RESUMO
The solubility of glibenclamide was evaluated in DMSO, NMP, 1,4-dioxane, PEG 400, Transcutol® HP, water, and aqueous mixtures (T = 293.15~323.15 K). It was then recrystallized to solvate and compressed into tablets, of which 30-day stability and dissolution was studied. It had a higher solubility in 1,4-dioxane, DMSO, NMP (Xexp = 2.30 × 103, 3.08 × 104, 2.90 × 104) at 323.15 K, its mixture (Xexp = 1.93 × 103, 1.89 × 104, 1.58 × 104) at 298.15 K, and 1,4-dioxane (w) + water (1-w) mixture ratio of w = 0.8 (Xexp = 3.74 × 103) at 323.15 K. Modified Apelblat (RMSD ≤ 0.519) and CNIBS/R-K model (RMSD ≤ 0.358) suggested good comparability with the experimental solubility. The minimum value of ΔG° vs ΔH° at 0.70 < x2 < 0.80 suggested higher solubility at that molar concentration. Based on the solubility, it was recrystallized into the solvate, which was granulated and compressed into tablets. Among the studied solvates, the tablets of glibenclamide dioxane solvate had a higher initial (95.51%) and 30-day (93.74%) dissolution compared to glibenclamide reference (28.93%). There was no stability issue even after granulation, drying, or at pH 7.4. Thus, glibenclamide dioxane solvate could be an alternative form to improve the molecule's properties.
Assuntos
Liberação Controlada de Fármacos , Glibureto/química , Glibureto/farmacologia , Termodinâmica , Cromatografia Líquida de Alta Pressão , Cristalização , Estabilidade de Medicamentos , Estrutura Molecular , Solubilidade , Solventes/química , Análise EspectralRESUMO
The multi-dose vial (MDV) is widely used for most biopharmaceuticals that are repackaged in plastic syringes before use. However, subvisible particle formation with the use of plastic syringes containing silicone oil (SO syringes) for handling therapeutic proteins can be problematic. This study aimed to evaluate the extent of and trends in microparticle (>1 µm) formation and accumulation in repackaged syringes from MDVs containing human immunoglobulin (IgG) and lipid nanoparticles (LNPs). Light obscuration (LO) and flow imaging (FI) were used to analyze the microparticles. The number of microparticles observed with the use SO syringes was greater than that with SO-free syringes, and the number of microparticles continuously increased as did the number of times of repackaging in syringes for both drugs. However, a large variation was observed across different brands of SO syringes. In contrast, using a different technique of drug withdrawal from the vial significantly reduced the number of microparticles. Furthermore, the use of filter-integrated needles or the inclusion of stabilizers such as acetyl-arginine and Tween 20 into the formulation also helped reduce particle formation.
Assuntos
Imunoglobulinas , Seringas , Humanos , Bevacizumab , PlásticosRESUMO
The effects of the manufacturing process and the regeneration of Shirasu porous glass (SPG) membranes were investigated on the reproducibility of protein precipitants, termed protein microbeads. Intravenous immunoglobulin (IVIG) was selected as a model protein to produce its microbeads in seven different cases. The results showed that the hydrophobically modified SPG membrane produced finer microbeads than the hydrophilic SPG membrane, but this was inconsistent when using the general regeneration method. Its reproducibility was determined to be mostly dependent on rinsing the SPG membrane prior to the modification and on the protein concentration used for emulsification. The higher concentration could foul and plug the membrane during protein release and thus the membrane must be washed thoroughly before hydrophobic modification. Moreover, the membrane regenerated by silicone resin dissolved in ethanol had better reproducibility than silicone resin dissolved in water. On the other hand, rinsing the protein precipitant with cold ethanol after the emulsification was not favorable and induced protein aggregation. With the addition of trehalose, the purity of the IVIG microbeads was almost the same as before microbeadification. Therefore, the regeneration method, protein concentration, and its stabilizer are key to the success of protein emulsification and precipitation using the SPG membrane.