RESUMO
Quantum effects in nanoscale electronic devices promise to lead to new types of functionality not achievable using classical electronic components. However, quantum behaviour also presents an unresolved challenge facing electronics at the few-nanometre scale: resistive channels start leaking owing to quantum tunnelling. This affects the performance of nanoscale transistors, with direct source-drain tunnelling degrading switching ratios and subthreshold swings, and ultimately limiting operating frequency due to increased static power dissipation. The usual strategy to mitigate quantum effects has been to increase device complexity, but theory shows that if quantum effects can be exploited in molecular-scale electronics, this could provide a route to lower energy consumption and boost device performance. Here we demonstrate these effects experimentally, showing how the performance of molecular transistors is improved when the resistive channel contains two destructively interfering waves. We use a zinc-porphyrin coupled to graphene electrodes in a three-terminal transistor to demonstrate a >104 conductance-switching ratio, a subthreshold swing at the thermionic limit, a >7 kHz operating frequency and stability over >105 cycles. We fully map the anti-resonance interference features in conductance, reproduce the behaviour by density functional theory calculations and trace back the high performance to the coupling between molecular orbitals and graphene edge states. These results demonstrate how the quantum nature of electron transmission at the nanoscale can enhance, rather than degrade, device performance, and highlight directions for future development of miniaturized electronics.
RESUMO
We report a combined experimental and theoretical study of a series of thiomethyl (SMe) anchored cross-conjugated molecules featuring an acyclic central bridging ketone and their analogous skipped-conjugated alcohol derivatives. Studies of these molecules in a gold|single-molecule|gold junction using scanning tunneling microscopy-break junction techniques reveal a similar conductance (G) value for both the cross-conjugated molecules and their skipped-conjugated partners. Theoretical studies based on density functional theory of the molecules in their optimum geometries in the junction reveal the reason for this similarity in conductance, as the predicted conductance for the alcohol series of compounds varies more with the tilt angle. Thermopower measurements reveal a higher Seebeck coefficient (S) for the cross-conjugated ketone molecules relative to the alcohol derivatives, with a particularly high S for the biphenyl derivative 3a (-15.6 µV/K), an increase of threefold compared to its alcohol analog. The predicted behavior of the quantum interference (QI) in this series of cross-conjugated molecules is found to be constructive, though the appearance of a destructive QI feature for 3a is due to the degeneracy of the HOMO orbital and may explain the enhancement of the value of S for this molecule.
RESUMO
Dialkynylferrocenes exhibit attractive electronic and rotational features that make them ideal candidates for use in molecular electronic applications. However previous works have primarily focussed on single-molecule studies, with limited opportunities to translate these features into devices. In this report, we utilise a variety of techniques to examine both the geometric and electronic structure of a range of 1,1'-dialkynylferrocene molecules, as either single-molecules, or as self-assembled monolayers. Previous single molecule studies have shown that similar molecules can adopt an 'open' conformation. However, in this work, DFT calculations, STM-BJ experiments and AFM imaging reveal that these molecules prefer to occupy a 'hairpin' conformation, where both alkynes point towards the metal surface. Interestingly we find that only one of the terminal anchor groups binds to the surface, though both the presence and nature of the second alkyne affect the thermoelectric properties of these systems. First, the secondary alkyne acts to affect the position of the frontier molecular orbitals, leading to increases in the Seebeck coefficient. Secondly, theoretical calculations suggested that rotating the secondary alkyne away from the surface acts to modulate thermoelectric properties. This work represents the first of its kind to examine the assembly of dialkynylferrocenes, providing valuable information about both their structure and electronic properties, as well as unveiling new ways in which both of these properties can be controlled.
RESUMO
[This corrects the article DOI: 10.1039/D0NA00772B.].
RESUMO
We report measurements on gold|single-molecule|gold junctions, using a modified scanning tunneling microscope-break junction (STM-BJ) technique, of the Seebeck coefficient and electrical conductance of a series of bridged biphenyl molecules, with meta connectivities to pyridyl anchor groups. These data are compared with a previously reported study of para-connected analogues. In agreement with a tight binding model, the electrical conductance of the meta series is relatively low and is sensitive to the nature of the bridging groups, whereas in the para case the conductance is higher and relatively insensitive to the presence of the bridging groups. This difference in sensitivity arises from the presence of destructive quantum interference in the π system of the unbridged aromatic core, which is alleviated to different degrees by the presence of bridging groups. More precisely, the Seebeck coefficient of meta-connected molecules was found to vary between -6.1 µV K-1 and -14.1 µV K-1, whereas that of the para-connected molecules varied from -5.5 µV K-1 and -9.0 µV K-1.
RESUMO
The realization of self-assembled molecular-electronic films, whose room-temperature transport properties are controlled by quantum interference (QI), is an essential step in the scale-up of QI effects from single molecules to parallel arrays of molecules. Recently, the effect of destructive QI (DQI) on the electrical conductance of self-assembled monolayers (SAMs) has been investigated. Here, through a combined experimental and theoretical investigation, we demonstrate chemical control of different forms of constructive QI (CQI) in cross-plane transport through SAMs and assess its influence on cross-plane thermoelectricity in SAMs. It is known that the electrical conductance of single molecules can be controlled in a deterministic manner, by chemically varying their connectivity to external electrodes. Here, by employing synthetic methodologies to vary the connectivity of terminal anchor groups around aromatic anthracene cores, and by forming SAMs of the resulting molecules, we clearly demonstrate that this signature of CQI can be translated into SAM-on-gold molecular films. We show that the conductance of vertical molecular junctions formed from anthracene-based molecules with two different connectivities differ by a factor of approximately 16, in agreement with theoretical predictions for their conductance ratio based on CQI effects within the core. We also demonstrate that for molecules with thioether anchor groups, the Seebeck coefficient of such films is connectivity dependent and with an appropriate choice of connectivity can be boosted by â¼50%. This demonstration of QI and its influence on thermoelectricity in SAMs represents a critical step toward functional ultra-thin-film devices for future thermoelectric and molecular-scale electronics applications.
RESUMO
To explore solvent gating of single-molecule electrical conductance due to solvent-molecule interactions, charge transport through single-molecule junctions with different anchoring groups in various solvent environments was measured by using the mechanically controllable break junction technique. We found that the conductance of single-molecule junctions can be tuned by nearly an order of magnitude by varying the polarity of solvent. Furthermore, gating efficiency due to solvent-molecule interactions was found to be dependent on the choice of the anchor group. Theoretical calculations revealed that the polar solvent shifted the molecular-orbital energies, based on the coupling strength of the anchor groups. For weakly coupled molecular junctions, the polar solvent-molecule interaction was observed to reduce the energy gap between the molecular orbital and the Fermi level of the electrode and shifted the molecular orbitals. This resulted in a more significant gating effect than that of the strongly coupled molecules. This study suggested that solvent-molecule interaction can significantly affect the charge transport through single-molecule junctions.
RESUMO
If the Seebeck coefficient of single molecules or self-assembled monolayers (SAMs) could be predicted from measurements of their conductance-voltage (G-V) characteristics alone, then the experimentally more difficult task of creating a set-up to measure their thermoelectric properties could be avoided. This article highlights a novel strategy for predicting an upper bound to the Seebeck coefficient of single molecules or SAMs, from measurements of their G-V characteristics. The theory begins by making a fit to measured G-V curves using three fitting parameters, denoted a, b, c. This 'ABC' theory then predicts a maximum value for the magnitude of the corresponding Seebeck coefficient. This is a useful material parameter, because if the predicted upper bound is large, then the material would warrant further investigation using a full Seebeck-measurement setup. On the other hand, if the upper bound is small, then the material would not be promising and this much more technically demanding set of measurements would be avoided. Histograms of predicted Seebeck coefficients are compared with histograms of measured Seebeck coefficients for six different SAMs, formed from anthracene-based molecules with different anchor groups and are shown to be in excellent agreement.
RESUMO
A key area of activity in contemporary molecular electronics is the chemical control of conductance of molecular junctions and devices. Here we study and modify a range of pyrrolodipyridines (carbazole-like) molecular wires. We are able to change the electrical conductance and quantum interference patterns by chemically regulating the bridging nitrogen atom in the tricyclic ring system. A series of eight different N-substituted pyrrolodipyridines has been synthesized and subjected to single-molecule electrical characterization using an STM break junction. Correlations of these experimental data with theoretical calculations underline the importance of the pyrrolic nitrogen in facilitating conductance across the molecular bridge and controlling quantum interference. The large chemical modulation for the meta-connected series is not apparent for the para-series, showing the competition between (i) meta-connectivity quantum interference phenomena and (ii) the ability of the pyrrolic nitrogen to facilitate conductance, that can be modulated by chemical substitution.
RESUMO
Charge transport is strongly suppressed by destructive quantum interference (DQI) in meta-connected 1,1'-biphenyl-containing molecules, resulting in low electrical conductance. Surprisingly, we have found that DQI is almost entirely overcome by adding a bridging carbonyl, to yield a cross-conjugated fluorenone. This contrasts with other π-systems, such as para-connected anthraquinone, where cross-conjugation results in low conductance.
RESUMO
Interference features in the transmission spectra can dominate charge transport in metal-molecule-metal junctions when they occur close to the contact Fermi energy (E F). Here, we show that by forming a charge-transfer complex with tetracyanoethylene (TCNE) we can introduce new constructive interference features in the transmission profile of electron-rich, thiophene-based molecular wires that almost coincide with E F. Complexation can result in a large enhancement of junction conductance, with very efficient charge transport even at relatively large molecular lengths. For instance, we report a conductance of 10-3 G 0 (â¼78 nS) for the â¼2 nm long α-quaterthiophene:TCNE complex, almost two orders of magnitude higher than the conductance of the bare molecular wire. As the conductance of the complexes is remarkably independent of features such as the molecular backbone and the nature of the contacts to the electrodes, our results strongly suggest that the interference features are consistently pinned near to the Fermi energy of the metallic leads. Theoretical studies indicate that the semi-occupied nature of the charge-transfer orbital is not only important in giving rise to the latter effect, but also could result in spin-dependent transport for the charge-transfer complexes. These results therefore present a simple yet effective way to increase charge transport efficiency in long and poorly conductive molecular wires, with important repercussions in single-entity thermoelectronics and spintronics.
RESUMO
Molecular transistors operating in the quantum tunneling regime represent potential electronic building blocks for future integrated circuits. However, due to their complex fabrication processes and poor stability, traditional molecular transistors can only operate stably at cryogenic temperatures. Here, through a combined experimental and theoretical investigation, we demonstrate a new design of vertical molecular tunneling transistors, with stable switching operations up to room temperature, formed from cross-plane graphene/self-assembled monolayer (SAM)/gold heterostructures. We show that vertical molecular junctions formed from pseudo-p-bis((4-(acetylthio)phenyl)ethynyl)-p-[2,2]cyclophane (PCP) SAMs exhibit destructive quantum interference (QI) effects, which are absent in 1,4-bis(((4-acetylthio)phenyl)ethynyl)benzene (OPE3) SAMs. Consequently, the zero-bias differential conductance of the former is only about 2% of the latter, resulting in an enhanced on-off current ratio for (PCP) SAMs. Field-effect control is achieved using an ionic liquid gate, whose strong vertical electric field penetrates through the graphene layer and tunes the energy levels of the SAMs. The resulting on-off current ratio achieved in PCP SAMs can reach up to ~330, about one order of magnitude higher than that of OPE3 SAMs. The demonstration of molecular junctions with combined QI effect and gate tunability represents a critical step toward functional devices in future molecular-scale electronics.
RESUMO
The functionalities offered by single-molecule electrical junctions are yet to be translated into monolayer or few-layer molecular films, where making effective and reproducible electrical contact is one of the challenging bottlenecks. Here we take a significant step in this direction by demonstrating that excellent electrical contact can be made with a monolayer biphenyl-4,4'-dithiol (BPDT) molecular film, sandwiched between gold and graphene electrodes. This sandwich device structure is advantageous, because the current flows through the molecules to the gold substrate in a 'cross-plane' manner, perpendicular to the plane of graphene, yielding high-conductance devices. We elucidate the nature of the cross-plane graphene/molecule/Au transport using quantum transport calculations and introduce a simple analytical model, which captures generic features of the current-voltage characteristic. Asymmetry in junction properties results from the disparity in electrode electrical properties, the alignment of the BPDT HOMO-LUMO energy levels and the specific characteristics of the graphene electrode. The experimental observation of scalability of junction properties within the junction area, in combination with a theoretical description of the transmission probability of the thiol-graphene contact, demonstrates that between 10% and 100% of the molecules make contact with the electrodes, which is several orders of magnitude greater than that achieved to date in the literature.
RESUMO
A key goal in molecular electronics has been to find molecules that facilitate efficient charge transport over long distances. Normally, molecular wires become less conductive with increasing length. Here, we report a series of fused porphyrin oligomers for which the conductance increases substantially with length by >10-fold at a bias of 0.7 V. This exceptional behavior can be attributed to the rapid decrease of the HOMO-LUMO gap with the length of fused porphyrins. In contrast, for butadiyne-linked porphyrin oligomers with moderate inter-ring coupling, a normal conductance decrease with length is found for all bias voltages explored (±1 V), although the attenuation factor (ß) decreases from ca. 2 nm-1 at low bias to <1 nm-1 at 0.9 V, highlighting that ß is not an intrinsic molecular property. Further theoretical analysis using density functional theory underlines the role of intersite coupling and indicates that this large increase in conductance with length at increasing voltages can be generalized to other molecular oligomers.
RESUMO
Electrical conductance across a molecular junction is strongly determined by the anchoring group of the molecule. Here we highlight the unusual behavior of 1,4-bis(1H-pyrazol-4-ylethynyl)benzene that exhibits unconventional junction current versus junction-stretching distance curves, which are peak-shaped and feature two conducting states of 2.3 × 10-4 G0 and 3.4 × 10-4 G0. A combination of theory and experiments is used to understand the conductance of single-molecule junctions featuring this new anchoring group, i.e., pyrazolyl. These results demonstrate that the pyrazolyl moiety changes its protonation state and contact binding during junction evolution and that it also binds in either end-on or facial geometries with gold contacts. The pyrazolyl moiety holds general interest as a contacting group, because this linkage leads to a strong double anchoring of the molecule to the gold electrode, resulting in enhanced conductance values.
RESUMO
Correction for 'Connectivity dependence of Fano resonances in single molecules' by Ali K. Ismael et al., Phys. Chem. Chem. Phys., 2017, 19, 6416-6421.
RESUMO
If the factors controlling the decay in single-molecule electrical conductance G with molecular length L could be understood and controlled, then this would be a significant step forward in the design of high-conductance molecular wires. For a wide variety of molecules conducting by phase coherent tunnelling, conductance G decays with length following the relationship G = Ae-ßL. It is widely accepted that the attenuation coefficient ß is determined by the position of the Fermi energy of the electrodes relative to the energy of frontier orbitals of the molecular bridge, whereas the terminal anchor groups which bind to the molecule to the electrodes contribute to the pre-exponential factor A. We examine this premise for several series of molecules which contain a central conjugated moiety (phenyl, viologen or α-terthiophene) connected on either side to alkane chains of varying length, with each end terminated by thiol or thiomethyl anchor groups. In contrast with this expectation, we demonstrate both experimentally and theoretically that additional electronic states located on thiol anchor groups can significantly decrease the value of ß, by giving rise to resonances close to EF through coupling to the bridge moiety. This interplay between the gateway states and their coupling to a central conjugated moiety in the molecular bridges creates a new design strategy for realising higher-transmission molecular wires by taking advantage of the electrode-molecule interface properties.
RESUMO
When a linear aromatic molecule within a nanogap is bound only to a source electrode, and an adjacent molecule is bound only to a drain electrode, the two molecules can interact via pi-pi stacking, which allows electrons to flow from the source to the drain, via pi-pi bonds. Here we investigate the thermoelectric properties of such junctions, using mono-thiol oligo-phenylene ethynylene (OPE3)-based molecules as a model system. For molecules which are para-connected to the electrodes, we show that the Seebeck coefficient is an oscillatory function of the length L of the pi-pi overlap region and exhibits large positive and negative values. This bi-thermoelectric behavior is a result of quantum interference within the junction, which behaves like a molecular-scale Mach-Zehnder interferometer. For junctions formed from molecular monolayers sandwiched between planar electrodes, this allows both hole-like and electron-like Seebeck coefficients to be realized, by careful control of electrode separation On the other hand for meta-connected molecules, the Seebeck coefficient is insensitive to L, which may be helpful in designing resilient junctions with more stable and predictable thermoelectric properties.
RESUMO
We have employed the scanning tunneling microscope break-junction technique to investigate the single-molecule conductance of a family of 5,15-diaryl porphyrins bearing thioacetyl (SAc) or methylsulfide (SMe) binding groups at the ortho position of the phenyl rings (S2 compounds). These ortho substituents lead to two atropisomers, cis and trans, for each compound, which do not interconvert in solution under ambient conditions; even at high temperatures, isomerization takes several hours (half-life 15 h at 140 °C for SAc in C2Cl4D2). All the S2 compounds exhibit two conductance groups, and comparison with a monothiolated (S1) compound shows the higher group arises from a direct Au-porphyrin interaction. The lower conductance group is associated with the S-to-S pathway. When the binding group is SMe, the difference in junction length distribution reflects the difference in S-S distance (0.3 nm) between the two isomers. In the case of SAc, there are no significant differences between the plateau length distributions of the two isomers, and both show maximal stretching distances well exceeding their calculated junction lengths. Contact deformation accounts for part of the extra length, but the results indicate that cis-to-trans conversion takes place in the junction for the cis isomer. The barrier to atropisomerization is lower than the strength of the thiolate Au-S and Au-Au bonds, but higher than that of the Au-SMe bond, which explains why the strain in the junction only induces isomerization in the SAc compound.
RESUMO
As the field of unimolecular electronics develops, there is growing interest in the development of functionalised molecular wires, such as switches, which will allow for more complex molecular-scale circuits. To this end, a three redox state single molecule switch, 1, based on bis(pyrrolo)tetrathiafulvalene (BPTTF) has been designed, synthesised and investigated using scanning tunnelling microscopy break junction (STM-BJ) studies and quantum transport calculations. Oxidising the BPTTF unit increases its conjugation, which was anticipated to increase the molecular conductance of 1. By changing the redox state of 1 electrochemically it was possible to vary the single molecule conductance by more than an order of magnitude (from 10-5.2G0 to 10-3.8G0). Simulations afforded a qualitatively similar trend. An additional, higher conductance feature is present in most traces at junction sizes of around 2.0 nm - further extension affords the switchable lower conductance feature at junction sizes closer to the molecular length (ca. 3.0 nm). Analysis of the conductance traces shows that these two conductance features occur sequentially in nearly all junctions. This behaviour is attributed to an alternative initial junction conformation in which one or more of the BPTTF sulfur atoms acts as an anchoring group. This hypothesis is supported by a computational study of binding conformations and STM-BJ studies on a model compound, 2, with only one thiol anchor. Our results indicate that the redox properties of BPTTF make it an excellent candidate for use in single molecule switches.