RESUMO
OBJECTIVES: The objective of this in vitro study was to assess the efficiency of incorporating Biosilicate particles (30 and 50 mg) into an experimental orodispersible film and its efficacy in the remineralization process of bovine dental enamel under cariogenic and erosive challenges. METHODS: Ninety-nine intact incisors, devoid of cracks or fractures, yielding 198 samples (6 × 6 × 2 mm) via vestibular sectioning using a low-speed diamond disc under water cooling. After flattening the enamel surface with 600, 1200, and 2000 grit sandpaper, the samples were divided into two groups based on the challenges they underwent: cariogenic (0.1 M lactic acid at pH 5.0) or erosive (0.05 M citric acid solution at pH 2.3). Samples from each challenge were further categorized into 11 groups (n = 9) according to the duration of cariogenic (3, 7, and 14 days) or erosive (3, 7, and 10 days) challenge, along with positive control groups (fragments untreated with challenges and treated with different Biosilicate concentrations) and negative controls (fragments treated with artificial saliva for the same periods established for cariogenic and erosive challenges). Treatments with orodispersible films containing Biosilicate (30 and 50 mg) were administered for 2 min per day for 15 days. RESULTS: The highest remineralizing potential was observed in samples treated with Biosilicate after 14 days of cariogenic challenge, irrespective of the concentration tested. For samples subjected to erosive challenge, erosion time did not affect Biosilicate's remineralizing potential. CONCLUSION: Biosilicate shows promise in terms of remineralizing potential in enamel subjected to cariogenic challenge due to its ability to form hydroxycarbonapatite in mineralized tissues.
Assuntos
Cárie Dentária , Esmalte Dentário , Remineralização Dentária , Esmalte Dentário/efeitos dos fármacos , Esmalte Dentário/metabolismo , Animais , Bovinos , Cárie Dentária/metabolismo , Erosão DentáriaRESUMO
OBJECTIVE: This study evaluated the effect of bromelain and propolis extract on the bond strength (BS) of a universal adhesive system to eroded dentin. MATERIALS AND METHODS: Sixty human molars with exposed dentin were halved, with one half protected by composite resin and the other subjected to erosive treatment followed by remineralization. After the erosive treatment, the composite resin was removed, and the teeth were randomly assigned to three groups (n = 20): Adhesive-Control System; Br-10%; Pr-16%. Following the treatments, composite resin blocks were built on the dentin surfaces and sticks of 0.9 mm2 were obtained and stored in distilled water at 37°C for 24 h and 6 months. After these periods, the sticks underwent bond strength testing and the data were analyzed using 2-way ANOVA, Bonferroni test, p < 0.05. Fracture patterns were observed using light microscope and scanning electron microscopy. RESULTS: Irrespective of the substrate and aging duration, propolis demonstrated higher BS (p < 0.05) compared to the other treatments. Eroded dentin exhibited greater removal of the smear layer and dentinal tubules with a larger diameter than sound dentin, especially when treated with bromelain, resulting in the formation of resin tags. CONCLUSIONS: Propolis consistently promoted the highest bond strength, irrespective of aging or substrate. Eroded dentin treated with propolis, or bromelain exhibited a higher prevalence of non-adhesive fractures and resin tag formation. CLINICAL SIGNIFICANCE: Propolis shows promise for enhancing the longevity of adhesive restorations in eroded dentin due to its ability to promote high bond strength.
Assuntos
Colagem Dentária , Própole , Humanos , Bromelaínas , Adesivos Dentinários/química , Cimentos de Resina/química , Própole/farmacologia , Dentina , Resinas Compostas/química , Resistência à Tração , Teste de MateriaisRESUMO
PURPOSE: This study aimed to assess and compare the color stability, flexural strength (FS), and surface roughness of occlusal splints fabricated from heat-cured acrylic resin, milled polymethyl methacrylate (PMMA)-based resin, and 3D-printed (PMMA) based-resin. MATERIALS AND METHODS: Samples of each type of resin were obtained, and baseline measurements of color and surface roughness were recorded. The specimens were divided into three groups (n = 10) and subjected to distinct aging protocols: thermomechanical cycling (TMC), simulated brushing (SB), and control (without aging). Final assessments of color and surface roughness and three-point bending test (ODM100; Odeme) were conducted, and data were statistically analyzed (2-way ANOVA, Tukey, P <.05). RESULTS: Across all resin types, the most significant increase in surface roughness (Ra) was observed after TMC (P < .05), with the 3D-printed resin exhibiting the lowest Ra (P < .05). After brushing, milled resin displayed the highest Ra (P < .05) and greater color alteration (ΔE00) compared to 3D-printed resin. The most substantial ΔE00 was recorded after brushing for all resins, except for heat-cured resin subjected to TMC. Regardless of aging, milled resin exhibited the highest FS (P < .05), except when compared to 3D-printed resin subjected to TMC. Heat-cured resin exposed to TMC demonstrated the lowest FS, different (P < .05) from the control. Under control conditions, milled resin exhibited the highest FS, different (P < .05) from the brushed group. 3D-printed resin subjected to TMC displayed the highest FS (P < .05). CONCLUSION: Among the tested resins, 3D-printed resin demonstrated superior longevity, characterized by minimal surface roughness and color alterations. Aging had a negligible impact on its mechanical properties.
RESUMO
RESUMO Este artigo investiga o perfil de uso inadequado em serviços de saúde pública no Brasil, através da análise das características do usuário e das circunstâncias de atendimento de usuários de call centers. São utilizadas informações de centrais de aconselhamento médico por telefone. Um modelo de regressão logística binária é proposto para estimar as relações entre o perfil do usuário, as circunstâncias de atendimento e a demanda inadequada. Impactaram significativamente para a probabilidade de demanda inadequada a maior complexidade da intenção inicial do usuário e o uso do sistema de serviço de saúde nas horas finais do dia.
ABSTRACT This article investigates the profile of inappropriate use in public health services in Brazil, through the analysis of user's characteristics and customer service circumstances of call centers. Information from telephone medical advice centers is used. A binary logistic regression model is proposed to estimate the relationships between the user profile, the service circumstances and the inadequate demand. The greater complexity of the user's initial intention and the use of the health service system in the final hours of the day were significantly impacted by the probability of inadequate demand.