[Monograph for N-Methyl-pyrrolidone (NMP) and human biomonitoring values for the metabolites 5-Hydroxy-NMP and 2-Hydroxy-N-methylsuccinimide]. / Stoffmonographie für N-Methyl-2-pyrrolidon (NMP) und "Human-Biomonitoring"-Werte für die Metaboliten 5-Hydroxy-NMP und 2-Hydroxy-N-methylsuccinimid im Urin von Erwachsenen und Kindern : Stellungnahme der Kommission "Human-Biomonitoring" des Umweltbundesamtes.

1-Methyl-pyrrolidone (NMP) is used as a solvent in many technical applications. The general population may be exposed to NMP from the use as ingredient in paint and graffiti remover, indoors also from use in paints and carpeting. Because of developmental toxic effects, the use of NMP in consumer products in the EU is regulated. The developmental effects accompanied by weak maternally toxic effects in animal experiments are considered as the critical effects by the German HBM Commission. Based on these effects, HBM-I values of 10 mg/l urine for children and of 15 mg/l for adults, respectively, were derived for the metabolites 5-Hydroxy-NMP and 2-Hydroxy-N-methylsuccinimide. HBM-II-values were set to 30 mg/l urine for children and 50 mg/l for adults, respectively. Because of similar effects of the structural analogue 1-ethyl-2-pyrrolidone (NEP), the possible mixed exposure to both compounds has to be taken into account when evaluating the total burden.

Sensitive and selective liquid chromatography-tandem mass spectrometry method for the quantification of aniracetam in human plasma.

A rapid, sensitive and selective LC-MS/MS method was developed and validated for the quantification of aniracetam in human plasma using estazolam as internal standard (IS). Following liquid-liquid extraction, the analytes were separated using a mobile phase of methanol-water (60:40, v/v) on a reverse phase C18 column and analyzed by a triple-quadrupole mass spectrometer in the selected reaction monitoring (SRM) mode using the respective [M+H]+ ions, m/z 220-->135 for aniracetam and m/z 295-->205 for the IS. The assay exhibited a linear dynamic range of 0.2-100 ng/mL for aniracetam in human plasma. The lower limit of quantification (LLOQ) was 0.2 ng/mL with a relative standard deviation of less than 15%. Acceptable precision and accuracy were obtained for concentrations over the standard curve range. The validated LC-MS/MS method has been successfully applied to study the pharmacokinetics of aniracetam in healthy male Chinese volunteers.

International Conference on Harmonisation; final recommendations on the revision of the permitted daily exposures for two solvents, n-methylpyrrolidone and tetrahydrofuran, according to the maintenance procedures for the guidance Q3C Impurities: Residual Solvents; Availability. Notice.

The Food and Drug Administration (FDA) is announcing final recommendations to revise the permitted daily exposures (PDEs) for two solvents, n-methylpyrrolidone (NMP) and tetrahydrofuran (THF), according to the maintenance procedures for the guidance for industry entitled "Q3C Impurities: Residual Solvents." The final recommendations were reached under the auspices of the International Conference on Harmonisation of Technical Requirements for Registration of Pharmaceuticals for Human Use (ICH).

BOP: biocompatible osteoconductive polymer: an experimental approach.

BOP (biocompatible osteoconductive polymer) is a material proposed for osteosyntheses and for filling of bone defects in orthopaedics, neurosurgery and stomatology. It is a composite made of a copolymer of N-vinylpyrrolidone and methylmethacrylate, of polyamide-6 fibers and of calcium gluconate. The histological investigation includes the study of 30 intact rabbit femurs instrumented with a BOP rod, as well as the study of organs of the reticuloendothelial system. The currently available results show the absence of toxicity on hematopoietic tissue. Zones of osteoblastic activity surround the rods, coupled with an osteoclastic reaction which may result in the partial fragmentation of the polyamide fibers and its incorporation in the newly formed bone. We also observed the encapsulation of the material. The biomechanical approach investigated the mechanical properties of the material in bending and in shear. The radiological aspects of the investigation consisted of computerized axial tomography of the implanted femurs to measure density at the bone-implant interface.