A feasibility study of a multimodal stimulation bioreactor for the conditioning of stem cell seeded cardiac patches via electrical impulses and pulsatile perfusion.

BACKGROUND/OBJECTIVE: Ischemic heart disease is a major cause of mortality worldwide. Myocardial tissue engineering aims to create transplantable units of myocardium for the treatment of myocardial necrosis caused by ischemic heart disease - bioreactors are used to condition these bioartificial tissues before application. METHODS: Our group developed a multimodal bioreactor consisting of a linear drive motor for pulsatile flow generation (500 ml/min) and an external pacemaker for electrical stimulation (10 mA, 3 V at 60 Hz) using LinMot-Talk Software to synchronize these modes of stimulation. Polyurethane scaffolds were seeded with 0.750 × 106 mesenchymal stem cells from umbilical cord tissue per cm2 and stimulated in our system for 72 h, then evaluated. RESULTS: After conditioning histology showed that the patches consisted of a cell multilayer surviving stimulation without major damage by the multimodal stimulation, scanning electron microscopy showed a confluent cell layer with no cell-cell interspaces visible. No cell viability issues could be identified via Syto9-Propidium Iodide staining. CONCLUSIONS: This bioreactor allows mechanical stimulation via pulsatile flow and electrical stimulation through a pacemaker. Our stem cell-polyurethane constructs displayed survival after conditioning. This system shows feasibility in preliminary tests.

In vitro biological and mechanical evaluation of various scaffold materials for myocardial tissue engineering.

A cardiac patch is a construct devised in regenerative medicine to replace necrotic heart tissue after myocardial infarctions. The cardiac patch consists of a scaffold seeded with stem cells. To identify the best scaffold for cardiac patch construction we compared polyurethane, Collagen Cell Carriers, ePTFE, and ePTFE SSP1-RGD regarding their receptiveness to seeding with mesenchymal stem cells isolated from umbilical cord tissue. Seeding was tested at an array of cell seeding densities. The bioartificial patches were cultured for up to 35 days and evaluated by scanning electron microscopy, microscopy of histological stains, fluorescence microscopy, and mitochondrial assays. Polyurethane was the only biomaterial which resulted in an organized multilayer (seeding density: 0.750 × 10(6) cells/cm(2)). Cultured over 35 days at this seeding density the mitochondrial activity of the cells on polyurethane patches continually increased. There was no decrease in the E Modulus of polyurethane once seeded with cells. Seeding of CCC could only be realized at a low seeding density and both ePTFE and ePTFE SSP1-RGD were found to be unreceptive to seeding. Of the tested scaffolds polyurethane thus crystallized as the most appropriate for seeding with mesenchymal stem cells in the framework of myocardial tissue engineering.

In vitro comparison of novel polyurethane aortic valves and homografts after seeding and conditioning.

The aim of the study was to compare the behavior of seeded cells on synthetic and natural aortic valve scaffolds during a low-flow conditioning period. Polyurethane (group A) and aortic homograft valves (group B) were consecutively seeded with human fibroblasts (FB), and endothelial cells (EC) using a rotating seeding device. Each seeding procedure was followed by an exposure to low pulsatile flow in a dynamic bioreactor for 5 days. For further analysis, samples were taken before and after conditioning. Scanning electron microscopy showed confluent cell layers in both groups. Immunohistochemical analysis showed the presence of EC and FB before and after conditioning as well as the establishment of an extracellular matrix (ECM) during conditioning. A higher expression of ECM was observed on the scaffolds' inner surface. Real-time polymerase chain reaction showed higher inflammatory response during the conditioning of homografts. Endothelialization caused a decrease in inflammatory gene expression. The efficient colonization, the establishment of an ECM, and the comparable inflammatory cell reaction to the scaffolds in both groups proved the biocompatibility of the synthetic scaffold. The newly developed bioreactor permits conditioning and cell adaption to shear stress. Therefore, polyurethane valve scaffolds may offer a new option for aortic valve replacement.

Use of a special bioreactor for the cultivation of a new flexible polyurethane scaffold for aortic valve tissue engineering.

BACKGROUND: Tissue engineering represents a promising new method for treating heart valve diseases. The aim of this study was evaluate the importance of conditioning procedures of tissue engineered polyurethane heart valve prostheses by the comparison of static and dynamic cultivation methods. METHODS: Human vascular endothelial cells (ECs) and fibroblasts (FBs) were obtained from saphenous vein segments. Polyurethane scaffolds (n = 10) were primarily seeded with FBs and subsequently with ECs, followed by different cultivation methods of cell layers (A: static, B: dynamic). Group A was statically cultivated for 6 days. Group B was exposed to low flow conditions (t1=3 days at 750 ml/min, t2=2 days at 1100 ml/min) in a newly developed conditioning bioreactor. Samples were taken after static and dynamic cultivation and were analyzed by scanning electron microscopy (SEM), immunohistochemistry (IHC), and real time polymerase chain reaction (RT-PCR). RESULTS: SEM results showed a high density of adherent cells on the surface valves from both groups. However, better cell distribution and cell behavior was detected in Group B. IHC staining against CD31 and TE-7 revealed a positive reaction in both groups. Higher expression of extracellular matrix (ICAM, Collagen IV) was observed in Group B. RT- PCR demonstrated a higher expression of inflammatory Cytokines in Group B. CONCLUSION: While conventional cultivation method can be used for the development of tissue engineered heart valves. Better results can be obtained by performing a conditioning step that may improve the tolerance of cells to shear stress. The novel pulsatile bioreactor offers an adequate tool for in vitro improvement of mechanical properties of tissue engineered cardiovascular prostheses.