Removal of hexavalent chromium in dual-chamber microbial fuel cells separated by different ion exchange membranes.

An ion exchange membrane (IEM) is an important component in dual-chamber microbial fuel cells (MFCs) to separate cathodic chromium from anode bacteria to avoid toxicity. Common used IEMs (e.g., BPM, CEM, PEM, AEM) have different ionic transfer abilities which could influence MFC performance and chromium removal. Additionally, to distinguish chromium "removal" or "reduction" by MFCs, the chromium removal in this study was further analyzed into cathodic reduction, adsorption on the membrane and permeation through membrane to the anode chamber. It was found that BPM achieved the best performance in removing hexavalent chromium (99.4 ± 0.2 %) and balancing pH and conductivity in both chambers, followed by AEM (97.9 ± 0.8 %) and CEM (95.6 ± 0.8 %), while PEM can not well maintain pH and conductivity leading to the worst anode performance and lowest chromium removal efficiency. However, the adsorption of chromium on the AEM accounts for 91.1 ± 0.7 %, which was much higher than the other three membranes. The permeation of chromium through the membrane were all lower than 0.2% which can be ignored. SEM and EDS results showed that chromium deposits and bacteria were detected on the membrane facing cahtode and anode, respectively, indicating that membrane scaling and fouling were inevitable and happened within 24 h operation.

Self-standing Electrochemical Set-up to Enrich Anode-respiring Bacteria On-site.

Anaerobic respiration coupled with electron transport to insoluble minerals (referred to as extracellular electron transport [EET]) is thought to be critical for microbial energy production and persistence in many subsurface environments, especially those lacking soluble terminal electron acceptors. While EET-capable microbes have been successfully isolated from various environments, the diversity of bacteria capable of EET is still poorly understood, especially in difficult-to-sample, low energy or extreme environments, such as many subsurface ecosystems. Here, we describe an on-site electrochemical system to enrich EET-capable bacteria using an anode as a respiratory terminal electron acceptor. This anode is connected to a cathode capable of catalyzing abiotic oxygen reduction. Comparing this approach with electrocultivation methods that use a potentiostat for poising the electrode potential, the two-electrode system does not require an external power source. We present an example of our on-site enrichment utilized in an alkaline pond at the Cedars, a terrestrial serpentinization site in Northern California. Prior attempts to cultivate mineral reducing bacteria were unsuccessful, which is likely due to the low-biomass nature of this site and/or the low relative abundance of metal reducing microbes. Prior to implementing our two-electrode enrichment, we measured the vertical profile of dissolved oxygen concentration. This allowed us to place the carbon felt anode and platinum-electroplated carbon felt cathode at depths that would support anaerobic and aerobic processes, respectively. Following on-site incubation, we further enriched the anodic electrode in the laboratory and confirmed a distinct microbial community compared to the surface-attached or biofilm communities normally observed at the Cedars. This enrichment subsequently led to the isolation of the first electrogenic microbe from the Cedars. This method of on-site microbial enrichment has the potential to greatly enhance the isolation of EET-capable bacteria from low biomass or difficult to sample habitats.

Microbial fuel cells for clogging assessment in constructed wetlands.

Clogging in HSSF CW may result in a reduction of system's life-span or treatment efficiency. Current available techniques to assess the degree of clogging in HSSF CW are time consuming and cannot be applied on a continuous basis. Main objective of this work was to assess the potential applicability of microbial fuel cells for continuous clogging assessment in HSSF CW. To this aim, two replicates of a membrane-less microbial fuel cell (MFC) were built up and operated under laboratory conditions for five weeks. The MFC anode was gravel-based to simulate the filter media of HSSF CW. MFC were weekly loaded with sludge that had been accumulating for several years in a pilot HSSF CW treating domestic wastewater. Sludge loading ranged from ca. 20kgTS·m(-3)CW·year(-1) at the beginning of the study period up to ca. 250kgTS·m(-3)CW·year(-1) at the end of the study period. Sludge loading applied resulted in sludge accumulated within the MFC equivalent to a clogging degree ranging from 0.2years (ca. 0.5kgTS·m(-3)CW) to ca. 5years (ca. 10kgTS·m(-3)CW). Results showed that the electric charge was negatively correlated to the amount of sludge accumulated (degree of clogging). Electron transference (expressed as electric charge) almost ceased when accumulated sludge within the MFC was equivalent to ca. 5years of clogging (ca. 10kgTS·m(-3)CW). This result suggests that, although longer study periods under more realistic conditions shall be further performed, HSSF CW operated as a MFC has great potential for clogging assessment.

Spatio-temporal resolution of primary processes of photosynthesis.

Technical progress in laser-sources and detectors has allowed the temporal and spatial resolution of chemical reactions down to femtoseconds and Å-units. In photon-excitable systems the key to chemical kinetics, trajectories across the vibrational saddle landscape, are experimentally accessible. Simple and thus well-defined chemical compounds are preferred objects for calibrating new methodologies and carving out paradigms of chemical dynamics, as shown in several contributions to this Faraday Discussion. Aerobic life on earth is powered by solar energy, which is captured by microorganisms and plants. Oxygenic photosynthesis relies on a three billion year old molecular machinery which is as well defined as simpler chemical constructs. It has been analysed to a very high precision. The transfer of excitation between pigments in antennae proteins, of electrons between redox-cofactors in reaction centres, and the oxidation of water by a Mn4Ca-cluster are solid state reactions. ATP, the general energy currency of the cell, is synthesized by a most agile, rotary molecular machine. While the efficiency of photosynthesis competes well with photovoltaics at the time scale of nanoseconds, it is lower by an order of magnitude for crops and again lower for bio-fuels. The enormous energy demand of mankind calls for engineered (bio-mimetic or bio-inspired) solar-electric and solar-fuel devices.

[Mechanisms of electron transfer to insoluble terminal acceptors in chemoorganotrophic bacteria].

The mechanisms of electron transfer of association of chemoorganotrophic bacteria to the anode in microbial fuel cells are summarized in the survey. These mechanisms are not mutually exclusive and are divided into the mechanisms of mediator electron transfer, mechanisms of electron transfer with intermediate products of bacterial metabolism and mechanism of direct transfer of electrons from the cell surface. Thus, electron transfer mediators are artificial or synthesized by bacteria riboflavins and phenazine derivatives, which also determine the ability of bacteria to antagonism. The microorganisms with hydrolytic and exoelectrogenic activity are involved in electron transfer mechanisms that are mediated by intermediate metabolic products, which are low molecular carboxylic acids, alcohols, hydrogen etc. The direct transfer of electrons to insoluble anode is possible due to membrane structures (cytochromes, pili, etc.). Association of microorganisms, and thus the biochemical mechanisms of electron transfer depend on the origin of the inoculum, substrate composition, mass transfer, conditions of aeration, potentials and location of electrodes and others, that are defined by technological and design parameters.

Evaluation of Laminaria-based microbial fuel cells (LbMs) for electricity production.

Marine algae represents a sustainable feedstock in microbial fuel cells (MFCs) due to its low water and energy requirements for cultivation, higher capacity to sequester carbondioxide, and high carbohydrate content. Two-compartment MFCs were evaluated under batch-fed mode using Laminaria saccharina as the model for algae-based electron donor, and mixed microbial consortia as the biocatalyst, in the anode compartment. The Laminaria-based MFCs (LBMs) were studied with three different pretreatment conditions for the L. saccharina: (i) autoclaving (Auto), (ii) microwave irradiation (Micro), and (iii) as received treatment (No-Treat). A control was setup to establish base line performance for two-compartment MFCs using glucose as the electron donor in the anode. The performance of LBMs (250 mW/m(2) and 900 mA/m(2)) was on par with glucose-based MFCs. AC impedance analysis revealed that the charge transfer resistance was at least 50-fold higher than the corresponding ohmic losses in both LBMs and glucose-based MFCs.

Atopic dermatitis and indoor use of energy sources in cooking and heating appliances.

BACKGROUND: Atopic dermatitis (AD) prevalence has considerably increased worldwide in recent years. Studying indoor environments is particularly relevant, especially in industrialised countries where many people spend 80% of their time at home, particularly children. This study is aimed to identify the potential association between AD and the energy source (biomass, gas and electricity) used for cooking and domestic heating in a Spanish schoolchildren population. METHODS: As part of the ISAAC (International Study of Asthma and Allergies in Childhood) phase III study, a cross-sectional population-based survey was conducted with 21,355 6-to-7-year-old children from 8 Spanish ISAAC centres. AD prevalence, environmental risk factors and the use of domestic heating/cooking devices were assessed using the validated ISAAC questionnaire. Crude and adjusted odds ratios (cOR, aOR) and 95% confidence intervals (CIs) were obtained. A logistic regression analysis was performed (Chi-square test, p-value < 0.05). RESULTS: It was found that the use of biomass systems gave the highest cORs, but only electric cookers showed a significant cOR of 1.14 (95% CI: 1.01-1.27). When the geographical area and the mother's educational level were included in the logistic model, the obtained aOR values differed moderately from the initial cORs. Electric heating was the only type which obtained a significant aOR (1.13; 95% CI: 1.00-1.27). Finally, the model with all selected confounding variables (sex, BMI, number of siblings, mother's educational level, smoking habits of parents, truck traffic and geographical area), showed aOR values which were very similar to those obtained in the previous adjusted logistic analysis. None of the results was statistically significant, but the use of electric heating showed an aOR close to significance (1.14; 95% CI: 0.99-1.31). CONCLUSION: In our study population, no statistically significant associations were found between the type of indoor energy sources used and the presence of AD.

Membrane materials for addressing energy and environmental challenges.

Our modern society must solve various severe problems to maintain and increase our quality of life: from water stress to global warming, to fossil fuel depletion, to environmental pollution. The process intensification (PI) strategy is expected to contribute to overcoming many of these issues by facilitating the transition from a resource-intensive to a knowledge-intensive industrial system that will guarantee sustainable growth. Membrane operations, which respond efficiently to the requirements of the PI strategy, have the potential to replace conventional energy-intensive separation techniques, which will boost the efficiency and reduce the environmental impact of separations as well as conversion processes. This work critically reviews the current status and emerging applications of (integrated) membrane operations with a special focus on energy and environmental applications.

Various voltage productions by microbial fuel cells with sedimentary inocula taken from different sites in one freshwater lake.

In this study, single-chamber microbial fuel cells (MFCs) were inoculated with sedimentary samples taken from one freshwater shallow lake. After 98 days of operation, it was found that sedimentary inocula had strong effect on MFC performances, and Fe(III) contents in sediments were significantly related to voltage values produced from MFCs. Inoculation of the sedimentary sample from the site with the highest Fe(III) content led to the production of the highest voltage with a value of 580 mV, while voltage from the MFC inoculated with sediments from the site with the lowest Fe(III) concentration was less than 30 mV at the end of the experiments. In addition, microbial communities of anode biofilms from the MFCs with the highest and lowest voltages showed significant difference. This study will help enable scientific decisions to be made regarding the selection of freshwater sediments as MFC inoculum, and survey exoelectrogenic microorganisms within sediments.

Opportunities for public water utilities in the market of energy from water.

An inventory is made of the possibilities to recover sustainable energy from the water cycle by identifying different water flows in a municipal environment as a sustainable energy source. It is discussed what role public water utilities should play in the market of energy from water. This is done for Waternet, the public water utility of Amsterdam, by describing experiences on two practical applications for aquifer thermal energy storage and energy recovery from drinking water. The main conclusion is that public water utilities can substantially contribute to the production of sustainable energy, especially by making use of heat and cold from the water cycle. Public water utilities have the opportunity to both regulate and enter the market for energy from water.

Characterization of microbial fuel cells at microbially and electrochemically meaningful time scales.

The variable biocatalyst density in a microbial fuel cell (MFC) anode biofilm is a unique feature of MFCs relative to other electrochemical systems, yet performance characterizations of MFCs typically involve analyses at electrochemically relevant time scales that are insufficient to account for these variable biocatalyst effects. This study investigated the electrochemical performance and the development of anode biofilm architecture under different external loadings, with duplicate acetate-fed single-chamber MFCs stabilized at each resistance for microbially relevant time scales. Power density curves from these steady-state reactors generally showed comparable profiles despite the fact that anode biofilm architectures and communities varied considerably, showing that steady-state biofilm differences had little influence on electrochemical performance until the steady-state external loading was much larger than the reactor internal resistance. Filamentous bacteria were dominant on the anodes under high external resistances (1000 and 5000 Ω), while more diverse rod-shaped cells formed dense biofilms under lower resistances (10, 50, and 265 Ω). Anode charge transfer resistance decreased with decreasing fixed external resistances, but was consistently 2 orders of magnitude higher than the resistance at the cathode. Cell counting showed an inverse exponential correlation between cell numbers and external resistances. This direct link of MFC anode biofilm evolution with external resistance and electricity production offers several operational strategies for system optimization.

Greenhouse gas emission reductions from domestic anaerobic digesters linked with sustainable sanitation in rural China.

Anaerobic digesters provide clean, renewable energy (biogas) by converting organic waste to methane, and are a key part of China's comprehensive rural energy plan. Here, experimental and modeling results are used to quantify the net greenhouse gas (GHG) reduction from substituting a household anaerobic digester for traditional energy sources in Sichuan, China. Tunable diode laser absorption spectroscopy and radial plume mapping were used to estimate the mass flux of fugitive methane emissions from active digesters. Using household energy budgets, the net improvement in GHG emissions associated with biogas installation was estimated using global warming commitment (GWC) as a consolidated measure of the warming effects of GHG emissions from cooking. In all scenarios biogas households had lower GWC than nonbiogas households, by as much as 54%. Even biogas households with methane leakage exhibited lower GWC than nonbiogas households, by as much as 48%. Based only on the averted GHG emissions over 10 years, the monetary value of a biogas installation was conservatively estimated at US$28.30 ($16.07 ton(-1) CO(2)-eq), which is available to partly offset construction costs. The interaction of biogas installation programs with policies supporting improved stoves, renewable harvesting of biomass, and energy interventions with substantial health cobenefits are discussed.

Integrated self-powered microchip biosensor for endogenous biological cyanide.

In this work we developed a fully integrated biofuel cell on a microchip, which consisted of glucose dehydrogenase supported (carbon nanotubes/thionine/gold nanoparticles)(8) multilayer as the anode, and the (carbon nanotubes/polylysine/laccase)(15) multilayer as the cathode. The as-obtained biofuel cell produced open circuit potential 620 mV and power density 302 microW cm(-2), showing great potential as a small power resource of portable electronics. Most importantly, for the first time we demonstrated the feasibility of developing a self-powered biosensor based on the inhibitive effect on microchip enzyme biofuel cell. With cyanide employed as the model analyte, this method showed a linear range of 3.0 x 10(-7) to 5.0 x 10(-4) M and a detection limit with 1.0 x 10(-7) M under the optimal conditions. The detection limit was lower than the acceptable cyanide concentration in drinking water (1.9 x 10(-6) M) according to the World Health Organization (WHO). This self-powered sensor was successfully used to detect the cyanide concentration in a real sample, cassava, which is the main carbohydrate resource in South America and Africa. This presented biosensor combined with a resistor and a multimeter demonstrated the general applicability as a fast and simple detection method in the determination of endogenous biological cyanide.

Bio-electro-Fenton process driven by microbial fuel cell for wastewater treatment.

In this study, we proposed a new concept of utilizing the biological electrons produced from a microbial fuel cell (MFC) to power an E-Fenton process to treat wastewater at neutral pH as a bioelectro-Fenton (Bio-E-Fenton) process. This process can be achieved in a dual-chamber MFC from which electrons were generated via the catalyzation of Shewanella decolorationis S12 in its anaerobic anode chamber and transferred to its aerated cathode chamber equipped with a carbon nanotube (CNT)/gamma-FeOOH composite cathode. In the cathode chamber, the Fenton's reagents including hydrogen peroxide (H(2)O(2)) and ferrous irons (Fe(2+)) were in situ generated. This Bio-E-Fenton process led to the complete decolorization and mineralization of Orange II at pH 7.0 with the apparent first-order rate constants, k(app) = 0.212 h(-1) and k(TOC) = 0.0827 h(-1), respectively, and simultaneously produced a maximum power output of 230 mW m(-2) (normalized to the cathode surface area). The apparent mineralization current efficiency was calculated to be as high as 89%. The cathode composition was an important factor in governing system performance. When the ratio of CNT to gamma-FeOOH in the composite cathode was 1:1, the system demonstrated the fastest rate of Orange II degradation, corresponding to the highest amount of H(2)O(2) formed.

Electricity generation coupled with wastewater treatment using a microbial fuel cell composed of a modified cathode with a ceramic membrane and cellulose acetate film.

A noncompartmented microbial fuel cell (NCMFC) composed of a Mn(IV)-carbon plate and a Fe(III)-carbon plate was used for electricity generation from organic wastewater without consumption of external energy. The Fe(III)-carbon plate, coated with a porous ceramic membrane and a semipermeable cellulose acetate film, was used as a cathode, which substituted for the catholyte and cathode. The Mn(IV)-carbon plate was used as an anode without a membrane or film coating. A solar cell connected to the NCMFC activated electricity generation and bacterial consumption of organic matter contained in the wastewater. More than 99 degrees of the organic matter was biochemically oxidized during wastewater flow through the four NCMFC units. A predominant bacterium isolated from the anode surface in both the conventional and the solar cell-linked NCMFC was found to be more than 99 degrees similar to a Mn(II)-oxidizing bacterium and Burkeholderia sp., based on 16S rDNA sequence analysis. The isolate reacted electrochemically with the Mn(IV)-modified anode and produced electricity in the NCMFC. After 90 days of incubation, a bacterial species that was enriched on the Mn(IV)-modified anode surface in all of the NCMFC units was found to be very similar to the initially isolated predominant species by comparing 16S rDNA sequences.

Experimental investigation on regulated and unregulated emissions of a diesel engine fueled with ultra-low sulfur diesel fuel blended with biodiesel from waste cooking oil.

Experiments were conducted on a 4-cylinder direct-injection diesel engine using ultra-low sulfur diesel, bi oesel and their blends, to investigate the regulated and unregulated emissions of the engine under five engine loads at an engine speed of 1800 rev/min. Blended fuels containing 19.6%, 39.4%, 59.4% and 79.6% by volume of biodiesel, corresponding to 2%, 4%, 6% and 8% by mass of oxygen in the blended fuel, were used. Biodiesel used in this study was converted from waste cooking oil. The following results are obtained with an increase of biodiesel in the fuel. The brake specific fuel consumption and the brake thermal efficiency increase. The HC and CO emissions decrease while NO(x) and NO(2) emissions increase. The smoke opacity and particulate mass concentrations reduce significantly at high engine load. In addition, for submicron particles, the geometry mean diameter of the particles becomes smaller while the total number concentration increases. For the unregulated gaseous emissions, generally, the emissions of formaldehyde, 1,3-butadiene, toluene, xylene decrease, however, acetaldehyde and benzene emissions increase. The results indicate that the combination of ultra-low sulfur diesel and biodiesel from waste cooking oil gives similar results to those in the literature using higher sulfur diesel fuels and biodiesel from other sources.

Poverty, energy, and resource use in developing countries: focus on Africa.

Energy poverty affects poor communities and poor nations far more severely, and more directly, than in developed nations. Poor rural communities are particularly vulnerable, and the poor globally spend by far the largest percentage of income on energy. To make matters worse, record-high oil prices combined with sharp decline in foreign exchange earnings are key processes influencing the energy sector in Africa. These increases cause tremendous local hardships, but can be used to steer development decisions toward renewable energy technologies. At the same time, breaking up of public monopolies and liberalizing generation and distribution provides an opportunity for a new approach to rural electrification. Given the right incentives and institutional framework, a new set of players (e.g., private entrepreneurs, cooperatives, nongovernmental organizations, and communities) are likely to emerge and dominate reformed rural electricity markets in the future. Through technological and institutional "leap-frogging," Africa stands to gain significantly by augmenting current initiatives with experience and lessons recently gained in South Asia and Latin America. In these regions, a number of remarkable recent strides to seed and grow rural electricity markets while stimulating and encouraging private investments. Examples of innovative regulatory tools to address poverty include licensing, standards and guidelines, metering, tariffs, transmission charges, and performance-based contracting for energy services.