Stable and Reusable Fe3 O4 /ZIF-8 Composite for Encapsulation of FDH Enzyme under Mild Conditions Applicable to CO2 Reduction.

The enzymatic reduction of carbon dioxide presents limited applicability due to denaturation and the impossibility of biocatalyst recovery; disadvantages that can be minimized by its immobilization. Here, a recyclable bio-composed system was constructed by in-situ encapsulation under mild conditions using formate dehydrogenase in a ZIF-8 metalorganic framework (MOF) in the presence of magnetite. The partial dissolution of ZIF-8 in the enzyme's operation medium can be relatively inhibited if the concentration of magnetic support used exceeds 10 mg mL-1 . The bio-friendly environment for immobilization does not harm the integrity of the biocatalyst, and the production of formic acid is improved 3.4-fold compared to the free enzyme because the MOFs act as concentrators of the enzymatic cofactor. Furthermore, the bio-composed system retains 86 % of its activity after a long time of five cycles, thus indicating an excellent magnetic recovery and a good reusability.

Direct Polyethylene Photoreforming into Exclusive Liquid Fuel over Charge-Asymmetrical Dual Sites under Mild Conditions.

Direct polyethylene photoreforming to high-energy-density C2 fuels under mild conditions is of great significance and still faces a huge challenge, which is partly attributed to the extreme instability of *CH2CH2 adsorbed on the traditional catalysts with single catalytic sites. Herein, charge-asymmetrical dual sites are designed to boost the adsorption of *CH2CH2 for direct polyethylene photoreforming into C2 fuels under normal temperature and pressure. As a prototype, the synthetic Zr-doped CoFe2O4 quantum dots with charge-asymmetrical dual metal sites realize direct polyethylene photoreforming into acetic acid, with 100% selectivity of liquid fuel and the evolution rate of 1.10 mmol g-1 h-1, outperforming those of most previously reported photocatalysts under similar conditions. In situ X-ray photoelectron spectra, density-functional-theory calculations, and control experiments reveal the charge-asymmetrical Zr-Fe dual sites may act as the predominate catalytic sites, which can simultaneously bond with the *CH2CH2 intermediates for the following stepwise oxidation to form C2 products.

A Visible Light-Induced and ROS-Dependent Method for the Rapid Formation of a MOF Composite Membrane with Antibacterial Properties.

The diverse application potential of metal-organic framework (MOF) materials are currently limited by their challenging and complicated preparation processes. In this study, we successfully developed a novel strategy for the rapid synthesis of a sustainable MOF composite membrane under neutral conditions with improved physicochemical and antibacterial properties. Our reaction pipeline comprised visible light that induced the production of reactive oxygen species (ROS) from ZIF-8 particles, which facilitated the rapid oxidative polymerization of dopamine to polydopamine. The physicochemical properties of the composite membrane were assessed using imaging methods, including scanning and transmission electron microscopy, X-ray photoelectron spectrometry, and nitrogen adsorption/desorption; its antibacterial effects against Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa were measured using optical densitometry. The bactericidal potency of the synthesized membrane was >99% against all tested strains under the conditions of simulated sunlight. Moreover, the composite membrane retained its structural integrity and antibacterial effect after multiple cycles of use and recovery, showcasing remarkable stability. Overall, this study displays a ROS-mediated method for the rapid preparation of sustainable MOF composite membranes under neutral conditions with optimal physicochemical characteristics, antibacterial properties, and performance. Our study provides insights into the use of membrane materials as design platforms for a range of diverse practical applications.

A novel combined metallurgy-beneficiation method for the facile and low-cost comprehensive resource utilization of low-grade kaolin solid wastes.

Low-grade kaolin is the largest emissions of industrial solid waste that is difficult to dispose of and pollutes the environment seriously. From the perspective of harmless and complete resource utilization, we proposed a novel strategy that combines the wet leaching under mild conditions and physical beneficiation for the facile and low-cost high-valued utilization of low-grade kaolin that involves high-efficiency recovery of aluminum (Al), silicon (Si), and titanium (Ti). The key to successful implementation of this method lies in the new discovery that the residual SiO2 after Al extraction of kaolinite by acid leaching under specific conditions could be rapidly dissolved in dilute NaOH solution at room temperature 25 °C. This highly reactive SiO2 challenges the conventional notions of various silica species are usually chemically stable. By adjusting the key technical parameters of the thermal activation-acid leaching process, the selective and efficient extraction of Al2O3 from low-grade kaolin was realized. The acid leaching residue was then subjected to selective recovery of SiO2 by alkaline leaching at 25 °C to obtain high-quality sodium silicate. Finally, the alkali leaching residue as titanium coarse concentrate was separated by centrifugal concentrator to obtain artificial rutile (TiO2 >91.06%). The key mechanism for the formation of the highly reactive silica was also systematically studied and confirmed.

Electrocatalytic Water Splitting: From Harsh and Mild Conditions to Natural Seawater.

Electrocatalytic water splitting is regarded as the most effective pathway to generate green energy-hydrogen-which is considered as one of the most promising clean energy solutions to the world's energy crisis and climate change mitigation. Although electrocatalytic water splitting has been proposed for decades, large-scale industrial hydrogen production is hindered by high electricity cost, capital investment, and electrolysis media. Harsh conditions (strong acid/alkaline) are widely used in electrocatalytic mechanism studies, and excellent catalytic activities and efficiencies have been achieved. However, the practical application of electrocatalytic water splitting in harsh conditions encounters several obstacles, such as corrosion issues, catalyst stability, and membrane technical difficulties. Thus, the research on water splitting in mild conditions (neutral/near neutral), even in natural seawater, has aroused increasing attention. However, the mechanism in mild conditions or natural seawater is not clear. Herein, different conditions in electrocatalytic water splitting are reviewed and the effects and proposed mechanisms in the three conditions are summarized. Then, a comparison of the reaction process and the effects of the ions in different electrolytes are presented. Finally, the challenges and opportunities associated with direct electrocatalytic natural seawater splitting and the perspective are presented to promote the progress of hydrogen production by water splitting.

Selective CH4 Partial Photooxidation by Positively Charged Metal Clusters Anchored on Carbon Aerogel under Mild Conditions.

Selective partial photooxidation of CH4 into value-added chemicals under mild conditions still remains a huge bottleneck. Herein, we design positively charged metal clusters anchored on a three-dimensional porous carbon aerogel. With 0.75FeCA800-4 as an example, X-ray photoelectron spectra and Raman spectra disclose that the iron sites are positively charged. In situ electron paramagnetic resonance spectra show that the Feδ+ sites could donate electrons to activate CH4 into CH4- by virtue of the excited-state carbon atoms; meanwhile, they could convert H2O2 into •OH radicals under irradiation. In addition, in situ diffuse Fourier-transform infrared spectra suggest the CH3OOH obtained is derived from CH4 oxidation by the hydroxylation of *CH3 and *CH3O intermediates. Consequently, 0.75FeCA800-4 displays a CH3OOH selectivity of near 100% and a CH3OOH evolution rate of 13.2 mmol gFe-1 h-1, higher than those of most previously reported supported catalysts under similar conditions.

Efficient Oxidation of Cyclohexane over Bulk Nickel Oxide under Mild Conditions.

Nickel oxide powder was prepared by simple calcination of nickel nitrate hexahydrate at 500 °C for 5 h and used as a catalyst for the oxidation of cyclohexane to produce the cyclohexanone and cyclohexanol-KA oil. Molecular oxygen (O2), hydrogen peroxide (H2O2), t-butyl hydrogen peroxide (TBHP) and meta-chloroperoxybenzoic acid (m-CPBA) were evaluated as oxidizing agents under different conditions. m-CPBA exhibited higher catalytic activity compared to other oxidants. Using 1.5 equivalent of m-CPBA as an oxygen donor agent for 24 h at 70 °C, in acetonitrile as a solvent, NiO powder showed exceptional catalytic activity for the oxidation of cyclohexane to produce KA oil. Compared to different catalytic systems reported in the literature, for the first time, about 85% of cyclohexane was converted to products, with 99% KA oil selectivity, including around 87% and 13% selectivity toward cyclohexanone and cyclohexanol, respectively. The reusability of NiO catalyst was also investigated. During four successive cycles, the conversion of cyclohexane and the selectivity toward cyclohexanone were decreased progressively to 63% and 60%, respectively, while the selectivity toward cyclohexanol was increased gradually to 40%.

Synthesis of 5-unsubstituted dihydropyrimidinone-4-carboxylates from deep eutectic mixtures.

A facile one-pot synthesis of 5-unsubstituted dihydropyrimidinones from ß,γ-unsaturated ketoesters in low melting ʟ-(+)-tartaric acid-N,N-dimethylurea mixtures is reported. This solvent-free method is very general and provides easy access to 5-unsubstituted dihydropyrimidinone-4-carboxylate derivatives in good yields.

Highly Efficient and Rapid Inactivation of Coronavirus on Non-Metal Hydrophobic Laser-Induced Graphene in Mild Conditions.

The prevalence of COVID-19 has caused global dysfunction in terms of public health, sustainability, and socio-economy. While vaccination shows potential in containing the spread, the development of surfaces that effectively reduces virus transmission and infectivity is also imperative, especially amid the early stage of the pandemic. However, most virucidal surfaces are operated under harsh conditions, making them impractical or potentially unsafe for long-term use. Here, it is reported that laser-induced graphene (LIG) without any metal additives shows marvelous antiviral capacities for coronavirus. Under low solar irradiation, the virucidal efficacy of the hydrophobic LIG (HLIG) against HCoV-OC43 and HCoV-229E can achieve 97.5% and 95%, respectively. The photothermal effect and the hydrophobicity of the HLIG synergistically contribute to the superior inactivation capacity. The stable antiviral performance of HLIG enables its multiple uses, showing advantages in energy saving and environmental protection. This work discloses a potential method for antiviral applications and has implications for the future development of antiviral materials.

The Maillard Reaction as Source of Meat Flavor Compounds in Dry Cured Meat Model Systems under Mild Temperature Conditions.

Flavor is amongst the major personal satisfaction indicators for meat products. The aroma of dry cured meat products is generated under specific conditions such as long ripening periods and mild temperatures. In these conditions, the contribution of Maillard reactions to the generation of the dry cured flavor is unknown. The main purpose of this study was to examine mild curing conditions such as temperature, pH and aw for the generation of volatile compounds responsible for the cured meat aroma in model systems simulating dry fermented sausages. The different conditions were tested in model systems resembling dry fermented sausages at different stages of production. Three conditions of model system, labeled initial (I), 1st drying (1D) and 2nd drying (2D) and containing different concentrations of amino acid and curing additives, as well as different pH and aw values, were incubated at different temperatures. Changes in the profile of the volatile compounds were investigated by solid phase microextraction and gas chromatography mass spectrometry (SPME-GS-MS) as well as the amino acid content. Seventeen volatile compounds were identified and quantified in the model systems. A significant production of branched chain volatile compounds, sulfur, furans, pyrazines and heterocyclic volatile compounds were detected in the model systems. At the drying stages, temperature was the main factor affecting volatile production, followed by amino acid concentration and aw. This research demonstrates that at the mild curing conditions used to produce dry cured meat product volatile compounds are generated via the Maillard reaction from free amino acids. Moreover, in these conditions aw plays an important role promoting formation of flavor compounds.

A highly selective and sensitive boronic acid-based sensor for detecting Pd2+ ion under mild conditions.

Herein, a boronic acid-based sensor was reported selectively to recognize Pd2+ ion. The fluorescence intensity increased 36-fold after sensor binding with 2.47 × 10-5 M of Pd2+ ion. It was carried out in the 99% aqueous solution for binding tests, indicating sensor having good water solubility. In addition, it is discernible that Pd2+ ion turned on the blue fluorescence of sensor under a UV-lamp (365 nm), while other ions (Ag+, Al3+, Ba2+, Ca2+, Cr2+, Cd2+, Co2+, Cs2+, Cu2+, Fe2+, Fe3+, K+, Li+, Mg2+, Mn2+, Na+, Ni2+ and Zn2+) did not show the similar change. Furthermore, sensor has a low limit of detection (38 nM) and high selectivity, which exhibits the potential for the development of Pd2+ recognition in practical environments.

A Simplified Method of Synthesis to Obtain Zwitterionic Cellulose under Mild Conditions with Active Ionic Moieties.

A simplified procedure to synthesize zwitterionic cellulose by means of N-protected aspartic anhydride under mild conditions was developed. The preparation of modified cellulose samples was carried out under heterogeneous, aqueous conditions by reacting NH4OH-activated cellulose with aspartic anhydrides N-protected with trifluoroacetyl (TFAc) and carbobenzyloxy (Cbz). Modified cellulose samples Cel-Asp-N-TFAc and Cel-Asp-N-Cbz were characterized by Fourier Transform Infrared (FTIR) and 13C solid state Nuclear Magnetic Resonance (NMR) spectroscopy. The functionalization degree of each cellulose sample was determined by the 13C NMR signal integration values corresponding to the cellulose C1 vs. the Cα of the aspartate residue and corroborated by elemental analysis. In agreement, both analytical methods averaged a grafting degree of 20% for Cel-Asp-N-TFAc and 16% for Cel-Asp-N-Cbz. Conveniently, Cel-Asp-N-TFAc was concomitantly partially N-deprotected (65%) as determined by the ninhydrin method. The zwitterion character of this sample was confirmed by a potentiometric titration curve and the availability of these amino acid residues on the cellulose was inspected by adsorption kinetics method with a 100 mg L-1 cotton blue dye solution. In addition, the synthesis reported in the present work involves environmentally related advantages over previous methodologies developed in our group concerning to zwitterionic cellulose preparation.

Mild Cobalt(III)-Catalyzed Allylative C-F/C-H Functionalizations at Room Temperature.

Sustainable, cobalt-catalyst enabled, synthetically significant C-F/C-H functionalizations were achieved with an ample substrate scope at an ambient temperature of 25 °C, thereby delivering perfluoroallylated heteroarenes. Detailed experimental and computational mechanistic studies on the C-F/C-H functionalizations provided strong support for a facile C-F cleavage.

Characterization of the Micromorphology and Topochemistry of Poplar Wood during Mild Ionic Liquid Pretreatment for Improving Enzymatic Saccharification.

Ionic liquids (ILs) as designer solvents have been applied in biomass pretreatment to increase cellulose accessibility and therefore improve the enzymatic hydrolysis. We investigated the characterization of the micromorphology and the topochemistry of poplar wood during 1-ethyl-3-methylimidazolium acetate pretreatment with mild conditions (90 °C for 20 and 40 min) by multiple microscopic techniques (FE-SEM, CLSM, and CRM). Chemical composition analysis, XRD, cellulase adsorption isotherm, and enzymatic hydrolysis were also performed to monitor the variation of substrate properties. Our results indicated that the biomass conversion was greatly enhanced (from 20.57% to 73.64%) due to the cell wall deconstruction and lignin dissolution (29.83% lignin was removed after incubation for 40 min), rather than the decrystallization or crystallinity transformation of substrates. The mild ILs pretreatment, with less energy input, can not only enhance enzymatic hydrolysis, but also provide a potential approach as the first step in improving the sequential pretreatment effectiveness in integrated methods. This study provides new insights on understanding the ILs pretreatment with low temperature and short duration, which is critical for developing individual and/or combined pretreatment technologies with reduced energy consumption.

Design Photocatalysts to Boost Carrier Dynamics in Plastics Photoconversion into Fuels.

Solar-driven plastics conversion into valuable fuels has attracted broad attention in recent years, which has enormous potential for plastics recycling in the future. However, it usually encounters low conversion efficiency, where one of the reasons is attributed to the poor carrier dynamics in the photocatalytic process. In this Perspective, we critically review the developed strategies, involving defect engineering, doping engineering, heterojunction engineering, and composite construction, for boosted carrier separation efficiency. In addition, we provide an outlook for more potential strategies to engineer catalysts for promoted carrier dynamics. Finally, we also propose prospects for the future research direction of plastics photoconversion into fuels.

High yield production of nanocrystalline cellulose from corn cob through a chemical-mechanical treatment under mild conditions.

Agricultural biomass waste such as corn cob is available in large quantities and can be used as renewable materials for various applications. Corn cob was converted into nanocrystalline cellulose by using mild sulfuric acid concentrations (30 % w/v) at low temperature (50 °C) and a relatively shorter time extraction (30 min) combined with mechanical treatment using a conventional high-speed blender. NCC from cellulose and α-cellulose from corn cobs have been successfully isolated with relatively high yields and crystallinities of 50.07-65.33 % and 65.5-69.9 %, respectively. Scanning electron microscopy (SEM) evaluated the morphological variation and dimension from corn cob fiber (CF), delignification fiber (DF), cellulose, and α-cellulose, which shows that each pretreatment stage causes a decrease in fiber diameter from 16.56 to 5.48 µm. Transmission electron microscopy (TEM) images confirmed the nano-scale dimension with fiber diameters ranging between 9.35 nm and 6.51 nm. Thermogravimetric analysis shows that NCC has relatively high thermal stability ranging from 429 to 437 °C. Thus, this characteristic of NCC has the potential to be applied as a reinforcing agent in various fields of polymer composites. Finally, this study presents a method for isolating NCC from corncob waste using a conventional high-speed blender in a mild condition process with a relatively low cost, environmentally friendly pathway, and high yield that was still preserved.

Visible-Light-Driven Porphyrin-Based Bimetallic Metal-Organic Frameworks for Selective Photoreduction of Nitro Compounds under Mild Conditions.

Selective reduction of nitroaromatics to the corresponding amines generally requires complex conditions, involving pressurized hydrogen, higher temperatures, or organic acids. In this work, we successfully prepared a series of porphyrin-based MOF photocatalysts (Pd-PMOFs, In-PMOFs, and In/Pd-PMOFs) via a facile solvothermal method for the efficient selective reduction of nitroaromatics to corresponding anilines with deionized water as the hydrogen donor. Being a new structured material (monoclinic, C52H40InN6O8Pd), on account of the abundant pore channels, strong light absorption capability, well-matched bandgap, as well as the coordination of indium ions and palladium ions, In/Pd-MOFs have excellent migration efficiency of photo-induced electrons and holes. Specifically, the In/Pd-PMOF photocatalyst manifested superior conversion (100%) and selectivity (≥80%) toward the screened nitro compounds under mild conditions. This work avoids the use of strong reductants, organic acids, and pressurized hydrogen gas as hydrogen sources, providing a promising concept for developing green catalytic systems.

A Conceptual Approach for the Design of New Catalysts for Ammonia Synthesis: A Metal-Support Interactions Review.

The growing interest in green ammonia production has spurred the development of new catalysts with the potential to carry out the Haber-Bosch process under mild pressure and temperature conditions. While there is a wide experimental background on new catalysts involving transition metals, supports and additives, the fundamentals behind ammonia synthesis performance on these catalysts remained partially unsolved. Here, we review the most important works developed to date and analyze the traditional catalysts for ammonia synthesis, as well as the influence of the electron transfer properties of the so-called 3rd-generation catalysts. Finally, the importance of metal-support interactions is highlighted as an effective pathway for the design of new materials with potential to carry out ammonia synthesis at low temperatures and pressures.

A Facile Synthetic Approach to UV-Degradable Hydrogels.

Light-degradable hydrogels have a wide range of application prospects in the field of biomedicine. However, the provision of a facile synthetic approach to light-degradable hydrogels under mild conditions remains a challenge for researchers. To surmount this challenge, a facile synthetic approach to UV-degradable hydrogels is demonstrated in this manuscript. Initially, an UV-degradable crosslinker (UVDC) having o-nitrobenzyl ester groups was synthesized in a single step through the employment of the Passerini three-component reaction (P-3CR). Both 1H NMR and MS spectra indicated the successful synthesis of high-purity UVDC, and it was experimentally demonstrated that the synthesized UVDC was capable of degradation under 368 nm light. Furthermore, this UVDC was mixed with 8-arm PEG-thiol (sPEG20k-(SH)8) to promptly yield an UV-degradable hydrogel through a click reaction. The SEM image of the fabricated hydrogel exhibits the favorable crosslinking network of the hydrogel, proving the successful synthesis of the hydrogel. After continuous 368 nm irradiation, the hydrogel showed an obvious gel-sol transition, which demonstrates that the hydrogel possesses a desirable UV-degradable property. In summary, by utilizing solely a two-step reaction devoid of catalysts and hazardous raw materials, UV-degradable hydrogels can be obtained under ambient conditions, which greatly reduces the difficulty of synthesizing light-degradable hydrogels. This work extends the synthetic toolbox for light-degradable hydrogels, enabling their accelerated development.

Benzimidazol-2-ylidene ruthenium complexes for C-N bond formation through alcohol dehydrogenation.

A low temperature hydrogen borrowing approach to generate secondary amines using benzimidazole-based N-heterocyclic carbene (BNHC) ruthenium complexes is reported. A series of the piano-stool complexes of the type [(η6-p-cymene)(BNHC)RuCl2] (1a-g) were synthesized via one-pot reaction of the NHC salt precursor, Ag2O, and [RuCl2(p-cymene)]2 and characterized using conventional spectroscopic techniques. The geometry of two precursors, [(η6-p-cymene)(Me4BnMe2BNHCCH2OxMe)RuCl2] (1f) and [(η6-p-cymene)(Me5BnMe2BNHCCH2OxMe)RuCl2] (1g), was studied by single crystal X-ray diffraction. These catalysts were found to dehydrogenate alcohols efficiently at temperatures as low as 50 °C to allow Schiff-base condensation and subsequent imine hydrogenation to afford secondary amines. Notably, this ruthenium-based procedure enables the N-alkylation of aromatic and heteroaromatic primary amines with a wide range of primary alcohols in excellent yields of up to 98%. The present methodology is green and water is liberated as the sole byproduct.