On the Dependency of the Electromechanical Response of Rotary MEMS/NEMS on Their Embedded Flexure Hinges' Geometry.

This paper investigates how the electromechanical response of MEMS/NEMS devices changes when the geometrical characteristics of their embedded flexural hinges are modified. The research is dedicated particularly to MEMS/NEMS devices which are actuated by means of rotary comb-drives. The electromechanical behavior of a chosen rotary device is assessed by studying the rotation of the end effector, the motion of the comb-drive mobile fingers, the actuator's maximum operating voltage, and the stress sustained by the flexure when the flexure's shape, length, and width change. The results are compared with the behavior of a standard revolute joint. Outcomes demonstrate that a linear flexible beam cannot perfectly replace the revolute joint as it induces a translation that strongly facilitates the pull-in phenomenon and significantly increases the risk of ruptures of the comb-drives. On the other hand, results show how curved beams provide a motion that better resembles the revolute motion, preserving the structural integrity of the device and avoiding the pull-in phenomenon. Finally, results also show that the end effector motion approaches most precisely the revolute motion when a fine tuning of the beam's length and width is performed.

Assessing the consequences of prolonged usage of disposable face masks.

Due to the SARS-CoV-2 outbreak, wearing a disposable face mask has become a worldwide daily routine, not only for medical operators or specialized personnel, but also for common people. Notwithstanding the undeniable positive effect in reducing the risk of virus transmission, it is important to understand if a prolonged usage of the same face mask can have effectiveness on filtering capability and potential health consequences. To this aim, we present three investigations. A survey, carried out in central Italy, offers an overview of the distorted public awareness of face mask usage. A functional study shows how prolonged wearing leads to substantial drops in humid air filtration efficiency. Finally, a morphological analysis reports the proliferation of fungal or bacteria colonies inside an improperly used mask. Our study highlights therefore that wearing a face mask is really beneficial only if it is used correctly.

Compliant Nano-Pliers as a Biomedical Tool at the Nanoscale: Design, Simulation and Fabrication.

This paper presents the development of a multi-hinge, multi-DoF (Degrees of Freedom) nanogripper actuated by means of rotary comb drives and equipped with CSFH (Conjugate Surface Flexure Hinges), with the goal of performing complex in-plane movements at the nanoscale. The design approach, the simulation and a specifically conceived single-mask fabrication process are described in detail and the achieved results are illustrated by SEM images. The first prototype presents a total overall area of (550 × 550) µm2, an active clamping area of (2 × 4) µm2, 600 nm-wide circular curved beams as flexible hinges for its motion and an aspect ratio of about 2.5. These features allow the proposed system to grasp objects a few hundred nanometers in size.

Few-Electron Ultrastrong Light-Matter Coupling at 300 GHz with Nanogap Hybrid LC Microcavities.

Ultrastrong light-matter coupling allows the exploration of new states of matter through the interaction of strong vacuum fields with huge electronic dipoles. By using hybrid dipole antenna-split ring resonator-based cavities with extremely small effective mode volumes Veff/λ03 ≃ 6 × 10-10 and surfaces Seff/λ02 ≃ 3.5 × 10-7, we probe the ultrastrong light-matter coupling at 300 GHz to less than 100 electrons located in the last occupied Landau level of a high mobility two-dimensional electron gas, measuring a normalized coupling ratio of ΩR/ωc = 0.36. Effects of the extremely reduced cavity dimensions are observed as the light-matter coupled system is better described by an effective mass heavier than the uncoupled one. These results open the way to ultrastrong coupling at the single-electron level in two-dimensional electron systems.

Controlling DNA Bundle Size and Spatial Arrangement in Self-assembled Arrays on Superhydrophobic Surface.

The use of superhydrophobic surfaces (SHSs) is now emerging as an attractive platform for the realization of one-dimensional (1D) nanostructures with potential applications in many nanotechnological and biotechnological fields. To this purpose, a strict control of the nanostructures size and their spatial arrangement is highly required. However, these parameters may be strongly dependent on the complex evaporation dynamics of the sessile droplet on the SHS. In this work, we investigated the effect of the evaporation dynamics on the size and the spatial arrangement of self-assembled 1D DNA bundles. Our results reveal that different arrangements and bundle size distributions may occur depending on droplet evaporation stage. These results contribute to elucidate the formation mechanism of 1D nanostructures on SHSs.

Periodically structured X-ray waveguides.

The properties of X-ray vacuum-gap waveguides (WGs) with additional periodic structure on one of the reflecting walls are studied. Theoretical considerations, numerical simulations and experimental results confirm that the periodic structure imposes additional conditions on efficient propagation of the electromagnetic field along the WGs. The transmission is maximum for guided modes that possess sufficient phase synchronism with the periodic structure (here called `super-resonances'). The field inside the WGs is essentially given at low incidence angle by the fundamental mode strongly coupled with the corresponding phased-matched mode. Both the simulated and the experimental diffraction patterns show in the far field that propagation takes place essentially only for low incidence angles, confirming the mode filtering properties of the structured X-ray waveguides.

Reconstruction of the angle of shot by using computed radiography of the head.

In a case of murder by a single .22 caliber bullet fragmented in the head, determination of the trajectory was a key issue in identifying which of 2 windows, 1 of which was associated with 2 suspects, was the site of fire. For this purpose, we processed the computed tomography of the victim's head by using a radiation therapy planning system called Plato, which is routinely used in radiation oncology. This tool provided a 3-dimensional reconstruction of the cranio-cerebral lesions and a spatial location of bullet and bone fragments. In this article is described the more intuitive relationship with forensic and ballistic data obtained from the 3-dimensional visualization and the physical and mathematical analysis used to calculate the angle of shot.