Addition of sodium malonate alters the morphology and increases the critical flux during tangential flow filtration of precipitated immunoglobulins.

Recent studies have demonstrated that one can control the packing density, and in turn the filterability, of protein precipitates by changing the pH and buffer composition of the precipitating solution to increase the structure/order within the precipitate. The objective of this study was to examine the effect of sodium malonate, which is known to enhance protein crystallizability, on the morphology of immunoglobulin precipitates formed using a combination of ZnCl2 and polyethylene glycol. The addition of sodium malonate significantly stabilized the precipitate particles as shown by an increase in melting temperature, as determined by differential scanning calorimetry, and an increase in the enthalpy of interaction, as determined by isothermal titration calorimetry. The sodium malonate also increased the selectivity of the precipitation, significantly reducing the coprecipitation of DNA from a clarified cell culture fluid. The resulting precipitate had a greater packing density and improved filterability, enabling continuous tangential flow filtration with minimal membrane fouling relative to precipitates formed under otherwise identical conditions but in the absence of sodium malonate. These results provide important insights into strategies for controlling precipitate morphology to enhance the performance of precipitation-filtration processes for the purification of therapeutic proteins.

Advancement of membrane separation technology for organic pollutant removal.

In the face of growing global freshwater scarcity, the imperative to recycle and reuse water becomes increasingly apparent across industrial, agricultural, and domestic sectors. Eliminating a range of organic pollutants in wastewater, from pesticides to industrial byproducts, presents a formidable challenge. Among the potential solutions, membrane technologies emerge as promising contenders for treating diverse organic contaminants from industrial, agricultural, and household origins. This paper explores cutting-edge membrane-based approaches, including reverse osmosis, nanofiltration, ultrafiltration, microfiltration, gas separation membranes, and pervaporation. Each technology's efficacy in removing distinct organic pollutants while producing purified water is scrutinized. This review delves into membrane fouling, discussing its influencing factors and preventative strategies. It sheds light on the merits, limitations, and prospects of these various membrane techniques, contributing to the advancement of wastewater treatment. It advocates for future research in membrane technology with a focus on fouling control and the development of energy-efficient devices. Interdisciplinary collaboration among researchers, engineers, policymakers, and industry players is vital for shaping water purification innovation. Ongoing research and collaboration position us to fulfill the promise of accessible, clean water for all.

Development of microfiltration membranes based on polysulfone and polyetherimide blends.

In this study, membranes blended with polysulfone (PSU) and polyetherimide (PEI) polymers in different ratios were fabricated. Their potential to remove pollutants from rivers, which are a potential drinking water source, was investigated. Scanning electron microscopy analysis revealed that the PSU membranes had a dense and homogeneous layer, whereas the addition of PEI formed a spongy substrate. The water content of the fabricated membranes varied between 5.37 and 22.42%, porosities 28.73-89.36%, contact angles 69.18-85.81%, and average pure water fluxes 257.25-375.32 L/m2 h. The blended membranes removed turbidity, chloride, alkalinity, conductivity, sulfate, iron, manganese, and total organic carbon up to 98.32, 92.28, 96.87, 90.67, 99.58, 94.63, 97.48, and 79.11%, respectively. These results show that when PEI was added to the PSU polymer, the filtration efficiency increased owing to an increase in the hydrophilicity of the membranes. Blending these two polymers enabled the optimization of membrane properties such as permeability, selectivity, and mechanical strength. In addition, membrane fabrication processes are simple and incur low costs.

A quantitative comparison of urine centrifugation and filtration for the isolation and analysis of urinary nucleic acid biomarkers.

Urine is a rich source of nucleic acid biomarkers including cell-free DNA (cfDNA) and RNA for monitoring the health of kidney allografts. In this study, we aimed to evaluate whether urine filtration can serve as an alternative to the commonly used method of centrifugation to collect urinary fluid and cell pellets for isolating cfDNA and cellular messenger RNA (mRNA). We collected urine specimens from kidney allograft recipients and obtained the urine supernatant and cell pellet from each specimen using both filtration and centrifugation for paired analyses. We performed DNA sequencing to characterize the origin and properties of cfDNA, as well as quantitative PCR of mRNAs extracted from cell fractions. Our results showed that the biophysical properties of cfDNA, the microbial DNA content, and the tissues of origin of cfDNA were comparable between samples processed using filtration and centrifugation method. Similarly, mRNA quality and quantity obtained using both methods met our criteria for downstream application and the Ct values for each mRNA were comparable between the two techniques.The Ct values demonstrated a high degree of correlation. These findings suggest that urine filtration is a viable alternative to urine centrifugation for isolation of nucleic acid biomarkers from urine specimens.

Adverse effects of Microcystis aeruginosa exudates on the filtration, digestion, and reproduction organs of benthic bivalve Corbicula fluminea.

Cyanobacteria bloom and the secondary metabolites released by the microorganism are extremely harmful to aquatic animals, yet study on their adverse effects in zoobenthos is rare. Corbicula fluminea widely distributed in freshwater environment with algal blooms. It is a typical filter feeding zoobenthos that may be affected by the secondary metabolites of cyanobacteria due to its high filtering rate. In this study, C. fluminea was exposed to Microcystis aeruginosa exudates (MaE) for 96 h, which was obtained from 5 × 105 cells/mL and 2.5 × 106 cells/mL exponential stage M. aeruginosa culture solution that represented cyanobacteria cell density needs environmental risk precaution control and emergent control, respectively. The responses of C. fluminea critical organs to MaE were analyzed and evaluated based on histopathological sections, antitoxicity biomarkers, and organ function biomarkers. The results showed that all the organs underwent structural disorders, cell vacuolization, apoptosis, and necrosis, and the damage levels increased as MaE concentration increased. The detoxification and antioxidant defense systems biomarkers in each organ response to MaE exposure differently and the level of reaction improved when MaE concentration increased. The siphon rate and acetylcholinesterase activity showed that the filtration function decreased significantly as the MaE concentration increased. Increased activity of glutathione S-transferase and amylase in the digestive gland indicate that it is the major detoxification organ of C. fluminea. Increased vitellogenin concentration and enlarged oocytes in the gonad indicate that MaE may have an estrogenic effect on C. fluminea. This study demonstrates that cyanobacteria threat benthic bivalves by inducing oxidative stress, inhibiting filtering feeding system, and disturbing digestion system and reproduction potential of C. fluminea.

Biofiltration of toluene in the presence of ethyl acetate or n-hexane: Performance and microbial community.

This study describes the operation of two independent parallel laboratory-scale biotrickling filters (BTFs) to degrade different types of binary volatile organic compound (VOC) mixtures. Comparison experiments were conducted to evaluate the effects of two typical VOCs, i.e., ethyl acetate (a hydrophilic VOC) and n-hexane (a hydrophobic VOC) on the removal performance of toluene (a moderately hydrophobic VOC) in BTFs ''A" and ''B", respectively. Experiments were carried out by stabilizing the toluene concentration at 1.64 g m-3 and varying the concentrations of gas-phase ethyl acetate (0.85-2.8 g m-3) and n-hexane (0.85-2.8 g m-3) at an empty bed residence time (EBRT) of 30 s. In the presence of ethyl acetate (850 ± 55 mg m-3), toluene exhibited the highest removal efficiency (95.4 ± 2.2%) in BTF "A". However, the removal rate of toluene varied from 48.1 ± 6.9% to 70.1 ± 6.8% when 850 ± 123 mg m-3 to 2800 ± 136 mg m-3 of n-hexane was introduced into BTF "B". The high-throughput sequencing data revealed that the genera Pseudomonas and Comamonadaceae_unclassified are the core microorganisms responsible for the degradation of toluene. The intensity of the inhibitory or synergistic effects on toluene removal was influenced by the type and concentration of the introduced VOC, as well as the number and activity of the genera Pseudomonas and Comamonadaceae_unclassified. It provides insights into the interaction between binary VOCs during biofiltration from a microscopic perspective.

A new sustainable filtration membrane extraction method based on nanoconfined liquid phase extraction: Determination of organochlorinated pesticides and pyrethroids in tea samples.

BACKGROUND: Pesticides are used in agricultural production for prevent and control crop diseases and pests, but it is easy to cause excessive pesticides residues in agricultural products, polluting the environment and endangering human health. Due to their unmatched and sustainable capabilities, nanoextraction procedures are becoming every day more important in Analytical Chemistry. In particular, nanoconfined liquid phase extraction has shown extraction capabilities toward polar, medium polar, and/or nonpolar substances, which can be easily modulated depending on the nanoconfined solvent used. Furthermore, this "green" technique showed excellent characteristics in terms of recoveries, extraction time (≤1 min), reliability, and versatility. (97) RESULTS: In this work, the advantages of this technique have been coupled with those of filtration membrane extraction, making use of carbon nanofibers (CnFs) growth on carbon microspheres (CµS). This substrate has been deposited on a filter, which combined with gas chromatographic mass spectrometry (GC-MS) analysis successfully employed for the nanoextraction of 30 pesticides (18 organochlorine and 12 pyrethroids) in tea samples. Under the optimized extraction conditions, the linear range with standard solutions was from 1 to 1000 ng mL-1 (R2 ≥ 0.99), the limit of detections in tea samples were in the range 0.56-17.98 µg kg-1. The accuracy of the developed method was evaluated by measuring the extraction recovery of the spiked tea samples, and recoveries between 74.41 % and 115.46 %. (119) SIGNIFICANCE: Considering the versatility of nanoconfined liquid phase extraction and the functionality of the filtration membrane extraction procedure, this new extraction method can be considered a powerful candidate for automatized high-throughput analyses of real samples. (34).

Protein loss during membrane processes in biopharmaceutical manufacturing.

Maximizing product yield in biopharmaceutical manufacturing processes is a critical factor in determining the overall cost of goods, especially given the high value of these biological products. However, there has been relatively limited research on the quantitative analysis of protein losses due to adsorption and fouling during the different membrane filtration processes employed in typical downstream operations. This study aims to provide a comprehensive analysis of protein loss in the range of membrane systems used in downstream processing including clarification, virus removal filtration, ultrafiltration/diafiltration for formulation, and final sterile filtration, all using commercially available membranes with three model proteins (bovine serum albumin, human serum albumin, and immunoglobulin G). The correlation between protein loss and various parameters (i.e., protein type, protein concentration, throughput, membrane morphology, and protein removal mechanism) was also investigated. This study provides important insights into the nature of protein loss during membrane processes as well as a methodology for quantifying protein yield loss in bioprocesses.

Pre-analytical challenges from adsorptive losses associated with thiamine analysis.

Thiamine (vitamin B1) is an essential vitamin serving in its diphosphate form as a cofactor for enzymes in the citric acid cycle and pentose-phosphate pathways. Its concentration reported in the pM and nM range in environmental and clinical analyses prompted our consideration of the components used in pre-analytical processing, including the selection of filters, filter apparatuses, and sample vials. The seemingly innocuous use of glass fiber filters, glass filter flasks, and glass vials, ubiquitous in laboratory analysis of clinical and environmental samples, led to marked thiamine losses. 19.3 nM thiamine was recovered from a 100 nM standard following storage in glass autosampler vials and only 1 nM of thiamine was obtained in the filtrate of a 100 nM thiamine stock passed through a borosilicate glass fiber filter. We further observed a significant shift towards phosphorylated derivatives of thiamine when an equimolar mixture of thiamine, thiamine monophosphate, and thiamine diphosphate was stored in glass (most notably non-silanized glass, where a reduction of 54% of the thiamine peak area was observed) versus polypropylene autosampler vials. The selective losses of thiamine could lead to errors in interpreting the distribution of phosphorylated species in samples. Further, some loss of phosphorylated thiamine derivatives selectively to amber glass vials was observed relative to other glass vials. Our results suggest the use of polymeric filters (including nylon and cellulose acetate) and storage container materials (including polycarbonate and polypropylene) for thiamine handling. Losses to cellulose nitrate and polyethersulfone filters were far less substantial than to glass fiber filters, but were still notable given the low concentrations expected in samples. Thiamine losses were negated when thiamine was stored diluted in trichloroacetic acid or as thiochrome formed in situ, both of which are common practices, but not ubiquitous, in thiamine sample preparation.

Standard addition method for rapid, cultivation-independent quantification of Legionella pneumophila cells by qPCR in biotrickling filters.

Cultivation-independent molecular biological methods are essential to rapidly quantify pathogens like Legionella pneumophila (L. pneumophila) which is important to control aerosol-generating engineered water systems. A standard addition method was established to quantify L. pneumophila in the very complex matrix of process water and air of exhaust air purification systems in animal husbandry. Therefore, cryopreserved standards of viable L. pneumophila were spiked in air and water samples to calibrate the total bioanalytical process which includes cell lysis, DNA extraction, and qPCR. A standard addition algorithm was employed for qPCR to determine the initial concentration of L. pneumophila. In mineral water, the recovery rate of this approach (73%-134% within the concentration range of 100-5000 Legionella per mL) was in good agreement with numbers obtained from conventional genomic unit (GU) calibration with DNA standards. In air samples of biotrickling filters, in contrast, the conventional DNA standard approach resulted in a significant overestimation of up to 729%, whereas our standard addition gave a more realistic recovery of 131%. With this proof-of-principle study, we were able to show that the molecular biology-based standard addition approach is a suitable method to determine realistic concentrations of L. pneumophila in air and process water samples of biotrickling filter systems. Moreover, this quantification strategy is generally a promising method to quantify pathogens in challenging samples containing a complex microbiota and the classical GU approach used for qPCR leads to unreliable results.

Tutorial review of error evaluation in experimental water research at the example of membrane filtration.

Experimental water research lacks clear methodology to estimate experimental error. Especially when natural waters are involved, the characterization tools bear method-specific artifacts while the varying environmental conditions prevent regular repeats. This tutorial review identifies common mistakes, and proposes a practical procedure to determine experimental errors at the example of membrane filtration. Statistical analysis is often applied to an insufficient number of repeated measurements, while not all error sources and contributions are considered. This results in an underestimation of the experimental error. Variations in relevant experimental parameters need to be investigated systematically, and the related errors are quantified as a half of the variation between the max and min values when standard deviation is not applicable. Error of calculated parameters (e.g. flux, pollutant removal and mass loss) is estimated by applying error propagation, where weighing contributions of the experimental parameters are considered. Appropriate judgment and five-time repetition of a selected experiment under identical conditions are proposed to validate the propagated experimental error. For validation, the five repeated data points should lie within the estimated error range of the error bar. The proposed error evaluation procedure is adaptable in experimental water research and intended for researchers to identify the contributing factors of an experimental error and carry out appropriate error quantification and validation. The most important aim is to raise awareness of the necessity to question error methodology and reproducibility of experimental data, to produce and publish high quality research.

Empowering powdered activated carbon (PAC) with 3D printing: Achieving highly efficient and reusable cationic dye removal.

Powdered activated carbon (PAC) has been extensively used as an effective adsorbent. Despite its excellent adsorption ability, PAC has drawbacks, including difficulty in filtration and reactivation after use, limitations of mass transfer in deeper areas because of its aggregated powder form, and limited applicability in high-flow systems. To overcome these limitations, we used a three-dimensional (3D) printing system to fabricate PAC into a 3D structure. Spectral and microscopic analyses indicated that PAC was embedded into 3D monolith and exhibited high porosity suitable for facile mass transfer. The designed 3D PAC filter effectively removed 200 ppm-methylene blue (MB) within 8 h and showed an adsorption efficiency of 93.4 ± 0.9%. The adsorption of MB onto the 3D PAC filter was described by the pseudo-first-order kinetic and Freundlich isotherm models. The negatively charged 3D PAC filter might attract the positively charged MB, thus favoring the physical adsorption of MB onto the 3D PAC filter. The adsorption performance of the 3D PAC filter was tested at various pH levels of 4-10 and against MB spiked in seawaters and freshwaters to evaluate its feasibility for use in real environments. Finally, the reproducibility and reusability of the 3D PAC filter were demonstrated through repeated adsorption and desorption processes against MB.

Biofouling mitigation of Nb2AlC and Mo3AlC2 MXene-precursors doped polyether sulfone mixed matrix membranes for pathogen microorganisms.

This study explores the incorporation of Nb2AlC and Mo3AlC2 MAX phases, known for their nano-layered structure, into polyether sulfone (PES) membranes to enhance their antifouling and permeability properties for pathogen microorganism filtration against bovine serum albumin (BSA) and Escherichia coli (E. coli). The composite membranes were characterized for their structural and morphological properties, and their performance in mitigating biofouling was evaluated. The structural characterizations have been performed for all the prepared MAX phases and corresponding composite membranes. The antioxidant ability of Nb2AlC and Mo3AlC2 MAX phases was defined by the DPPH radical scavenging assay, and the highest antioxidant ability was found to be 59.35 %, while 53.69 % scavenging potential was recorded at 100 mg/L. The percentage scavenging ability was raised with an increase in concentrations. The antimicrobial properties of MAX phases, evaluated as the minimum inhibitory concentration, were stated against several pathogen microorganisms. The tested compounds of Nb2AlC and Mo3AlC2 composites containing MAX phases exhibited excellent chemical nuclease activity, and it was determined that Nb2AlC caused double strand DNA cleavage activity while Mo3AlC2 induced the complete fragmentation of the DNA molecule. Biofilm inhibition of Nb2AlC and Mo3AlC2 MAX phases was studied against Staphylococcus aureus, and Pseudomonas aeruginosa and the maximum biofilm inhibition of Nb2AlC and Mo3AlC2 MAX phases was found to be 77.15 % and 69.07 % against S. aureus and also 69.74 % and 65.01 % against P. aeruginosa. Furthermore, Nb2AlC and Mo3AlC2 MAX phases demonstrated excellent E. coli growth inhibition of 100 % at 125 and 250 mg/L.

Highly Reactive Peroxide Species Promoted Soot Oxidation over an Ordered Macroporous Ce0.8Zr0.2O2 Integrated Catalyzed Diesel Particulate Filter.

Particulate matter, represented by soot particles, poses a significant global environmental threat, necessitating efficient control technology. Here, we innovatively designed and elaborately fabricated ordered hierarchical macroporous catalysts of Ce0.8Zr0.2O2 (OM CZO) integrated on a catalyzed diesel particulate filter (CDPF) using the self-assembly method. An oxygen-vacancy-enriched ordered macroporous Ce0.8Zr0.2O2 catalyst (VO-OM CZO) integrated CDPF was synthesized by subsequent NaBH4 reduction. The VO-OM CZO integrated CDPF exhibited a markedly enhanced soot oxidation activity compared to OM CZO and powder CZO coated CDPFs (T50: 430 vs 490 and 545 °C, respectively). The well-defined OM structure of the VO-OM CZO catalysts effectively improves the contact efficiency between soot and the catalysts. Meanwhile, oxygen vacancies trigger the formation of a large amount of highly reactive peroxide species (O22-) from molecular oxygen (O2) through electron abstraction from the three adjacent Ce3+ (3Ce3+ + Vö + O2 → 3Ce4+ + O22-), contributing to the efficient soot oxidation. This work demonstrates the fabrication of the ordered macroporous CZO integrated CDPF and reveals the importance of structure and surface engineering in soot oxidation, which sheds light on the design of highly efficient PM capture and removal devices.

Riboflavin based setup as an alternative method for a preliminary screening of face mask filtration efficiency.

Face masks are essential in reducing the transmission of respiratory infections and bacterial filtration efficiency, a key parameter of mask performances, requires the use of Staphylococcus aureus and specialised staff. This study aims to develop a novel method for a preliminary screening of masks or materials filtration efficiency by a green, easy and rapid setup based on the use of a riboflavin solution, a safe autofluorescent biomolecule. The proposed setup is composed of a commercial aerosol generator commonly used for aerosol therapy, custom 3D printed aerosol chamber and sample holder, a filter for downstream riboflavin detection and a vacuum pump. The filtration efficiency of four different masks was assessed using the riboflavin-based setup and the bacterial filtration efficiency (BFE). The averaged filtration efficiency values, measured with both methods, were similar but were higher for the riboflavin-based setup (about 2% for all tested samples) than bacterial filtration efficiency. Considering the good correlation, the riboflavin-based setup can be considered validated as an alternative method to bacterial filtration efficiency for masks and related materials fabrics filtration efficiency screening but This study aims to develop a novel method for a preliminary screening of masks or materials filtration efficiency by a green, easy and rapid setup based on the use of a riboflavin solution, a safe autofluorescent biomolecule, but not to replace regulation approaches. The proposed setup can be easily implemented at low price, is more rapid and eco-friendly and can be performed in chemical-physical laboratories without the needing of biosafety laboratory and specialised operators.

Response surface optimization of sludge dewatering process: synergistic enhancement by ultrasonic, chitosan and sludge-based biochar.

Due to the colloidal stability, the high compressibility and the high hydration of extracellular polymeric substances (EPS), it is difficult to efficiently dehydrate sludge. In order to enhance sludge dewatering, the process of ultrasonic (US) cracking, chitosan (CTS) re-flocculation and sludge-based biochar (SBB) skeleton adsorption of water-holding substances to regulate sludge dewaterability was proposed. Based on the response surface method, the prediction model of the specific resistance to filtration (SRF) and sludge cake moisture content (MC) was established. The US cracking time and the dosage of CTS and SBB were optimized. The results showed that the optimal parameters of the three were 5.08 s, 10.1 mg/g dry solids (DS) and 0.477 g/g DS, respectively. Meantime, the SRF and MC were 5.4125 × 1011 m/kg and 76.8123%, which significantly improved the sludge dewaterability. According to the variance analysis, it is found that the fitting degree of SRF and MC model is good, which also confirms that there is significant interaction and synergy between US, CTS and SBB, and the contribution of CTS and SBB is greater. Moreover, the process significantly improves the sludge's calorific value and makes its combustion more durable.

Enhanced properties of a positive-charged nanofiltration membrane containing quaternarized chitosan through second interfacial polymerization for the removal of salts and pharmaceuticals.

Nanofiltration (NF) membrane technology has been widely used in the removal of salts and trace organic pollutants, such as pharmaceuticals and personal care products (PPCPs), due to its superiority. A positive-charged composite NF membrane with an active skin layer was prepared by polyethyleneimine (PEI), trimethyl benzene chloride, and quaternate chitosan (HTCC) through second interfacial polymerization on the polyethersulfone ultrafiltration membrane. The physicochemical properties of the nanocomposite membrane were investigated using surface morphology, hydrophilicity, surface charge, and molecular weight cut-off (MWCO). The influence of the concentration and reaction time of PEI and HTCC was documented. The optimized membrane had a MWCO of about 481 Da and possessed a pure water permeability of 25.37 L·m-2·h-1·MPa-1. The results also exhibited salt rejection ability as MgCl2 > CaCl2 > MgSO4 > Na2SO4 > NaCl > KCl, showing a positive charge on the fabricated membrane. In addition, the membrane had higher rejection to atenolol, carbamazepine, amlodipine, and ibuprofen at 89.46, 86.02, 90.12, and 77.21%, respectively. Moreover, the anti-fouling performance and stability of the NF membrane were also improved.

Removal of multiple pesticides from water by different types of membranes.

Pesticides are used in agriculture to protect crops from pathogens, insects, fungi and weeds, but the release of pesticides into surface/groundwater by agriculture runoff and rain has raised serious concerns not only for the environment but also for human health. This study aimed to investigate the impact of surface properties on the performance of seven distinct membrane types utilized in nanofiltration (NF), reverse osmosis (RO) and forward osmosis (FO) processes in eliminating multiple pesticides from spiked water. Out of the membranes tested, two are self-fabricated RO membranes while the rest are commercially available membranes. Our results revealed that the self-fabricated RO membranes performed better than other commercial membranes (e.g., SW30XLE, NF270, Duracid and FO) in rejecting the targeted pesticides by achieving at least 99% rejections regardless of the size of pesticides and their log Kow value. Despite the marginally lower water flux exhibited by the self-fabricated membrane compared to the commercial BW30 membrane, its exceptional ability to reject both mono- and divalent salts renders it more apt for treating water sources containing not only pesticides but also various dissolved ions. The enhanced performance of the self-fabricated RO membrane is mainly attributed to the presence of a hydrophilic interlayer (between the polyamide layer and substrate) and the incorporation of hydrophilic nanosheets in tuning its surface characteristics. The findings of the work provide insight into the importance of membrane surface modification for the application of not only the desalination process but also for the removal of contaminants of emerging concern.

Deciphering linkages between DON and the microbial community for nitrogen removal using two green sorption media in a surface water filtration system.

The presence of dissolved organic nitrogen (DON) in stormwater treatment processes is a continuous challenge because of the intertwined nature of its decomposition, bioavailability, and biodegradability and its unclear molecular characteristics. In this paper, 21 T Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) in combination with quantitative polymerase chain reaction was applied to elucidate the molecular change of DON and microbial population dynamics in a field-scale water filtration system filled with two specialty adsorbents for comparison in South Florida where the dry and wet seasons are distinctive annually. The adsorbents included CPS (clay-perlite and sand sorption media) and ZIPGEM (zero-valent iron and perlite-based green environmental media). Our study revealed that seasonal effects can significantly influence the dynamic characteristics and biodegradability of DON. The microbial population density in the filter beds indicated that three microbial species in the nitrogen cycle were particularly thrived for denitrification, dissimilatory nitrate reduction to ammonium, and anaerobic ammonium oxidation via competition and commensalism relationships during the wet season. Also, there was a decrease in the compositional complexity and molecular weight of the DON groups (CnHmOpN1, CnHmOpN2, CnHmOpN3, and CnHmOpN4), revealed by the 21 T FT-ICR MS bioassay, driven by a microbial population quantified by polymerase chain reaction from the dry to the wet season. These findings indirectly corroborate the assumption that the metabolism of microorganisms is much more vigorous in the wet season. The results affirm that the sustainable materials (CPS and ZIPGEM) can sustain nitrogen removal intermittently by providing a suitable living environment in which the metabolism of microbial species can be cultivated and enhanced to facilitate physico-chemical nitrogen removal across the two types of green sorption media.

Spallation and particles infusion into the extracorporeal circuit during CRRT: a preventable phenomenon.

Patients in intensive care are exposed to the risk of microparticle infusion via extracorporeal lines and the resulting complications. A possible source of microparticle release could be the extracorporeal circuit used in blood purification techniques, such as continuous renal replacement therapy (CRRT). Disposable components of CRRT circuits, such as replacement bags and circuit tubing, might release microparticles such as salt crystals produced by precipitation in replacement bags and plastic microparticles produced by spallation. In-line filtration has proven effective in retaining microparticles both in in-vitro and in-vivo studies. In our study, we performed an in-vitro model of CRRT-treatment with the aim of detecting the microparticles produced and released into the circuit by means of a qualitative and quantitative analysis, after sampling the replacement and patient lines straddling a series of in-line filters. Working pressures and flows were monitored during the experiment. This study showed that microparticles are indeed produced and released into the CRRT circuit. The inclusion of in-line filters in the replacement lines allows to reduce the burden of microparticles infused into the bloodstream during extracorporeal treatments, reducing the concentration of microparticles from 14 mg/mL pre in-line filter to 11 mg/mL post in-line filter. Particle infusion and related damage must be counted among the pathophysiological mechanisms supporting iatrogenic damage due to artificial cross-talk between organs during CRRT applied to critically ill patients. This damage can be reduced by using in-line filters in the extracorporeal circuit.