RESUMEN
We propose an alternating current (AC) field operation scheme by using an asymmetric voltage waveform to improve the electroluminescence property of AC field-induced electroluminescence (AC-FIEL) devices. Hole injection and transport can be improved by carbon nanotubes (CNT) doping into the emission layer of an AC-FIEL structure operated by a single electrode for AC-responsive alternating carrier injections. However, under an AC operation, highly unbalanced charge transports are inevitably present in CNT-doped AC-FIEL devices due to faster carrier paths through CNTs. Compared with symmetric waveform, asymmetric waveform can be adjusted to allow longer relative duty time for faster carriers in which the luminance level of CNT-doped AC-FIEL devices can be improved by 1.4 times at the same device structure and operation frequency condition.
RESUMEN
We herein propose a multiwalled carbon nanotube (MWCNT) doping method into liquid crystal (LC) alignment polyimides (PIs) with low resistivity for resolving both issues of voltage holding and image sticking in low-frequency-driven fringe-field switching (FFS) LC modes using negative dielectric LCs (n-LCs). By utilizing strong ion trapping ability of MWCNTs, the FFS n-LC cell aligned by low resistivity PIs with 0.05 wt% MWCNT doping exhibited an excellent voltage holding ratio of 99% under an extremely low operation frequency of 0.5 Hz and approximately 23.6 times better surface discharging property than that aligned by high resistivity PIs.
RESUMEN
We proposed and analyzed an optically isotropic nano-droplet liquid crystal (LC) doped with high k nanoparticles (NPs), exhibiting enhanced Kerr effects, which could be operated with reduced driving voltages. For enhancing the contrast ratio together with the light efficiencies, the LC droplet sizes were adjusted to be shorter than the wavelength of visible light to reduce depolarization effects by optical scattering of the LC droplets. Based on the optical analysis of the depolarization effects, the influence of the relationship between the LC droplet size and the NP doping ratio on the Kerr effect change was investigated.
RESUMEN
We analyzed a transient blinking phenomenon in a fringe-field switching liquid crystal (LC) mode that occurred at the moment of frame change even in the optimized DC offset condition for minimum image flicker. Based on the positional dynamic behaviors of LCs by using a high-speed camera, we found that the transient blink is highly related to the asymmetric responses of the splay-bend transitions caused by the flexoelectric (FE) effect. To remove the transient blink, the elastic property adjustment of LCs was an effective solution because the FE switching dynamics between the splay-enhanced and bend-enhanced deformations are highly dependent on the elastic constants of LCs, which is the cause of momentary brightness drop.
RESUMEN
We propose a highly oriented photochromic dye film for an ultraviolet (UV)-sensing layer, where spirooxazine (SO) derivatives are aligned with the liquid crystalline UV-curable reactive mesogens (RM) using a guest-host effect. For effective electrical UV sensing with a simple metal-insulator-metal structure, our results show that the UV-induced switchable dipole moment amount of the SO derivatives is high; however, their tilting orientation should be controlled. Compared to the dielectric layer with the nearly planar SO dye orientation, the photochromic dielectric layer with the moderately tilted dye orientation shows more than seven times higher the UV-induced capacitance variation.
RESUMEN
Optical profilometry is widely applied for measuring the morphology of objects by projecting predetermined patterns on them. In this technique, the compact size is one of the interesting issues for practical applications. The generation of pattern by the interference of coherent light sources has a potential to reduce the dimension of the illumination part. Moreover, this method can make fine patterns without projection optics, and the illumination part is free of restriction from the numerical aperture of the projection optics. In this paper, a phase-shifting profilometry is implemented by using a single liquid crystal (LC) cell. The LC phase modulator is designed to generate the interference patterns with several different spatial frequencies by changing selection of the spacing between the micro-pinholes. We manufactured the LC phase modulator and calibrated it by measuring the phase modulation amount depending on an applied voltage. Our optical profilometry using the single LC cell can generate multi-spatial frequency patterns as well as four steps of the phase-shifted patterns. This method can be implemented compactly, and the reconstructed depth profile is obtained without a phase-unwrapping algorithm.
RESUMEN
We demonstrate the first-ever surface modification of green CdSe/ZnS quantum dots (QDs) using bromide anions (Br-) in cetyl trimethylammonium bromide (CTAB). The Br- ions reduced the interparticle spacing between the QDs and induced an effective charge balance in QD light-emitting devices (QLEDs). The fabricated QLEDs exhibited efficient charge injection because of the reduced emission quenching effect and their enhanced thin film morphology. As a result, they exhibited a maximum luminance of 71,000 cd/m2 and an external current efficiency of 6.4 cd/A, both significantly better than those of their counterparts with oleic acid surface ligands. In addition, the lifetime of the Br- treated QD based QLEDs is significantly improved due to ionic passivation at the QDs surface.