Extremely Stable Ag-Based Photonics, Plasmonic, Optical, and Electronic Materials and Devices Designed with Surface Chemistry Engineering for Anti-Tarnish.

Silver (Ag) metal-based structures are promising building blocks for next-generation photonics and electronics owing to their unique characteristics, such as high reflectivity, surface plasmonic resonance effects, high electrical conductivity, and tunable electron transport mechanisms. However, Ag structures exhibit poor sustainability in terms of device performance because harsh chemicals, particularly S2- ions present in the air, can damage their structures, lowering their optical and electrical properties. Here, the surface chemistry of Ag structures with (3-mercaptopropyl)trimethoxysilane (MPTS) ligands at room temperature and under ambient conditions is engineered to prevent deterioration of their optical and electrical properties owing to S2- exposure. Regardless of the dimensions of the Ag structures, the MPTS ligands can be applied to each dimension (0D, 1D, and 3D). Consequently, highly sustainable plasmonic effects (Δλ < 2 nm), Fabry-Perot cavity resonance structures (Δλ < 2 nm), reflectors (ΔRReflectance < 0.5%), flexible electrodes (ΔRelectrical < 0.1 Ω), and strain gauge sensors (ΔGF < 1), even in S2- exposing conditions is achieved. This strategy is believed to significantly contribute to environmental pollution reduction by decreasing the volume of electronic waste.

Runtime ML-DL Hybrid Inference Platform Based on Multiplexing Adaptive Space-Time Resolution for Fast Car Incident Prevention in Low-Power Embedded Systems.

Forward vehicle detection is the key technique to preventing car incidents in front. Artificial intelligence (AI) techniques are used to more accurately detect vehicles, but AI-based vehicle detection takes a lot of processing time due to its high computational complexity. When there is a risk of collision with a vehicle in front, the slow detection speed of the vehicle may lead to an accident. To quickly detect a vehicle in real-time, a high-speed and lightweight vehicle detection technique with similar detection performance to that of an existing AI-based vehicle detection is required. In addition, to apply forward collision warning system (FCWS) technology to vehicles, it is important to provide high performance based on low-power embedded systems because the vehicle's battery consumption must remain low. The vehicle detection algorithm occupies the most resources in FCWS. To reduce power consumption, it is important to reduce the computational complexity of an algorithm, that is, the amount of resources required to run it. This paper describes a method for fast, accurate forward vehicle detection using machine learning and deep learning. To detect a vehicle in consecutive images consistently, a Kalman filter is used to predict the bounding box based on the tracking algorithm and correct it based on the detection algorithm. As a result, its vehicle detection speed is about 25.85 times faster than deep-learning-based object detection is, and its detection accuracy is better than machine-learning-based object detection is.

Effects and Mechanism of Surface Water Wettability and Operating Frequency on Response Linearity of Flexible IDE Capacitive Humidity Sensor.

Flexible capacitive humidity sensors are promising for low-cost, wearable, and radio frequency identification sensors, but their nonlinear response is an important issue for practical applications. Herein, the linearity of humidity response was controlled by surface water wettability and operating frequency of sensor, and the mechanism was explained in detail by surface water condensation. For a sensor with a Ag interdigitated electrode (IDE) on a poly(ethylene terephthalate) substrate, the capacitance showed a small linear increase with humidity up to 70% RH but a large nonlinear increase in the higher range. The response linearity was increased by a hydrophobic surface treatment of self-assembled monolayer coating while it was decreased by an ultraviolet/ozone irradiation for hydrophilicity. It was also increased by increasing the frequency in the range of 1-100 kHz, more prominently on a more hydrophilic surface. Based on experiment and simulation, the increase in sensor capacitance was greatly dependent on the geometric pattern (e.g., size, number, and contact angle) and electrical permittivity of surface water droplets. A larger and more nonlinear humidity response resulted from a larger increase in the number of droplets with a smaller contact angle on a sensor surface with higher water wettability and also from a higher permittivity of water at a lower frequency.

Automotive augmented reality 3D head-up display based on light-field rendering with eye-tracking.

We explore the feasibility of implementing stereoscopy-based 3D images with an eye-tracking-based light-field display and actual head-up display optics for automotive applications. We translate the driver's eye position into the virtual eyebox plane via a "light-weight" equation to replace the actual optics with an effective lens model, and we implement a light-field rendering algorithm using the model-processed eye-tracking data. Furthermore, our experimental results with a prototype closely match our ray-tracing simulations in terms of designed viewing conditions and low-crosstalk margin width. The prototype successfully delivers virtual images with a field of view of 10° × 5° and static crosstalk of <1.5%.

Solution-processable multi-color printing using UV nanoimprint lithography.

Recently, coloring based on nanostructure-light interaction has attracted much attention, because it has many advantages over pigment-based conventional coloring in terms of being non-toxic and highly durable in the environment, and providing high resolution. The asymmetric Fabry-Perot (FP) cavity absorber is the most manufacturable structure among coloring structures because it is simply produced and easily tunable. However, it cannot be applied practically because of the lack of a manufacturing technique that enables simultaneous fabrication of multi-color structures with different heights. Here, the fabrication of colored reflective characters based on various asymmetric FP absorbers with micrometer-scale pixel size are reported. Various cavities with different thicknesses are fabricated in a single step using UV imprint lithography and a simple deposition process. UV/visible spectroscopy is used to characterize the fabricated FP resonator. This absorber demonstrates high absorption, close to 90%, resulting in vivid colors with high resolution of 12700 DPI. It can be potentially used in reflective color displays field, functionalized color decorations, and security color patterns area. It is believed that this study would open up new possibilities for high density color printing in practical industry by introducing cost effective nanoimprint lithography technology.

Preparation of Mesoporous CuCe-Based Ternary Metal Oxide by Nano-Replication and Its Application to Decomposition of Liquid Monopropellant.

Mesoporous CuCe-based ternary metal oxides were synthesized using KIT-6 as a hard template through a nano-casting method. The mesoporous CuCe-based metal oxides were applied to the catalytic decomposition of the ammonium dinitramide-based liquid monopropellant. The decomposition onset temperature over the meso-CuCe ternary metal oxides was much lower than that over the CuCeOx catalyst prepared by conventional precipitation method. Higher activity of the meso-CuCe ternary metal oxides is attributed to higher surface area and larger pore size of the meso-CuCe ternary metal oxides than those of the conventional CuCe oxide. The highest activity of meso-CuCeZr catalyst among the meso-CuCe ternary metal oxide catalysts is likely due to the highest mesoporosity.

Ordered Mesoporous Cu-Mn Metal Oxides for the Catalytic Decomposition of an Energetic Ionic Liquid.

Ordered mesoporous Cu-Mn binary metal oxide (meso-CuMnOx) catalysts were successfully synthesized by a hard-templating method from a mesoporous silica template with a cubic Ia3d mesostructure (KIT-6) or hydrophobic KIT-6, exhibiting a well-developed crystalline framework, a regular pore size distribution and a high surface area. The copper and manganese elements in the mesoporous Cu-Mn binary metal oxides (meso-CuMnOx-N and meso-CuMnOx-HP), obtained from the KIT-6 and hydrophobic KIT-6, respectively, were homogeneously dispersed in the whole particles. The activities of meso-CuMnOx catalysts for the decomposition of a liquid monopropellant containing an energetic ionic liquid, ammonium dinitramide, were much higher than that over a CuMnOx catalyst prepared by a conventional precipitation method. This is attributed to the well-developed mesoporosity of the meso-CuMnOx catalysts. Among the mesoporous CuMnOx catalysts, the decomposition onset temperature over meso-CuMnOx-HP (87.9 °C) was found to be lower than that over meso-CuMnOx-N (100.4 °C), probably due to its higher mesoporosity and surface area.

Hierarchical Materials Design by Pattern Transfer Printing of Self-Assembled Binary Nanocrystal Superlattices.

We demonstrate the fabrication of hierarchical materials by controlling the structure of highly ordered binary nanocrystal superlattices (BNSLs) on multiple length scales. Combinations of magnetic, plasmonic, semiconducting, and insulating colloidal nanocrystal (NC) building blocks are self-assembled into BNSL membranes via the liquid-interfacial assembly technique. Free-standing BNSL membranes are transferred onto topographically structured poly(dimethylsiloxane) molds via the Langmuir-Schaefer technique and then deposited in patterns onto substrates via transfer printing. BNSLs with different structural motifs are successfully patterned into various meso- and microstructures such as lines, circles, and even three-dimensional grids across large-area substrates. A combination of electron microscopy and grazing incidence small-angle X-ray scattering (GISAXS) measurements confirm the ordering of NC building blocks in meso- and micropatterned BNSLs. This technique demonstrates structural diversity in the design of hierarchical materials by assembling BNSLs from NC building blocks of different composition and size by patterning BNSLs into various size and shape superstructures of interest for a broad range of applications.

Chemically tailored dielectric-to-metal transition for the design of metamaterials from nanoimprinted colloidal nanocrystals.

We demonstrate optical metamaterial design using colloidal gold nanocrystal building blocks. In the solid state, chemically exchanging the nanocrystals' surface-capping molecules provides a tailorable dielectric-to-metal transition exhibiting a 10(10) range in DC conductivity and dielectric permittivity ranging from everywhere positive to everywhere negative throughout the visible-to-near-IR. Direct, wide-area nanoimprinting of subwavelength superstructures at room temperature, on plastic and glass substrates, affords plasmonic resonances ranging from 660 to 1070 nm, in agreement with numerical simulations.

Near-infrared metatronic nanocircuits by design.

Lumped circuit elements (i.e., resistors, capacitors, and inductors) provide the basic building blocks of microelectronic devices ubiquitous in information processing, storage, and communications. The use of these modular quasistatic components can be extended to the nanoscale optical regime to achieve high-density, high-speed analogues of these traditional circuits. We reimagine these devices in the near-infrared (NIR) regime, making use of a simple nanorod geometry and plasmonic transparent conducting oxides (TCOs). We evaluate their equivalent impedance as lumped circuit elements and construct bandpass and band-stop filters operating at NIR wavelengths. Through variation in the TCO nanorod geometry and the addition of PbS nanocrystals in between and NiCr on top of the TCO nanorods, we present the first designable NIR lumped nanocircuits with tailorable response. The experimental results agree with both circuit models and full-wave simulations.

Fabrication of 3D nano-structures using reverse imprint lithography.

In spite of the fact that the fabrication process of three-dimensional nano-structures is complicated and expensive, it can be applied to a range of devices to increase their efficiency and sensitivity. Simple and inexpensive fabrication of three-dimensional nano-structures is necessary. In this study, reverse imprint lithography (RIL) with UV-curable benzylmethacrylate, methacryloxypropyl terminated poly-dimethylsiloxane (M-PDMS) resin and ZnO-nano-particle-dispersed resin was used to fabricate three-dimensional nano-structures.UV-curable resins were placed between a silicon stamp and a PVA transfer template, followed by a UV curing process. Then, the silicon stamp was detached and a 2D pattern layer was transferred to the substrate using diluted UV-curable glue. Consequently, three-dimensional nano-structures were formed by stacking the two-dimensional nano-patterned layers. RIL was applied to a light-emitting diode (LED) to evaluate the optical effects of a nano-patterned layer. As a result, the light extraction of the patterned LED was increased by about 12% compared to an unpatterned LED.

Polarization-driven thermal emission regulator based on self-aligned GST nanocolumns.

The increasing advances in thermal radiation regulators have attracted growing interest, particularly in infrared sources, thermal management, and camouflage. Despite many advances in dynamic thermal emitters with great controllability, sustained external energy is required to maintain the desired emission. In this study, we present a polarization-driven thermal emission regulator based on a two-way control: i) phase change and ii) polarization tuning. Based on a conventional, non-volatile phase change material, i.e., Ge2Sb2Te5 (GST), we newly introduce an anisotropic medium for facile emissivity regulation without heat energy consumption. A rigorous coupled-wave analysis method provides design guidelines for finding optimal structural parameters. We utilized a simple glancing angle deposition process which induces tilted self-aligned nanocolumns with anisotropic properties. The fabricated sample shows polarization-sensitive thermal regulation through thermal imaging spectroscopic measurement. Additionally, we manufactured a multispectral visibly/thermally camouflaged patch that identifies encrypted information at a specific polarization state for a proof-of-concept demonstration.

Radiofrequency catheter ablation of hemodynamically unstable ventricular tachycardia associated with systemic sclerosis.

Systemic sclerosis (SS) is a connective tissue disease and cardiac involvement is common. Primary cardiac involvement such as conduction system disturbances and arrhythmias can also occur. However, reports of sustained ventricular tachycardia (VT) are rare. We report a case of catheter ablation of sustained ventricular tachycardia in a patient with systemic sclerosis using a conventional mapping system. A 64-yr-old woman with a 10-yr history of SS was referred for management of her ventricular tachycardia. There was no structural abnormality in cardiac chambers. However, electrophysiologic study revealed electrical substrate of ventricular tachycardia which could be ablated with pacemapping and substrate mapping. This case demonstrated successful conventional mapping and catheter ablation in a hemodynamically unstable patient with SS.

Efficient use of immunosuppressants for kidney transplants.

A recent development of immunosuppressive protocols (or simply, suppressants) offers a new option to patients suffering from end-stage renal disease: transplants from biologically incompatible donors. Suppressants are currently being used for direct transplants within patient-donor pairs, but they can be utilized more efficiently when combined with kidney exchanges. To assess the welfare gains from doing so, we introduce the "minimum chains algorithms" for different sizes of feasible exchanges. Using these algorithms, we calculate the minimal number of suppressants needed for transplants for a group of patient-donor pairs. Our simulation results show that (i) a significant reduction of suppressants can be achieved by implementing this proposal, (ii) it suffices to arrange 2-way exchanges for the best use of suppressants, and (iii) the welfare gain varies with the ABO blood-type distribution, and the gain in Korea appears to be larger than that in the United States. Finally, we assess the value (or cost) of each patient-donor pair by comparing the outcomes of the pools with and without the pair.

Al2O3-Coated Si-Alloy Prepared by Atomic Layer Deposition as Anodes for Lithium-Ion Batteries.

Silicon-based anodes can increase the energy density of Li-ion batteries (LIBs) owing to their large weights and volumetric capacities. However, repeated charging and discharging can rapidly deteriorate the electrochemical properties because of a large volume change in the electrode. In this study, a commercial Fe-Si powder was coated with Al2O3 layers of different thicknesses via atomic layer deposition (ALD) to prevent the volume expansion of Si and suppress the formation of crack-induced solid electrolyte interfaces. The Al2O3 content was controlled by adjusting the trimethyl aluminum exposure time, and higher Al2O3 contents significantly improved the electrochemical properties. In 300 cycles, the capacity retention rate of a pouch full-cell containing the fabricated anodes increased from 69.8% to 72.3% and 79.1% depending on the Al2O3 content. The powder characterization and coin and pouch cell cycle evaluation results confirmed the formation of an Al2O3 layer on the powder surface. Furthermore, the expansion rate observed during the charging/discharging of the pouch cell indicated that the deposited layer suppressed the powder expansion and improved the cell stability. Thus, the performance of an LIB containing Si-alloy anodes can be improved by coating an ALD-synthesized protective Al2O3 layer.

Disordered-nanoparticle-based etalon for ultrafast humidity-responsive colorimetric sensors and anti-counterfeiting displays.

The development of real-time and sensitive humidity sensors is in great demand from smart home automation and modern public health. We hereby proposed an ultrafast and full-color colorimetric humidity sensor that consists of chitosan hydrogel sandwiched by a disordered metal nanoparticle layer and reflecting substrate. This hydrogel-based resonator changes its resonant frequency to external humidity conditions because the chitosan hydrogels are swollen under wet state and contracted under dry state. The response time of the sensor is ~104 faster than that of the conventional Fabry-Pérot design. The origins of fast gas permeation are membrane pores created by gaps between the metal nanoparticles. Such instantaneous and tunable response of a new hydrogel resonator is then exploited for colorimetric sensors, anti-counterfeiting applications, and high-resolution displays.

Multilevel Absorbers via the Integration of Undoped and Tungsten-Doped Multilayered Vanadium Dioxide Thin Films.

Reconfigurable light absorbers have attracted much attention by providing additional optical responses and expanding the number of degrees of freedom in security applications. Fabry-Pèrot absorbers based on phase change materials with tunable properties can be implemented over large scales without the need for additional steps such as lithography, while exhibiting reconfigurable optical responses. However, a fundamental limitation of widely used phase change materials such as vanadium dioxide and germanium-antimony-tellurium-based chalcogenide glasses is that they have only two distinct phases; therefore, only two different states of optical properties are available. Here, we experimentally demonstrate active multilevel absorbers that are tuned by controlling the external temperature. This is produced by creating large-scale lithography-free multilayer structures with both undoped and tungsten-doped solution-processed monoclinic-phase vanadium dioxide thin films. The doping of vanadium dioxide with tungsten allows for the modulation of the phase-transition temperature, which results in an extra degree of freedom and therefore an additional step for the tunable properties. The proposed multilevel absorber is designed and characterized both numerically and experimentally. Such large-scale multilevel tunable absorbers realized with nanoparticle-based solution fabrication techniques are expected to open the way for advanced thermo-optical cryptographic devices based on tunable reflective coloration and near-infrared absorption.

Actuating compact wearable augmented reality devices by multifunctional artificial muscle.

An artificial muscle actuator resolves practical engineering problems in compact wearable devices, which are limited to conventional actuators such as electromagnetic actuators. Abstracting the fundamental advantages of an artificial muscle actuator provides a small-scale, high-power actuating system with a sensing capability for developing varifocal augmented reality glasses and naturally fit haptic gloves. Here, we design a shape memory alloy-based lightweight and high-power artificial muscle actuator, the so-called compliant amplified shape memory alloy actuator. Despite its light weight (0.22 g), the actuator has a high power density of 1.7 kW/kg, an actuation strain of 300% under 80 g of external payload. We show how the actuator enables image depth control and an immersive tactile response in the form of augmented reality glasses and two-way communication haptic gloves whose thin form factor and high power density can hardly be achieved by conventional actuators.

Sorting Gold and Sand (Silica) Using Atomic Force Microscope-Based Dielectrophoresis.

Additive manufacturing-also known as 3D printing-has attracted much attention in recent years as a powerful method for the simple and versatile fabrication of complicated three-dimensional structures. However, the current technology still exhibits a limitation in realizing the selective deposition and sorting of various materials contained in the same reservoir, which can contribute significantly to additive printing or manufacturing by enabling simultaneous sorting and deposition of different substances through a single nozzle. Here, we propose a dielectrophoresis (DEP)-based material-selective deposition and sorting technique using a pipette-based quartz tuning fork (QTF)-atomic force microscope (AFM) platform DEPQA and demonstrate multi-material sorting through a single nozzle in ambient conditions. We used Au and silica nanoparticles for sorting and obtained 95% accuracy for spatial separation, which confirmed the surface-enhanced Raman spectroscopy (SERS). To validate the scheme, we also performed a simulation for the system and found qualitative agreement with the experimental results. The method that combines DEP, pipette-based AFM, and SERS may widely expand the unique capabilities of 3D printing and nano-micro patterning for multi-material patterning, materials sorting, and diverse advanced applications.

Fast switching behavior of nanoscale Ag6In5Sb59Te30 based nanopillar type phase change memory.

Ag and In co-doped SbTe phase change material (AgInSbTe) was used to fabricate nanopillar phase change memory. The AgInSbTe nanopillar type phase change device with 200 nm of diameter was fabricated by nanoimprint lithography and was reversibly changed between the resistances of 10(4) and 10(6) Omega by applying set/reset pulses using conducting atomic force microscopy. Due to the fast crystallization nature of AgInSbTe, the set operation of the device could be done with only 50 ns of set pulse. The fast crystallization nature of AgInSbTe is also responsible for the decrease in reset voltage of devices set with a short pulse.