Assessment of Drying Protocol on the Bond Strength and Tag Penetration of Two Different Sealers to the Root Dentin: An In Vitro Study.

Accomplishment of an ideal root canal treatment is attributed to various essential factors such as proper instrumentation, chemomechanical preparation, obturation and post endodontic restoration. The main aim of this study is to test the null hypothesis that is the moisture condition of root dentin would not affect the bond strength and sealer penetration. This is an in vitro study conducted in Department of Conservative Dentistry and Endodontics, M A Rangoonwala Dental College, Pune, India over a period of two years (from 2021 to 2023). One hundred and twenty single-rooted Premolars with fully formed apices and similar root morphology were obtained and stored in 0.1% thymol solution. The specimens were randomly assigned to 3 broad experimental groups (n=40) according to the drying protocol such as Group A- Paper points (P), Group B- diode laser (L) and Group C- isopropyl alcohol (A). For each drying protocol, the specimens were further assigned to 2 subgroups (n=20) with respect to the sealers used: AH Plus (AH) and Apexit Plus sealers (APx). The effect of drying protocol using paper points, isopropyl alcohol and diode-lasers on the bond strength and tag penetration of two different sealers to the root dentin was evaluated. Maximum overall push-out Bond strength was seen in group AH+L and least in group APx+ L. Inter-site push-out bond Strength was highest in the coronal third followed by the middle and least in the apical third of all the groups. Maximum over all depth of penetration was seen in group AH+L and minimum in group APx+L. AH plus sealer showed better bond strength, sealer penetration and adaptation to the dentinal walls compared to Apexit plus sealer, irrespective of the drying protocol followed. All the drying protocols used did not show statistically significant results in the apical thirds of root canals of all the groups.

Effects of Lysine on the Interfacial Bonding of Epoxy Resin Cross-Linked Soy-Based Wood Adhesive.

Soy protein isolate (SPI) is an attractive natural material for preparing wood adhesives that has found broad application. However, poor mechanical properties and unfavorable water resistance of wood composites with SPI adhesive bonds limit its more extensive utilization. The combination of lysine (Lys) with a small molecular structure as a curing agent for modified soy-based wood adhesive allows Lys to penetrate wood pores easily and can result in better mechanical strength of soy protein-based composites, leading to the formation of strong chemical bonds between the amino acid and wood interface. Scanning electron microscopy (SEM) results showed that the degree of penetration of the S/G/L-9% adhesive into the wood was significantly increased, the voids, such as ducts of wood at the bonding interface, were filled, and the interfacial bonding ability of the plywood was enhanced. Compared with the pure SPI adhesive, the corresponding wood breakage rate was boosted to 84%. The wet shear strength of the modified SPI adhesive was 0.64 MPa. When Lys and glycerol epoxy resin (GER) were added, the wet shear strength of plywood prepared by the S/G/L-9% adhesive reached 1.22 MPa, which increased by 29.8% compared with only GER (0.94 MPa). Furthermore, the resultant SPI adhesive displayed excellent thermostability. Water resistance of S/G/L-9% adhesive was further enhanced with respect to pure SPI and S/GER adhesives through curing with 9% Lys. In addition, this work provides a new and feasible strategy for the development and application of manufacturing low-cost, and renewable biobased adhesives with excellent mechanical properties, a promising alternative to traditional formaldehyde-free adhesives in the wood industry.

Intratubular penetration of endodontic sealers depends on the fluorophore used for CLSM assessment.

Root canal filling aims at eliminating empty spaces into the root canal system using biologically compatible materials. Three-dimensional root canal obturation must prevent or minimize the reinfection caused by microorganisms' leakage. This study aimed at evaluating whether fluorophore (Rhodamine or Fluo-3) influences the CLSM images of intratubular penetration of four endodontic sealers. Eighty bovine teeth were prepared using K files up to a size #70 and irrigated with 2.5% sodium hypochlorite. All roots were divided into eight groups (n = 10) according to the sealer and fluorophore used: AH Plus/Rhodamine, AH Plus/Fluo-3, Sealer Plus/Rhodamine, Sealer Plus/Fluo-3, Sealer Plus BC/Rhodamine, Sealer Plus BC/Fluo-3, Endosequence/Rhodamine, and Endosequence/Fluo-3. All roots were filled using cold lateral compaction technique. After 7 days, the roots were transversely sectioned, and three slices, one of each canal third, were obtained. Intratubular penetration was evaluated using CLSM. Sealer Plus BC/Rhodamine and Endosequence BC/Rhodamine presented higher intratubular penetration than AH Plus/Fluo-3 and Sealer Plus/Fluo-3 (p ˂ .05). The intragroup analysis showed similar intratubular penetration, regardless of the root third, except for the apical third in AH Plus/Fluo-3 and Sealer Plus BC/Fluo-3 groups. The type of fluorophore influences the calcium silicate sealers' tubular penetration but not of epoxy resin-based ones using CLSM. Bioceramic sealers should not be used associated with Rhodamine for CLSM evaluation. RESEARCH HIGHLIGHTS: The type of fluorophore influences the calcium silicate sealers' tubular penetration but not of epoxy resin-based ones when CLSM is used for assessment. Bioceramic sealers should not be used associated with Rhodamine.

Occupational exposure to carbon fibers impregnated with epoxy resins and evaluation of their respirability.

Objectives: The study aims to investigate occupational exposure to carbon fibers impregnated with epoxy resins (carbon fiber reinforced [CFR]) in workers at an airplane fuselage section construction plant, by environmental and biological monitoring.Materials and methods: Determination of airborne CFR was done by environmental sampling with active samplers, 11 of which were stationary and 19 personal samplings. The subsequent analyses were performed in the scanning electron microscope fitted with an X-ray microanalysis system (SEM-EDXA). Biological monitoring was carried out by determining CFR in exhaled breath condensate (EBC) collected from 19 male workers who wore personal environmental samplers (exposed workers) and from 10 male workers at the same factory who had no occupational exposure to CFR (internal controls). CFR analysis was done by SEM, applying the method used for determining asbestos fibers in aqueous samples.Results: The airborne CFR concentrations were found to be significantly higher (p = 0.03) at personal samplings (median value 7.01 ff/L, range 1.24-11.16 ff/L) than stationary samplings (median value 1.93 ff/L, range 0.55-10.09 ff/L). The aerodynamic diameters calculated starting from the length and geometric diameter of the sampled CFRs were always higher than 20 µm. CFR was not found in any of the EBC samples collected from the exposed workers and controls.Conclusions: Despite the evidence of occupational exposure to low concentrations of CFR, the absence of such fibers in the EBC in the exposed workers confirms their non-respirability, as expected based on their aerodynamic diameter.

Influence of Storage Time and Temperature on the Toxicity, Endocrine Potential, and Migration of Epoxy Resin Precursors in Extracts of Food Packaging Materials.

The aim of the present study was to establish a standard methodology for the extraction of epoxy resin precursors from several types of food packages (cans, multi-layered composite material, and cups) with selected simulation media (distilled water, 5% ethanol, 3% dimethyl sulfoxide, 5% acetic acid, artificial saliva) at different extraction times and temperatures (factors). Biological analyses were conducted to determine the acute toxicity levels of the extracts (with Vibrio fischeri bacteria) and their endocrine potential (with Saccharomyces cerevisiae yeasts). In parallel, liquid chromatography-tandem mass spectrometry was performed to determine levels of bisphenol A diglycidyl ether (BADGE), bisphenol F diglycidyl ether (mixture of isomers, BFDGE), ring novolac glycidyl ether (3-ring NOGE), and their derivatives. The variation induced by the different experimental factors was statistically evaluated with analysis of variance simultaneous component analysis (ASCA). Our findings demonstrate the value of using a holistic approach to best partition the effects contributing to the end points of these assessments, and offer further guidance for adopting such a methodology, thus being a broadly useful reference for understanding the phenomena related to the impacts of food packaging materials on quality for long- and short-term storage, while offering a general method for analysis.

Assessment of the Impact of Accelerated Migration Testing for Coated Food Cans Using Food Simulants.

In this study, an accelerated migration test on food can coatings into food simulants was investigated. Food simulants covering a wide range of polarity were used to conduct migration tests at 60 °C with storage times ranging from 4 h to 30 days. Epoxy-resins, acrylic-phenolic, polyester, and vinyl coatings were exposed to water, 3% acetic acid, 50% ethanol, and Miglyol 812®. Using liquid chromatography coupled to a variety of detectors (UHPLC-Q-Orbitrap-MS, UFLC-MS/MS, and HPLC-DAD), migration of several monomers and previously identified oligomers, as well as some unidentified migrants, were determined during the experiment. The data from this study was compared to our findings from previous long-term migration studies with storage times ranging from 24 h to 540 days at 40 °C using the same can coating applications. The results illustrate that performing migration experiments for short time periods at 60 °C may mimic migration results that would be obtained at 40 °C after long-term migration tests (up to 1.5 years) from food can coatings into food simulants.

Exploration of cardanol-based phenolated and epoxidized resins by size exclusion chromatography and MALDI mass spectrometry.

Cardanol and cardanol derivatives are among the most important biobased materials currently investigated in green chemistry, as renewable and promising building blocks in lieu of traditional raw materials from non renewable resources, in particular owing to the olefinic linkages on the C15 alkyl side-chain. Despite the increasing interest they arouse, analytical chemistry dedicated to cardanol and associated resins has been rarely reported in the literature, found even poorer when dealing with chromatography and mass spectrometry. In this work, a thorough molecular characterization was conducted using matrix assisted laser desorption ionization (MALDI) mass spectrometry, size exclusion chromatography (SEC), and SEC-MALDI coupling to gain insights into the composition of phenolated, epoxidized, and epoxidized phenolated cardanol. A nomenclature was proposed to properly describe the numerous species found in these materials, while simulations of the unsaturation patterns and their comparison with the detected patterns in MALDI-MS gave useful details about the phenolation treatment expected to occur on the polyunsaturated C15 side chain. Finally, the SEC-MALDI off-line coupling allowed SEC peaks to be deconvoluted by mass spectrometry and MALDI artefacts related to matrix adduction to be pointed out.

Fuzzy similarity measures for detection and classification of defects in CFRP.

The systematic use of nondestructive testing assumes a remarkable importance where on-line manufacturing quality control is associated with the maintenance of complex equipment. For this reason, nondestructive testing and evaluation (NDT/NDE), together with accuracy and precision of measurements of the specimen, results as a strategic activity in many fields of industrial and civil interest. It is well known that nondestructive research methodologies are able to provide information on the state of a manufacturing process without compromising its integrity and functionality. Moreover, exploitation of algorithms with a low computational complexity for detecting the integrity of a specimen plays a crucial role in real-time work. In such a context, the production of carbon fiber resin epoxy (CFRP) is a complex process that is not free from defects and faults that could compromise the integrity of the manufactured specimen. Ultrasonic tests provide an effective contribution in identifying the presence of a defect. In this work, a fuzzy similarity approach is proposed with the goal of localizing and classifying defects in CFRP in terms of a sort of distance among signals (measure of ultrasonic echoes). A field-programmable gate array (FPGA)-based board will be also presented which implements the described algorithms on a hardware device. The good performance of the detection and classification achieved assures the comparability of the results with the results obtained using heuristic techniques with a higher computational load.

Persistence of epoxy-based sealer residues in dentin treated with different chemical removal protocols.

The presence of residual endodontic sealer in the pulp chamber may cause discoloration of the dental crown and interfere with the adhesion of restorative materials. The aim of this study was to compare the efficacy of different solvents in removing residues of an epoxy resin-based sealer (AH Plus) from the dentin walls of the pulp chamber, by scanning electron microscopy (SEM). Forty-four bovine incisor dental crown fragments were treated with 17% EDTA and 2.5% NaOCl. Specimens received a coating of AH Plus and were left undisturbed for 5 min. Then, specimens were divided in four groups (n = 10) and cleaned with one of the following solutions: isopropyl alcohol, 95% ethanol, acetone solution, or amyl acetate solution. Negative controls (n = 2) did not receive AH Plus, while in positive controls (n = 2) the sealer was not removed. AH Plus removal was evaluated by SEM, and a score system was applied. Data were analyzed by Kruskal-Wallis and Dunn tests. None of the solutions tested was able to completely remove AH Plus from the dentin of the pulp chamber. Amyl acetate performed better than 95% ethanol and isopropyl alcohol (p < 0.05), but not better than acetone (p > 0.05) in removing the sealer from dentin. No significant differences were observed between acetone, 95% ethanol, and isopropyl alcohol (p > 0.05). It was concluded that amyl acetate and acetone may be good options for cleaning the pulp chamber after obturation with AH Plus.

The crash of Colgan Air flight 3407: Advanced techniques in victim identification.

BACKGROUND: Identifying disaster victims by means of dental records is a well-established technique. In cases in which high temperatures are involved, destruction of the structural relationship of the dentition necessitates that adjunctive aids be used in the identification process. Analysis of tooth fragments by means of scanning electron microscopy with energy dispersive x-ray spectroscopy can reveal evidence of restorative procedures, as well as trace amounts of dental materials remaining on tooth surfaces. In addition, dental materials can be analyzed and identified according to brand, even if the materials have been cremated. CASE DESCRIPTION: The authors describe the identification of three victims from the crash of Colgan Air flight 3407, a commuter airplane flying between Newark, N.J., and Buffalo, N.Y. The crash involved a fire, and a portion of the airplane burned for nearly 11 hours. Dental fragments that had restorative material adhering to them were recovered and analyzed. These fragments contained corroborative information that helped confirm the identity of the victims. CLINICAL IMPLICATIONS: Detailed record keeping is part of clinical practice. The level of detail present in dental records can affect the ability of forensic odontologists to determine the identity of a victim's remains. Documenting the brand names of dental materials used in restorative procedures can make the difference between identifying and not identifying a victim's remains.

Quantitative characterization of solid epoxy resins using comprehensive two dimensional liquid chromatography coupled with electrospray ionization-time of flight mass spectrometry.

A comprehensive multidimensional liquid chromatography system coupled to Electrospray Ionization-Mass Spectrometry (LCxLC-ESI-MS) was developed for detailed characterization and quantitation of solid epoxy resin components. The two orthogonal modes of separation selected were size exclusion chromatography (SEC) in the first dimension and liquid chromatography at critical conditions (LCCC) in the second dimension. Different components present in the solid epoxy resins were separated and quantitated for the first time based on the functional groups and molecular weight heterogeneity. Coupling LCxLC separations with mass spectrometry enabled the identification of components resolved in the two-dimensional space. Several different functional group families of compounds were separated and identified, including epoxy-epoxy and epoxy-alpha-glycol functional oligomers, and their individual molecular weight ranges were determined. Repeatability obtained ranged from 0.5% for the main product to 21% for oligomers at the 0.4% concentration level.

Análise da capacidade de reprodução de detalhes expressa por diferentes materiais de modelagem / Analysis of the capacity to reproduce details expressed by different modeling materials

Este estudo objetivou avaliar a capacidade de reprodução de detalhes presentes no molde por materiais de modelagem à base de gipsita Gesso pedra tipo IV, Durone, (Dentsply); Gesso pedra tipo IV, Fuji Rock EP,(GC); Gesso pedra tipo IV, Resinado Rock Plus, (Polidental); Gesso pedra tipo V, Durone, (Dentsply) epolímeros: resinas epóxicas Epoxiglass 1504, (Epoxiglass), resina epóxica Epoxiglass 1504 modificada com diatomita pura e silanizada. A resina e seu endurecedor foram carregados com diatomita numa relação de30%. A diatomita foi tratada com Silano Silquest A 187, (Crompton S/A). A resina modificada foi manipuladaem uma relação de 35%. Empregando-se silicona de adição Presidente (Kit de silicona leve e pesada, Coltène) realizaram-se três moldagens de uma matriz metálica com quatro hastes contendo sulcos dimensionados. Os corpos de prova foram analisados em microscópio óptico com aumento de 40 vezes (Measurescope Nikon, procedência Nippon Kogaru K. K.). Os resultados expressos por gessos e resinas foram analisados com o teste Variância e Tukey (p<0,05). Verificou-se que não há diferenças estatisticamente significantes entre os gessos e resinas analisadas. Concluiu-se que o carregamento da resina epóxica com diatomita ou com diatomita silanizada não reduz a sua capacidade em reproduzir detalhes presentes no molde. Com a metodologia empregada, não houve diferença entre gessos tipo IV e V e resina epóxica pura ou modificada com diatomita na capacidadede reprodução de detalhes presentes no molde.

Kinetic analysis of reactions of Si-based epoxy resins by near-infrared spectroscopy, 13C NMR and soft-hard modelling.

Soft- and hard-modelling strategy was applied to near-infrared spectroscopy data obtained from monitoring the reaction between glycidyloxydimethylphenyl silane, a silicon-based epoxy monomer, and aniline. On the basis of the pure soft-modelling approach and previous chemical knowledge, a kinetic model for the reaction was proposed. Then, multivariate curve resolution-alternating least squares optimization was carried out under a hard constraint, that compels the concentration profiles to fulfil the proposed kinetic model at each iteration of the optimization process. In this way, the concentration profiles of each species and the corresponding kinetic rate constants of the reaction, unpublished until now, were obtained. The results obtained were contrasted with 13C NMR. The joint interval test of slope and intercept for detecting bias was not significant (alpha=5%).

Multivariate curve resolution-alternating least squares and kinetic modeling applied to near-infrared data from curing reactions of epoxy resins: mechanistic approach and estimation of kinetic rate constants.

This study describes the combination of multivariate curve resolution-alternating least squares with a kinetic modeling strategy for obtaining the kinetic rate constants of a curing reaction of epoxy resins. The reaction between phenyl glycidyl ether and aniline is monitored by near-infrared spectroscopy under isothermal conditions for several initial molar ratios of the reagents. The data for all experiments, arranged in a column-wise augmented data matrix, are analyzed using multivariate curve resolution-alternating least squares. The concentration profiles recovered are fitted to a chemical model proposed for the reaction. The selection of the kinetic model is assisted by the information contained in the recovered concentration profiles. The nonlinear fitting provides the kinetic rate constants. The optimized rate constants are in agreement with values reported in the literature.

Electrochemical biosensing based on universal affinity biocomposite platforms.

Rigid conducting biocomposites are versatile and effective transducing materials for the construction of a wide range of amperometric biosensors such as immunosensors, genosensors and enzymosensors, particularly if the transducer is bulk-modified with universal affinity biomolecules. The strept(avidin)-graphite-epoxy biocomposite could be considered as an universal immobilization platform whereon biotinylated DNAs, oligonucleotides, enzymes or antibodies can be captured by means of the highly affinity (strept)avidin-biotin reaction. Universal affinity biocomposite-based biosensors offer many potential advantages compared to more traditional electrochemical biosensors commonly based on a biologically surface-modified transducer. The integration of many materials into one matrix is their main advantage. As biological bulk-modified materials, the conducting biocomposites act not only as transducers, but also as reservoir for the biomaterial. After its use, the electrode surface can be renewed by a simple polishing procedure, establishing a clear advantage of these approaches relative to classical biosensors and other common biological assays. Moreover, the same material is useful for the analysis of many molecules whose determinations are based on genetic, enzymatic or immunological reactions. The different strategies for electrochemical genosensing, immunosensing and enzymosensing, all of them being dependent on the presence of a redox enzyme marker for the generation of the electrochemical signal, based on this universal affinity biocomposite platform are all presented and discussed.

Neutron shielding material based on colemanite and epoxy resin.

In recent years, there has been a need for compact shielding design such as self-shielding of a PET cyclotron or upgradation of radiation machinery in existing facilities. In these cases, high performance shielding materials are needed. Concrete or polyethylene have been used for a neutron shield. However, for compact shielding, they fall short in terms of performance or durability. Therefore, a new type of neutron shielding material based on epoxy resin and colemanite has been developed. Slab attenuation experiments up to 40 cm for the new shielding material were carried out using a 252Cf neutron source. Measurement was carried out using a REM-counter, and compared with calculation. The results show that the shielding performance is better than concrete and polyethylene mixed with 10 wt% boron oxide. From the result, we confirmed that the performance of the new material is suitable for practical use.

Modeling of complex viscosity changes in the curing of epoxy resins from near-infrared spectroscopy and multivariate regression analysis.

The present study investigates the relationship between the changes in complex viscosity and near-infrared spectra. Principal component regression analysis is applied to a near-infrared data set obtained from the in situ monitoring of the curing of diglycidyl ether of bisphenol A with the diamine 4,4'-diaminodiphenylmethane. The values of complex viscosity obtained by dynamic mechanical analysis during the cure process were used as a reference. The near-infrared spectra recorded throughout the reaction, unlike the univariate data analysis at some wavelengths of the spectra, contain a sufficient amount of information to estimate the complex viscosity. The relationship found was high and the results demonstrate the quality of the fitted model. Also, a simple user-friendly procedure for applying the model, focused on the user, is shown.

Time-resolved spectrophotometer for turbid media based on supercontinuum generation in a photonic crystal fiber.

We describe an instrument for the time-resolved spectroscopy of turbid media that is based on supercontinuum generation in a photonic crystal fiber. The light injected into the sample consists of subpicosecond pulses that cover 550-1000 nm at 85 MHz at an average power of as much as 40 mW. A spectrometer coupled to a multianode photomultiplier tube is used to detect the light simultaneously in 16 wavelength channels, with a resolution of 5-20 nm/channel, depending on the grating. Time-correlated single-photon counting is used to produce time-dispersion curves, which one fits to the diffusion equation to determine absorption and reduced scattering coefficients. We tested the instrument by measuring the time-resolved diffuse reflectance of epoxy phantoms and by performing in vivo measurements on volunteers. The results were similar to those obtained with previous discrete wavelength systems, whereas the full spectrum (610-810 nm) acquisition time was as short as 1 s owing to the parallel acquisition.