Effectiveness of an actuator-driven pulsed water jet for removal of softened carious dentin.

The aim of this study was to assess the utility of an actuator-driven pulsed water jet (ADPJ) as a hardness-dependent carious dentin removal device by using different outputs. Thirty-six plane surface dental caries samples were treated with the ADPJ at 150, 200, and 250 voltage (12 teeth each). The Knoop hardness number (KHN) and Ca/P mass ratio were measured at 70 µm from the deepest point of the removing groove. Furthermore, three other teeth samples were manually treated with the ADPJ at the three above mentioned voltages (one tooth each) for 1 min. The KHN and Ca/P mass ratio were measured at 70 µm from the surface of the residual dentin part. In both the KHN and Ca/P mass ratio, higher residual dentin depended on the applied voltage of ADPJ. The ADPJ enabled the removal of softened carious dentin in an applied voltage-dependent manner.

Detection of Inflammatory and Homeostasis Biomarkers after Selective Removal of Carious Dentin-An In Vivo Feasibility Study.

Deep carious dentin lesions induce an immune reaction within the pulp-dentin complex, leading to the release of cytokines, which might be suitable biomarkers in pulp diagnostics. This in vivo feasibility study determines the concentration of different cytokines after selective removal of carious infected dentin (SCR). In our methodology, paired samples are obtained from 21 patients-each of them with two deep carious lesions at posterior teeth without clinical symptoms. After SCR, lesions are randomly assigned to treatment strategy: Group 1 (11 patients): Carious dentin is covered either with BiodentineTM (n = 11) or gutta-percha (n = 11) before using the adhesive OptibondTM FL. Group 2 (10 patients): The adhesives ClearfilTM SE Protect Bond (n = 10) or ClearfilTM SE Bond 2 (n = 10) are directly applied. Prepared cavities are rinsed with phosphate buffered saline containing 0.05% Tween 20 (10X) for five minutes immediately after SCR (visit 1) and eight weeks later (visit 2). Rinsing liquid is regained. Concentrations of IL-1ß, IL-6, IL-10, C-reactive protein (CRP), TNF-α, IFN-γ, TIMP-1, -2, and MMP-7, -8, -9 are assessed by customized multiplex assays, evaluated with fluorescence analyzer. Non-parametric statistical analysis (Wilcoxon, Mann-Whitney U Test, p < 0.05) is performed (SPSS 25). Our results show that concentrations of CRP, IL-1ß, IL-6, TIMP-1, -2, and MMPs were detectable. Median concentrations of CRP, IL-1ß und IL-6 were significantly higher in visit 1 (304.9, 107.4, 3.8 pg/mL), compared to visit 2 (67.8, 2.3, 0.0 pg/mL; pi < 0.001). The study revealed that the non-invasive determination of cytokines from prepared dental cavities is possible.

Antibacterial effect of a brominated self-etch adhesive on carious dentin - An in vivo study.

OBJECTIVES: This in vivo study compared the antibacterial effect of a self-etch adhesive with and without the brominated monomer 12-methacryloyloxydodecyl-pyridinium bromide (MDPB) on carious dentin after selective caries removal. METHODS: 10 patients showing deep primary carious lesions at two posterior teeth without pulpal symptoms were included. At visit I, carious tissue was selectively removed and carious dentin was sampled with a sterile roundbur (Komet No. 18). One cavity was restored with composite (SDR, Ceram X; DENTSPLY DeTrey) using an MDPB-containing self-etch adhesive (Clearfil Protect Bond, Kuraray Noritake; PB). The other restoration served as a control (Clearfil SE Bond II, Kuraray Noritake; SE). At visit II after 8 weeks, carious dentin was sampled again. Bacterial growth in carious dentin was differentiated using microbial cultivation. Bacterial DNA from intact cells and cell-free DNA were quantified using 16S rRNA gene-based real-time PCR and the microbial community composition was analyzed by amplicon deep-sequencing. Wilcoxon test was applied for statistical analysis. RESULTS: Both treatments showed a decrease of intact bacterial cells in carious dentin at visit II compared to visit I (PB: visit I: 1.1*106, visit II: 1.7*105 (p = 0.03); SE: visit I: 1.1*107, visit II = 2.4*105 (p = 0.002)). No statistically significant reduction of cell-free bacterial DNA was detected (PB: visit I: 6.1*105, visit II: 1.6*105 (p = 0.08); SE: visit I: 5.3*105, visit II: 2.9*105 (p = 0.10)). The decrease of intact cell-derived (p = 0.371) and cell-free DNA (p = 0.455) did not differ significantly between PB and SE. Lactobacillus was most abundant within the microbial community at both visits. Alpha-diversity was not affected by treatment and samples showed high intra- and interindividual diversity. CONCLUSION AND CLINICAL SIGNIFICANCE: Both self-etch adhesives have an antibacterial effect due to a decrease of bacterial DNA after selective caries removal. However, the results do not reveal any additional antibacterial effect by MDPB. The study is registered with the German Clinical Trials Register (DRKS00011532).

Treatment of caries affected dentin with different photosensitizers and its effect on adhesive bond integrity to resin composite.

OBJECTIVE: The aim of the present study was to evaluate the effect of different photosensitizers activated by photodynamic therapy (PDT) on shear bond strength (SBS) of composite resin on caries affected dentin compared to conventional cavity disinfectants. MATERIALS AND METHODS: Forty carious mandibular teeth were collected through non-traumatic extraction. All samples were embedded in polyvinyl cross-sections to the cemento-enamel junction. The preparation of caries-affected dentin was performed by grinding the specimens using silicon carbide discs. All specimens were arbitrarily allocated in to four groups (n = 10). Group 1, affected dentin disinfected with methylene blue (MB) [100 mg/L]; Group 2, caries affected dentin disinfected using curcumin photosensitizer (CP) [500 mg/L]; Group 3, affected dentin disinfected with indocyanin green photosensitizer (ICGP) [0.5 mL] Group 4, affected dentin treated with 3 % H2O2. Two-step self-etch adhesives was smeared on all specimens for 15 s and photopolymerized for 10 s. All specimens were placed in an incubator with humid environment for 24 h at 37 °C followed by positioning in universal testing machine for SBS testing. Failure mode examination of debonded samples was performed by a stereomicroscope. Analysis of variance (ANOVA) was used for inter group comparison through mean and standard deviation of each group. For multiple group comparison Tukey HSD was employed. Level of significance was established at p < 0.05. RESULT: In group 2 dentin disinfection using CP, displayed the highest SBS value (18.21 ± 1.39 MPa). Whereas, group 4 (3% H2O2 as cavity disinfectant) presented the lowest SBS values (13.39 ± 1.26 MPa). SBS in Group 3 (ICGP) (17.42 ± 0.55 MPa) specimens was comparable to group 2 (p > 0.05) samples. In group 1, samples disinfected with MB (15.18 ± 0.39 MPa) was found to be significantly lower compared to group 2 and group 3 (p < 0.05) respectively. CONCLUSION: Curcumin and Indocyanin green (ICGP) PS have the potential to be used as cavity disinfectant as it improves SBS of caries affected dentin to resin composite. Photodynamic therapy for disinfection of caries affected dentin will augment its bond strength, however its long-term effect on bond integrity still needs to be investigated.

Effect of a bioactive cement on the microbial community in carious dentin after selective caries removal - An in-vivo study.

OBJECTIVES: Selective caries removal in deep lesions means that soft carious affected dentin is left in the center of the cavity. Thus, using a tricalcium silicate cement Biodentine™ (Septodont, Paris) to seal the remaining soft dentin could have an antibacterial effect. This in-vivo study aimed to do quantitative and qualitative analyses on the bacterial composition within carious dentin before and after selective caries removal when applying Biodentine. METHODS: Eleven patients with deep primary carious lesions at two posterior teeth without pulpal symptoms were included. Carious dentin was selectively removed and sampled with a sterile round bur (Komet No. 18) at baseline visit and eight weeks later. On the first visit, one lesion per patient, the remaining carious dentin was covered with Biodentine before adhesive restoration. Caries samples were investigated by microbial cultivation, molecular analysis and amplicon deep-sequencing of 16S rRNA genes. Bacterial DNA from intact cells was differentiated from cell-free DNA by DNase degradation prior to DNA isolation. RESULTS: Reduction of cell-derived as well as cell-free bacterial DNA eight weeks after selective caries removal was significantly higher when Biodentine was applied. Lactobacillus was most abundant within the microbial community of deep carious dentin lesions at the first visit. After intervention with Biodentine application, Lactobacillus was diminished to a high degree. In general, the diversity in samples, as well as bacterial composition differed interindividually as well as intraindividually. CONCLUSION AND CLINICAL SIGNIFICANCE: Despite the heterogenous and diversity of microbial composition in patients, Biodentine can have beneficial antibacterial effects when applied to residual carious dentin, offering an alternative and safe treatment option. The study is officially registered with German Clinical Trials Register (DRKS00011067).

Performance of Adhesives and Restorative Materials After Selective Removal of Carious Lesions: Restorative Materials with Anticaries Properties.

Selective carious tissue-removal strategies require specific considerations in selection of restorative materials. A tight marginal seal placed over hard dentin and sound enamel is essential. For selective removal of carious tissue with permanent restoration, bioactive materials, such as high-viscosity glass-ionomer cement (HV-GIC) or calcium silicates, may be preferred over caries-affected firm or leathery dentin to improve remineralization. HV-GICs have the best clinical evidence of caries-arresting effect and demonstrate sufficient longevity as long-term provisional restorations that can later be used in open or closed sandwich restorations. As with any material, oral health maintenance remains important for long-term survival of restorations.

Comparative Physicochemical Analysis of Pulp Stone and Dentin.

INTRODUCTION: Odontoblasts are responsible for the synthesis of dentin throughout the life of the tooth. Tooth pulp tissue may undergo a pathologic process of mineralization, resulting in formation of pulp stones. Although the prevalence of pulp stones in dental caries is significant, their development and histopathology are poorly understood, and their precise composition has never been established. The aim of the present study was to investigate the physicochemical properties of the mineralized tissues of teeth to elucidate the pathologic origin of pulp stones. METHODS: Areas of carious and healthy dentin of 8 decayed teeth intended for extraction were analyzed and compared. In addition, 6 pulp stones were recovered from 5 teeth requiring root canal treatment. The samples were embedded in resin, sectioned, and observed by scanning electron microscopy and energy-dispersive spectroscopy. X-ray diffraction was performed to identify phases and crystallinity. X-ray fluorescence provided information on the elemental composition of the samples. RESULTS: Pulp stones showed heterogeneous structure and chemical composition. X-ray diffraction revealed partially carbonated apatite. X-ray fluorescence identified P, Ca, Cu, Zn, and Sr within dentin and pulp stones. Zn and Cu concentrations were higher in pulp stones and carious dentin compared with healthy dentin. CONCLUSIONS: Pulpal cells produce unstructured apatitic mineralizations containing abnormally high Zn and Cu levels.

Comparative efficacy of photo-activated disinfection and calcium hydroxide for disinfection of remaining carious dentin in deep cavities: a clinical study.

OBJECTIVES: To comparatively evaluate the efficacy of photo-activated disinfection (PAD), calcium hydroxide (CH) and their combination on the treatment outcome of indirect pulp treatment (IPT). MATERIALS AND METHODS: Institutional ethical clearance and informed consent of the patients were taken. The study was also registered with clinical registry of India. Sixty permanent molars exhibiting deep occlusal carious lesion in patients with the age range of 18 - 22 yr were included. Clinical and radiographic evaluation and set inclusion and exclusion criteria's were followed. Gross caries excavation was accomplished. In group I (n = 20) PAD was applied for sixty seconds. In group II (n = 20), CH was applied to the remaining carious dentin, while in group III (n = 20), PAD application was followed by CH placement. The teeth were permanently restored. They were clinically and radiographically followed-up at 45 day, 6 mon and 12 mon. Relative density of the remaining affected dentin was measured by 'Radiovisiography (RVG) densitometric' analysis. RESULTS: Successful outcome with an increase in radiographic grey values were observed in all three groups. However, on inter-group comparison, this change was not significant (p > 0.05). CONCLUSIONS: PAD and CH both have equal disinfection efficacy in the treatment of deep carious dentin. PAD alone is as effective for treatment of deep carious lesion as calcium hydroxide and hence can be used as an alternative to CH. They can be used independently in IPT, since combining both does not offer any additional therapeutic benefits.

Radiopaque Tagging Masks Caries Lesions following Incomplete Excavation in vitro.

One-step incomplete excavation seals caries-affected dentin under a restoration and appears to be advantageous in the treatment of deep lesions. However, it is impossible to discriminate radiographically between intentionally left, arrested lesions and overlooked or active lesions. This diagnostic uncertainty decreases the acceptance of minimally invasive excavation and might lead to unnecessary re-treatment of incompletely excavated teeth. Radiopaque tagging of sealed lesions might mask arrested lesions and assist in discrimination from progressing lesions. Therefore, we microradiographically screened 4 substances (SnCl2, AgNO3, CsF, CsCH3COO) for their effect on artificial lesions. Since water-dissolved tin chloride (SnCl2×Aq) was found to stably mask artificial lesions, we then investigated its radiographic effects on progressing lesions. Natural lesions were incompletely excavated and radiopaque tagging performed. Grey-value differences (△GV) between sound and carious dentin were determined and radiographs assessed by 20 dentists. While radiographic effects of SnCl2×Aq were stable for non-progressing lesions, they significantly decreased during a second demineralization (p < .001, t test). For natural lesions, tagging with SnCl2×Aq significantly reduced △GV (p < .001, Wilcoxon). Tagged lesions were detected significantly less often than untagged lesions (p < .001). SnCl2×Aq was suitable to mask caries-affected dentin and discriminate between arrested and progressing lesions in vitro. Radiopaque tagging could resolve diagnostic uncertainties associated with incomplete excavation.

Evaluation of the shear bond strength of nanocomposite on carious and sound deciduous dentin.

AIM: The aim of the study was to evaluate and compare the shear bond strength of conventional composites with nanocomposites in carious and sound deciduous dentin with the use of self-etching adhesive. METHODOLOGY: Human primary molars were ground to obtain flat dentin surfaces and divided into two groups: Carious dentin and sound dentin group. The carious teeth specimens were prepared by removing infected dentin and area with affected dentin was used for bonding composite. Teeth with carious and sound dentin were subdivided in two groups (n = 15) based on the type of the composite into conventional composite group and nanocomposite group. The composite was bonded to the teeth with self-etching adhesive. All the bonded specimens were stored in distilled water for 24 hours at 37°C before shear bond testing. Independent t-test and analysis of variance were applied to the results. RESULTS: The results indicated that the nanocomposite offered significantly higher bond strength compared to conventional composite. In addition presence of affected dentin significantly reduced the bond strength of both the composite types. How to cite this article: Deshmukh S, Nandlal B. Evaluation of the Shear Bond Strength of Nanocomposite on Carious and Sound Deciduous Dentin. Int J Clin Pediatr Dent 2012;5(1): 25-28.

Performance of laser fluorescence for residual caries detection in primary teeth.

OBJECTIVES: The aim of this study was to evaluate the performance of a visual-tactile examination and a laser fluorescence device for detecting residual dentinal caries after carious dentin removal with bur excavation, hand excavation and chemomechanical excavation (Carisolv()]. METHODS: Thirty extracted coronal caries primary second molars were used. The caries infected dentin has been removed. A blinded examiner checked all cavities for residual caries using a visual-tactile examination and laser fluorescence. Then the teeth were sectioned through the prepared cavities and the two halves of each tooth were processed for light microscopy and Scanning Electron Microscopy (SEM). The presence or absence of residual caries was verified using polarized light microscopy as the gold standard. The cavity floor dentin after removing carious dentin was examined using SEM. RESULTS: In among all groups a significant difference is determined between visual-tactile examination and laser fluorescence (P<.05). There was an agreement between laser fluorescence or visual-tactile examination and histological gold standard (P>.05). In addition, SEM images of the surfaces with the caries removed have shown that a vast majority of the tubule openings is observed to be open in the samples of the Carisolv group in opposition to the other groups. CONCLUSIONS: The laser fluorescence system could be effective in checking the removal by other methods, such as bur or Carisolv and avoid excessive removal of the sound dentin.