Insights on the role of blocking agent on the properties of the lipase from Thermomyces lanuginosus immobilized on heterofunctional support for hydroesterification reactions.

Here, we report a study of the effect of the blocking agent on the properties of the lipase from Thermomyces lanuginosus (TLL) immobilized on a heterofunctional support (Purolite C18-ethylnediamina (EDA)- vinyl sulfone (VS)-TLL-blocking agent) in different reactions. The performance of the biocatalysts was compared to those immobilized on standard hydrophobic support (Purolite C18-TLL) and the commercial one (TLL-IM). The nature of the blocking agent (Cys, Gly and Asp) altered the enzyme features. TLL-IM always gave a comparatively worse performance, with its specificity for the oil being very different to the Purolite biocatalysts. Under optimized conditions, Purolite C18-TLL yielded 97 % of hydrolysis conversion after 4 h using a water/waste cooking soybean oil (WCSO) mass ratio of 4.3, biocatalyst load of 6.5 wt% and a temperature of 44.2 °C (without buffer or emulsification agent). In esterification reactions of the purified free fatty acids (FFAs) obtained from WCSO, the best TLL biocatalysts depended on the utilized alcohol: linear amyl alcohol was preferred by Purolite C18-TLL and Purolite C18-EDA-VS-TLL-Gly, while higher activity was achieved utilizing isoamyl alcohol as nucleophile by Purolite C18-EDA-VS-TLL-Cys, Purolite C18-EDA-VS-TLL-Asp and IM-TLL as catalysts. All the results indicate the influence of the blocking step on the final biocatalyst features.

Preparation of a heterogeneous biocatalyst through Thermomyces lanuginosus lipase immobilization on pore-expanded SBA-15.

Heterogeneous biocatalysts were prepared by adsorbing T. lanuginosus lipase (TLL) onto uncalcined (SBAUC-TLL) and calcined (SBAC-TLL) SBA-15, using ammonium fluoride as a pore expander to facilitate TLL immobilization. At an enzyme load of 1 mg/g, high immobilization yields (>90 %) and recovered activities (>80 % for SBAUC-TLL and 70 % for SBAC-TLL) were achieved. When increasing the enzyme load to 5 mg/g, the immobilization yield of SBAUC-TLL was 80 %, and the recovered activity was 50 %, while SBAC-TLL had a yield of 100 % and a recovered activity of 36 %. Crosslinking with glutaraldehyde (GA) was conducted to improve stability (SBAUC-TLL-GA and SBAC-TLL-GA). Although SBAC-TLL-GA lost 25 % of initial activity after GA modifications, it exhibited the highest thermal (t1/2 = 5.7 h at 65 °C), when compared to SBAC-TLL (t1/2 = 12 min) and the soluble enzyme (t1/2 = 36 min), and operational stability (retained 100 % activity after 5 cycles). Both biocatalysts presented high storage stability since they retained 100 % of initial activity for 30 days. These results highlight SBA-15's potential as an enzyme support and the protocol's efficacy in enhancing stability, with implications for industrial applications in the food, chemical, and pharmaceutical sectors.

Recombinant cellobiose dehydrogenase from Thermothelomyces thermophilus: Its functional characterization and applicability in cellobionic acid production.

The fungus Thermothelomyces thermophilus is a thermotolerant microorganism that has been explored as a reservoir for enzymes (hydrolytic enzymes and oxidoreductases). The functional analysis of a recombinant cellobiose dehydrogenase (MtCDHB) from T. thermophilus demonstrated a thermophilic behavior, an optimal pH in alkaline conditions for inter-domain electron transfer, and catalytic activity on cellooligosaccharides with different degree of polymerization. Its applicability was evaluated to the sustainable production of cellobionic acid (CBA), a potential pharmaceutical and cosmetic ingredient rarely commercialized. Dissolving pulp was used as a disaccharide source for MtCDHB. Initially, recombinant exoglucanases (MtCBHI and MtCBHII) from T. thermophilus hydrolyzed the dissolving pulp, resulting in 87% cellobiose yield, which was subsequently converted into CBA by MtCDHB, achieving a 66% CBA yield after 24 h. These findings highlight the potential of MtCDHB as a novel approach to obtaining CBA through the bioconversion of a plant-based source.

Application of Thermomyces lanuginosus polygalacturonase produced in Komagataella phaffii in biomass hydrolysis and textile bioscouring.

In this work, the polygalacturonase (TL-PG1) from the thermophilic fungus Thermomyces lanuginosus was heterologously produced for the first time in the yeast Komagataella phaffii. The TL-PG1 was successfully expressed under the control of the AOX1 promoter and sequentially purified by His-tag affinity. The purified recombinant pectinase exhibited an activity of 462.6 U/mL toward polygalacturonic acid under optimal conditions (pH 6 and 55 ˚C) with a 2.83 mg/mL and 0.063 µmol/minute for Km and Vmax, respectively. When used as supplementation for biomass hydrolysis, TL-PG1 demonstrated synergy with the enzymatic cocktail Ctec3 to depolymerize orange citrus pulp, releasing 1.43 mg/mL of reducing sugar. In addition, TL-PG1 exhibited efficiency in fabric bioscouring, showing potential usage in the textile industry. Applying a protein dosage of 7 mg/mL, the time for the fabric to absorb water was 19.77 seconds (ten times faster than the control). Adding the surfactant Triton to the treatment allowed the reduction of the enzyme dosage by 50% and the water absorption time to 6.38 seconds. Altogether, this work describes a new versatile polygalacturonase from T. lanuginosus with the potential to be employed in the hydrolysis of lignocellulosic biomass and bioscouring.

Enzyme-support interactions and inactivation conditions determine Thermomyces lanuginosus lipase inactivation pathways: Functional and florescence studies.

Lipase from Thermomyces lanuginosus (TLL) has been covalently immobilized on heterofunctional octyl-vinyl agarose. That way, the covalently immobilized enzymes will have identical orientation. Then, it has blocked using hexyl amine (HEX), ethylenediamine (EDA), Gly and Asp. The initial activity/stability of the different biocatalysts was very different, being the most stable the biocatalyst blocked with Gly. These biocatalysts had been utilized to analyze if the enzyme activity could decrease differently along thermal inactivation courses depending on the utilized substrate (that is, if the enzyme specificity was altered during its inactivation using 4 different substrates to determine the activity), and if this can be altered by the nature of the blocking agent and the inactivation conditions (we use pH 5, 7 and 9). Results show great changes in the enzyme specificity during inactivation (e.g., activity versus triacetin was much more quickly lost than versus the other substrates), and how this was modulated by the immobilization protocol and inactivation conditions. The difference in the changes induced by immobilization and inactivation were confirmed by fluorescence studies. That is, the functional and structural analysis of partially inactivated immobilized enzyme showed that their inactivation pathway is strongly depended on the support features and inactivation conditions.

Computational and experimental analysis on the preferential selectivity of lipases for triglycerides in Licuri oil.

In the present study, we demonstrated the use of molecular docking as an efficient in silico screening tool for lipase-triglyceride interactions. Computational simulations using the crystal structures from Burkholderia cepacia lipase (BCL), Thermomyces lanuginosus lipase (TLL), and pancreatic porcine lipase (PPL) were performed to elucidate the catalytic behavior with the majority triglycerides present in Licuri oil, as follows: caprilyl-dilauryl-glycerol (CyLaLa), capryl-dilauryl-glycerol (CaLaLa), capryl-lauryl-myristoyl-glycerol (CaLaM), and dilauryl-myristoyl-glycerol (LaLaM). The computational simulation results showed that BCL has the potential to preferentially catalyze the major triglycerides present in Licuri oil, demonstrating that CyLaLa, (≈25.75% oil composition) interacts directly with two of the three amino acid residues in its catalytic triad (Ser87 and His286) with the lowest energy (-5.9 kcal/mol), while other triglycerides (CaLaLa, CaLaM, and LaLaM) interact with only one amino acid (His286). In one hard, TLL showed a preference for catalyzing the triglyceride CaLaLa also interacting with His286 residue, but, achieving higher binding energies (-5.3 kcal/mol) than found in BCL (-5.7 kcal/mol). On the other hand, PPL prefers to catalyze only with LaLaM triglyceride by His264 residue interaction. When comparing the computational simulations with the experimental results, it was possible to understand how BCL and TLL display more stable binding with the majority triglycerides present in the Licuri oil, achieving conversions of 50.86 and 49.01%, respectively. These results indicate the production of fatty acid concentrates from Licuri oil with high lauric acid content. Meanwhile, this study also demonstrates the application of molecular docking as an important tool for lipase screening to reach a more sustainable production of fatty acid concentrates from vegetable oils.

Agroindustrial Wastes as a Support for the Immobilization of Lipase from Thermomyces lanuginosus: Synthesis of Hexyl Laurate.

As a consequence of intense industrialization in the last few decades, the amount of agro-industrial wastes has increasing, where new forms of valorization are crucial. In this work, five residual biomasses from Maranhão (Brazil) were investigated as supports for immobilization of lipase from Thermomyces lanuginosus (TLL). The new biocatalysts BM-TLL (babaçu mesocarp) and RH-TLL (rice husk) showed immobilization efficiencies >98% and hydrolytic activities of 5.331 U g-1 and 4.608 U g-1, respectively, against 142 U g-1 by Lipozyme® TL IM. High esterification activities were also found, with 141.4 U g-1 and 396.4 U g-1 from BM-TLL and RH-TLL, respectively, against 113.5 U g-1 by TL IM. Results of porosimetry, SEM, and BET demonstrated BM and RH supports are mesoporous materials with large hydrophobic area, allowing a mixture of hydrophobic adsorption and confinement, resulting in hyperactivation of TLL. These biocatalysts were applied in the production of hexyl laurate, where RH-TLL was able to generate 94% conversion in 4 h. Desorption with Triton X-100 and NaCl confirmed that new biocatalysts were more efficient with 5 times less protein than commercial TL IM. All results demonstrated that residual biomass was able to produce robust and stable biocatalysts containing immobilized TLL with better results than commercial preparations.

Improved immobilization of lipase from Thermomyces lanuginosus on a new chitosan-based heterofunctional support: Mixed ion exchange plus hydrophobic interactions.

In this study, a new mixed heterofunctional support (Chit-GA-Gly) has been prepared by sequential activation of chitosan hydrogel (Chit) with glutaraldehyde (GA) and further functionalization with glycine (Gly). The immobilization of the lipase from Thermomyces lanuginosus (TLL) on this support was compared with that on GA-activated Chit hydrogel (Chit-GA). The supports have been characterized by FT-IR, zeta potential and TG analyses. A similar maximum lipase loading of 53-55 mg per gram of support has been obtained for both supports. Both biocatalysts retained ≈40% of their initial activity after 48 h of incubation at 50 °C in heptane, toluene or iso-octane. The immobilization of TLL on Chit-GA proceeded via preferential covalent attachment (95%) and a combined ion exchange (cationic and anionic) and hydrophobic adsorption was observed using Chit-GA-Gly. TLL immobilized on Chit-GA-Gly was ≈4-times more active than when immobilized on Chit-GA in both olive oil emulsion hydrolysis and alkyl palmitate synthesis via esterification. Isoamyl palmitate synthesis in iso-octane at 50 °C using this new biocatalyst gave a maximum acid conversion of 85% after 90 min of reaction. After nine consecutive esterification batches, the biocatalyst retained around 40% of its initial activity.

A new heterofunctional support for enzyme immobilization: PEI functionalized Fe3O4 MNPs activated with divinyl sulfone. Application in the immobilization of lipase from Thermomyces lanuginosus.

Lipase from Thermomyces lanuginosus (TLL) was immobilized onto a novel heterofunctional support, divinyl sulfone (DVS) superparamagnetic nanoparticles (SPMNs) functionalized with polyethyleneimine (PEI). Particle size and zeta potential measurements, elemental analysis, X-ray powder diffraction, magnetic measurements, and infrared spectroscopy analysis were used to characterize the TLL preparations. At pH 10, it was possible to achieve 100 % of immobilization yield in 1 h. The immobilization pH gives TLL preparations with different stabilities; indeed the TLL preparation immobilized at pH 5.0 was the most stable during the thermal inactivation at all pH values. For the hydrolysis of racemic methyl mandelate, the nanobiocatalysts immobilized at pH 5.0 and blocked with ethylenediamine (EDA) and ethanolamine (ETA) obtained good enantioselectivities (68 % and 72 %, respectively) with high catalytic activities in the reaction medium at pH 7.0. The operational stability of the systems was evaluated in the esterification reaction of benzyl alcohol, obtaining up to 61 % conversion after the seventh reaction cycle. These results show that SPMN@PEI-DVS support is a robust strategy for the easy and rapid recovery of the nanobiocatalyst by applying a magnetic field, showing great potential for industrial applications.

Preparation, functionalization and characterization of rice husk silica for lipase immobilization via adsorption.

Silica has been extracted from rice husks via a simple hydrothermal process and functionalized with triethoxy(octyl)silane -OCTES (Octyl-SiO2) and (3-aminopropyl)triethoxysilane - 3-APTES (Amino-SiO2), with the aim of using it as support to immobilize lipase from Thermomyces lanuginosus (TLL) via adsorption. The supports have been characterized by particle size distribution and elemental analyses, XRD, TGA, SEM, AFM and N2 physisorption so as to confirm their functionalization. Effect of pH, temperature, initial protein loading and contact time on the adsorption process has been systematically evaluated. Maximum immobilized protein loading of 12.3 ± 0.1 mg/g for Amino-SiO2 (5 mM buffer sodium acetate at pH 4.0, 25 °C and initial protein loading of 20 mg/g) and 21.9 ± 0.1 mg/g for Octyl-SiO2 (5 mM buffer sodium acetate at pH 5.0, 25 °C and initial protein loading of 30 mg/g) was observed. However, these biocatalysts presented similar catalytic activity in olive oil emulsion hydrolysis (between 630 and 645 U/g). TLL adsorption was a spontaneous process involving physisorption. Experimental data on Octyl-SiO2 and Amino-SiO2 adsorption were well-fitted to the Langmuir isotherm model. It was also investigated whether these biocatalysts could synthesize cetyl esters via esterification reaction. Thus, it was found that cetyl stearate synthesis required 100-110 min of reaction time to attain maximum conversion percentage (around 94%). Ester productivity of immobilized TLL on Amino-SiO2 was 1.3-3.1 times higher than Octyl-SiO2.

Preparation of ion-exchange supports via activation of epoxy-SiO2 with glycine to immobilize microbial lipase - Use of biocatalysts in hydrolysis and esterification reactions.

Ion-exchange supports have been prepared via sequential functionalization of silica-based materials with (3­Glycidyloxypropyl)trimethoxysilane (GPTMS) (Epx-SiO2) and activation with glycine (Gly-Epx-SiO2) in order to immobilize lipase from Thermomyces lanuginosus (TLL) via adsorption. Rice husk silica (RHS) was selected as support with the aim of comparing its performance with commercial silica (Immobead S60S). Sequential functionalization/activation of SiO2-based supports has been confirmed by AFM, SEM and N2 adsorption-desorption analyses. Maximum TLL adsorption capacities of 14.8 ±â€¯0.1 mg/g and 16.1 ±â€¯0.6 mg/g using RHS and Immobead S60S as supports, respectively, have been reached. The Sips isotherm model has been used which was well fitted to experimental data on TLL adsorption. Catalytic activities of immobilized TLL were assayed by olive oil emulsion hydrolysis and butyl stearate synthesis via an esterification reaction. Hydrolytic activity of the biocatalyst prepared with a commercial support (357.6 ±â€¯11.2 U/g) was slightly higher than that of Gly-Epx-SiO2 prepared with RHS (307.4 ±â€¯7.2 U/g). On the other hand, both biocatalysts presented similar activity (around 90% conversion within 9-10 h of reaction) and reusability after 6 consecutive cycles of butyl stearate synthesis in batch systems.

Chemoenzymatic synthesis of new derivatives of glycyrrhetinic acid with antiviral activity. Molecular docking study.

We present an efficient approach to the synthesis of a series of glycyrrhetinic acid derivatives. Six derivatives, five of them new compounds, were obtained through chemoenzymatic reactions in very good to excellent yield. In order to find the optimal reaction conditions, the influence of various parameters such as enzyme source, nucleophile:substrate ratio, enzyme:substrate ratio, solvent and temperature was studied. The excellent results obtained by lipase catalysis made the procedure very efficient considering their advantages such as mild reaction conditions and low environmental impact. Moreover, in order to explain the reactivity of glycyrrhetinic acid and the acetylated derivative to different nucleophiles in the enzymatic reactions, molecular docking studies were carried out. In addition, one of the synthesized compounds exhibited remarkable antiviral activity against TK + and TK- strains of Herpes simplex virus type 1 (HSV-1), sensitive and resistant to acyclovir (ACV) treatment.

Insights into Hydrocarbon Assimilation by Eurotialean and Hypocrealean Fungi: Roles for CYP52 and CYP53 Clans of Cytochrome P450 Genes.

Several filamentous fungi are able to concomitantly assimilate both aliphatic and polycyclic aromatic hydrocarbons that are the biogenic by-products of some industrial processes. Cytochrome P450 monooxygenases catalyze the first oxidation reaction for both types of substrate. Among the cytochrome P450 (CYP) genes, the family CYP52 is implicated in the first hydroxylation step in alkane-assimilation processes, while genes belonging to the family CYP53 have been linked with oxidation of aromatic hydrocarbons. Here, we perform a comparative analysis of CYP genes belonging to clans CYP52 and CYP53 in Aspergillus niger, Beauveria bassiana, Metarhizium robertsii (formerly M. anisopliae var. anisopliae), and Penicillium chrysogenum. These species were able to assimilate n-hexadecane, n-octacosane, and phenanthrene, exhibiting a species-dependent modification in pH of the nutrient medium during this process. Modeling of the molecular docking of the hydrocarbons to the cytochrome P450 active site revealed that both phenanthrene and n-octacosane are energetically favored as substrates for the enzymes codified by genes belonging to both CYP52 and CYP53 clans, and thus appear to be involved in this oxidation step. Analyses of gene expression revealed that CYP53 members were significantly induced by phenanthrene in all species studied, but only CYP52X1 and CYP53A11 from B. bassiana were highly induced with n-alkanes. These findings suggest that the set of P450 enzymes involved in hydrocarbon assimilation by fungi is dependent on phylogeny and reveal distinct substrate and expression specificities.

Lipozyme TL IM as Catalyst for the Synthesis of Eugenyl Acetate in Solvent-Free Acetylation.

The ability of commercial immobilized lipase from Thermomyces lanuginosus (Lipozyme TL IM) to catalyze the acetylation of essential clove oil with acetic anhydride in a solvent-free system was studied, and the antimicrobial activity of the ester formed was evaluated as well. Experimental design based on two variables (eugenol to acetic anhydride molar ratio and temperature) was employed to evaluate the experimental conditions of eugenyl acetate ester production. The maximum conversion yield (92.86 %) was obtained using Lipozyme TL IM (5 wt%, based on the total amount of substrates), with eugenol to acetic anhydride molar ratio of 1:5 at 70 °C. The chemical structure of the eugenyl acetate ester obtained at the optimized condition, and purified, was confirmed by the proton nuclear magnetic resonance ((1)H-NMR) analysis. The antimicrobial activity of eugenyl acetate ester was proven effective on Gram-positive and Gram-negative bacteria, with means of 16.62 and 17.55 mm of inhibition halo.

Optimized butyl butyrate synthesis catalyzed by Thermomyces lanuginosus lipase.

Butyl butyrate is an ester present in pineapple flavor, which is very important for the food and beverages industries. In this work, the optimization of the reaction of butyl butyrate synthesis catalyzed by the immobilized lipase Lipozyme TL-IM was performed. n-Hexane was selected as the most appropriate solvent. Other reaction parameters such as temperature, substrate molar ratio, biocatalyst content and added water, and their responses measured as yield, were evaluated using a fractional factorial design, followed by a central composite design (CCD) and response surface methodology. In the fractional design 2(4-1) , the four variables were tested and temperature and biocatalyst content were statistically significant and then used for optimization on CCD. The optimal conditions for butyl butyrate synthesis were found to be 48°C; substrate molar ratio 3:1 (butanol:butyric acid); biocatalyst content of 40% of acid mass. Under these conditions, over 90% of yield was obtained in 2 h. Enzyme reuse was tested by washing the biocatalyst with n-hexane or by direct reuse. The direct reuse produced a rapid decrease on enzyme activity, while washing with n-hexane allowed reusing the enzyme for five reactions cycles keeping approximately 85% of its activity.

A specific short dextrin-hydrolyzing extracellular glucosidase from the thermophilic fungus Thermoascus aurantiacus 179-5.

The thermophilic fungus Thermoascus aurantiacus 179-5 produced large quantities of a glucosidase which preferentially hydrolyzed maltose over starch. Enzyme production was high in submerged fermentation, with a maximal activity of 30 U/ml after 336 h of fermentation. In solid-state fermentation, the activity of the enzyme was 22 U/ml at 144 h in medium containing wheat bran and 5.8 U/ml at 48 h when cassava pulp was used as the culture medium. The enzyme was specific for maltose, very slowly hydrolyzed starch, dextrins (2-7G) and the synthetic substrate (alpha-PNPG), and did not hydrolyze sucrose. These properties suggest that the enzyme is a type II alpha-glucosidase. The optimum temperature of the enzyme was 70 degrees . In addition, the enzyme was highly thermostable (100% stability for 10 h at 60 degrees and a half-life of 15 min at 80 degrees), and stable within a wide pH range.