Photocatalytic degradation of dimethoate in Bok choy using cerium-doped nano titanium dioxide.

Dimethoate, a systemic insecticide, has been used extensively in vegetable production. Insecticide residues in treated vegetables, however, pose a potential risk to consumers. Photocatalytic degradation is a new alternative to managing pesticide residues. In this study, the degradation of dimethoate in Bok choy was investigated under the field conditions using cerium-doped nano titanium dioxide (TiO2/Ce) hydrosol as a photocatalyst. The results show that TiO2/Ce hydrosol can accelerate the degradation of dimethoate in Bok choy. Specifically, the application of TiO2/Ce hydrosol significantly increased the reactive oxygen species (ROS) contents in the treated Bok choy, which speeds up the degradation of dimethoate. Ultra-performance liquid chromatography coupled with mass spectrometry (UPLC-MS) analysis detected three major degradation products, including omethoate, O,O,S-trimethyl thiophosphorothioate, and 1,2-Bis (acetyl-N-methyl-) methane disulfide. Two potential photodegradation pathways have been proposed based on the intermediate products. To understand the relationship between photodegradation and the molecular structure of target insecticides, we investigated the bond length, Mulliken atomic charge and frontier electron density of dimethoate using ab initio quantum analysis. These results suggest the P = S, P-S and S-C of dimethoate are the initiation sites for the photocatalytic reaction in Bok choy, which is consistent with our empirical data.

Determination of carbamate and organophosphorus pesticides in vegetable samples and the efficiency of gamma-radiation in their removal.

In the present study, the residual pesticide levels were determined in eggplants (Solanum melongena) (n = 16), purchased from four different markets in Dhaka, Bangladesh. The carbamate and organophosphorus pesticide residual levels were determined by high performance liquid chromatography (HPLC), and the efficiency of gamma radiation on pesticide removal in three different types of vegetables was also studied. Many (50%) of the samples contained pesticides, and three samples had residual levels above the maximum residue levels determined by the World Health Organisation. Three carbamates (carbaryl, carbofuran, and pirimicarb) and six organophosphates (phenthoate, diazinon, parathion, dimethoate, phosphamidon, and pirimiphos-methyl) were detected in eggplant samples; the highest carbofuran level detected was 1.86 mg/kg, while phenthoate was detected at 0.311 mg/kg. Gamma radiation decreased pesticide levels proportionately with increasing radiation doses. Diazinon, chlorpyrifos, and phosphamidon were reduced by 40-48%, 35-43%, and 30-45%, respectively, when a radiation strength of 0.5 kGy was utilized. However, when the radiation dose was increased to 1.0 kGy, the levels of the pesticides were reduced to 85-90%, 80-91%, and 90-95%, respectively. In summary, our study revealed that pesticide residues are present at high amounts in vegetable samples and that gamma radiation at 1.0 kGy can remove 80-95% of some pesticides.

Degradation of imidacloprid containing wastewaters using ultrasound based treatment strategies.

The present work deals with application of sonochemical reactors for the treatment of imidacloprid containing wastewaters either individually or in combination with other advanced oxidation processes. Experiments have been performed using two different configurations of sonochemical reactors viz. ultrasonic horn (20 kHz frequency and rated power of 240 W) and ultrasonic bath equipped with radially vibrating horn (25 kHz frequency and 1 kW rated power). The work also investigates the effect of addition of process intensifying agents such as H2O2 and CuO, which can enhance the production of free radicals in the system. The combination studies with advanced oxidation process involve the advanced Fenton process and combination of ultrasound with UV based oxidation. The extent of degradation obtained using combination of US and H2O2 at optimum loading of H2O2 was found to be 92.7% whereas 96.5% degradation of imidacloprid was achieved using the combination of US and advanced Fenton process. The process involving the combination of US, UV and H2O2 was found to be the best treatment approach where complete degradation of imidacloprid was obtained with 79% TOC removal. It has been established that the use of cavitation in combination with different oxidation processes can be effectively used for the treatment of imidacloprid containing wastewater.

Degradation of imidacloprid using combined advanced oxidation processes based on hydrodynamic cavitation.

The harmful effects of wastewaters containing pesticides or insecticides on human and aquatic life impart the need of effectively treating the wastewater streams containing these contaminants. In the present work, hydrodynamic cavitation reactors have been applied for the degradation of imidacloprid with process intensification studies based on different additives and combination with other similar processes. Effect of different operating parameters viz. concentration (20-60 ppm), pressure (1-8 bar), temperature (34 °C, 39 °C and 42 °C) and initial pH (2.5-8.3) has been investigated initially using orifice plate as cavitating device. It has been observed that 23.85% degradation of imidacloprid is obtained at optimized set of operating parameters. The efficacy of different process intensifying approaches based on the use of hydrogen peroxide (20-80 ppm), Fenton's reagent (H2O2:FeSO4 ratio as 1:1, 1:2, 2:1, 2:2, 4:1 and 4:2), advanced Fenton process (H2O2:Iron Powder ratio as 1:1, 2:1 and 4:1) and combination of Na2S2O8 and FeSO4 (FeSO4:Na2S2O8 ratio as 1:1, 1:2, 1:3 and 1:4) on the extent of degradation has been investigated. It was observed that near complete degradation of imidacloprid was achieved in all the cases at optimized values of process intensifying parameters. The time required for complete degradation of imidacloprid for approach based on hydrogen peroxide was 120 min where as for the Fenton and advance Fenton process, the required time was only 60 min. To check the effectiveness of hydrodynamic cavitation with different cavitating devices, few experiments were also performed with the help of slit venturi as a cavitating device at already optimized values of parameters. The present work has conclusively established that combined processes based on hydrodynamic cavitation can be effectively used for complete degradation of imidacloprid.

Using mass spectrometry to highlight structures of degradation compounds obtained by photolysis of chloroacetamides: case of acetochlor.

The photooxidation of acetochlor (a pesticide belonging to the acetamides group) using a polychromatic UV irradiation in ultrapure water was studied. This study reports the efficiency of mass spectrometry for the characterization of photodegradation products of acetochlor. Decompositions of protonated ions MH+are proposed in electrospray (ESI) mode for LC­MS, while electron ionization (EI) and chemical ionization modes (CI) are used for GC­MS. The knowledge of fragmentation and the use of a combination of experiments (MS/MS, high resolution) allow the characterization of photoproducts. Structural elucidation is assisted by the use of photolysed deuterated compounds. Fifteen major degradation products have been characterized, five by LC-QTOF, six photoproducts by GC-ITMS, and four are observed by both techniques. In vitro bioassays based on the quantification of receptor-mediated activity demonstrated that acetochlor photolysis engenders a moderate but significant estrogenic activity. Moreover, a quantitative structure­activity relationship (QSAR) approach was used to assess the potential toxicity effect of acetochlor and its by-products. The predictions were analyzed showing a variety of toxicity profiles of acetochlor photoproducts depending on the toxicological investigated endpoint.

Ultrasonic destruction of pesticide contaminants in slurries.

The use of high power ultrasound to destroy pesticide contaminants in sand slurries is reported. Small quantities of DDT, chlordane, atrazine, 2,4,5-T and endosulfan in solvent were added to washed, screened sand and deposited onto the sand by slow evaporation of the solvent. Fifty wt.% slurries for all five pesticides and 20 wt.% slurries of atrazine and 2,4,5-T were sonicated for periods up to 30 min and samples were withdrawn at various intervals and analysed to follow the kinetics of contaminant destruction. Seventy percent destruction of the contaminant was obtained for four of the 50 wt.% slurries with approximately 50% destruction of 2,4,5-T in 10 min of sonication whereas, in the 20 wt.% slurries of atrazine and 2,4,5-T, and 75% and 85% reduction, respectively, was obtained in 10 min. We postulate that better stirring of the slurry will improve these rates of contaminant destruction.

Elimination of pesticide residues from virgin olive oil by ultraviolet light: preliminary results.

Virgin olive oil is one of the essential products for the economy of Mediterranean countries. The possible residues of pesticides that can reach the oil may be a risk to public health, thus causing the prohibition of its marketing by the health authorities. This paper is a preliminary study on photochemical degradation of pesticide residues using a small-scale prototype (1L capacity). The method presents an effective alternative for the complete photodegradation or reduction of these chemicals using ultraviolet light without harming the quality parameters of the virgin olive oil. The photodegradation yields have varied within the range 7-80% depending on the time and temperature applied.

Radiolytic degradation of atrazine aqueous solution containing humic substances.

Degradation of atrazine herbicide in humic substances (HS) aqueous solutions and distilled water solutions was investigated on a laboratory scale upon gamma-irradiation from a (60)Co source. In addition, the effect of ionizing radiation on the atrazine residues removal efficiency was investigated in relation to degradation of by-products. gamma-Irradiation experiments were carried out for three targeted concentrations (i.e. 0.464, 2.318 and 4.636 microM) with doses over the range 0.1-60 kGy. The initial concentration of herbicide, scavengers and irradiation doses play a significant role in the degradation efficiency as shown by decay constants of atrazine residues. gamma-Radiolysis showed that atrazine exhibited high degradation percentages at low absorbed doses in HS aqueous solutions compared to distilled water solutions. Absorbed doses from 0.6 to 21 kGy and from 6 to 72 kGy at a dose rate of 14.52 kGyh(-1) achieved 90% degradation for atrazine with initial concentrations over the range 0.464-4.636 microM in humic and distilled water solutions, respectively. The radiolytic degradation by-products and their mass balances were qualitatively determined with good confidence using gas chromatography/quadruple mass spectrometry (GC/MS) with electron impact ionization (EI(+)) mode.

Effect of light on the degradation of two neonicotinoids viz acetamiprid and thiacloprid in soil.

Persistence of two neonicotinoids viz thiacloprid and acetamiprid in soil as affected by UV and sunlight exposure was studied. Treated soil was placed in petri-plates, brought to field capacity moisture and then exposed to UV and sunlight. Dissipation for both the pesticides followed monophasic first order kinetics under sunlight, however under UV-light biphasic dissipation was recorded. Residues of acetamiprid and thiacloprid in soil dissipated with half-lives of 11.1 and 12.8 days under UV light and 25.1 and 19.1 days under sunlight, respectively. Residues of both the neonicotinoids dissipated quickly under UV light as compared to sunlight. Exposure of thin film of acetamiprid and thiacloprid to UV and sunlight revealed that acetamiprid is more photo labile than thiacloprid. More than 95% acetamiprid dissipated within 24 h as compared to approximately 70% dissipation observed for thiacloprid.

Influence of metal salts on the photodegradation of imazapyr, an imidazolinone pesticide.

The behaviour of imazapyr (2-(4-isopropyl-4-methyl-5-oxo-2-imidazolin-2-yl)nicotinic acid), a broad spectrum herbicide of the imidazolinone family, has been studied under UV radiation in the presence of metal salts. Complexation interactions between imazapyr and metal ions decreased imazapyr photolysis. A chemometric study compared the photodegradation of imazapyr in aqueous solutions in the presence of Na+, Ca2+ or Cu2+ and their concomitant anionic species (Cl-, NO3-) at various pesticide/metal ion molar ratios. The study showed the major role of metal ions in the degradation of imazapyr and its main photoproducts. The molecules were strongly stabilised on complexation with metal ions, leading to an increase in persistence of the pesticide.

Degradation and by-product formation of diazinon in water during UV and UV/H(2)O(2) treatment.

Kinetics and degradation products resulting from the application of UV and UV/H(2)O(2) to the US EPA Contaminant Candidate List pesticide diazinon were studied. Batch experiments were conducted with both monochromatic (low pressure [LP] UV 253.7 nm) and polychromatic (medium pressure [MP] UV 200-300 nm) UV sources alone or in the presence of up to 50 mg l(-1) H(2)O(2), in a quasi-collimated beam apparatus. Degradation of diazinon by both UV and UV/H(2)O(2) exhibited pseudo first order reaction kinetics, and quantum yield of 8.6 x 10(-2) and 5.8 x 10(-2) mol E(-1) for LP and MP lamps respectively. Photolysis studies under MP UV lamp showed 2-isopropyl-6-methyl-pyrimidin-4-ol (IMP) to be the main degradation product of diazinon at aqueous solution pH values of 4, 7 and 10. Trace levels up to 1.8 x 10(-3) microM of diazinon oxygen analogue diethyl 2-isopropyl-6-methylpyrimidin-4-yl phosphate (diazoxon) were detected only during the UV/H(2)O(2) reaction. Decay of both products was observed, as the UV/H(2)O(2) reaction prolonged, yet no mineralization was achieved over the UV fluence levels examined. Photolysis kinetics, quantum yield and UV/H(2)O(2) degradation of the reaction product IMP was determined using MP UV lamp at pH values of 4, 7 and 10.

Simulation of mefenacet concentrations in paddy fields by an improved PCPF-1 model.

An improved simulation model (PCPF-1) has been evaluated for the prediction of the fate of mefenacet in an experimental paddy field. This model simulates the fate and transport of pesticide in paddy water and the top 1 cm of paddy soil. Observed concentrations of mefenacet in the paddy water and the surface soil exponentially decreased from their maximum concentrations of 0.70 mg litre(-1) and 11.3 mg kg(-1), respectively. Predicted mefenacet concentrations both in the water and surface soil were in excellent agreement with those measured during the first 2 weeks after herbicide application, but concentrations in paddy water were appreciably overestimated thereafter. The model simulated mefenacet losses through runoff, percolation and degradation to be respectively 41.9%, 6.4% and 57.3% of applied, and the mass balance error was about -6%. The model simulation implied that drainage and seepage control, especially shortly after application when herbicide concentrations are high, is essential for preventing pesticide losses from paddy fields. In focusing on pesticide concentrations in this early period the PCPF-1 model can be a beneficial tool for risk assessment of pesticide losses and in the evaluation of agricultural management for reducing pesticide pollution associated with paddy rice production.

Comparison of different mass spectrometric detection techniques in the gas chromatographic analysis of pyrethroid insecticide residues in soil after microwave-assisted extraction.

A comparative study was carried out for the simultaneous determination of 11 pyrethroid insecticides in soil by gas chromatography (GC)--ion trap (IT)--mass spectrometry (MS), by means of two different ionization modes; electron impact and negative chemical ionization and three data acquisition procedures; full scan, selected ion monitoring and MS/MS. Pyrethroids investigated were tetramethrin, bifenthrin, phenothrin, lambda-cyhalothrin, permethrin, cyfluthrin, cypermethrin, flucythrinate, esfenvalerate, fluvalinate and deltamethrin. Soil samples were treated with toluene/water by microwave-assisted extraction for 9 min at 700 W and a cleaning up with florisil was performed. Clean soil samples were spiked with pyrethroids at a spiking level of 10, 25 and 50 ng/g. The method employed provides a concentration factor of 10. The ionization gas employed in the negative chemical ionization mode was methane. The use of MS/MS acquisition, in electron impact ionization, provided the best results, due to its high selectivity and sensitivity, giving very low limits of detection from 0.08 to 0.54 ng/g. In negative chemical ionization full scan and selected ion monitoring methods detection limits from 0.12 to 1.40 ng/g were found. The proposed methods were applied to several levels from 10 to 50 ng/g of spiked soils, being electron impact MS/MS method which minimizes matrix spectrum interferences and provided recovery average values from 84% to 120% with relative standard deviations which varied from 3.2 to 7.2%.

Effect of ultraviolet-absorbing vinyl film on organophosphorus insecticides dichlorvos and fenitrothion residues in spinach.

Dichlorvos and fenitrothion residues found in spinach grown in greenhouse covered either by regular vinyl film or UV-absorbing vinyl film (UV-A) were analyzed by gas chromatography. After one day, dichlorvos residues in spinach covered with regular vinyl film and UV-A degraded by 97% and 80%, respectively, and degraded 100% after three days covered with regular vinyl film and six days covered with UV-A. After three days, fenitrothion residue in spinach covered with regular vinyl film degraded by 72% and then by 97% after six days; residue in spinach covered with UV-A degraded by 50% after three days and by 95% after six days. These results indicate that UV-A used to prevent the occurrence of insects and fungi in greenhouses reduced the degradation rates of dichlorvos and fenitrothion.

Investigation of photochemical behavior of pesticides in a photolysis reactor coupled on-line with a liquid chromatography-electrospray ionization tandem mass spectrometry system. Application to trace and confirmatory analyses in food samples.

The photochemical behavior of pesticides in a photolysis reactor coupled on-line with a liquid chromatography-electrospray ionization mass spectrometer (LC-hv-MS) was investigated. This paper describes the application of LC-hv-MS, in combination with tandem mass spectrometry (MS-MS), to identification of phototransformation products and to the establishment of possible photolytic pathways of pesticides. In addition, the applicability of LC-hv-MS as an alternative to LC-MS-MS, for trace and confirmatory multiresidue analysis in food samples was investigated. To demonstrate the potential of this technique, a series of N-heterocyclic compounds, phenylureas and carbamates, was studied. Several parameters, such as irradiation time and nature of photosensitizers, were investigated, and their impact on the photolytic transformation is presented here. The technique's versatility is also exhibited by using it for identification of triazine isomers, and for detection of pesticide residues in food sample extracts. Illustrative applications for analysis in lettuce and blueberry extracts are described.

Loss of pesticides from patches used in the field as pesticide collectors.

Patches of fabrics exposed to pesticide spray formulations lost substantial quantities of the chemicals within four to six hours. Fabrics were cotton or 1:1 cotton-polyester blends, knitted or woven, unfinished or finished. Pesticides used were parathion, malathion, and dicofol. Parathion loss following exposure to spray formulations was dependent on fabric type, finish and their interaction, while a less extensive loss of dicofol depended on none of these. Deposition and retention of pesticide-bearing particulates appeared to depend on mechanical restrictions related to fabric weave and on the electrokinetic potential of fabric surfaces.

Airborne and surface residues of parathion and its conversion products in a treated plum orchard environment.

Airborne pesticide residues were collected both within and downwind from a parathion-treated plum orchard by high volume sampling through XAD-4 macroreticular resin. Levels of paraoxon in excess of 100 ng/m3 were found in orchard air, along with parathion, during the early days of two 21-day sampling studies. Paraoxon:parathion ratios in the orchard air were relatively constant, averaging ca. 0.5 for days 1 to 21 following treatment. Likely sources of airborne paraoxon include vaporization and dislodgement from soil and leaf surfaces, and chemical conversion of parathion in the air. Support for the latter came from observation of an increased paraoxon:parathion ration in air samples collected downwind from the orchard. Atmospheric conversion of parathion to paraoxon, accelerated by sunlight, was indicated by both field and laboratory studies. Overall dissipation of parathion from the orchard air, soil, and leaf tissue proceeded to a considerable extent through breakdown to paraozon under the dry climatic conditions of these studies. Eventual conversion to the relatively stable breakdown product, p-nitrophenol, was indicated from analysis of air in the orchard vicinity.