Enhancing bioflocculation in high-rate activated sludge improves effluent quality yet increases sensitivity to surface overflow rate.

High-rate activated sludge (HRAS) relies on good bioflocculation and subsequent solid-liquid separation to maximize the capture of organics. However, full-scale applications often suffer from poor and unpredictable effluent suspended solids (ESS). While the biological aspects of bioflocculation are thoroughly investigated, the effects of fines (settling velocity < 0.6 m3/m2/h), shear and surface overflow rate (SOR) are unclear. This work tackled the impact of fines, shear, and SOR on the ESS in absence of settleable influent solids. This was assessed on a full-scale HRAS step-feed (SF) and pilot-scale HRAS contact-stabilization (CS) configuration using batch settling tests, controlled clarifier experiments, and continuous operation of reactors. Fines contributed up to 25% of the ESS in the full-scale SF configuration. ESS decreased up to 30 mg TSS/L when bioflocculation was enhanced with the CS configuration. The feast-famine regime applied in CS promoted the production of high-quality extracellular polymeric substances (EPS). However, this resulted in a narrow and unfavorable settling velocity distribution, with 50% ± 5% of the sludge mass settling between 0.6 and 1.5 m3/m2/h, thus increasing sensitivity towards SOR changes. A low shear environment (20 s-1) before the clarifier for at least one min was enough to ensure the best possible settling velocity distribution, regardless of prior shear conditions. Overall, this paper provides a more complete view on the drivers of ESS in HRAS systems, creating the foundation for the design of effective HRAS clarifiers. Tangible recommendations are given on how to manage fines and establish the optimal settling velocity of the sludge.

Thermodynamic Analysis of Intermediary Metabolic Steps and Nitrous Oxide Production by Ammonium-Oxidizing Bacteria.

Nitrous oxide (N2O) is a greenhouse gas emitted from wastewater treatment, soils, and agriculture largely by ammonium-oxidizing bacteria (AOB). While AOB are characterized by being aerobes that oxidize ammonium (NH4+) to nitrite (NO2-), fundamental studies in microbiology are revealing the importance of metabolic intermediates and reactions that can lead to the production of N2O. These findings about the metabolic pathways for AOB were integrated with thermodynamic electron-equivalents modeling (TEEM) to estimate kinetic and stoichiometric parameters for each of the AOB's nitrogen (N)-oxidation and -reduction reactions. The TEEM analysis shows that hydroxylamine (NH2OH) oxidation to nitroxyl (HNO) is the most energetically efficient means for the AOB to provide electrons for ammonium monooxygenation, while oxidations of HNO to nitric oxide (NO) and NO to NO2- are energetically favorable for respiration and biomass synthesis. The respiratory electron acceptor can be O2 or NO, and both have similar energetics. The TEEM-predicted value for biomass yield, maximum-specific rate of NH4+ utilization, and maximum specific growth rate are consistent with empirical observations. NO reduction to N2O is thermodynamically favorable for respiration and biomass synthesis, but the need for O2 as a reactant in ammonium monooxygenation likely precludes NO reduction to N2O from becoming the major pathway for respiration.

Vacuum-enhanced anaerobic fermentation: Achieving process intensification, thickening and improved hydrolysis and VFA yields in a single treatment step.

This study assessed the feasibility of a novel vacuum-enhanced anaerobic digestion technology, referred to as IntensiCarbTM (IC), under mild vacuum pressure (110 mbar), compared to a control (conventional fermenter), and evaluated the impact of the vacuum on the activities of various microbial groups. Both fermenters (test and control) were operated with mixed (50% v/v) municipal sludge at solids concentrations of 2-2.5%, pH of 7.8-8.1, 40-45 °C, a theoretical solids retention time (SRT) of 3 days with different hydraulic retention times (HRT). The intensification factor (IF) of the IC, defined as SRT/HRT, was controlled at 1.3 and 2.0. Simultaneous thickening and fermentation intensification were achieved. Compared with the control, the IC, despite the shorter HRTs, achieved 29.5 to 90.2% increase in the VFA yield (79 to 116 mg ΔVFA/ g VSS vs 61 mg ΔVFA/ g VSS), and 16.2% to 56.4% increase (280 to 377 mg ΔsCOD/ g VSS vs 241 mg ΔsCOD/ g VSS), in the hydrolysis yield. Fermentate from the IC exhibited comparable specific denitrification rates to acetate. Further, the solids-free condensate contained low nutrient concentrations, and thus was far superior to a typical centrates from dewatering as a carbon source. No adverse effects of vacuum on the activity of fermentative bacteria and methanogens were observed. This study demonstrated that the IC can be deployed as an intensification technology for both fermentation and anaerobic digestion of biosolids with the additional significant advantage, i.e. elimination of sidestream ammonia treatment requirements.

Media selection for anammox-based polishing filters: Balancing anammox enrichment and retention with filtration function.

Retrofitting conventional denitrification filters into partial denitrification-anammox (PdNA)- or anammox (AnAOB)-based filters will reduce the needs for external carbon addition. The success of AnAOB-based filters depends on anammox growth and retention within such filters. Studies have overlooked the importance of media selection and its impact on AnAOB capacity, head loss progression dynamics, and shear conditions applied onto the AnAOB biofilm. The objective of this study was to evaluate viable media types (10 types) that can enhance AnAOB rates for efficient nitrogen removal in filters. Given the higher backwash requirement and lower AnAOB capacity of the conventionally used sand, expanded clay (3-5 mm) was recommended for AnAOB-based filters in this study. Owing to its surface characteristics, expanded clay had higher AnAOB activity (304- vs. 104-g NH4 + -N/m2 /day) and higher AnAOB retention (43% more) than sand. Increasing the iron content of expanded clay to 37% resulted in an increase in zeta potential, which led to 56% more anammox capacity compared to expanded clay with 7% iron content. This work provides insight into the importance of media types in the growth and retention of AnAOB in filters, and this knowledge could be used as basis in the development of PdNA filters. PRACTITIONER POINTS: Expanded clay showed the lowest head loss buildup and most likely will result in longer runtime for full-scale PdNA applications The highest AnAOB rates were achieved in expanded clay types and sand compared with smaller media typically used in biofiltration Expanded clay resulted in better AnAOB retention under shear, whereas sand could not withstand shear and required more frequent backwashing Expanded clay iron coating enhanced AnAOB enrichment and retention, most likely due to increased surface roughness and/or positive charge.

Mainstream short-cut N removal modelling: current status and perspectives.

This work gives an overview of the state-of-the-art in modelling of short-cut processes for nitrogen removal in mainstream wastewater treatment and presents future perspectives for directing research efforts in line with the needs of practice. The modelling status for deammonification (i.e., anammox-based) and nitrite-shunt processes is presented with its challenges and limitations. The importance of mathematical models for considering N2O emissions in the design and operation of short-cut nitrogen removal processes is considered as well. Modelling goals and potential benefits are presented and the needs for new and more advanced approaches are identified. Overall, this contribution presents how existing and future mathematical models can accelerate successful full-scale mainstream short-cut nitrogen removal applications.

A proof-of-concept experimental study for vacuum-driven anaerobic biosolids fermentation using the IntensiCarb technology.

This study demonstrates the potential of an innovative anaerobic treatment technology for municipal biosolids (IntensiCarb), which relies on vacuum evaporation to decouple solids and hydraulic retention times (SRT and HRT). We present proof-of-concept experiments using primary sludge and thickened waste activated sludge (50-50 v/v mixture) as feed for fermentation and carbon upgrading with the IntensiCarb unit. IntensiCarb fully decoupled the HRT and SRT in continuously stirred anaerobic reactors (CSAR) to achieve two intensification factors, that is, 1.3 and 2, while keeping the SRT constant at 3 days (including in the control fermenter). The intensified CSARs were compared to a conventional control system to determine the yields of particulate hydrolysis, VFA production, and nitrogen partitioning between fermentate and condensate. The intensified CSAR operating at an intensification factor 2 achieved a 65% improvement in particulate solubilization. Almost 50% of total ammonia was extracted without pH adjustment, while carbon was retained in the fermentate. Based on these results, the IntensiCarb technology allows water resource recovery facilities to achieve a high degree of plant-wide intensification while partitioning nutrients into different streams and thickening solids. PRACTITIONER POINTS: The IntensiCarb reactor can decouple hydraulic (HRT) and solids (SRT) retention times in anaerobic systems while also increasing particulate hydrolysis and overall plant capacity. Using vacuum as driving force of the IntensiCarb technology, the system could achieve thickening, digestion, and partial dewatering in the same unit-thus eliminating the complexity of multi-stage biosolids treatment lines. The ability to partition nutrients between particulate, fermentate, and condensate assigns to the IntensiCarb unit a key role in recovery strategies for value-added products such as nitrogen, phosphorus, and carbon, which can be recovered separately and independently.

Unravelling adaptation of nitrite-oxidizing bacteria in mainstream PN/A process: Mechanisms and counter-strategies.

Stable suppression of nitrite-oxidizing bacteria (NOB) is still a major challenge for the implementation of partial nitritation and anammox (PN/A) in mainstream treatment. Despite numerous suppression strategies demonstrated, it is increasingly recognized that NOB could develop resistance to these strategies, threatening the long-term stability of the mainstream PN/A process. This study aims to understand adaption mechanisms and develop counter-strategies to overcome the adaptation. To this end, three previously-demonstrated suppression strategies, including NOB inactivation via side stream sludge treatment with free ammonia (FA), the use of low dissolved oxygen (DO), and the use of anammox to scavenge nitrite, were stepwise applied, over a period of 800 days, to a laboratory-scale reactor treating effluent from a high-rate activated sludge (HRAS) plant. FA sludge treatment alone sustained nitrite accumulation for about two months, after which NOB adaptation occurred causing PN to fail. The FA adaptation was induced by a shift in the NOB community from Nitrospira to Ca. Nitrotoga. The latter was found to have higher resistance to FA and also a higher maximum specific growth rate. Low DO at 0.2-0.4 mg O2 L-1 was then applied, in conjunction with FA treatment, which successfully eliminated Ca. Nitrotoga and re-established PN. However, new and unidentified NOB with a higher apparent oxygen affinity emerged in three months, again leading to PN failure. Lastly, as the third strategy for NOB suppression, anammox was introduced as an in-situ nitrite-scavenger. The combo-strategy delivered reliable NOB suppression with no further adaptation in the remaining experimental period (eight months). The resulted one-stage PN/A reactor achieved a nitrogen removal efficiency of 84.2 ± 5.37%. A control reactor, operated in parallel under the same conditions but without FA treatment, only achieved 10.4 ± 4.6% nitrogen removal, with anammox completely outcompeted by NOB in the last phase.

Robust Nitritation Sustained by Acid-Tolerant Ammonia-Oxidizing Bacteria.

Oxidation of ammonium to nitrite rather than nitrate, i.e., nitritation, is critical for autotrophic nitrogen removal. This study demonstrates a robust nitritation process in treating low-strength wastewater, obtained from a mixture of real mainstream sewage with sidestream anaerobic digestion liquor. This is achieved through cultivating acid-tolerant ammonia-oxidizing bacteria (AOB) in a laboratory nitrifying bioreactor at pH 4.5-5.0. It was shown that nitrite accumulation with a high NO2-/(NO2- + NO3-) ratio of 95 ± 5% was stably maintained for more than 300 days, and the obtained volumetric NH4+ removal rate (i.e., 188 ± 14 mg N L-1 d-1) was practically useful. 16S rRNA gene sequencing analyses indicated the dominance of new AOB, "Candidatus Nitrosoglobus," in the nitrifying guild (i.e., 1.90 ± 0.08% in the total community), with the disappearance of typical activated sludge nitrifying microorganisms, including Nitrosomonas, Nitrospira, and Nitrobacter. This is the first identification of Ca. Nitrosoglobus as key ammonia oxidizers in a wastewater treatment system. It was found that Ca. Nitrosoglobus can tolerate low pH (<5.0), and free nitrous acid (FNA) at levels that inhibit AOB and nitrite-oxidizing bacteria (NOB) commonly found in wastewater treatment processes. The in situ inhibition of NOB leads to accumulation of nitrite (NO2-), which along with protons (H+) also produced in ammonium oxidation generates and sustains FNA at 3.0 ± 1.4 mg HNO2-N L-1. As such, robust PN was achieved under acidic conditions, with a complete absence of NOB. Compared to previous nitritation systems, this acidic nitritation process is featured by a higher nitric oxide (NO) but a lower nitrous oxide (N2O) emission level, with the emission factors estimated at 1.57 ± 0.08 and 0.57 ± 0.03%, respectively, of influent ammonium nitrogen load.

The inhibitory impact of ammonia on thermally hydrolyzed sludge fed anaerobic digestion.

This study evaluated the impact of ammonia on mesophilic anaerobic digestion (AD) with thermal hydrolysis pretreatment (THP) treating a mixture of primary sludge and waste activated sludge and operated under constant organic loading rate of 9 kg COD/m3 /d. Free ammonia concentrations in the digesters were varied between 37 and 966 mg NH3 -N/L, while maintaining all other operational conditions constant. A decrease in volatile solids reduction from 54 ± 5% (at <554 mg NH3 -N/L) to 35 ± 6% at the maximum free ammonia concentration of 966 mg NH3 -N/L was observed at steady-state conditions. No impact of free ammonia on final dewaterability was detected. Free ammonia thus mostly limited methanogenesis. A free ammonia Monod inhibition constant of 847 ± 222 mg NH3 -N/L for methanogens was estimated based on the digester steady-state methane rates dynamics. This study showed that current THP AD digesters (typically 110-260 mg NH3 -N/L) operate under 12%-18% ammonia inhibition for methanogenesis. Operation under SRT of 15 days, about 2 times more than needed to retain methanogens, can compensate for lower methanogens rates and avoid performance impacts. The later shows a good potential to operate under higher free and total ammonia concentration without jeopardizing performance. PRACTITIONER POINTS: Only from a free ammonia concentration above 554 mg NH3 -N/L, decreased volatile solids reduction and biogas yield were observed. A volatile solids reduction of 35 ± 6% at maximum free ammonia concentration of 966 mg NH3 -N/L was still achieved. A Monod inhibition constant for methanogens of 847 ± 222 mg NH3 -N/L was estimated. It was estimated that current THP AD systems (110-260 mg NH3 -N/L) operate under 12%-18% NH3 inhibition for methanogenesis.

Investigating the dynamics of volatile sulfur compound emission from primary systems at a water resource recovery facility.

This study quantifies volatile sulfur compound (VSC) emissions from primary settling tanks and investigates their mechanisms of generation. Hydrogen sulfide (H2 S) and methyl mercaptan (MM) concentrations in the off-gas were dominant among the VSCs analyzed, while dimethyl sulfide (DMS) and dimethyl disulfide (DMDS) were under their odor threshold for most sampling dates. H2 S emission in primary settling tanks was mainly the result of the stripping of dissolved sulfide (64%) generated in the sewers. Results indicate that MM emission was more dependent on the conditions in the primary clarifiers (only 16% stripping). Prevention of odor emission in primary settling tanks can be achieved by managing biofilms and microbial reactions in the sewer network. Controlling the biomass seeding and fermentation product availability in the primary settling tanks is essential to significantly minimize the kinetics of H2 S and MM generation. Overall, the management of sludge blanket heights and thus avoiding time at low oxidation-reduction potential minimized odor emission independent of sewer conditions. PRACTITIONER POINTS: H2 S emission from primary clarifiers mainly originated from the stripping of the dissolved sulfide formed in the sewers. MM emission contributed for 89% to overall odor emitted from primary clarifiers. Seeding of active biomass from the sewer into the primary clarifiers was be the main driver for both MM and H2 S formation. Increased availability of fermentation products or fermenters increased MM production.

Towards more predictive clarification models via experimental determination of flocculent settling coefficient value.

Improved settleability has become an essential feature of new wastewater treatment innovations. To accelerate adoption of such new technologies, improved clarifier models are needed to help with designing and predicting improvement in settleability. In general, the level of mathematics of settling clarifier models has gone far beyond the level of existing experimental methods available to support these models. To date, even for simple one-dimensional (1D) clarifier models, no experimental method has been described for flocculent settling coefficient (rp). As a consequence, rp cannot be considered as a sludge characteristic and is used as a calibration parameter to achieve observed effluent quality. In this study, we focused on the development of an empirical function based on a simple and practical experimental approach for the calculation of the rp value from sludge characteristics. This approach provided a similar approach as currently taken for hindered settling coefficient calculations (Veslind equation) and allowed for the model to predict effluent quality, thus increasing the power of the 1D model. The threshold of flocculation (TOF), which describes the collision efficiency of particles, directly correlated with the effluent quality of the five tested activated sludge systems and was selected as experimental method. The proposed empirical function between TOF and rp was validated for four years of validating data with five different sludge types operated under different operational conditions and configurations. The good effluent quality prediction with this approach brings us one step closer in making the clarification models more predictive towards effluent quality and clarifier performance.

Primary sludge fermentate as carbon source for mainstream partial denitrification-anammox (PdNA).

Primary sludge fermentate, a concentrated hydrolyzed wastewater carbon, was evaluated for use as an alternative carbon source for mainstream partial denitrification-anammox (PdNA) in a suspended growth activated sludge process in terms of partial denitrification (PdN) efficiency, PdNA nitrogen removal contributions, and final effluent quality. Fermenter operation at a 2-day sludge retention time (SRT) resulted in the maximum achievable yield of 0.14 ± 0.05 g sCOD/g VSS without release of excessive ammonia and phosphorus to the system. Based on the results of batch experiments, fermentate addition led to PdN efficiency of 93 ± 14%, which was similar to acetate at a nitrate residual of 2-3 mg N/L. In the pilot-scale mainstream deammonification reactor, PdN efficiency using fermentate was 49 ± 24%, which was lower than acetate (66 ± 24% during acetate period I and 70 ± 21% during acetate period II), most probably due to lower nitrate and ammonium kinetics in the PdN zone. Methanol cost-saving potential for the application of PdNA as the main short-cut nitrogen pathway was estimated to be 30% to 55% depending on the PdN efficiency achieved. PRACTITIONER POINTS: Primary sludge fermentate was evaluated as an alternative carbon source for mainstream partial denitrification-anammox (PdNA). Fermenter operated at a 1 to 2 day SRT resulted in the maximum achievable yield without the release of excessive ammonia and phosphorus to the system. Although 93% partial denitrification efficiency was achieved with fermentate in batch experiments, around 49% PdN efficiency was achieved in pilot studies. Application of PdNA with fermentate can result in significant methanol cost savings.

Increasing oxygen transfer efficiency through sorption enhancing strategies.

The link between aeration efficiency and biosorption capacity in water resource recovery facilities was extensively investigated, with special emphasis on wastewater characteristics and the development of strategies to maximize adsorption. Biosorption of oxygen transfer inhibitors (i.e., surfactants, colloidal, and soluble fractions) was examined by a series of pilot batch-scale experiments and full-scale studies. The impact of a sorption-enhancing strategy (i.e., bioaugmentation) deployed at full-scale over a five-year period was evaluated. Bench-scale experiments determined the inhibition coefficient (Ki) to measure the impact of surfactants and COD fractions as inhibitors of oxygen transfer efficiencies (αSOTE) in wastewater systems. The inhibition constant for surfactants Ki was found at 2.4 ± 0.4 mg L-1 SDS while for colloidal material was at 14 ± 1 mg L-1 (no inhibition for soluble fraction was found). Two enhancing biosorption configurations (i.e., contact stabilization and anaerobic selector) resulted in significant improvements in both aeration efficiency indicators (αSOTE) and surfactants removals. αSOTE improvements of 46% and 54% in comparison to conventional high rate activated sludge process (HRAS) were reported. Similarly, the removal of surfactants was increased by 27% and 56% using optimized enhancing-sorption strategies. Further analyses helped elucidate the underlying mechanisms of surfactants removal. Findings are expected to help full-scale applications increase their sorption potential as well as the concurrent aeration efficiency, which helps WRRFs to advance toward energy-positive wastewater treatments.

Recuperative thickening for sludge retention time and throughput management in anaerobic digestion with thermal hydrolysis pretreatment.

This study evaluated the application of recuperative thickening (RT) to enhance anaerobic digestion (AD) performance for AD systems with thermal hydrolysis pretreatment (THP). RT was applied for two different reasons: (a) for increasing the sludge retention time (SRT) to degrade slowly hydrolyzable materials more efficiently and (b) for maintaining SRT at decreased hydraulic retention time (HRT) thus showing potential for increased AD throughput rates. A SRT increase from 15 to 30 days by RT application did not improve AD performance or hydrolysis rates significantly as 15-day SRT was already a factor 2 higher than the estimated washout SRT. When applying RT to increase throughput rates (HRT of 7 days) while maintaining 15-day SRT, no negative impact on biogas production or hydrolysis kinetics was observed. It was estimated that RT application on THP digesters can increase digester throughput by 100% and thus show clear potential for further AD intensification. PRACTITIONER POINTS: Increased SRT from 15 to 30 days through recuperative thickening application did not improve biogas production. A lower required minimum SRT (6-7 days) was estimated in THP-AD systems compared to conventional AD. Operation at decreased HRT by RT application resulted in similar AD performance under constant organic loading rates. A 100% increase in throughput rates can be applied using RT without decreasing AD performance.

Exploring the impact of bulk and substrate physics on hydrolysis rates and biogas yields of anaerobic digesters pretreated with thermal hydrolysis.

This study evaluated the role of bulk and substrate physics on hydrolysis rates and biogas yields in anaerobic digestion (AD) pretreated by thermal hydrolysis (THP). Although THP decreases sludge viscosity, no evidence was found that bulk viscosity impacted the biogas yield or hydrolysis kinetics. In addition, no significant difference between the biogas yields for different total solids concentrations nor floc sizes was detected. However, increased mixing speeds did increase biogas yields. As a result of thermal treatment, the model protein, bovine serum albumin, was harder to degrade in terms of both overall biodegradability and hydrolysis rates when their macrostructures were changed from liquid to gel and to solid structures; the opposite was true for the model polysaccharide, amylopectin. These results demonstrated that hydrolysis in THP-AD systems was impacted mostly by the physical properties of the substrate (gelation) rather than the bulk physical properties within the digester. PRACTITIONER POINTS: Bulk viscosity does not significantly impact hydrolysis efficiency (biogas yield). However, mixing speed impacts hydrolysis beyond biogas holdup effect. Increasing the amount of substrate-microbe collisions through increasing biomass concentration does not have an impact on hydrolysis efficiency or biogas yield. Proteins are harder to degrade when macrostructure changes from liquid to gel/solid as a result of heat treatment. Polysaccharides are easier to degrade when macrostructure changes from liquid to gel/solid as a result of heat treatment. The time required for digesters to reach peak biogas production rates increased with decreasing specific surface available on gel and solid structures.

Nitrate residual as a key parameter to efficiently control partial denitrification coupling with anammox.

Despite the increased research efforts, full-scale implementation of shortcut nitrogen removal strategies has been challenged by the lack of consistent nitrite-oxidizing bacteria out-selection. This paper proposes an alternative path using partial denitrification (PdN) selection coupled with anaerobic ammonium-oxidizing bacteria (AnAOB). A nitrate residual concentration (>2 mg N/L) was identified as the crucial factor for metabolic PdN selection using acetate as a carbon source, unlike the COD/N ratio which was often suggested. Therefore, a novel and simple acetate dosing control strategy based on maintaining a nitrate concentration was tested in the absence and presence of AnAOB, achieving PdN efficiencies above 80%. The metabolic-based PdN selection allowed for flexibility to move between PdN and full denitrification when required to meet effluent nitrate levels. Due to the independence of this strategy on species selection and management of nitrite competition, this novel approach will guarantee nitrite availability for AnAOB under mainstream conditions unlike shortcut nitrogen removal approaches based on NOB out-selection. Overall, a COD addition of only 2.2 g COD/g TIN removed was needed for the PdN-AnAOB concept showing its potential for significant savings in external carbon source needs to meet low TIN effluent concentrations making this concept a competitive alternative. PRACTITIONER POINTS: Nitrate residual is the key control parameter for partial denitrification selection. Metabolic selection allowed for flexibility of moving from partial to full denitrification. 2.2 g COD/g TIN removed was needed for partial denitrification-anammox process.

Colloids, flocculation and carbon capture - a comprehensive plant-wide model.

The implementation of carbon capture technologies such as high-rate activated sludge (HRAS) systems are gaining interests in water resource and recovery facilities (WRRFs) to minimize carbon oxidation and maximize organic carbon recovery and methane potential through biosorption of biodegradable organics into the biomass. Existing activated sludge models were developed to describe chemical oxygen demand (COD) removal in activated sludge systems operating at long solids retention times (SRT) (i.e. 3 days or longer) and fail to simulate the biological reactions at low SRT systems. A new model is developed to describe colloidal material removal and extracellular polymeric substance (EPS) generation, flocculation, and intracellular storage with the objective of extending the range of whole plant models to very short SRT systems. In this study, the model is tested against A-stage (adsorption) pilot reactor performance data and proved to match the COD and colloids removal at low SRT. The model was also tested on longer SRT systems where effluents do not contain much residual colloids, and digestion where colloids from decay processes are present.

'Hot topic' - combined energy and process modeling in thermal hydrolysis systems.

The thermal hydrolysis process (THP) is applied to enhance biogas production in anaerobic digestion (AD), reduce viscosity for improved mixing and dewatering and to reduce and sterilize cake solids. Large heat demands for steam production rely on dynamic effects like sludge throughput, gas availability and THP process parameters. Here, we propose a combined energy and process model suitable to describe the dynamic behaviour of THP in a full-plant context. The process model addresses interactions of THP with operational conditions covered by the AD model obeying mass continuity. Energy conservation is considered in balancing and converting various energy species dominated by thermal heat and calorific energy. The combined energy and process model was then applied on the THP at Blue Plains advanced WWTP (DC Water) to analyse the process and assess potential energy optimizations. It was found that dynamic effects like mismatched steam production and consumption, temporary gas shortages and underloaded units are responsible for energy inefficiencies with losses in electricity-production up to 29%.