New Insights into Aggregation Behaviors of the UV-Irradiated Dissolved Biochars (DBioCs) in Aqueous Environments: Effects of Water Chemistries and Variation in the Hamaker Constant.

The aggregation behavior of ubiquitous dissolved black carbon (DBC) largely affects the fate and transport of its own contaminants and the attached contaminants. However, the photoaging processes and resulting effects on its colloidal stability remain yet unknown. Herein, dissolved biochars (DBioCs) were extracted from common wheat straw biochar as a proxy for an anthropogenic DBC. The influences of UV radiation on their aggregation kinetics were systematically investigated under various water chemistries (pH, electrolytes, and protein). The environmental stability of the DBioCs before and after radiation was further verified in two natural water samples. Hamaker constants of pristine and photoaged DBioCs were derived according to Derjaguin-Landau-Verwey-Overbeek (DLVO) prediction, and its attenuation (3.19 ± 0.15 × 10-21 J to 1.55 ± 0.07 × 10-21 J after 7 days of radiation) was described with decay kinetic models. Pearson correlation analysis revealed that the surface properties and aggregation behaviors of DBioCs were significantly correlated with radiation time (p < 0.05), indicating its profound effects. Based on characterization and experimental results, we proposed a three-stage mechanism (contended by photodecarboxylation, photo-oxidation, and mineral exposure) that DBioCs might experience under UV radiation. These findings would provide an important reference for potential phototransformation processes and relevant behavioral changes that DBC may encounter.

Analytical theory for the crossover from retarded to non-retarded interactions between metal plates.

The van der Waals force established between two surfaces plays a central role in many phenomena, such as adhesion or friction. However, the dependence of this forces on the distance of separation between plates is very complex. Two widely different non-retarded and retarded regimes are well known, but these have been traditionally studied separately. Much less is known about the important experimentally accessible cross-over regime. In this study, we provide analytical approximations for the van der Waals forces between two plates that interpolates exactly between the short distance and long distance behavior, and provides new insight into the crossover from London to Casimir forces at finite temperature. At short distance, where the behavior is dominated by non-retarded interactions, we work out a very accurate simplified approximation for the Hamaker constant which adopts analytical form for both the Drude and Lorentz models of dielectric response. We apply our analytical expressions for the study of forces between metallic plates, and observe very good agreement with exact results from numerical calculations. Our results show that contributions of interband transitions remain important in the experimentally accessible regime of decades nm for several metals, including gold.

Novel analytical expressions for determining van der Waals interaction between a particle and air-water interface: Unexpected stronger van der Waals force than capillary force.

HYPOTHESIS: Analytical expressions for calculating Hamaker constant (HC) and van der Waals (VDW) energy/force for interaction of a particle with a solid water interface has been reported for over eighty years. This work further developed novel analytical expressions and numerical approaches for determining HC and VDW interaction energy/force for the particle approaching and penetrating air-water interface (AWI), respectively. METHODS: The expressions of HC and VDW interaction energy/force before penetrating were developed through analysis of the variation in free energy of the interaction system with bringing the particle from infinity to the vicinity of the AWI. The surface element integration (SEI) technique was modified to calculate VDW energy/force after penetrating. FINDINGS: We explain why repulsive VDW energy exists inhibiting the particle from approaching the AWI. We found very significant VDW repulsion for a particle at a concave AWI after penetration, which can even exceed the capillary force and cause strong retention in water films on a solid surface and at air-water-solid interface line. The methods and findings of this work are critical to quantification and understanding of a variety of engineered processes such as particle manipulation (e.g., bubble flotation, Pickering emulsion, and particle laden interfaces).

Influence of humectants on the thermotropic behaviour and nanostructure of fully hydrated lecithin bilayers.

Humectants are used widely in topical formulations as they provide cosmetic and health benefits to skin. Of particular interest to our laboratories is the interaction of humectants in phospholipid based topical skin care formulations. This study probed the effects of three exemplary humectants on a fully hydrated lecithin system (DPPC) by use of X-ray scattering and differential scanning calorimetry. While the three humectants affected the nanostructure of 1, 2-dipalmitoyl-sn-glycero-3-phosphocholine, DPPC, bilayers in a similar manner, leading to an increased membrane order, differences in the effect on the thermal behaviour of DPPC suggest that betaine and sarcosine interacted via a different mechanism compared to acetic monoethanolamide, AMEA. At concentrations above 0.4 M, betaine and sarcosine stabilised the gel phase by depletion of the interfacial water via the preferential exclusion mechanism. At the same time, a slight increase in the rigidity of the membrane was observed with an increase in the membrane thickness. Overall, the addition of betaine or sarcosine resulted in an increase in the pre- and main transition temperatures of DPPC. AMEA, on the other hand, decreases both transition temperatures, and although the interlamellar water layer was also decreased, there was evidence from the altered lipid chain packing, that AMEA molecules are present also at the bilayer interface, at least at high concentrations. Above the melting point in the fluid lamellar phase, none of the humectants induced significant structural changes, neither concerning the bilayer stacking order nor its overall membrane fluidity. An humectant-induced increase in the Hamaker constant is the most plausible explanation for the observed reduction of the inter-bilayer distances, both in the gel and fluid phase.

Observation of interaction forces by investigation of the influence of eluent additives on the retention behavior of aqueous nanoparticle dispersions in asymmetrical flow field-flow fractionation.

The investigation and subsequent understanding of the interactions of nanomaterials with components of their surrounding media is important to be able to evaluate both potential use cases as well as potential risks for human health and for the environment. To investigate such interactions, asymmetrical flow field-flow fractionation (AF4) is an interesting analytical tool. This statement grounds on the fact that interactions of the analyte with the membrane and with components of the eluent are crucial for the retention behavior of the analyte within the field-flow fractionation (FFF) channel. Therefore, the investigation of the retention behavior provides an insight in the nature of the interactions between analyte, membrane and eluent. Within this publication, the influence of the composition of the eluent on the retention behavior of aqueous dispersions of two model analytes is investigated. Eluents with different types of salts and surfactants and eluents with different salt concentrations were prepared and the influence of the composition of these eluents on the retention behavior of polystyrene and polyorganosiloxane particles was compared. Three main trends were observed: Elution times increase with increasing electrolyte concentration; when comparing different electrolyte anions, the retention time increases the more kosmotropic the anion is; when comparing different electrolyte cations, the retention order depends on the surfactant. Additional dynamic light scattering (DLS) measurements were conducted to verify that the differences in retention times are not caused by actual differences in particle size. Instead, the differences in elution time can be correlated with the concentration and with the chao-/kosmotropicity of the added electrolyte ions. Therefore, AF4 proves to be sensitive to subtile changes of interaction forces on the level of Coulomb and van der Waals forces. The experimentally gathered elution times were used to develop a model describing the retention behavior, based on an enhanced version of the standard AF4 model: By introducing particle-medium-membrane interactions in the standard AF4 model via the respective Hamaker constants, the calculation of retention times was possible. The congruence of the calculated with the experimental retention times confirmed the validity of the simulation.

High-resolution compositional mapping of surfaces in non-contact atomic force microscopy by a new multi-frequency excitation.

In this paper, a new multi-frequency excitation method based on combination resonance is introduced to enhance the non-contact atomic force microscopy performance. In combination resonance, excitation frequencies are selected so that summation/subtraction of excitation frequencies is close to the natural frequencies of the microcantilever. Due to the nonlinear nature of this method, the probe response to excitation is very sensitive to change in tip-sample forces. This could be used to generate high-resolution compositional mapping and topographical images of the surface. The present study reveals that both amplitude and phase shift of the combination resonance are sensitive to change in parameters such as Hamaker constant, damping coefficient, Young's modulus and tip-sample initial distance. It is observed that because of high sensitivity to Hamaker constant a small change in the surface material leads to considerable variations in amplitude and phase shift. This sensitivity is employed to improve compositional mapping of the surface materials. It is also found out that the response amplitude in the combination resonance is very sensitive to change in the tip-sample initial distance. This sensitivity may be used to reduce the vertical noise and increase image resolution, especially in environments with low quality factors. Overall, using this technique the image contrast increases significantly and high resolution compositional mapping of surfaces is achieved.

Aggregation kinetics of UV-aged soot nanoparticles in wet environments: Effects of irradiation time and background solution chemistry.

Soot nanoparticles (SNPs) undergo aging processes in aqueous systems, altering their physicochemical properties and affecting their fate and transport. This study investigated the aging effects via ultraviolet irradiation on aggregation kinetics of SNPs in water. The results showed that, compared to fresh SNPs, those irradiated for 1 day aggregated more easily in NaCl and CaCl2 solutions, with reduction of critical coagulation concentrations by 72% and 40%, respectively. Similar phenomena were found in additional six electrolyte solutions, and SNPs irradiated for > 3 days had no measurable difference in aggregation rate. The aggregation-enhancement of irradiated SNPs was more prominent at low electrolyte concentrations and pH > 4. However, in the presence of macromolecules, irradiated SNPs could be stabilized against aggregation via steric hindrance with strength of bovine serum albumin > humic acid > alginate > fulvic acid, whereas alginate further destabilized aged SNPs via calcium bridging. The fitted Hamaker constant increased from 7.8 × 10-20 (fresh) to 1.2 × 10-19 J (7-day irradiated), suggesting that decarboxylation during irradiation may weaken electrical repulsion and enhance van der Waals attraction, promoting aggregation. These results demonstrated the vital role of UV-induced aging in fate and transport of SNPs in wet environments.

Lifshitz theory of wetting films at three phase coexistence: The case of ice nucleation on Silver Iodide (AgI).

HYPOTHESIS: As a fluid approaches three phase coexistence, adsorption may take place by the successive formation of two intervening wetting films. The equilibrium thickness of these wetting layers is the result of a delicate balance of intermolecular forces, as dictated by an underlying interface potential. The van der Waals forces for the two variable adsorption layers may be formulated exactly from Dzyaloshinskii-Lifshitz-Pitaevskii theory, and analytical approximations may be derived that extent well beyond the validity of conventional Hamaker theory. CALCULATIONS: We consider the adsorption equilibrium of water vapor on Silver Iodide where both ice and a water layers can form simultaneously and compete for the vapor as the triple point is approached. We perform numerical calculations of Lifshitz theory for this complex system and work out analytical approximations which provide quantitative agreement with the numerical results. FINDINGS: At the three phase contact line between AgI/water/air, surface forces promote growth of ice both on the AgI/air and the water/vapor interfaces, lending support to a contact nucleation mode of AgI in the atmosphere. Our approach provides a framework for the description of adsorption at three phase coexistence, and allows for the study of ice nucleation efficiency on atmospheric aerosols.

Modulation of substrate van der Waals forces using varying thicknesses of polymer overlayers.

Thin polymeric coatings are commonly used for altering surface properties and modulating the interfacial performance of materials. Possible contributions from the substrate to the interfacial forces and effects are, however, usually ignored and are not well understood, nor is it established how the coating thickness modulates and eventually eliminates contributions from substrates to the van der Waals (vdW) interfacial force. In this study we quantified, by colloid-probe atomic force microscope (AFM) and by theoretical calculations, the interfacial vdW contributions from substrates acting through ethanol plasma polymer (EtOHpp) coatings of a range of thicknesses on Au and Si bulk materials. In approach force curves against EtOHpp-coated Au substrates the magnitude of the vdW force decreased as the EtOHpp coating thickness increased to 18 nm and then plateaued with further increases in coating thickness, providing direct evidence for a contribution to the total interfacial vdW force from the Au substrate acting through thin coatings. The experimental observations accord with theoretical calculations of the thickness dependence of Hamaker coefficients derived from rigorous simulation using the Lifshitz theory. In addition, the measured forces agree well with theoretical predictions including correction for finite roughness. Thus, our experimental and theoretical results establish how the thickness of polymer thin film coatings modulates the total interfacial vdW force and how this can be used to tune the net vdW force so as to either contain a large substrate contribution or arise predominantly from the polymeric overlayer. Our findings enable rational design of coating thickness to tailor interfacial interactions and material performance.

Aggregation of oxidized multi-walled carbon nanotubes: Interplay of nanomaterial surface O-functional groups and solution chemistry factors.

The fast-growing production and application of carbon nanotube (CNT) materials in a variety of industrial products inevitably lead to their release to wastewater and surface water. CNT would experience oxidization in wastewater treatment plant due to the presence of large amount of disinfectants, such as H2O2 and O3, which in turn affects the environmental fates and risks of CNT. In this study, oxidized CNT materials (O-CNTs) were prepared by treating CNT with H2O2/UV and O3 (denoting as H2O2-CNT and O3-CNT, respectively). A variety of characterizations indicated that oxygen containing groups were generated on CNT surface upon the oxidation, and the O/C ratio increased in the order of pristine CNT < H2O2-CNT < O3-CNT. In the presence of Na+, K+ and Mg2+, the O-CNTs displayed better colloidal stability than the pristine CNT, and the stability increased with the oxidation degree (indicated by O/C ratio). This could be explained by the more negative surface charge and stronger hydrophilicity of the O-CNTs. Unexpectedly, in the presence of Ca2+, the most oxidized O3-CNT exhibited the poorest colloidal stability. The abundant carboxyl groups in O3-CNT provided effective binding sites for cation bridging effect through Ca2+ and led to stronger aggregation. Increasing pH was more favorable to disperse CNTs (both O-CNT and pristine CNT) in the presence of Na+, but much less effective in inhibiting the aggregation of O3-CNT in presence of Ca2+. This could be explained by the stronger cation bridging effect due to enhanced deprotonation the -COOH groups at higher pH conditions. The calculated Hamaker constants of the CNTs decreased with the oxidation degree, implying that there was lower van der Waals force between the O-CNTs. The Derjaguin-Landau-Verwey-Overbeek (DLVO) calculation confirmed that O-CNTs had to overcome higher energy barrier and thus showed better colloidal stability than the pristine CNT in the presence of Na+.

Aggregation kinetics of UV irradiated nanoplastics in aquatic environments.

Nanoplastics (NPs) derived from degradation of macroplastics and microplastics possess potential threat to aquatic biota and human health. Their fate and transport in aquatic systems are mainly governed by aging processes and aggregation behavior. In this study, we simulated plastic aging process using UV-irradiation and compared the aggregation kinetics of fresh versus aged polystyrene NPs (PSNPs) under aqueous conditions. The results showed that fresh PSNPs had strong negative surface charge and exhibited both reaction- and diffusion-limited aggregation regimes, in agreement with classic Derjaguin-Landau-Verwey-Overbeek (DLVO) theory. Divalent electrolytes were 10-15 times more effective in inducing PSNP aggregation than monovalent electrolytes. The aging process inhibited PSNP aggregation in NaCl solutions by increasing the negative charge on PSNP surface and the organic matter content in solution, while promoted PSNP aggregation in CaCl2 solutions due to interactions between Ca2+ and carboxyl groups formed on aged PSNP surface. Such distinct behaviors were consistent with characterizations by contact angle measurements, potentiometric titration, total organic carbon (TOC) analysis, Fourier Transform Infrared Spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). Hamaker constants obtained from DLVO fitting decreased from 3.5 × 10-21 J for fresh PSNPs to 1.5 × 10-21 J for aged PSNPs. This study indicated that UV-irradiation plays a vital role in governing the fate, transport, and potential hazards of PSNPs in aquatic environments.

Lifshitz analysis of dispersion forces based on quantitative reflection electron energy loss spectroscopy.

HYPOTHESIS: The energy loss experienced by an electron while moving through a solid is determined by the optical properties of the surrounding. Hence, quantitative Reflection Electron Energy Loss Spectroscopy (REELS) should allow the determination of optical data required for the calculation of Hamaker coefficients using Lifshitz theory. This approach might improve the accuracy of calculated Hamaker coefficients and should also enable to harness the unique capabilities of REELS to analyse nanostructured surfaces and thin-films with great spatial resolution and surface sensitivity. EXPERIMENTS: REELS spectra of a survey of insulating polymers and of metal-like Ti0.23Al0.32N0.44 (TiAlN) were measured, the complex dielectric functions determined and the corresponding Hamaker coefficients across vacuum and water calculated. The sensitivity of the quantification procedure towards typical systematic errors was investigated. For polystyrene the results were comparatively analysed using vacuum ultraviolet spectroscopy (VUV). FINDINGS: The accuracy especially of the non-retarded vacuum Hamaker constants of the polymers was increased when compared to VUV reflectance spectroscopy due to the higher spectral range of REELS. Furthermore, a new correction procedure for the intricate case of unresolved inelastic losses in the REELS spectrum, such as encountered in the case of TiAlN, could be developed using spectroscopic ellipsometry as a complementary mean.

Non-contact AFM measurement of the Hamaker constants of solids: Calibrating cantilever geometries.

HYPOTHESIS: Surface effects arising from roughness and deformation can negatively affect the results of AFM contact experiments. Using the non-contact portion of an AFM deflection curve is therefore desirable for estimating the Hamaker constant, A, of a solid material. A previously validated non-contact quasi-dynamic method for estimating A is revisited, in which the cantilever tip is now always represented by an "effective sphere". In addition to simplifying this previous method, accurate estimates of A can still be obtained even though precise knowledge of the nanoscale geometric features of the cantilever tip are no longer required. EXPERIMENTS: The tip's "effective" radius of curvature, Reff, is determined from a "calibration" step, in which the tip's deflection at first contact with the surface is measured for a substrate with a known Hamaker constant. After Reff is known for a given tip, estimates of A for other surfaces of interest are then determined. FINDINGS: An experimental study was conducted to validate the new method and the obtained results are in good agreement with predictions from the Lifshitz approximation, when available. Since Reff accounts for all geometric uncertainties of the tip through a single fitted parameter, no visual fitting of the tip shape was required.

In situ characterization of nanoscale contaminations adsorbed in air using atomic force microscopy.

Under ambient conditions, surfaces are rapidly modified and contaminated by absorbance of molecules and a variety of nanoparticles that drastically change their chemical and physical properties. The atomic force microscope tip-sample system can be considered a model system for investigating a variety of nanoscale phenomena. In the present work we use atomic force microscopy to directly image nanoscale contamination on surfaces, and to characterize this contamination by using multidimensional spectroscopy techniques. By acquisition of spectroscopy data as a function of tip-sample voltage and tip-sample distance, we are able to determine the contact potential, the Hamaker constant and the effective thickness of the dielectric layer within the tip-sample system. All these properties depend strongly on the contamination within the tip-sample system. We propose to access the state of contamination of real surfaces under ambient conditions using advanced atomic force microscopy techniques.

A review on data and predictions of water dielectric spectra for calculations of van der Waals surface forces.

Van der Waals forces are one of the important components of intermolecular, colloidal and surface forces governing many phenomena and processes. The latest examples include the colloidal interactions between hydrophobic colloids and interfaces in ambient (non-degassed) water in which dissolved gases and nanobubbles are shown to affect the van der Waals attractions significantly. The advanced computation of van der Waals forces in aqueous systems by the Lifshitz theory requires reliable data for water dielectric spectra. In this paper we review the available predictions of water dielectric spectra for calculating colloidal and surface van der Waals forces. Specifically, the available experimental data for the real and imaginary parts of the complex dielectric function of liquid water in the microwave, IR and UV regions and various corresponding predictions of the water spectra are critically reviewed. The data in the UV region are critical, but the available predictions are still based on the outdated data obtained in 1974 (for frequency only up to 25.5eV). We also reviewed and analysed the experimental data obtained for the UV region in 2000 (for frequency up to 50eV) and 2015 (for frequency up to 100eV). The 1974 and 2000 data require extrapolations to higher frequencies needed for calculating the van der Waals forces but remain inaccurate. Our analysis shows that the latest data of 2015 do not require the extrapolation and can be used to reliably calculate van der Waals forces. The most recent water dielectric spectra gives the (non-retarded) Hamaker constant, A=5.20×10-20J, for foam films of liquid water. This review provides the most updated and reliable water dielectric spectra to compute van der Waals forces in aqueous systems.

An evaluation of complementary approaches to elucidate fundamental interfacial phenomena driving adhesion of energetic materials.

Cohesive Hamaker constants of solid materials are measured via optical and dielectric properties (i.e., Lifshitz theory), inverse gas chromatography (IGC), and contact angle measurements. To date, however, a comparison across these measurement techniques for common energetic materials has not been reported. This has been due to the inability of the community to produce samples of energetic materials that are readily compatible with contact angle measurements. Here we overcome this limitation by using physical vapor deposition to produce thin films of five common energetic materials, and the contact angle measurement approach is applied to estimate the cohesive Hamaker constants and surface energy components of the materials. The cohesive Hamaker constants range from 85zJ to 135zJ across the different films. When these Hamaker constants are compared to prior work using Lifshitz theory and nonpolar probe IGC, the relative magnitudes can be ordered as follows: contact angle>Lifshitz>IGC. Furthermore, the dispersive surface energy components estimated here are in good agreement with those estimated by IGC. Due to these results, researchers and technologists will now have access to a comprehensive database of adhesion constants which describe the behavior of these energetic materials over a range of settings.

Stability of Polymer Ultrathin Films (<7 nm) Made by a Top-Down Approach.

In polymer physics, the dewetting of spin-coated polystyrene ultrathin films on silicon remains mysterious. By adopting a simple top-down method based on good solvent rinsing, we are able to prepare flat polystyrene films with a controlled thickness ranging from 1.3 to 7.0 nm. Their stability was scrutinized after a classical annealing procedure above the glass transition temperature. Films were found to be stable on oxide-free silicon irrespective of film thickness, while they were unstable (<2.9 nm) and metastable (>2.9 nm) on 2 nm oxide-covered silicon substrates. The Lifshitz-van der Waals intermolecular theory that predicts the domains of stability as a function of the film thickness and of the substrate nature is now fully reconciled with our experimental observations. We surmise that this reconciliation is due to the good solvent rinsing procedure that removes the residual stress and/or the density variation of the polystyrene films inhibiting thermodynamically the dewetting on oxide-free silicon.