Enhanced charge-carrier dynamics and efficient solar-to-urea conversion on Si-based photocathodes.

Photoelectrochemical (PEC) coupling of CO2 and nitrate can provide a useful and green source of urea, but the process is affected by the photocathodes with poor charge-carrier dynamics and low conversion efficiency. Here, a NiFe diatomic catalysts/TiO2 layer/nanostructured n+p-Si photocathode is rationally designed, achieving a good charge-separation efficiency of 78.8% and charge-injection efficiency of 56.9% in the process of PEC urea synthesis. Compared with the electrocatalytic urea synthesis by using the same catalysts, the Si-based photocathode shows a similar urea yield rate (81.1 mg·h-1·cm-2) with a higher faradic efficiency (24.2%, almost twice than the electrocatalysis) at a lower applied potential under 1 sun illumination, meaning that a lower energy-consumption method acquires more aimed productions. Integrating the PEC measurements and characterization results, the synergistic effect of hierarchical structure is the dominating factor for enhancing the charge-carrier separation, transfer, and injection by the matched band structure and favorable electron-migration channels. This work provides a direct and efficient route of solar-to-urea conversion.

Non-Covalent Interaction Enhancement on Active/Interfacial Layers via Two-Dimensional Vermiculite Doping for Efficient Organic Solar Cells.

Interface modification plays an important role in improving the power conversion efficiency (PCE) of organic solar cells (OSCs). However, the low non-covalent interaction between the cathode interface layer (CIL) and nonfullerene acceptor (NFA) directly affects the charge collection of OSCs. Here, the non-covalent interaction between the CIL and NFA is enhanced by introducing the 2D vermiculite (VML) in the poly(9,9-bis(3'-(N,N-dimethyl)-Nethylammonium-propyl-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)) dibromide (PFN-Br) interface layer to form an efficient electron transport channel. As a result, the electron extraction efficiency from the active layer to the CIL is increased, and the PCE of OSCs based on PBDB-T:ITIC is boosted from 10.87% to 12.89%. In addition, the strategy of CIL doping VML is proven to be universal in different CIL materials, for which the PCE is boosted from 10.21% to 11.57% for OSCs based on PDINN and from 9.82% to 11.27% for OSCs based on PNDIT-F3N. The results provide a viable option for designing efficient CIL for high-performance non-fullerene OSCs, which may promote the commercialization of OSCs.

Work Function Tuning of Carbon Electrode to Boost the Charge Extraction in Hole Transport Layer-Free Perovskite Solar Cells.

Perovskite solar cell (PSC) is a promising photovoltaic technology that achieves over 26% power conversion efficiency (PCE). However, the high materials costs, complicated fabrication process, as well as poor long-term stability, are stumbling blocks for the commercialization of the PSCs in normal structures. The hole transport layer (HTL)-free carbon-based PSCs (C-PSCs) are expected to overcome these challenges. However, C-PSCs have suffered from relatively low PCE due to severe energy loss at the perovskite/carbon interface. Herein, the study proposes to boost the hole extraction capability of carbon electrode by incorporating functional manganese (II III) oxide (Mn3O4). It is found that the work function (WF) of the carbon electrode can be finely tuned with different amounts of Mn3O4 addition, thus the interfacial charge transfer efficiency can be maximized. Besides, the mechanical properties of carbon electrode can also be strengthened. Finally, a PCE of 19.03% is achieved. Moreover, the device retains 90% of its initial PCE after 2000 h of storage. This study offers a feasible strategy for fabricating efficient paintable HTL-free C-PSCs.

SnSe2 Quantum Dots and Chlorhexidine Acetate Suppress Synergistically Non-radiative Recombination Loss for High Efficiency and Stability Perovskite Solar Cells.

Non-radiative recombination losses limit the property of perovskite solar cells (PSCs). Here, a synergistic strategy of SnSe2QDs doping into SnO2 and chlorhexidine acetate (CA) coating on the surface of perovskite is proposed. The introduction of 2D SnSe2QDs reduces the oxygen vacancy defects and increases the carrier mobility of SnO2. The optimized SnO2 as a buried interface obviously improves the crystallization quality of perovskite. The CA containing abundant active sites of ─NH2/─NH─, ─C═N, CO, ─Cl groups passivate the defects on the surface and grain boundary of perovskite. The alkyl chain of CA also improves the hydrophobicity of perovskite. Moreover, the synergism of SnSe2QDs and CA releases the residual stress and regulates the energy level arrangement at the top and bottom interface of perovskite. Benefiting from these advantages, the bulk and interface non-radiative recombination loss is greatly suppressed and thereby increases the carrier transport and extraction in devices. As a result, the best power conversion efficiency (PCE) of 23.41% for rigid PSCs and the best PCE of 21.84% for flexible PSCs are reached. The rigid PSC maintains 89% of initial efficiency after storing nitrogen for 3100 h. The flexible PSCs retain 87% of the initial PCE after 5000 bending cycles at a bending radius of 5 mm.

Efficient Photothermal Sensor Based on Coral-Like Hollow Gold Nanospheres for the Sensitive Detection of Sulfonamides.

Gold nanoparticles (AuNPs), universally regarded as colorimetric signal reporters, are widely employed in lateral flow immunoassays (LFIAs). However, it is difficult for AuNPs-LFIA to achieve a wide range and sensitive detection. Herein, novel coral-like hollow gold nanospheres (CHGNPs) are synthesized. The growth of gold nanospheres can be regulated to obtain a multibranched and hollow construction. The obtained CHGNPs possess intense broadband absorption across the visible to near-infrared region, exhibiting a high molar extinction coefficient of 14.65 × 1011 M-1 cm-1 and a photothermal conversion efficiency of 79.75%. Thus, the photothermal/colorimetric dual-readout LFIA is developed based on CHGNPs (CHGNPs-PT-LFIA and CHGNPs-CM-LFIA) to effectively improve the detection sensitivity and broaden the detection range in regard to sulfonamides (SAs). The limits of detection of the CHGNPs-PT-LFIA and CHGNPs-CM-LFIA reached 1.9 and 2.8 pg mL-1 for the quantitative detection of sulfaquinoxaline, respectively, which are 6.3-fold and 4.3-fold lower than that of the AuNPs-LFIA. Meanwhile, the CHGNPs-PT-LFIA broadened the detection range to three orders of magnitude, which ranged from 2.5 to 5000 pg mL-1. The synthesized photothermal CHGNPs have been proven effective in improving the performance of the LFIA and provide a potential option for the construction of sensing platforms.

In Situ Photogenerated Radicals of Hydroxyl Substituted Pyrene-Based Triphenylamines with Enhanced Transport and Free Doping/Post-Oxidation for Efficient Perovskite Solar Cells.

The high-performance hole transporting material (HTM) is one of the most important components for the perovskite solar cells (PSCs) in promoting power conversion efficiency (PCE). However, the low conductivity of HTMs and their additional requirements for doping and post-oxidation greatly limits the device performance. In this work, three novel pyrene-based derivatives containing methoxy-substituted triphenylamines units (PyTPA, PyTPA-OH and PyTPA-2OH) are designed and synthesized, where different numbers of hydroxyl groups are connected at the 2- or 2,7-positions of the pyrene core. These hydroxyl groups at the 2- or 2,7-positions of pyrene play a significantly role to enhance the intermolecular interactions that are able to generate in situ radicals with the assistance of visible light irradiation, resulting in enhanced hole transferring ability, as well as an enhanced conductivity and suppressed recombination. These pyrene-core based HTMs exhibit excellent performance in PSCs, which possess a higher PCE than those control devices using the traditional spiro-OMeTAD as the HTM. The best performance can be found in the devices with PyTPA-2OH. It has an average PCE of 23.44% (PCEmax = 23.50%), which is the highest PCE among the reported PSCs with the pyrene-core based HTMs up to date. This research offers a novel avenue to design a dopant-free HTM by the combination of the pyrene core, methoxy triphenylamines, and hydroxy groups.

Tailoring the Molecular Planarity of Perylene Diimide-Based Third Component toward Efficient Ternary Organic Solar Cells.

Incorporating a third component into binary organic solar cells (b-OSCs) has provided a potential platform to boost power conversion efficiency (PCEs). However, gaining control over the non-equilibrium blend morphology via the molecular design of the perylene diimide (PDI)-based third component toward efficient ternary organic solar cells (t-OSCs) still remains challenging. Herein, two novel PDI derivatives are developed with tailored molecular planarity, namely ufBTz-2PDI and fBTz-2PDI, as the third component for t-OSCs. Notably, after performing a cyclization reaction, the twisted ufBTz-2PDI with an amorphous character transferred to the highly planar fBTz-2PDI followed by a semi-crystalline character. When incorporating the semi-crystalline fBTz-2PDI into the D18:L8-BO system, the resultant t-OSC achieved an impressive PCE of 18.56%, surpassing the 17.88% attained in b-OSCs. In comparison, the addition of amorphous ufBTz-2PDI into the binary system facilitates additional charge trap sites and results in a deteriorative PCE of 14.37%. Additionally, The third component fBTz-2PDI possesses a good generality in optimizing the PCEs of several b-OSCs systems are demonstrated. The results not only provided a novel A-DA'D-A motif for further designing efficient third component but also demonstrated the crucial role of modulated crystallinity of the PDI-based third component in optimizing PCEs of t-OSCs.

Reducing Domain Density Enhances Conversion Efficiency in GeTe.

Incorporating dilute doping and controlled synthesis provides a means to modulate the microstructure, defect density, and transport properties. Transmission electron microscopy (TEM) and geometric phase analysis (GPA) have revealed that hot-pressing can increase defect density, which redistributes strain and helps prevent unwanted Ge precipitates formation. An alloy of GeTe with a minute amount of indium added has shown remarkable TE properties compared to its undoped counterpart. Specifically, it achieves a maximum figure-of-merit zT of 1.3 at 683 K and an exceptional TE conversion efficiency of 2.83% at a hot-side temperature of 723 K. Significant zT and conversion efficiency improvements are mainly due to domain density engineering facilitated by an effective hot-pressing technique applied to lightly doped GeTe. The In-GeTe alloy exhibits superior TE properties and demonstrates notable stability under significant thermal gradients, highlighting its promise for use in mid-temperature TE energy generation systems.

A Difluoro-Methoxylated Ending-Group Asymmetric Small Molecule Acceptor Lead Efficient Binary Organic Photovoltaic Blend.

Developing a new end group for synthesizing asymmetric small molecule acceptors (SMAs) is crucial for achieving high-performance organic photovoltaics (OPVs). Herein, an asymmetric small molecule acceptor, BTP-BO-4FO, featuring a new difluoro-methoxylated end-group is reported. Compared to its symmetric counterpart L8-BO, BTP-BO-4FO exhibits an upshifted energy level, larger dipole moment, and more sequential crystallinity. By adopting two representative and widely available solvent additives (1-chloronaphthalene (CN) and 1,8-diiodooctane (DIO)), the device based on PM6:BTP-BO-4FO (CN) photovoltaic blend demonstrates a power conversion efficiency (PCE) of 18.62% with an excellent open-circuit voltage (VOC) of 0.933 V, which surpasses the optimal result of L8-BO. The PCE of 18.62% realizes the best efficiencies for binary OPVs based on SMAs with asymmetric end groups. A series of investigations reveal that optimized PM6:BTP-BO-4FO film demonstrates similar molecular packing motif and fibrillar phase distribution as PM6:L8-BO (DIO) does, resulting in comparable recombination dynamics, thus, similar fill factor. Besides, it is found PM6:BTP-BO-4FO possesses more efficient charge generation, which yields better VOC-JSC balance. This study provides a new ending group that enables a cutting-edge efficiency in asymmetric SMA-based OPVs, enriching the material library and shed light on further design ideas.

Elimination of Intragrain Defect to Enhance the Performance of FAPbI3 Perovskite Solar Cells by Ionic Liquid.

Ionic liquids have been widely used to improve the efficiency and stability of perovskite solar cells (PSCs), and are generally believed to passivate defects on the grain boundaries of perovskites. However, few studies have focused on the relevant effects of ionic liquids on intragrain defects in perovskites which have been shown to be critical for the performance of PSCs. In this work, the effect of ionic liquid 1-hexyl-3-methylimidazolium iodide (HMII) on intragrain defects of formamidinium lead iodide (FAPbI3) perovskite is investigated. Abundant {111}c intragrain planar defects in pure FAPbI3 grains are found to be significantly reduced by the addition of the ionic liquid HMII, shown by using ultra-low-dose selected area electron diffraction. As a result, longer charge carrier lifetimes, higher photoluminescence quantum yield, better charge carrier transport properties, lower Urbach energy, and current-voltage hysteresis are achieved, and the champion power conversion efficiency of 24.09% is demonstrated. These observations suggest that ionic liquids significantly improve device performance resulting from the elimination of {111}c intragrain planar defects.

A 3,3'-Difluoro-2,2'-Bithiophene Based Donor Polymer Realizing High Efficiency (>17%) Single Junction Binary Organic Solar Cells.

In this study, two novel donor-acceptor (D-A) copolymers are designed and synthesized, DTBT-2T and DTBT-2T2F with 2,2'-bithiophene or 3,3'-difluoro-2,2'-bithiophene as the donor unit and dithienobenzothiadiazole as the acceptor unit, and used them as donor materials in non-fullerene organic solar cells (OSCs). Due to enhanced planarity of polymer chains resulted by the intramolecular F···S noncovalent interactions, the incorporation of 3,3'-difluoro-2,2'-bithiophene unit instead of 2,2'-bithiophene into the polymers can enhance their molecular packing, crystallinity and hole mobility. The DTBT-2T:L8-BO based binary OSCs deliver a power conversion efficiency (PCE) of only 9.71% with a Voc of 0.78 V, a Jsc of 20.69 mA cm-2 , and an FF of 59.67%. Moreover, the introduction of fluoro atoms can lower the highest occupied molecular orbital levels. As a result, DTBT-2T2F:L8-BO based single-junction binary OSCs exhibited less recombination loss, more balanced charge mobility, and more favorable morphology, resulting in an impressive PCE of 17.03% with a higher Voc of 0.89 V, a Jsc of 25.40 mA cm-2, and an FF of 75.74%. These results indicate that 3,3'-difluoro-2,2'-bithiophene unit can be used as an effective building block to synthesize high performance polymer donor materials. This work greatly expands the selection range of donor units for constructing high-performance polymers.

Photo-Rechargeable Asymmetric Supercapacitors Exceeding Light-to-Charge Storage Efficiency over 21% under Indoor Light.

Photo-rechargeable energy storage devices are appealing for substantial research attention because of their possible applications in the Internet of Things (IoT) and low-powered miniaturized portable electronics. However, due to the incompatibility of the photovoltaics and energy storage systems (ESSs), the overall light-to-storage efficiency is limited under indoor light conditions. Herein, a porous carbon scaffold MnO-Mn3 O4 /C microsphere-based monolithic dye-sensitized photo-rechargeable asymmetric supercapacitor (DSPC) is fabricated. The integrated DSPC has a high areal specific capacitance of 281.9 mF cm-2 at the discharge rate of 0.01 mA cm-2 . The light-to-electrical conversion efficiency of the DSSC is 27.6% under the 1000 lux compact fluorescent lamp (CFL). The DSPC shows an outstanding light-to-charge storage efficiency of 21.6%, which is higher than that reported ever. Furthermore, the fabricated polymer gel electrolyte-based quasi-solid state (QSS) DSPC shows similar overall conversion efficiency with superior cycling capability. This work shows a convenient fabrication process for a wireless power pack of interest with outstanding performance.

Halogenated 9H-Indeno[1,2-b]Pyrazine-2,3-Dicarbonitrile End Groups Based Asymmetric Non-Fullerene Acceptors for Green Solvent-Processable, Additive-Free, and Stable Organic Solar Cells.

Non-fullerene acceptors (NFAs) significantly enhance photovoltaic performance in organic solar cells (OSCs) using halogenated solvents and additives. However, these solvents are environmentally detrimental and unsuitable for industrial-scale production, and the issue of OSCs' poor long-term stability persists. This report introduces eight asymmetric NFAs (IPCnF-BBO-IC2F, IPCnF-BBO-IC2Cl, IPCnCl-BBO-IC2F, and IPCnCl-BBO-IC2Cl, where n = 1 and 2). These NFAs comprise a 12,13-bis(2-butyloctyl)-3,9-diundecyl-12,13-dihydro-[1,2,5]thiadiazolo[3,4-e]thieno[2'',3'':4',5']thieno[2',3':4,5]pyrrolo[3,2-g]thieno[2',3':4,5]thieno-[3,2-b]indole (BBO) core. One end of the core attaches to a mono- or di-halogenated 9H-indeno[1,2-b]pyrazine-2,3-dicarbonitrile (IPC) end group (IPC1F, IPC1Cl, IPC2F, or IPC2Cl), while the other end connects to a 2-(5,6-dihalo-3-oxo-2,3-dihydro-1H-inden-1-ylidene)malononitrile (IC) end group (IC2F or IC2Cl). The optical and electronic properties of these NFAs can be finely tuned by controlling the number of halogen atoms. Crucially, these NFAs demonstrate excellent compatibility with PM6 even in o-xylene, facilitating the production of additive-free OSCs. The di-halogenated IPC-based NFAs outperform their mono-halogenated counterparts in photovoltaic performance within OSCs. Remarkably, the di-halogenated IPC-based NFAs maintain 94‒98% of their initial PCEs over 2000 h in air without encapsulation, indicating superior long-term device stability. These findings imply that the integration of di-halogenated IPCs in asymmetric NFA design offers a promising route to efficient, stable OSCs manufactured through environmentally friendly processes.

13C-labeling reveals non-conventional pathways providing carbon for hydroxy fatty acid synthesis in Physaria fendleri.

Physaria fendleri is a member of the Brassicaceae that produces in its embryos hydroxy fatty acids, constituents of oils that are very valuable and widely used by industry for cosmetics, lubricants, biofuels, etc. Free of toxins and rich in hydroxy fatty acids, Physaria provides a promising alternative to imported castor oil and is on the verge of being commercialized. This study aims to identify important biochemical step(s) for oil synthesis in Physaria, which may serve as target(s) for future crop improvement. To advance towards this goal, the endosperm composition was analysed by LC-MS/MS to develop and validate culture conditions that mimic the development of the embryos in planta. Using developing Physaria embryos in culture and 13C-labeling, our studies revealed that: (i) Physaria embryos metabolize carbon into biomass with an efficiency significantly lower than other photosynthetic embryos; (ii) the plastidic malic enzyme provides 42% of the pyruvate used for de novo fatty acid synthesis, which is the highest measured so far in developing 'green' oilseed embryos; and (iii) Physaria uses non-conventional pathways to channel carbon into oil, namely the Rubisco shunt, which fixes CO2 released in the plastid, and the reversibility of isocitrate dehydrogenase, which provides additional carbon for fatty acid elongation.

Phenylethylammonium bromide-assisted solution-phase ligand exchange in CsPbBr3quantum dot solar cells.

CsPbBr3quantum dots (QDs) have excellent optical properties and good phase stability, but the long-chain ligands on their surfaces affect the charge transfer between QDs. Here, we propose a simple ligand exchange strategy: solution-phase ligand exchange. By adding an acetone solution of phenylethylammonium bromide to the purification process of CsPbBr3QDs, the long-chain ligands were effectively replaced and the electric coupling between QDs was improved. As a result, the power conversion efficiency of the solar cell was increased from 1.95% to 2.83%. Meanwhile, the stability of the devices was significantly improved in the unencapsulated case.

Temperature-Switch-Controlled Second Harmonic Mode Sensor for Brain-Tissue Detection.

Identifying brain-tissue types holds significant research value in the biomedical field of non-contact brain-tissue measurement applications. In this paper, a layered metastructure is proposed, and the second harmonic generation (SHG) in a multilayer metastructure is derived using the transfer matrix method. With the SHG conversion efficiency (CE) as the measurement signal, the refractive index ranges that can be distinguished are 1.23~1.31 refractive index unit (RIU) and 1.38~1.44 RIU, with sensitivities of 0.8597 RIU-1 and 1.2967 RIU-1, respectively. It can distinguish various brain tissues, including gray matter, white matter, and low-grade glioma, achieving the function of a second harmonic mode sensor (SHMS). Furthermore, temperature has a significant impact on the SHG CE, which can be used to define the switch signal indicating whether the SHMS is functioning properly. When the temperature range is 291.4~307.9 Kelvin (K), the temperature switch is in the "open" state, and the optimal SHG CE is higher than 0.298%, indicating that the SHMS is in the working state. For other temperature ranges, the SHG CE will decrease significantly, indicating that the temperature switch is in the "off" state, and the SHMS is not working. By stimulating temperature and using the response of SHG CE, the temperature-switch function is achieved, providing a new approach for temperature-controlled second harmonic detection.

Synthesis and Photovoltaic Performance of ß-Amino-Substituted Porphyrin Derivatives.

New ß-amino-substituted porphyrin derivatives bearing carboxy groups were synthesized and their performance as sensitizers in dye-sensitized solar cells (DSSC) was evaluated. The new compounds were obtained in good yields (63-74%) through nucleophilic aromatic substitution reactions with 3-sulfanyl- and 4-sulfanylbenzoic acids. Although the electrochemical studies indicated suitable HOMO and LUMO energy levels for use in DSSC, the devices fabricated with these compounds revealed a low power conversion efficiency (PCE) that is primarily due to the low open-circuit voltage (Voc) and short-circuit current density (Jsc) values.

Enhanced Photovoltaic Performance of Asymmetrical Benzo Dithiophene Homopolymer Donor Materials in Nonfullerene Acceptor-Based Organic Photovoltaics.

Although much promising synthetic progress in conjugated polymer-based organic solar cells (OSCs) has resulted in significant improvement in power conversion efficiencies (PCEs) of from over 15 to >19.0% in the last five years, the sophisticated and complex reactions from at least two families' monomers with remarkably different electron push-pull effects could still pose an unavoidable material burden for the commercialization of OSCs in the coming future. Therefore, the method of preparing a homopolymer from a sole monomer would significantly reduce the synthetic steps and costs in order to pave the way for the large-scale production of OSC materials. Therefore, alkylthio-thiophenyl-substituted benzo[1,2-b;4,5-b']dithiophene (BDTTS) as the sole and key structural moiety with dihalogen and distannyl functional groups was designed and synthesized, respectively, in this study, for facile monomer syntheses and polymerizations to achieve three wide-bandgap homopolymer donors of BDTTS-alt-BDTT-Cl (P13), BDTTS-alt-BDTT (P15), and BDTTS (P14), respectively. The structural symmetry dependency on their physical, electrochemical, and optical properties, thin-film morphologies, and photovoltaic (PV) performance was investigated in detail. As a result, OSCs based on the asymmetric polymer P15, paired with BTP-eC9 as the electron acceptor, presented the best PV performance, with a PCE of 11.5%, a fill factor (FF) of 65.87%, and a short-circuit current (JSC) of 22.04 mA·cm-2, respectively. This PCE value is among the highest ones reported for BDT-type homopolymer donor-based OPVs, providing us with knowledge for obtaining promising PV performance from devices made of P15-like materials.

Effect of stocking density on performance, survival and nutrient composition of super worm Zophobas Morio (Coleoptera:Tenebrionidae).

As the global demand for animal protein continues to increase, the need for sustainable and resource-efficient alternatives for animal feed becomes increasingly paramount. Insects have gained significant attention as promising candidates to support the sustainable development of the feed industry, and their utilization in animal feed has seen substantial growth in recent years. Therefore, this study was conducted to optimize the superworm (Zophobas morio) larvae rearing stocking density on the biomass production, survival, and nutrient composition. Two-weeks-old Z. morio larvae were maintained at 25 ± 2 oC and 70% relative humidity, and at densities of 0.5, 0.75, 1 and 1.25 cm2 space per larva, respectively. The insects reared with a density of 1.25 cm2 per larvae had higher feed intake (FI) and weight gain (WG) (P < 0.05). However, better feed conversion efficiency (FCE) was recorded with a density of 0.75 cm2 per larvae (P < 0.05). The survival significantly increased with increasing the density per larvae (P < 0.05). High survival of Z. morio larvae was recorded at density of 1 and 1.25 cm2 per larvae. The dry matter and fat contents of Z. morio larvae were higher at density of 0.5 cm2 per larvae (P < 0.05). However, the protein content was higher at density of 1 and 1.25 cm2 per larvae (P < 0.05). Moreover, the ash content was higher at 0.5, 0.75, and 1.25 cm2 per larvae (P < 0.05). This study highlights that Z. morio larvae rearing stocking density has a profound influence on growth performance, survival and its nutrient composition.

Ethylenedioxythiophene-Based Small Molecular Donor with Multiple Conformation Locks for Organic Solar Cells with Efficiency of 19.3 .

Ternary organic solar cells (T-OSCs) represent an efficient strategy for enhancing the performance of OSCs. Presently, the majority of high-performance T-OSCs incorporates well-established Y-acceptors or donor polymers as the third component. In this study, a novel class of conjugated small molecules has been introduced as the third component, demonstrating exceptional photovoltaic performance in T-OSCs. This innovative molecule comprises ethylenedioxythiophene (EDOT) bridge and 3-ethylrhodanine as the end group, with the EDOT unit facilitating the creation of multiple conformation locks. Consequently, the EDOT-based molecule exhibits two-dimensional charge transport, distinguishing it from the thiophene-bridged small molecule, which displays fewer conformation locks and provides one-dimensional charge transport. Furthermore, the robust electron-donating nature of EDOT imparts the small molecule with cascade energy levels relative to the electron donor and acceptor. As a result, OSCs incorporating the EDOT-based small molecule as the third component demonstrate enhanced mobilities, yielding a remarkable efficiency of 19.3 %, surpassing the efficiency of 18.7 % observed for OSCs incorporating thiophene-based small molecule as the third component. The investigations in this study underscore the excellence of EDOT as a building block for constructing conjugated materials with multiple conformation locks and high charge carrier mobilities, thereby contributing to elevated photovoltaic performance in OSCs.