Effect of DNA sizes and reactive oxygen species on degradation of sulphonamide resistance sul1 genes by combined UV/free chlorine processes.

Nowadays, antibiotic resistance genes (ARGs) have been characterized as an emerging environmental contaminant, as the spread of ARGs may increase the difficulty of bacterial infection treatments. This study evaluates the combination of ultraviolet (UV) irradiation and chlorination, the two most commonly applied disinfection methods, on the degradation of sulphonamide resistance sul1 genes. The results revealed that although both of individual UV and chlorination processes were relatively less effective, two of the four combined processes, namely UV followed by chlorination (UV-Cl2) and simultaneous combination of UV and chlorination (UV/Cl2), delivered a better removal rate (up to 1.5 logs) with an observation of synergetic effects up to 0.609 log. The mechanisms analysis found that the difference of DNA size affected sul1 genes degradation by UV and chlorination; targeted genes on larger DNA fragments could be more effectively degraded by UV (1.09 logs for large fragments and 0.12 log for small fragments when UV dose reached 432 mJ/cm2), while to degrade ARGs on smaller DNA fragments required less free chlorine dosage (10 mg/L for small fragments and 40 mg/L for large fragments). The sequential combination of UV and chlorination (UV-Cl2) used the corresponding reactivity of both processes, which could be the reason for the synergetic effect. For UV/Cl2 process, the formation of reactive oxygen species (ROS) contributed to the synergetic effect. Scavenger analysis showed that the contribution of ROS to the sul1 gene reduction was 0.004 to 0.273 log (up to 45.5 % of the total synergy values), and among the two major reactive species in UV/Cl2 system, HO was the more important radical, while the contribution of Cl was negligible. Besides, UV/Cl2 process also used the corresponding reactivity of both processes to generate the remaining synergy values when excluding the contribution by reactive radicals. These findings provide a thorough understanding of the effects of UV and free chlorine on the degradation of ARGs and indicate the potential to utilize the combined processes of UV and free chlorine in water or wastewater treatment practice to control the dissemination of antibiotic resistance.

Degradation of cyanotoxin microcystin-LR in synthetic and natural waters by chemical-free UV/VUV radiation.

This study investigated the capability of ultraviolet radiation at 254 nm and 185 nm (UV/VUV) to degrade cyanotoxin microcystin-LR (MC-LR). Results showed 70% toxin reduction solely by 254 nm direct photolysis (ε254 = 13,225 ±â€¯814 M-1cm-1; Φ254 = 0.29 ±â€¯0.03 mol/Einstein). The addition of 185 nm increased MC-LR degradation through advanced oxidation by •OH (k•OH,MC-LR = 2.25 ±â€¯0.39 × 1010 M-1s-1). Alkalinity and organics (DOC) reduced MC-LR degradation by scavenging •OH (kobs,MilliQ = 0.117 cm2/mJ; kobs,50ppmAlk. = 0.0497 cm2/mJ; kobs,6ppmDOC = 0.019 cm2/mJ). Chloride absorbed 185 nm, impacting •OH formation and generating Cl•, while also scavenging •OH. However, Cl• is reactive and •OH scavenging is reversible, resulting in relatively low impact on MC-LR degradation (kobs,50ppmCl = 0.0939 cm2/mJ). In natural water, MC-LR could be degraded from a typical concentration (˜15 µg/L) to below detection (<0.5 µg/L) with a UV254 fluence of 200 mJ/cm2 using UV/VUV. The presence of cyanobacterial cells impeded MC-LR degradation; however, 90% MC-LR degradation could still be achieved. UV/VUV is a promising chemical-free technology capable of MC-LR degradation in a variety of water conditions, and a potentially suitable treatment option for small, remote communities.

Plasmonic Ag decorated graphitic carbon nitride sheets with enhanced visible-light response for photocatalytic water disinfection and organic pollutant removal.

Photocatalytic disinfection with high performance is thought to be a promising way for water purification. Herein, plasmonic Ag doped urea-derived graphitic carbon nitride (g-C3N4) composites were fabricated via in-situ photo-deposition at room temperature as the visible-light photocatalyst. Scan electron microscopy and transmission electron microscopy images showed the uniform dispersion of Ag nanoparticles on the surface of g-C3N4 sheet, which facilitated the synergistic effect of antibacterial performance from Ag and photocatalytic property from Ag/g-C3N4 composites. Photocatalytic water disinfection against Escherichia coli with visible light was performed to demonstrate the improved photocatalytic property with assistance of Ag. The 3-Ag/g-C3N4 exhibited the best bactericidal performance by inactivating all bacteria within 120 min with damaged cell membranes of Escherichia coli observed by scan electron microscopy and transmission electron microscopy images. Photoluminescence spectra, steady-state surface photovoltage spectra, photocurrent response, and electrochemical impedance spectra results revealed that Ag nanoparticles inhibited the recombination of photo-generated e- and h+ pairs and further reinforced the photocatalytic performance of g-C3N4. Scavenger experiments indicated that h+ produced on valence band of g-C3N4 dominated the photocatalytic disinfection process against Escherichia coli. This work further proved Ag/g-C3N4 showed great potential in photocatalytic water disinfection under visible-light irradiation.

Thinking Outside the Treatment Plant: UV for Water Distribution System Disinfection.

This work critically evaluates the current paradigm of water distribution system management and juxtaposes that with the potential benefits of employing UV irradiation, which we hope will catalyze a judicial re-evaluation of the current practices in water distribution system management and spur critical research and a new way of thinking about secondary disinfection across the extent of distribution systems. Given the recent advances in UV technology and the efficacy of UV disinfection against all pathogen classes, we now see UV applications for disinfection in many aspects of consumers lives: in water coolers, dishwashers, coffee makers, and disinfection of personal items like gym bags, water bottles, and toothbrushes. Public and regulatory concern over water quality and pathogens, especially the recent interest in building plumbing, calls out for new approaches to disinfection and distribution system management. We envision a new model for secondary disinfection in water distribution systems utilizing emerging germicidal UV LED-based disinfection. UV irradiation in water treatment can achieve high levels of disinfection of all pathogens and minimize or eliminate the formation of regulated disinfection byproducts. So why is UV not considered as a secondary disinfectant for distribution systems? In this Account, we lay out the logic as to the benefits and practicality of adding distributed UV treatment to assist in protection of distribution systems and protect water quality for human exposure. The possible locations of UV irradiation in distribution systems are envisioned, potentially including UV booster stations along the distribution network, UV in storage tanks or their inlet/outlets, LEDs distributed along pipe walls, small point of use/entry treatment systems for buildings/homes/taps, or submersible swimming or rolling UV LED drones to reach problem pipes and provide a "shock" treatment or provide sterilization after main breaks or repairs. The benefits of UV applications in water also include high effectiveness against chlorine-resistant protozoa, no added disinfection byproducts, and compatibility of adding of UV to existing secondary disinfection strategies for enhanced protection. Potential challenges and research needs are described, such as use of UV-compatible pipe materials, implementation of sensors to monitor distributed LEDs, management of waste heat from the rear surface of the LED, and understanding the potential for regrowth of opportunistic microorganisms. Another notable challenge is the relatively stagnant regulatory environment in some countries to develop frameworks for evaluation and acceptance of UV technology in distribution systems that require a chemical secondary disinfectant. Rapid advances in UV LED research has propelled the growth of this field, but needs still remain, including understanding behavior of biofilms in pipes under UV irradiation, including any beneficial effects that may be lost, the potential for fouling of LED emission surfaces and monitoring points, and provision of a distributed power network to run the LEDs. Regulators may want specific monitoring approaches and advances in real-time monitoring of microbial viability, and engineers may need to develop new approaches to overall management.

Photocatalytic removal of phenanthrene and algae by a novel Ca-Ag3PO4 composite under visible light: Reactivity and coexisting effect.

In this study, the feasibility of a novel Ca-Ag3PO4 composite with visible light irradiation for the phenanthrene (PHE) degradation and algae inactivation in artificial seawater was firstly investigated. The experimental findings revealed that Ag3PO4 phase was sucessfully formed on the Ca-based material, and the presence of Ca-based material could effectively keep Ag3PO4 particles stable. An excellent performance on PHE degradation or algae inactivation was observed from Ca-Ag3PO4 composite under visible light irradiation. The degradation of PHE or inactivation of algae not only could be efficiently achieved in the single mode, but also could be successfully achieved in the coexisting mode. Above 96% of PHE and algae were simultaneously removed within 12 h in the Ca-Ag3PO4/visible light system. It was further observed that the degradation of PHE and/or inactivation of algae increased with the increase of Ca-Ag3PO4 dosage. HO was the primary radical responsible for PHE degradation, whereas HO and Ag+ released from Ca-Ag3PO4 mainly contributed to the algae inactivation. A possible mechanism involving the catalytic removal of PHE and algae by Ca-Ag3PO4 under visible light irradiation was proposed. This study provides helpful guide for the simultaneous removal of various pollutants in real seawater.

Impact of UVA pre-radiation on UVC disinfection performance: Inactivation, repair and mechanism study.

Ultraviolet (UV) light emission diode (LED), which is mercury free and theoretically more energy efficient, has now become an alternative to conventional UV lamps in water disinfection industry. In this research, the disinfection performance of a novel sequential process, UVA365nm LED followed by UVC265nm LED (UVA-UVC), was evaluated. The results revealed that the responses of different bacterial strains to UVA-UVC varied. Coupled with appropriate dosages of UVC, a 20 min UVA pre-radiation provided higher inactivations (log inactivation) of E. coli ATCC 11229, 15597 and 700891 by 1.2, 1.4 and 1.2 times, respectively than the sum of inactivations by UVA alone and UVC alone. On the contrary, the inactivation of E. coli ATCC 25922, the most UVC sensitive strain, decreased from 3 log to 1.8 log after UVA pre-radiation. A 30 min UVA pre-radiation did not affect the photo repair capacity of the four strains (n = 23, p > 0.1), but their dark repair ability was significantly inhibited (n = 14, p < 0.05). Mechanism study was conducted for two representative strains, E. coli ATCC 15597 and 25922 to understand the observed effect. The hypothesis that UVA pre-radiation promoted the yield of reactive oxygen species (ROS) was rejected. ELISA results indicated that 18% more cyclobutane pyrimidine dimers (CPD) were formed in E. coli ATCC 15597 with UVA pre-radiation (n = 3, p < 0.01), however, the CPD levels of E. coli ATCC 25922 was the same with or without UVA pre-radiation (n = 3, p > 0.01). Considering the results of both dark repair and CPD formation, it was concluded that the increased UV sensitivity of E. coli 15597 was originated from the increased CPD. For E. coli ATCC 25922, the enhanced UV resistance was attributed to the strain's adoption of a survival strategy, translesion DNA synthesis (TLS), when triggered by UVA pre-radiation. The study on UmuD protein, which is a key protein during TLS, confirmed this hypothesis.

Metal-free virucidal effects induced by g-C3N4 under visible light irradiation: Statistical analysis and parameter optimization.

Waterborne viruses with a low infectious dose and a high pathogenic potential pose a serious risk for humans all over the world, calling for a cost-effective and environmentally-friendly inactivation method. Optimizing operational parameters during the disinfection process is a facile and efficient way to achieve the satisfactory viral inactivation efficiency. Here, the antiviral effects of a metal-free visible-light-driven graphitic carbon nitride (g-C3N4) photocatalyst were optimized by varying operating parameters with response surface methodology (RSM). Twenty sets of viral inactivation experiments were performed by changing three operating parameters, namely light intensity, photocatalyst loading and reaction temperature, at five levels. According to the experimental data, a semi-empirical model was developed with a high accuracy (determination coefficient R2 = 0.9908) and then applied to predict the final inactivation efficiency of MS2 (a model virus) after 180 min exposure to the photocatalyst and visible light illumination. The corresponding optimal values were found to be 199.80 mW/cm2, 135.40 mg/L and 24.05 °C for light intensity, photocatalyst loading and reaction temperature, respectively. Under the optimized conditions, 8 log PFU/mL of viruses could be completely inactivated by g-C3N4 without regrowth within 240 min visible light irradiation. Our study provides not only an extended application of RSM in photocatalytic viral inactivation but also a green and effective method for water disinfection.

Disinfection of the Water Borne Pathogens Escherichia coli and Staphylococcus aureus by Solar Photocatalysis Using Sonochemically Synthesized Reusable Ag@ZnO Core-Shell Nanoparticles.

Water borne pathogens present a threat to human health and their disinfection from water poses a challenge, prompting the search for newer methods and newer materials. Disinfection of the Gram-negative bacterium Escherichia coli and the Gram-positive coccal bacterium Staphylococcus aureus in an aqueous matrix was achieved within 60 and 90 min, respectively, at 35 °C using solar-photocatalysis mediated by sonochemically synthesized Ag@ZnO core-shell nanoparticles. The efficiency of the process increased with the increase in temperature and at 55 °C the disinfection for the two bacteria could be achieved in 45 and 60 min, respectively. A new ultrasound-assisted chemical precipitation technique was used for the synthesis of Ag@ZnO core-shell nanoparticles. The characteristics of the synthesized material were established using physical techniques. The material remained stable even at 400 °C. Disinfection efficiency of the Ag@ZnO core-shell nanoparticles was confirmed in the case of real world samples of pond, river, municipal tap water and was found to be better than that of pure ZnO and TiO2 (Degussa P25). When the nanoparticle- based catalyst was recycled and reused for subsequent disinfection experiments, its efficiency did not change remarkably, even after three cycles. The sonochemically synthesized Ag@ZnO core-shell nanoparticles thus have a good potential for application in solar photocatalytic disinfection of water borne pathogens.

Photoelectrocatalytic inactivation of fecal coliform bacteria in urban wastewater using nanoparticulated films of TiO2 and TiO2/Ag.

Photocatalysis has shown the ability to inactivate a wide range of harmful microorganisms with traditional use of chlorination. Photocatalysis combined with applied bias potential (photoelectrocatalysis) increases the efficiency of photocatalysis and decreases the charge recombination. This work examines the inactivation of fecal coliform bacteria present in real urban wastewater by photoelectrocatalysis using nanoparticulated films of TiO2 and TiO2/Ag (4%w/w) under UV light irradiation. The catalysts were prepared with different thicknesses by the sol-gel method and calcined at 400°C and 600°C. The urban wastewater samples were collected from the sedimentation tank effluent of the university sewage treatment facility. The rate of bacteria inactivation increases with increasing the applied potential and film thicknesses; also, the presence of silver on the catalyst surface annealed at 400°C shows better inactivation than that at 600°C. Finally, a structural cell damage of Escherichia coli (DH5α), inoculated in water, is observed during the photoelectrocatalytic process.

Impact of ozonation, anion exchange resin and UV/H2O2 pre-treatments to control fouling of ultrafiltration membrane for drinking water treatment.

The effects of ozonation, anion exchange resin (AER) and UV/H2O2 were investigated as a pre-treatment to control organic fouling (OF) of ultrafiltration membrane in the treatment of drinking water. It was found that high molecular weight (MW) organics such as protein and polysaccharide substances were majorly responsible for reversible fouling which contributed to 90% of total fouling. The decline rate increased with successive filtration cycles due to deposition of protein content over time. All pre-treatment could reduce the foulants of a Ultrafiltration membrane which contributed to the improvement in flux, and there was a greater improvement of flux by UV/H2O2 (61%) than ozonation (43%) which in turn was greater than AER (23%) treatment. This was likely due to the effective removal/breakdown of high MW organic content. AER gave greater removal of biofouling potential components (such as biodegradable dissolved organic carbon and assimilable organic carbon contents) compared to UV/H2O2 and ozonation treatment. Overall, this study demonstrated the potential of pre-treatments for reducing OF of ultrafiltration for the treatment of drinking water.

Linking optical properties of dissolved organic matter to multiple processes at the coastal plume zone in the East China Sea.

Because of the significance in photosynthesis, nutrient dynamics, trophodynamics and biological activity, dissolved organic matter (DOM) is important to the microbial community in the coastal plume zone. In this study, we investigated the hydrodynamic processes, photodegradation and biodegradation of DOM at the Yangtze River plume in the East China Sea through analyzing water quality and optical properties of DOM. Surface water samples were collected to examine water quality and fluorescence properties of fluorescent dissolved organic matter (FDOM). The results indicated that dilution was the key factor in the multiple processes, and the mixing process gradually increased from nearshore to offshore in coastal water. Four components of FDOM representing humic-like substances (C1 & C4) and protein-like substances (C2 & C3) were identified, and all components showed nearly conservative behaviors. Protein-like substances were more mutable compared to humic-like substances. The photodegradation of humic-like substances caused brown algae blooms to some extent. The molecular weight of humic substances gradually decreased along the mixing process. FDOM in the plume zone was both of terrigenous and autochthonous origins, and the characteristic of terrigenous origin was obvious compared to that of autochthonous origin.

Identification of ultraviolet transformation products of diclofenac by means of liquid chromatography and mass spectrometry.

The removal of the anti-inflammatory drug diclofenac, which can be determined in concentrations up to 1µg/mL in the aquatic environment, from water samples by the use of UV light is investigated by liquid chromatography/mass spectrometry (LC/MS). It is very important to find out whether diclofenac is fully mineralized into non-toxic products or if the UV treatment leads to other potentially bioactive products. The irradiation of an aqueous solution of diclofenac with light in the wavelength range of 220nm-500nm provides a fast degradation of diclofenac in less than four minutes. Eleven transformation products have been detected by means of reversed-phase LC/MS, seven of which have not been described in literature before. Fragmentation experiments allowed their characterization and lead to proposed structures for most of them. Some of the structures may explain the increased toxicity, which was observed after irradiation of diclofenac solution by other groups.

UV disinfection and flocculation-chlorination sachets to reduce hepatitis E virus in drinking water.

Hepatitis E Virus (HEV) is a major cause of waterborne outbreaks in areas with poor sanitation. As safe water supplies are the keystone for preventing HEV outbreaks, data on the efficacy of disinfection treatments are urgently needed. Here, we evaluated the ability of UV radiation and flocculation-chlorination sachets (FCSs) to reduce HEV in water matrices. The HEV-p6-kernow strain was replicated in the HepG2/C3A cell line, and we quantified genome number using qRT-PCR and infectivity using an immunofluorescence assay (IFA). UV irradiation tests using low-pressure radiation showed inactivation kinetics for HEV of 99.99% with a UV fluence of 232J/m(2) (IC 95%, 195,02-269,18). Moreover, the FCSs preparations significantly reduced viral concentrations in both water matrices, although the inactivation results were under the baseline of reduction (4.5 LRV) proposed by WHO guidelines.

Disinfection of an advanced primary effluent using peracetic acid or ultraviolet radiation for its reuse in public services.

The disinfection of a continuous flow of an effluent from an advanced primary treatment (coagulation-flocculation-sedimentation) with or without posterior filtration, using either peracetic acid (PAA) or ultraviolet (UV) radiation was studied. We aimed to obtain bacteriological quality to comply with the microbiological standard established in the Mexican regulations for treated wastewater reuse (NOM-003-SEMARNAT-1997), i.e., less than 240 MPN (most probable number) FC/100 mL. The concentrations of PAA were 10, 15, and 20 mg/L, with contact times of 10, and 15 min. Fecal coliforms (FC) inactivation ranged from 0.93 up to 6.4 log units, and in all cases it reached the limits set by the mentioned regulation. Water quality influenced the PAA disinfection effectiveness. An efficiency of 91% was achieved for the unfiltered effluent, as compared to 99% when wastewater was filtered. UV radiation was applied to wastewater flows of 21, 30 and 39 L/min, with dosages from 1 to 6 mJ/cm². This treatment did not achieve the bacteriological quality required for treated wastewater reuse, since the best inactivation of FC was 1.62 log units, for a flow of 21 L/min of filtered wastewater and a UV dosage of 5.6 mJ/cm².

Tertiary treatment for wastewater reuse based on the Daphnia magna filtration - comparison with conventional tertiary treatments.

Tertiary treatments are required to permit safe reuse of wastewater. The performance of a new biological tertiary treatment based on the filtration by a population of Daphnia magna was studied and compared with the performance of other conventional tertiary treatments such as coagulation-flocculation, settling tank, disc filtration, sand filtering and ultraviolet (UV) light. The analysis was based on the efficiency in the particle removal and Escherichia coli inactivation. The Daphnia magna treatment reduced the concentration of particles with diameters below 30 µm by 35%, depending on abiotic parameters such as water temperature and the hydraulic retention time (HRT). The Daphnia magna filtration increased with water temperature for water temperatures >20 °C, while it remained constant for water temperatures <20 °C. Lower HRTs induced the growth of the Daphnia magna population, maintaining the same water quality. Furthermore, the Daphnia magna treatment inactivated E. coli in 1.2 log units. This inactivation was six times larger than that obtained by the conventional macrofiltration systems analyzed, although lower than the inactivation attained by UV light, which ranged between 1.5 and 4 log units.

Cost-effectiveness analysis of TOC removal from slaughterhouse wastewater using combined anaerobic-aerobic and UV/H2O2 processes.

The objective of this study is to evaluate the operating costs of treating slaughterhouse wastewater (SWW) using combined biological and advanced oxidation processes (AOPs). This study compares the performance and the treatment capability of an anaerobic baffled reactor (ABR), an aerated completely mixed activated sludge reactor (AS), and a UV/H2O2 process, as well as their combination for the removal of the total organic carbon (TOC). Overall efficiencies are found to be up to 75.22, 89.47, 94.53, 96.10, 96.36, and 99.98% for the UV/H2O2, ABR, AS, combined AS-ABR, combined ABR-AS, and combined ABR-AS-UV/H2O2 processes, respectively. Due to the consumption of electrical energy and reagents, operating costs are calculated at optimal conditions of each process. A cost-effectiveness analysis (CEA) is performed at optimal conditions for the SWW treatment by optimizing the total electricity cost, H2O2 consumption, and hydraulic retention time (HRT). The combined ABR-AS-UV/H2O2 processes have an optimal TOC removal of 92.46% at an HRT of 41 h, a cost of $1.25/kg of TOC removed, and $11.60/m(3) of treated SWW. This process reaches a maximum TOC removal of 99% in 76.5 h with an estimated cost of $2.19/kg TOC removal and $21.65/m(3) treated SWW, equivalent to $6.79/m(3) day.

Evaluating UV/H2O2, UV/percarbonate, and UV/perborate for natural organic matter reduction from alternative water sources.

Natural organic matter (NOM) continues to increase in drinking water sources due to many factors, including changes in land use and global climate. Water treatment facilities will need to evaluate the best treatment options to account for these higher NOM levels. The UV/H2O2 advanced oxidation process (AOP) is one treatment option that has shown success at reducing high levels of NOM. As a result, this study evaluated the UV/H2O2 for the reduction of NOM in a high NOM water matrix, the Florida Everglades. In addition to liquid H2O2, sodium percarbonate and sodium perborate were used as oxidants to evaluate their performance as alternatives to liquid H2O2. Results showed that all three oxidants were able to reduce aromatic carbon (UV254) by 46-66% and dissolved organic carbon (DOC) by 11-19% at UV fluences of 2.6-2.7 J cm(-2) and an H2O2 dose of 100 mg L(-1). When the UV fluences were increased to 21.8-26.1 J cm(-2) at an H2O2 dose of 100 mg L(-1), UV254 reduction increased to 79-97% and DOC to 42-82% for all three oxidants. All three oxidants performed statistically similar for UV254 reduction. However, for DOC reduction, H2O2 performed statically better than both percarbonate and perborate, and perborate performed statistically better than percarbonate. While the UV/H2O2 AOP is effective for NOM reduction in high NOM waters, advances in electrical efficiency are needed to make it economically feasible.

Treatment of winery wastewater by electrochemical methods and advanced oxidation processes.

The aim of this research was development of new system for the treatment of highly polluted wastewater (COD = 10240 mg/L; SS = 2860 mg/L) originating from vine-making industry. The system consisted of the main treatment that included electrochemical methods (electro oxidation, electrocoagulation using stainless steel, iron and aluminum electrode sets) with simultaneous sonication and recirculation in strong electromagnetic field. Ozonation combined with UV irradiation in the presence of added hydrogen peroxide was applied for the post-treatment of the effluent. Following the combined treatment, the final removal efficiencies of the parameters color, turbidity, suspended solids and phosphates were over 99%, Fe, Cu and ammonia approximately 98%, while the removal of COD and sulfates was 77% and 62%, respectively. A new approach combining electrochemical methods with ultrasound in the strong electromagnetic field resulted in significantly better removal efficiencies for majority of the measured parameters compared to the biological methods, advanced oxidation processes or electrocoagulation. Reduction of the treatment time represents another advantage of this new approach.

Point-of-use water disinfection using UV light-emitting diodes to reduce bacterial contamination.

The treatment process described in this research explores the impact of exposing water samples containing fecal coliforms to the radiation produced by single ultraviolet (UV) light-emitting diodes (LEDs) operating at 265 nm. UV LEDs are long lasting, compact in size and produce more efficient light output than traditional mercury-vapour bulbs, making them ideal for application in point-of-use disinfection systems, such as in remote areas. In this study, contaminated water samples containing either a pure culture of Escherichia coli or tertiary effluent from the City of Regina Wastewater Treatment Plant were used to study the application and efficiency of using UV LEDs for water disinfection. The results indicate that bacterial inactivation was achieved in a time-dependent manner, with 1- and 2.5-log E. coli reductions in water following 20 and 50 min of UV LED exposure, respectively. Ultraviolet radiation was less effective in reducing coliform bacteria in wastewater samples due to the elevated turbidity levels. Further work remains to be completed to optimize the application of UV LEDs for point-of-use disinfection systems; however, the results from this study support that bacterial inactivation using UV LEDs is possible, meriting further future technological development of the LEDs.

Multifunctional Fe3O4 nanoparticles for highly sensitive detection and removal of Al(III) in aqueous solution.

Fe(3)O(4) nanoparticles (NPs) decorated with rhodamine 6G Schiff base, which exhibit high selectivity and sensitivity toward Al(3+) over other common metal ions in aqueous media under a physiological pH window via a 1:1 binding mode, have been synthesized and characterized. The resulting conjugate renders the rhodamine 6G Schiff base unit more water soluble, and the detection limit reaches 0.3 ppb in water. Moreover, can detect Al(3+) in a wide pH span (5.0-11.0) and enrich/remove excess Al(3+) in water via an external magnetic field, which indicates that it has more potential and further practical applications for biology and toxicology. Furthermore, provides good fluorescent imaging of Al(3+) in living cells.