Statistical evaluation of measured biomechanical properties of human brain aneurysm samples.

Background and purpose:

Human brain aneurysms may often prove fatal if not re­cognized in time and treated accordingly. The understanding of development and rupture of aneurysms can significantly be improved by the application of numerical modelling, which in turn, requires the knowledge of mechanical properties of vessel wall. This study aims to identify assumed differences with respect to age, sex, spatial orientation, and rupture by utilizing detailed statistical analysis of uniaxial tensile measurements of human brain aneurysm samples, performed by the authors in a previous project.

At surgery of 42 patients, aneu­rysm fundi were cut distally to the clip. In each case, depending on size, varying number of stripes (altogether 88) were prepared and uniaxial stress-strain measurements were performed. Quantities related to the capacity, energy absorption or stiffness were determined and statistically analysed.

The number of specimens in the aneurysm sample was sufficient to establish statistical differences with respect to sex and rupture (p<0.05). No significant differences were detected in orientation, though higher values of stresses and deformations were ob­tained in the circumferential direction com­pared to the meridional direction. 

Significant differences bet­ween sexes with respect to ultimate deformations were demonstrated according to expectation, and the hypothesis on equality of energy capacity could be supported. Similarity of curves with respect to specimen orientation was also observed and ruptured aneurysm sacs tended to be smaller in size. It seems that differences and trends described in this paper are realistic and need to be applied in numerical modelling.

Preparation of films based on reticulated fish gelatin containing garlic essential oil.

Agro-industrial co-products, such as fish gelatin, stand out for their capacity in forming biopolymeric films, being biocompatible and non-toxic; however, its hydrophilicity poses a challenge. Essential oils, rich in bioactives, attract research interest aiming to enhance the protective barrier of films and enable their application in packaging. This study produced films based on cross-linked Nile tilapia skin gelatin, incorporating garlic essential oil. Gelatin obtained through partial collagen hydrolysis from the fish skin and cross-linked with gallic acid had hydroxyproline content of 10.02 g 100 g-1 and gel strength of 287 g, which were consistent with other studies. Oil extraction used supercritical CO2 as a solvent and ethanol as a cosolvent, following a factorial experimental design, evaluating the extraction temperature (40 °C and 70 °C) and cosolvent ratio (1:1 and 1:3), with three central points. Extraction was successful, with higher yields on a dry basis at 70 °C (88.35 %), using a 1:1 cosolvent ratio. Films incorporated with oil exhibited lower water vapor permeability (WVP) than those with only cross-linked gelatin (1.59 (g m-1 s-1 Pa-1) 1011). The film with the most suitable tensile strength (19.07 MPa), elongation (120.91 %), and WVP (1.09 (g m-1 s-1 Pa-1) 1011) properties contained garlic oil extracted at the central point (55 °C and 1:2). Thermal analysis indicated increased melting temperatures in films with added oil, suggesting low thermal degradation. These results suggest that garlic oil addition can improve the properties of fish gelatin-based films, making them promising for biodegradable packaging.

Preparation of Steamed Purple Sweet Potato-Based Films Containing Mandarin Essential Oil for Smart Packaging.

Anthocyanin-rich steamed purple sweet potato (SPSP) is a suitable raw material to produce smart packaging films. However, the application of SPSP-based films is restricted by the low antimicrobial activity of anthocyanins. In this study, SPSP-based smart packaging films were produced by adding mandarin essential oil (MEO) as an antimicrobial agent. The impact of MEO content (3%, 6%, and 9%) on the structures, properties, and application of SPSP-based films was measured. The results showed that MEO created several pores within films and reduced the hydrogen bonding system and crystallinity of films. The dark purple color of the SPSP films was almost unchanged by MEO. MEO significantly decreased the light transmittance, water vapor permeability, and tensile strength of the films, but remarkably increased the oxygen permeability, thermal stability, and antioxidant and antimicrobial properties of the films. The SPSP-MEO films showed intuitive color changes at different acid-base conditions. The purple-colored SPSP-MEO films turned blue when chilled shrimp and pork were not fresh. The MEO content greatly influenced the structures, physical properties, and antioxidant and antimicrobial activities of the films. However, the MEO content had no impact on the color change ability of the films. The results suggested that SPSP-MEO films have potential in the smart packaging of protein-rich foods.

Highly Stretchable Double Network Ionogels for Monitoring Physiological Signals and Detecting Sign Language.

At the heart of the non-implantable electronic revolution lies ionogels, which are remarkably conductive, thermally stable, and even antimicrobial materials. Yet, their potential has been hindered by poor mechanical properties. Herein, a double network (DN) ionogel crafted from 1-Ethyl-3-methylimidazolium chloride ([Emim]Cl), acrylamide (AM), and polyvinyl alcohol (PVA) was constructed. Tensile strength, fracture elongation, and conductivity can be adjusted across a wide range, enabling researchers to fabricate the material to meet specific needs. With adjustable mechanical properties, such as tensile strength (0.06-5.30 MPa) and fracture elongation (363-1373%), this ionogel possesses both robustness and flexibility. This ionogel exhibits a bi-modal response to temperature and strain, making it an ideal candidate for strain sensor applications. It also functions as a flexible strain sensor that can detect physiological signals in real time, opening doors to personalized health monitoring and disease management. Moreover, these gels' ability to decode the intricate movements of sign language paves the way for improved communication accessibility for the deaf and hard-of-hearing community. This DN ionogel lays the foundation for a future in which e-skins and wearable sensors will seamlessly integrate into our lives, revolutionizing healthcare, human-machine interaction, and beyond.

The Influence of Various Crosslinking Conditions of EDC/NHS on the Properties of Fish Collagen Film.

The process of crosslinking improves the physicochemical properties of biopolymer-based composites, making them valuable for biomedical applications. EDC/NHS-crosslinked collagen materials have a significant potential for tissue engineering applications, due to their enhanced properties and biocompatibility. Chemical crosslinking of samples can be carried out in several ways, which is crucial and has a direct effect on the final properties of the obtained material. In this study, the effect of crosslinking conditions on the properties of collagen films using EDC and NHS was investigated. Studies included FTIR spectroscopy, AFM, swelling and degradation tests, mechanical testing and contact angle measurements. Evaluation of prepared collagen films indicated that both crosslinking agents and crosslinking conditions influenced film properties. Notable alternations were observed in the infrared spectrum of the sample, to which EDC was added directly to the fish collagen solution. The same sample indicated the lowest Young modulus, tensile strength and breaking force parameters and the highest elongation at break. All samples reached the maximum swelling degree two hours after immersion in PBS solution; however, the immersion-crosslinked samples exhibited a significantly lower degree of swelling and were highly durable. The highest roughness was observed for the collagen film crosslinked with EDC, whereas the lowest was observed for the specimen crosslinked with EDC with NHS addition. The crosslinking agents increased the surface roughness of the collagen film, except for the sample modified with the addition of EDC and NHS mixture. All films were characterized by hydrophilic character. The films' modification resulted in a decrease in their hydrophilicity and wettability. Our research allows for a comparison of proposed EDC/NHS crosslinking conditions and their influence on the physicochemical properties of fish collagen thin films. EDC and NHS are promising crosslinking agents for the modification of fish collagen used in biomedical applications.

Whey Protein Isolate as a Substrate to Design Calendula officinalis Flower Extract Controlled-Release Materials.

The use of natural active substances and the development of new formulations are promising directions in the cosmetic and pharmacy industries. The primary purpose of this research was the production of microparticles based on whey protein isolate (WPI) and calcium alginate (ALG) containing Calendula officinalis flower extract and their incorporation into films composed of gelatin, WPI, and glycerol. Both swollen and dry microparticles were studied by optical microscopy and their sizes were measured. Water absorption by the microparticles, their loading capacity, and the release profile of flower extract were also characterized. The films were analyzed by mechanical tests (Young's modulus, tensile strength, elongation at break), swelling capacity, contact angle, and moisture content measurements. The presented data showed that the active ingredient was successfully enclosed in spherical microparticles and completely released after 75 min of incubation at 37 °C. The incorporation of the microparticles into polymer films caused a decrease in stiffness and tensile strength, simultaneously increasing the ductility of the samples. Moreover, the films containing microparticles displayed higher swelling ability and moisture content compared to those without them. Hence, the materials prepared in this study with Calendula officinalis flower extract encapsulated into polymeric microspheres can be a starting point for the development of new products intended for skin application; advantages include protection of the extract against external factors and a controlled release profile.

Selection of lubricant type and concentration for orodispersible tablets.

Lubricants are essential for most tablet formulations as they assist powder flow, prevent adhesion to tableting tools and facilitate tablet ejection. Magnesium stearate (MgSt) is an effective lubricant but may compromise tablet strength and disintegratability. In the design of orodispersible tablets, tablet strength and disintegratability are critical attributes of the dosage form. Hence, this study aimed to conduct an in-depth comparative study of MgSt with alternative lubricants, namely sodium lauryl sulphate (SLS), stearic acid (SA) and hydrogenated castor oil (HCO), for their effects on the tableting process as well as tablet properties. Powder blends were prepared with lactose, sodium starch glycolate or crospovidone as the disintegrant, and a lubricant at different concentrations. Angle of repose was determined for the mixtures. Comparative evaluation was carried out based on the ejection force, tensile strength, liquid penetration and disintegratability of the tablets produced. As the lubricant concentration increased, powder flow and tablet ejection improved. The lubrication efficiency generally decreased as follows: MgSt > HCO > SA > SLS. Despite its superior lubrication efficacy, MgSt is the only lubricant of four evaluated that reduced tablet tensile strength. Tablet disintegration time was strongly determined by tensile strength and liquid penetration, which were in turn affected by the lubricant type and concentration. All the above factors should be taken into consideration when deciding the type and concentration of lubricant for an orodispersible tablet formulation.

Mechanical properties of hydrated electrospun polycaprolactone (PCL) nanofibers.

Polycaprolactone (PCL) nanofibers are a promising material for biomedical applications due to their biocompatibility, slow degradation rate, and thermal stability. We electrospun PCL fibers onto a striated substrate with 12 µm wide ridges and grooves and determined their mechanical properties in an aqueous solution with a combined atomic force/inverted optical microscopy technique. Fiber diameters, D, ranged from 27 to 280 nm. The hydrated PCL fibers had an extensibility (breaking strain), εmax, of 137%. The Young's modulus, E, and tensile strength, σT, showed a strong dependence on fiber diameter, D; decreasing steeply with increasing diameter, following empirical equations E(D)=(4.3∙103∙e-D51nm+1.1∙102) MPa and σT(D)=(2.6∙103∙e-D55nm+0.6∙102) MPa. Incremental stress-strain measurements were employed to investigate the viscoelastic behavior of these fibers. The fibers exhibited stress relaxation with a fast and slow relaxation time of 3.7 ± 1.2 s and 23 ± 8 s and these experiments also allowed the determination of the elastic and viscous moduli. Cyclic stress-strain curves were used to determine that the elastic limit of the fibers, εelastic, is between 19% and 36%. These curves were also used to determine that these fibers showed small energy losses (<20%) at small strains (ε < 10%), and over 50% energy loss at large strains (ε > 50%), asymptotically approaching 61%, as Eloss=61%·(1-e-0.04*ε). Our work is the first mechanical characterization of hydrated electrospun PCL nanofibers; all previous experiments were performed on dry PCL fibers, to which we will compare our data.

Numerical investigation of fluid flow behavior in steel cord with lattice Boltzmann methodology: The impacts of microstructure and loading force.

Steel cord materials were found to have internal porous microstructures and complex fluid flow properties. However, current studies have rarely reported the transport behavior of steel cord materials from a microscopic viewpoint. The computed tomography (CT) scanning technology and lattice Boltzmann method (LBM) were used in this study to reconstruct and compare the real three-dimensional (3D) pore structures and fluid flow in the original and tensile (by loading 800 N force) steel cord samples. The pore-scale LBM results showed that fluid velocities increased as displacement differential pressure increased in both the original and tensile steel cord samples, but with two different critical values of 3.3273 Pa and 2.6122 Pa, respectively. The original steel cord sample had higher maximal and average seepage velocities at the 1/2 sections of 3D construction images than the tensile steel cord sample. These phenomena should be attributed to the fact that when the original steel cord sample was stretched, its porosity decreased, pore radius increased, flow channel connectivity improved, and thus flow velocity increased. Moreover, when the internal porosity of tensile steel cord sample was increased by 1 time, lead the maximum velocity to increase by 1.52 times, and the average velocity was increased by 1.66 times. Furthermore, when the density range was determined to be 0-38, the pore phase showed the best consistency with the segmentation area. Depending on the Zou-He Boundary and Regularized Boundary, the relative error of simulated average velocities was only 0.2602 percent.

Effect of Poly(propylene carbonate) on Properties of Polylactic Acid-Based Composite Films.

To enrich the properties of polylactic acid (PLA)-based composite films and improve the base degradability, in this study, a certain amount of poly(propylene carbonate) (PPC) was added to PLA-based composite films, and PLA/PPC-based composite films were prepared by melt blending and hot-press molding. The effects of the introduction of PPC on the composite films were analyzed through in-depth studies on mechanical properties, water vapor and oxygen transmission rates, thermal analysis, compost degradability, and bacterial inhibition properties of the composite films. When the introduction ratio coefficient of PPC was 30%, the tensile strength of the composite film increased by 19.68%, the water vapor transmission coefficient decreased by 14.43%, and the oxygen transmission coefficient decreased by 18.31% compared to that of the composite film without PPC, the cold crystallization temperature of the composite film increased gradually from 96.9 °C to 104.8 °C, and PPC improved the crystallization ability of composite film. The degradation rate of the composite film with PPC increased significantly compared to the previous one, and the degradation rate increased with the increase in the PPC content. The degradation rate was 49.85% and 46.22% faster on average than that of the composite film without PPC when the degradation was carried out over 40 and 80 days; the composite film had certain inhibition, and the maximum diameter of the inhibition circle was 2.42 cm. This study provides a strategy for the development of PLA-based biodegradable laminates, which can promote the application of PLA-based laminates in food packaging.

Effect of the ex situ physical and in situ chemical modification of bacterial nanocellulose on mechanical properties in the context of its potential applications in heart valve design.

Bacterial nanocellulose (BNC) is a promising material for heart valve prostheses. However, its low strength properties limit its applicability in cardiovascular surgery. To overcome these limitations, the mechanical properties of BNC can be improved through modifications. The aim of the research was to investigate the extent to which the mechanical properties of BNC can be altered by modifying its structure during its production and after synthesis. The study presents the results of various analyses, including tensile tests, nanoindentation tests, X-ray diffraction (XRD) tests, scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR) and Raman spectroscopy, conducted on BNC chemically modified in situ with hyaluronic acid (BNC/HA) and physically modified ex situ through a dehydration/rehydration process (BNC 25DR, BNC105DR, BNC FDR and BNC/HA 25DR, BNC/HA 105DR, BNC/HA FDR). The results demonstrate that both chemical and physical modifications can effectively shape the mechanical properties of BNC. These modifications induce changes in the crystalline structure, pore size and distribution, and residual stresses of BNC. Results show the effect of the crystalline structure of BNC on its mechanical properties. There is correlation between hardness and Young's modulus and Iα/Iß index for BNC/HA and between creep rate of BNC/HA, and Young's modulus for BNC vs Iα/Iß index.

Physicochemical and thermal characterization of the edible shellac films incorporated with oleic acid to enhance flexibility, water barrier and retard aging.

In this work, shellac plasticized with oleic acid was solvent cast to prepare the flexible and water-resistant film for packaging applications. The films were prepared with varying amounts of oleic acid and studied in detail for appearance, surface morphology, thermal, chemical, barrier, mechanical, and robustness. The surface morphology confirmed the smooth surface of films up to SH-OA20 (100:20 w/w; shellac: oleic acid). Fourier-transform infrared spectroscopy confirmed that oleic acid reduced the hydrogen bonding of the shellac matrix to provide a plasticization effect. Also, the thermal analysis showed a reduction in the melting enthalpy. Moreover, the plasticized films had a better barrier to water vapor due to increased smoothness and reduction in brittleness. Adding oleic acid also increased the elongation at break up to 40 % without any changes in tensile strength. The flexibility of the films increased with the oleic acid content, making them resistant to burst, crumbling, bending, rolling, and stretching. Oleic acid also showed the retardation of aging and thermal aging of shellac. In the future, the long-term stability and migration of the films can be investigated.

Self-assembled lignin-based flame retardant hybrids carrying Cu2+ for poly(lactic acid) composites with improved fire safety and mechanical properties.

To enhance the flame retardancy and mechanical performance of PLA, a polyelectrolyte complex predicated on lignin was obtained by electrostatic mutual adsorption of ammonium polyphosphate (APP), polyethyleneimine (PEI), and copper ions as raw materials. The FT-IR spectra and EDX analysis confirmed the successful synthesis of a lignin-based flame retardant hybrid (APL-Cu2+) containing copper, phosphorus, and nitrogen elements. The combustion test results showed that the peak heat release rate and total heat release of the PLA composite containing 12 wt% APL-Cu2+ were decreased by 15.1 % and 18.2 %, respectively, as compared to those of pure PLA. The char residue morphology observation revealed that the addition of APL-Cu2+ could promote the formation of a highly dense and stable graphitized char layer, while TG-MS detected the emission of refractory gases such as ammonia gas, carbon dioxide, and water during combustion. The strong hydrogen bonding between APL-Cu2+ and the PLA matrix kept the composite maintaining good strength and toughness. The tensile strength and impact strength of PLA/6APL-Cu2+ increased by 4.73 % and 65.71 %, respectively, due to its high crystallinity and good interfacial compatibility. This work provides a feasible method to develop biobased flame retardant hybrids for PLA composites with better fire safety and improved mechanical properties.

Continuous preparation and antibacterial mechanisms of biodegradable polylactic acid/nano-zinc oxide/additives antibacterial non-wovens.

Biodegradable polylactic acid (PLA)/nano­zinc oxide (ZnO)/additives non-woven slices were prepared by melt blending method. The effects of antibacterial agent nano-ZnO, antioxidant pentaerythrityl tetrakis-(3,5-di-tert-butyl-4-hydroxyphenyl)-propionate (1010), and chain extender multi-functional epoxy (ADR), on the melt flow rate, mechanical properties, thermal stabilities and micromorphology of the slices were investigated. The melt flow rate decreased from 26.94 g/10 min to 17.76 g/10 min, and the tensile strength increased from 10.518 MPa to 30.427 MPa with the increase of nano-ZnO and additives content. The slices were further spunbonded. The wettability and antibacterial properties of PLA/nano-ZnO/additives antibacterial non-wovens were studied, and the antibacterial action mechanism was clarified. The results showed that the biodegradable PLA/nano-ZnO/additives antibacterial non-wovens were prepared continuously successfully. The prepared non-woven fabrics exhibited good hydrophobicity and antibacterial properties. The mechanism study shows that zinc ion produced by nano-ZnO and photocatalytic reaction make the fabrics have good antibacterial activity at low nano-ZnO content. When nano-ZnO concentration reaches 1.5 wt%, the antibacterial rate against Escherichia coli and Staphylococcus aureus reaches 98.52 % and 98.13 %, respectively.

Construction of high-performance and sustainable polylactic acid composites for 3D printing applications with plasticizer.

Polylactic acid (PLA) attains much attention because of its biodegradability, biocompatibility, and high strength, but its further application was remarkably hindered by its brittleness. In order to improve the toughness of PLA, a biodegradable composite was prepared by blending ductile polycaprolactone (PCL), stiff microcrystalline cellulose (MCC), and green plasticizer tributyl citrate (TBC) with PLA by melting extrusion. The physicochemical properties and microstructure of PLA composites were thoroughly investigated using FTIR, TGA, DSC, XRD, melting rheology, optical transmittance, 3d printing, tensile tests, and SEM. The tensile tests results show that introduction of TBC exhibited a remarkable improvement effect in the elongation at break of PLA/PCL/MCC (PPM) composite, increasing from 2.9 % of PPM to up to 30 % of PPM/6TBC and PPM/8TBC. Noticeably, the strength of PPM/TBC composites (at least 33.1 MPa) was enhanced compared with that of PPM (28.2 MPa). The plasticization of TBC, enhancing the compatibility of composites, and reinforcing effect of MCC were identified as pivotal factors in toughening and reinforcing PLA. Furthermore, it is observed that the incorporation of TBC contributed to enhanced thermal stability, crystallinity, and rheology property of composites. This research supplies a novel approach to bolstering the toughness of PLA and broaden its potential applications.

The effect of papaverine on tendon healing and adhesion in rats following Achilles tendon repair.

OBJECTIVES: The study aimed to examine the histopathological and biomechanical effects of papaverine administered intraperitoneally and locally on Achilles tendon healing in a rat model. MATERIALS AND METHODS: Forty-eight adult male Sprague-Dawley rats (range, 300 to 400 g) were used in this study conducted between October and November 2022. The rats were divided into three groups, with each group further subdivided into two for sacrifice on either the 15th (early period) or 30th (late period) day after surgery. The first (control) group received no treatment following Achilles tendon repair, while papaverine was intraperitoneally administered every other day for 10 days in the second group and locally in the third group after surgery. On the 15th and 30th days, the rats were sacrificed, and their Achilles tendons were subjected to biomechanical testing and histopathological evaluation. RESULTS: Histopathologically, there were no significant differences among the groups on the 15th day. However, on the 30th day, the locally applied papaverine group exhibited superior histopathological outcomes compared to the control group (p<0.05). Concerning the highest tensile strength values before rupture, the biomechanical assessment showed that the group receiving local papaverine treatment in the early period and both the group with systemic papaverine treatment and the one with local papaverine treatment in the late period displayed a statistically significant advantage compared to the control group (p<0.05). CONCLUSION: Locally administered papaverine has positive biomechanical effects in the early period and exhibits a positive correlation both histopathologically and biomechanically in the late period. Novel therapeutic options may be provided for patients through these findings.

An in vitro and in vivo study of electrospun polyvinyl alcohol/chitosan/sildenafil citrate mat on 3D-printed polycaprolactone membrane as a double layer wound dressing.

Double-layer dermal substitutes (DS) generally provide more effective therapeutic outcomes than single-layer substitutes. The architectural design of DS incorporates an outer layer to protect against bacterial invasions and maintain wound hydration, thereby reducing the risk of infection and the frequency of dressing changes. Moreover, the outer layer is a mechanical support for the wound, preventing undue tension in the affected area. A 3D-printed polycaprolactone (PCL) membrane was utilized as the outer layer to fabricate DS wound dressing. Simultaneously, a polyvinyl alcohol/chitosan/sildenafil citrate (PVA/CS/SC) scaffold was electrospun onto the PCL membrane to facilitate cellular adhesion and proliferation. Scanning electron microscopy (SEM) analysis of the PCL filaments revealed a consistent cross-sectional surface and structure, with an average diameter of 562.72 ±â€¯29.15 µm. SEM results also demonstrated uniform morphology and beadless structure for the PVA/CS/SC scaffold, with an average fiber diameter of 366.77 ±â€¯1.81 nm for PVA/CS. The addition of SC led to an increase in fiber diameter while resulting in a reduction in tensile strength. However, drug release analysis indicated that the SC release from the sample can last up to 72 h. Animal experimentation confirmed that DS wound dressing positively accelerated wound closure and collagen deposition in the Wistar rat skin wound model.

Towards scalable and degradable bioplastic films from Moringa oleifera gum/poly(vinyl alcohol) as packaging material.

The use of plant gum-based biodegradable bioplastic films as a packaging material is limited due to their poor physicochemical properties. However, combining plant gum with synthetic degradable polymer and some additives can improve these properties. Keeping in view, the present study aimed to synthesize a series of bioplastic films using Moringa oleifera gum, polyvinyl alcohol, glycerol, and citric acid via thermal treatment followed by a solution casting method. The films were characterized using analytical techniques such as FTIR, XRD, SEM, AFM, TGA, and DSC. The study examined properties such as water sensitivity, gas barrier attributes, tensile strength, the shelf life of food, and biodegradability. The films containing higher citric acid amounts showed appreciable %elongation without compromising tensile strength, good oxygen barrier properties, and biodegradation rates (>95%). Varying the amounts of glycerol and citric acid in the films broadened their physicochemical properties ranging from hydrophilicity to hydrophobicity and rigidity to flexibility. As all the films were synthesized using economical and environmentally safe materials, and showed better physicochemical and barrier properties, this study suggests that these bioplastic films can prove to be a potential alternative for various packaging applications.

The Effects of Reusing Cobalt-Chromium Alloy Powder on Its Mechanical Properties and Grain Size: An In Vitro Study.

PURPOSE: To characterize material changes that may occur in virgin cobalt-chromium (Co-Cr) alloy powder when it is blended with alloy powders that have been reused multiple times. MATERIALS AND METHODS: Initially, 20 kg of virgin Co-Cr powder was loaded into a laser-sintering device. The tensile test specimens were fabricated in the first (Group 1), fourth (Group 2), seventh (Group 3), tenth (Group 4), and thirteenth (Group 5) production cycles (N = 15). Prior to fabricating the specimens, powder alloy samples were collected from the powder bed for analysis. The tensile strength, elastic modulus, and percent elongation were calculated with tensile testing. Scanning electron microscopy and energy dispersive x-ray spectroscopy (SEM/EDS) and laser particle size distribution (LPSD) were used to analyze the alloy powder samples. The fracture surface of one tensile test specimen from each group was examined via SEM/EDS. One-way ANOVA followed by Dunnett T3 test was used for statistical analysis (α = .05). RESULTS: No difference was observed between groups in terms of tensile strength. A statistically significant difference was observed between Groups 1 and 2 in terms of percent elongation. Groups 2 and 4 were statistically significantly different in terms of both elastic modulus and percent elongation (P ≤ .05). SEM images of the powder alloy showed noticeable differences with increasing numbers of cycles. SEM images and the EDS analysis of the fractured specimens were in accordance with the strength data. CONCLUSIONS: Reusing Co-Cr alloy powder increased the particle size distribution. However, there was no correlation between increased cycle number and the mechanical properties of the powder.

Investigation on damage evolution mechanism of various FRP strengthened concrete subjected to chemical-freeze-thaw coupling erosion.

The corrosion resistance of FRP-reinforced ordinary concrete members under the combined action of harsh environments (i.e., alkaline or acidic solutions, salt solutions) and freeze-thaw cycles is still unclear. To study the mechanical and apparent deterioration of carbon/basalt/glass/aramid fiber cloth reinforced concrete under chemical and freeze-thaw coupling. Plain concrete blocks and FRP-bonded concrete blocks were fabricated. The tensile properties of the FRP sheet and epoxy resin sheet before and after chemical freezing, the compressive strength of the FRP reinforced test block, and the bending capacity of the prismatic test block pasted with FRP on the prefabricated crack side were tested. The deterioration mechanism of the test block was analyzed through the change of surface photos. Based on the experimental data, the Lam-Teng constitutive model of concrete reinforced by alkali-freeze coupling FRP is modified. The results indicate that, in terms of apparent properties, with the increase in the duration of chemical freeze-thaw erosion, the surface of epoxy resin sheets exhibits an increase in pores, along with the emergence of small cracks and wrinkles. The texture of FRP sheets becomes blurred, and cracks and wrinkles appear on the surface. In terms of failure modes, as the number of chemical coupling erosion cycles increases, the location of failure in epoxy resin sheets becomes uncertain, and the failure plane tilts towards the direction of the applied load. The failure mode of FRP sheets remains unchanged. However, the bonding strength between FRP sheets and concrete decreases, resulting in a weakened reinforcement effect. In terms of mechanical properties, FRP sheets undergo the most severe degradation in the coupled environment of acid freeze-thaw cycles. Among them, GFRP experiences the largest degradation in tensile strength, reaching up to 30.17%. In terms of tensile performance, the sheets rank from highest to lowest as follows: CFRP, BFRP, AFRP, and GFRP.As the duration of chemical freeze-coupled erosion increases, the loss rate of compressive strength for specimens bonded with CFRP is the smallest (9.62% in salt freeze-thaw environment), while the loss rate of bearing capacity is higher for specimens reinforced with GFRP (33.8% in acid freeze-thaw environment). In contrast, the loss rate of bearing capacity is lower for specimens reinforced with CFRP (13.6% in salt freeze-thaw environment), but still higher for specimens reinforced with GFRP (25.8% in acid freeze-thaw environment).