Mechanism of the Wake-Up and the Split-Up in AlOx/Hf0.5Zr0.5Ox Film.

Dielectric layers are widely used in ferroelectric applications such as memory and negative capacitance devices. The wake-up and the split-up phenomena in the ferroelectric hafnia are well-known challenges in early-stage device reliability. We found that the phenomena even occur in the bilayer, which is composed of the hafnia and the dielectrics. The phenomena are known to be affected mainly by oxygen vacancies of hafnia. Dielectric layers, which are often metal oxides, are also prone to be affected by oxygen vacancies. To study the effect of the dielectric layer on the wake-up and the split-up phenomena, we fabricated ferroelectric thin-film capacitors with dielectric layers of various thicknesses and measured their field-cycling behaviors. We found that the movement of oxygen vacancies in the dielectric layer was predominantly affected by the polarization state of the ferroelectric layer. In addition, the mechanism of the field-cycling behavior in the bilayer is similar to that in ferroelectric thin films. Our results can be applied in ferroelectric applications that use dielectric layers.

Progressive and Stable Synaptic Plasticity with Femtojoule Energy Consumption by the Interface Engineering of a Metal/Ferroelectric/Semiconductor.

In the era of "big data," the cognitive system of the human brain is being mimicked through hardware implementation of highly accurate neuromorphic computing by progressive weight update in synaptic electronics. Low-energy synaptic operation requires both low reading current and short operation time to be applicable to large-scale neuromorphic computing systems. In this study, an energy-efficient synaptic device is implemented comprising a Ni/Pb(Zr0.52 Ti0.48 )O3 (PZT)/0.5 wt.% Nb-doped SrTiO3 (Nb:STO) heterojunction with a low reading current of 10 nA and short operation time of 20-100 ns. Ultralow femtojoule operation below 9 fJ at a synaptic event, which is comparable to the energy required for synaptic events in the human brain (10 fJ), is achieved by adjusting the Schottky barrier between the top electrode and ferroelectric film. Moreover, progressive domain switching in ferroelectric PZT successfully induces both low nonlinearity/asymmetry and good stability of the weight update. The synaptic device developed here can facilitate the development of large-scale neuromorphic arrays for artificial neural networks with low energy consumption and high accuracy.

Highly stable, solution-processed quaternary oxide thin film-based resistive switching random access memory devices via global and local stoichiometric manipulation strategy.

Optimization and performance enhancement of a low-cost, solution-processed InGaZnO (IGZO) resistance random access memory (ReRAM) device using the manipulation of global and local oxygen vacancy (Vo) stoichiometry in metal oxide thin films was demonstrated. Control of the overall Ga composition within the IGZO thin film reduced the excessive formation of oxygen vacancies allowing for a reproducible resistance switching mechanism. Furthermore, sophisticated local control of stoichiometric Vo is achieved using a 5 nm Ni layer at the IGZO interface to serve as an oxygen capturing layer through the formation of NiOx, consequently facilitating the formation of conductive filaments (CFs) and preventing abrupt degradation of device performance. Additionally, reducing the cell dimension of the IGZO-based ReRAMs using a cross-bar electrode structure appeared to drastically improve their performances parameters, including operating voltage and resistance distribution due to the suppression of excessive CFs formation. The optimized ReRAM devices exhibited stable unipolar resistive switching behavior with an endurance of >200 cycles, a retention time of 104 s at 85 °C and an on/off ratio greater than about 102. Therefore, our findings address the demand for low-cost memory devices with high stability and endurance for next-generation data storage technology.

Electrical manipulation of nanofilaments in transition-metal oxides for resistance-based memory.

The fabrication of controlled nanostructures such as quantum dots, nanotubes, nanowires, and nanopillars has progressed rapidly over the past 10 years. However, both bottom-up and top-down methods to integrate the nanostructures are met with several challenges. For practical applications with the high level of the integration, an approach that can fabricate the required structures locally is desirable. In addition, the electrical signal to construct and control the nanostructures can provide significant advantages toward the stability and ordering. Through experiments on the negative resistance switching phenomenon in Pt-NiO-Pt structures, we have fabricated nanofilament channels that can be electrically connected or disconnected. Various analyses indicate that the nanofilaments are made of nickel and are formed at the grain boundaries. The scaling behaviors of the nickel nanofilaments were closely examined, with respect to the switching time, power, and resistance. In particular, the 100 nm x 100 nm cell was switchable on the nanosecond scale, making them ideal for the basis for high-speed, high-density, nonvolatile memory applications.

Mobility enhanced photoactivity in sol-gel grown epitaxial anatase TiO2 films.

Epitaxial anatase thin films were grown on single-crystal LaAlO3 substrates by a sol-gel process. The epitaxial relationship between TiO2 and LaAlO3 was found to be [100]TiO2||[100]LaAlO3 and (001)TiO2||(001)LaAlO3 based on X-ray diffraction and a high-resolution transmission electron microscopy. The epitaxial anatase films show significantly improved photocatalytic properties, compared with polycrystalline anatase film on fused silica substrate. The increase in the photocatalytic activity of epitaxial anatase films is explained by enhanced charge carrier mobility, which is traced to the decreased grain boundary density in the epitaxial anatase film.