless fly ash-based geopolymer by recycling red mud and blast furnace slag industrial solid wastes. The fresh-state properties, mechanical strength, water permeability, phase assemblage and microstructure were systematically investigated to evaluate the performance variation and reveal the hydration mechanism for geopolymers with different mixing proportions. The results showed that a higher slag content or a lower red mud content could result in the higher fluidity and shorter setting time for fresh mixture. The existence of slag promoted the transformation of N-A-S-H to C-A-S-H gel, which contributed to higher compressive strength and better resistance to water penetration. However, an excessive incorporation of 30% red mud may impede the generation of N-A-S-H gel and form more flocculent-like loose hydrates, thus to mildly degrade the mechanical strength and anti-permeability. The synergetic utilization of red much and blast furnace slag in fly ash-based geopolymer led to much less CO2 emission compared with the condition that red much or slag was singly added, which demonstrated prominent environmental advantages for such kind of ternary cementless geopolymer with equivalent mechanical strength.

From waste to catalyst: Growth mechanisms of ZSM-5 zeolite from coal fly ash & rice husk ash and its performance as catalyst for tetracycline degradation in fenton-like oxidation.

Coal fly ash (CFA), an industrial solid waste, can be utilized to synthesize Zeolite Socony Mobil-5 (ZSM-5) by incorporating an external silica source. In this study, a series of ZSM-5 zeolites were synthesized using rice husk ash (RHA) as the primary silica source and CFA as the primary aluminum source under controlled hydrothermal reaction conditions, and the growth mechanism of ZSM-5 was investigated. The process of ZSM-5 growth was featured by the transformation of hyperpoly silico-aluminate in CFA and RHA into monomers. These monomers formed crystal nuclei connected in a five-membered ring structure under the influence of Tetrapropyl ammonium hydroxide (TPAOH). The surplus monomeric silica-aluminate grew on the nucleus surface due to the addition of the silica source within RHA (RHA-SiO2), ultimately resulting in the development of ZSM-5 zeolite. Characterization results demonstrated that RHA-SiO2 exhibited favorable physical and chemical properties during the ZSM-5 synthesis, with a crystallinity of 99.03%, a specific surface area of 321.19 m2/g, a weight loss of only 3.06% at 800 °C and a total acidity of 0.65 mmol/g. To evaluate the catalytic performance of ZSM-5, Fe/Cu-modified ZSM-5 was developed and used as the catalyst for the degradation of tetracycline (TC) in Fenton-like oxidation. The results indicated that Fe/Cu-ZSM-5 exhibited excellent activity and stability as the catalyst for TC degradation and mineralization. The maximum TC degradation rate reached 99.02% in 10 min and the TOC removal could be up to 69.32% in 2 h. Characterization results indicated that the Fe/Cu ions redox cycle accelerated the generation of active species (1O2 and ˙OH) in Fenton-like systems. The ZSM-5 zeolite synthesized from solid waste demonstrated superb stability and catalytic activity, leading to the effective removal of TC. Since real wastewater generally contains various pollutants, future research efforts should focused on multi-pollutant treatment.

Preparation of geopolymer based on municipal solid waste incineration fly ash-phosphorus slag and its function for solidification of heavy metals.

Municipal solid waste incineration fly ash (MSWIFA) contains potential contaminants and needs to be efficiently solidified/stablized and so should be managed properly. To achieve this goal, alkali-activated MSWIFA and phosphorus slag (PS) based geopolymer solidified bodies were investigated. Therefore, the mechanical properties of the solidified body, heavy metal leaching characteristics, heavy metal chemical forms, and heavy metal solidification/stabilization mechanisms were also analyzed. The results show that: The addition of an appropriate amount of PS can promote the strength development of a solidified body. When the mass ratio of MSWIFA to PS is 7:3, the strength of the solidified body reaches 22.8 MPa at 90d curing age, which is 5.3 times higher than that of the unmodified material. The MSWIFA/PS immobilized Zn 99.9 %, Pb 99.4 % and Cd 99.8 % in 60 day leaching tests. Meanwhile, PS can significantly increase the proportion of chemically stabilized forms of heavy metals in the solidified body. PS affects on the hydration process of the solidified body. When the mass fraction of PS doping was 30 %, the main hydration products of the solidified body were calcium silicate hydrate (C-S-H) and calcium alumina (AFt). When the mass fraction of PS is 50 %, the main hydration products are calcium aluminosilicate hydrate (C-A-S-H), sodium aluminosilicate hydrate (N-A-S-H), and AFt. These hydration products have good solidification effects on heavy metals. Therefore, it can be concluded that the MSWIFA/PS solidified body is an environmentally friendly and efficient binder.

Wood fly ash and blast furnace slag management by alkali-activation: Trace elements solidification and composite application.

Wood and biomass are burned in many industries as a sustainable energy source. The large quantities of fly ash produced must be landfilled, leading to environmental concerns. Precipitator wood fly ash (PFA) and ground granulated blast furnace slag (BFS) have been used in this study to prepare alkali-activated composites to manage and recycle the fly ash. After an essential characterization, the influence of parameters such as PFA and BFS content, alkaline activator content (silica moduli of 0, 0.82, 1.32), curing method, and curing duration on the mechanical, chemical, and microstructural properties of the samples have been studied through compressive strength, density, FTIR, and SEM-EDS investigations. The environmental safety and influence of polycondensation on heavy metal stabilization have been examined through ICP-MS. The results prove that oven and hydrothermal curing obtain the early age strength. Despite the variations of strength with duration and type of curing, the compressive strength of samples after 28 days of curing tends to close values for a constant PFA/BFS ratio, due to which the need for energy-intensive curing methods is addressed. ICP-MS shows that the composites can suitably solidify As, Cd, Ba, Cr, Pb, Mo, Se, Hg, Sr, Cu, and Zn. On the other hand, the composites were almost incapable of stabilizing Co and V. Unlike the case for mechanical properties; higher PFA content favours hazardous metal stabilization through polycondensation.

Preparation and characterization of P-type zeolite for adsorption of Cr3+, Ni2+, and Co2.

Acid-washed coal fly ash (AW-CFA) was subjected to wet grinding activation followed by hydrothermal crystallization to synthesize P zeolite (FAZ-P). The FAZ-P obtained at 120 °C for 24 h exhibited a maximum relative crystallinity of 93.15% and was employed for the adsorption of Cr3+, Ni2+, and Co2+ from aqueous solutions. The zeolitization of coal fly ash (CFA) leads to an increase in specific surface area to 44.00 m2/g, resulting in the formation of nano-sized P zeolite crystals with uniformly narrow fissures and sizes within the range of 10-30 nm. Adsorption experimental results indicate that FAZ-P exhibits maximum adsorption capacities of 49.03 mg/g for Cr3+, 22.20 mg/g for Ni2+, and 27.25 mg/g for Co2+. The adsorption equilibrium data for both mixed and single-metal ion solutions conform to the Langmuir model, with the affinity sequence for heavy metal ions being Cr3+ > Co2+ > Ni2+. The pseudo-first-order and pseudo-second-order kinetic models effectively described the adsorption behavior of Cr3+, Ni2+, and Co2+. Increasing the initial pH value of the solution significantly enhanced the adsorption capacity of the adsorbent for heavy metal ions. The removal mechanism of metal ions involves both adsorption and ion exchange processes. The thermodynamic parameters indicated that the adsorption process was spontaneous and endothermic.

Migration and transformation of Pb, Cu, and Zn during co-combustion of high-chlorine-alkaline coal and Si/Al dominated coal.

Shaerhu (SEH) coal is abundant in Xinjiang, China. The utilization of SEH suffers from severe ash deposition, slagging, and fouling problems due to its high-chlorine-alkaline characteristics. The co-combustion of high-alkaline coal and other type coals containing high Si/Al oxides has been proven to be a simple and effective method that will alleviate ash-related problems, but the risk of heavy metals (HMs) contamination in this process is nonnegligible. Hence, the volatilization rates and chemical speciation of Pb, Cu, and Zn in co-combusting SEH and a high Si/Al oxides coal, i.e., Yuanbaoshan (YBS) coal were investigated in this study. The results showed that the addition of SEH increased the volatilization rates of Pb, Cu, and Zn during the co-combustion at 800°C from 23.70%, 23.97%, and 34.98% to 82.31%, 30.01%, and 44.03%, respectively, and promoted the extractable state of Cu and Zn. In addition, the interaction between SEH and YBS inhibited the formation of the Pb residue state. SEM-EDS mapping results showed that compared to Zn and Cu, the signal intensity of Pb was extremely weak in regions where some of the Si and Al signal distributions overlap. The DFT results indicated that the O atoms of the metakaolin (Al2O3⋅2SiO2) (001) surface were better bound to the Zn and Cu than Pb atoms after adsorption of the chlorinated HMs. These results contribute to a better understanding of the effects of high-alkaline coal blending combustion on Pb, Cu, and Zn migration and transformation.

Use of municipal solid waste incineration (MSWI) bottom ash as a permeable subgrade material: An experimental and mechanism study.

As a traditional method of waste treatment, municipal solid waste incineration (MSWI) has become one of the main methods of urban waste treatment. However, as a byproduct of MSWI, a large amount of MSWI bottom ash is not reused in current practice. This study innovatively posits MSWI bottom ash as an eco-friendly adsorbent rather than a pollutant, exploring its potential application as a permeable subgrade material. The results reveal that MSWI bottom ash exhibits promising properties to serve as a permeable subgrade material to achieve the permeability and improve the sustainability for subgrade. Due to the arrangement of its particles, it shows excellent performance in shear strength and permeability, which are comparable to or surpass those of sandy soils. The average pore width of 14.200 nm allows heavy metal substances to be encapsulated within the matrix, significantly reducing their leachability, thereby aligning with environmental friendliness standards. Its adsorption capacity is about 6.60 mg/g, and the adsorption capacity per volume is 3.66 times and 2.04 times that of fly ash and clay, respectively. The mechanism analysis shows that the adsorption process is monolayer heterogeneous adsorption. This paper presents a novel perspective on reusing MSWI bottom ash and provides evidence supporting its effective utilization as a permeable subgrade material, offering substantial environmental benefits through enhanced adsorption ability.Implications: Municipal solid waste incineration (MSWI) is a common method for municipal solid waste treatment, while the MSWI bottom ash is often not reused. This paper explored the explores the feasibility of using MSWI bottom ash as a permeable road base material. The results show that the particle arrangement enables excellent shear strength and permeability, comparable to sandy soil. It meets safety requirements for the leaching of heavy metals and acts as an adsorbent for pollutants leaching from permeable pavements. Furthermore, the mechanisms underlying these behaviors of MSWI were confirmed by microstructural and mineralogical analyses. These indicate that MSWI bottom ash has great potential as a permeable road base material. This paper provides a clear understanding of the physical, mechanical and environmental properties of MSWI bottom ash, which can promote its reuse in practice.

Characterization and stabilization of incineration fly ash from a new multi-source hazardous waste co-disposal system: field-scale study on solidification and stabilization.

The multi-source hazardous waste co-disposal system, a recent innovation in the industry, offers an efficient approach for hazardous waste disposal. The incineration fly ash (HFA) produced by this system exhibits characteristics distinct from those of typical incineration fly ash, necessitating the use of adjusted disposal methods. This study examined the physicochemical properties, heavy metal content, heavy metal leaching concentration, and dioxin content of HFA generated by the new co-disposal system and compared them with those of conventional municipal waste incineration fly ash. This study investigated the solidification and stabilization of HFA disposal using the organic agent sodium diethyl dithiocarbamate combined with cement on a field scale. The findings revealed significant differences in the structure, composition, and dioxin content of HFA and FA; HFA contained substantially lower levels of dioxins than FA did. Concerning the heavy metal content and leaching; HFA exhibited an unusually high concentration of zinc, surpassing the permitted emission limits, making zinc content a critical consideration in HFA disposal. After stabilization and disposal, the heavy metal leaching and dioxin content of HFA can meet landfill disposal emission standards when a 1% concentration of 10% sodium diethyldithiocarbamate (DDTC) and 150% silicate cement were employed. These results offer valuable insights into the disposal of fly ash resulting from incineration of mixed hazardous waste.