Selective isolation and sensitive detection of lysozyme using aptamer based magnetic adsorbent and a new quartz crystal microbalance system.

Magnetic chitosan beads and quartz crystal microbalance chip were decorated with lysozyme specific aptamer for isolation and detection of lysozyme, respectively. The lysozyme specific aptamer was immobilized on poly (dopamine) coated magnetic chitosan beads and the chip via Schiff base reaction. The percentage of the removal efficiency and purity of the isolated lysozyme from egg white were 87.6% and 91.8%, respectively. Further, the sensor system was contacted with different concentrations of lysozyme and other test proteins. This sensor system provided a method for the label-free, concentration-dependent, and selective detection of lysozyme with an observed detection limit of 17.9 ± 0.6 ng/mL. The sensor system was very selective and not significantly responded to the other tested proteins such as ovalbumin, trypsin, cytochrome C, and glucose oxidase. The prepared new sensor system showed a good durability and a high sensitivity for determination of lysozyme from solutions and whole egg white.

Immobilization of Candida rugosa lipase on magnetic chitosan beads and application in flavor esters synthesis.

In this work, magnetic chitosan (MCH) beads were synthesized by phase-inversion method, and grafted with polydopamine (PDA) and then used for direct immobilization of Candida rugosa lipase by Schiff base reaction. The amount of immobilized enzyme and the retained activity were found to be 47.3 mg/g and 72.8%, respectively, at pH 7.0, and at 25 °C. The apparent Km (9.7 mmol/L), and Vmax (384 U/mg) values of the immobilized lipase were significantly changed compared to the free lipase. The MCH@PDA-lipase was better thermal and storage stability at different temperatures than those of the free lipase. In hexane medium, the esterification reaction results showed that the maximum conversions of isoamylalcohol and isopentyl alcohol to isoamyl acetate and isopentyl acetate using the MCH@PDA-lipase were found to be 98.4 ± 1.3% and 73.7 ± 0.7%, respectively. These results showed that the MCH@PDA-lipase can be used as an operative immobilized enzyme system for many biotechnological applications.

Strong and weak cation-exchange groups generated cryogels films for adsorption and purification of lysozyme from chicken egg white.

Here, the macroporous poly(hydroxylmethyl methacrylate/glycidyl methacrylate [p(HEMA-GMA)] cryogels with large porous surface were prepared, and then the epoxy groups of the p(HEMA-GMA) cryogels were systematically modified into strong and weak cationic groups. The effects of initial protein concentrations, adsorption time, pH, salt concentrations and temperatures on adsorption efficiency of cation exchange cryogels for lysozyme were determined. The maximum lysozyme adsorption capacities of strong and weak cation exchange cryogels were found to be 188.3 and 79.7 mg/g cryogel at 25 °C, respectively. The performance of the strong cationic cryogel was evaluated by purification of lysozyme from egg white. The activity of the isolated lysozyme was found to be 21,347 U/mg. The cationic cryogel maintained its expected high adsorption capacity and efficiency of the purification levels during repeated adsorption desorption processes. Finally, the purpose of this work is the design a cation exchange system for purification of lysozyme from egg-white.

P(HPMA/EGDMA) beads grafted with fibrous chains by SI-ATRP method: agmatine functionalized affinity beads for selective separation of serum albumin.

In this paper, novel core-shell polymeric affinity beads based on fibrous grafting and functionalization with a salt resistance affinity ligand were developed to separate and deplete serum albumin (SA) from human serum. Poly(hydroxypropyl methacrylate/ethyleneglycole dimethacrylate), p(HPMA/EGDMA), beads were prepared via suspension polymerization, and were grafted with poly(glycidyl methacrylate) (p(GMA)) via surface-initiated atom transfer radical polymerization (SI-ATRP) method. The grafted p(GMA) fibrous chains on the beads were modified with an affinity ligand (i.e., agmatine). The binding capacity of the affinity beads to SA was determined using aqueous solution of SA in a batch system. Batch adsorption studies showed that the amount of adsorbed SA was found to be 156.7 mg/g at 25 °C. The maximum adsorption capacity for affinity beads was observed at around pH 5.5. Adsorption of SA onto affinity beads significantly increased with increasing temperature, and reached a value 177.8 mg/g beads at 35 °C. The equilibrium data were found to be well described by Langmuir model, while the kinetic data were well fitted to the pseudo-second-order kinetic. The degree of the purity of SA was determined by using HPLC. Before and after adsorption, the peak areas of SA were used in the calculation of separated SA.

Cross-linking of horseradish peroxidase adsorbed on polycationic films: utilization for direct dye degradation.

Horseradish peroxidase (HRP) was immobilized on the polyaniline (PANI) grafted polyacrylonitrile (PAN) films. The maximum HRP immobilization capacity of the PAN-g-PANI-3 film was 221 µg/cm(2). The HRP-immobilized PAN-g-PANI-3 film retained 79 % of the activity of the same quantity free enzyme. The HRP-immobilized PAN-g-PANI-3 film was operated for the decolorization of two different benzidine-based dyes in the presence of hydrogen peroxide. The maximum decolorization grade was obtained at pH 6.0 for both dyes. The HRP-immobilized PAN-g-PANI-3 film was very effective for removal of Direct Blue-53 compared to Direct Black-38 from aqueous solutions. The immobilized HRP exhibited high resistance to proteolysis by trypsin compared to the free counterpart. Immobilized HRP preserved 83 % of its original activity even after 8 weeks of storage at 4 °C, while the free enzyme lost its initial activity after 3 weeks of storage period.

Development of a sensitive method for selection of affinity ligand for trypsin using quartz crystal microbalance sensor.

In this work, a new methodology is developed for selection of affinity ligands towards the enzyme "trypsin" using quartz crystals microbalance (QCM) technique. To achieve this goal, the surface amination of gold plated QCM crystals was achieved in 13.56 MHz plasma polymerization system by using ethylenediamine. Three different ligands (i.e., 4-aminobenzamidine, 4-aminobenzoic acid, and phenylalanine) were immobilized on the aminated QCM crystals surface via glutaraldehyde coupling. All three ligand immobilized QCM crystals were characterized and compared under different experimental conditions. It was observed that the benzamidine ligand showed higher affinity to trypsin with a dissociation constant on the order of 1.76 × 10(-9) M, which is within the range of 10(-4)-10(-8) M for affinity ligands. Thus, its selectivity was suitable for purification of trypsin from biological fluids.

Preparation and characterization of epoxy-functionalized magnetic chitosan beads: laccase immobilized for degradation of reactive dyes.

Cross-linked magnetic chitosan beads were prepared by phase-inversion technique in the presence of epichlorohydrin under alkaline condition, and used for covalent immobilization of laccase. The activity of the immobilized laccase on the magnetic chitosan was about 260 U (g/dry beads) with an enzyme loading of about 16.33 +/- 0.39 mg [(g/dry beads) mg/g]. Kinetic parameters, V (max) and K (m) values were determined as 21.7 U/mg protein and 9.4 microM for free enzyme, and 15.6 U/mg protein and 19.7 microM for the immobilized laccase, respectively. The operational and thermal stabilities of the immobilized laccase were improved compared to free counterpart. The immobilized laccase was operated in a batch reactor for the decolorization of reactive dyes from aqueous solution. The laccase immobilized on magnetic chitosan beads was very effective for removal of textile dyes from aqueous solution which creates an important environmental problem in the discharged textile dying solutions.

Reversible immobilization of Candida rugosa lipase on fibrous polymer grafted and sulfonated p(HEMA/EGDMA) beads.

Poly(2-hydroxyethyl methacrylate/ethylenglycol dimethacrylate) beads were grafted with poly(glycidylmethacrylate) via surface initiated atom transfer radical polymerization. Epoxy groups of the grafted polymer were modified in to sulfone groups. Sulfonated beads were characterized by swelling studies, FT-IR, SEM and elemental analysis, and were used for reversible immobilization of lipase. Under given experimental conditions, the beads had an adsorption capacity of 44.7 mg protein/g beads. The adsorbed lipase on beads retained up to 67.4% of its initial activity. The immobilized lipase exhibited improved thermal and storage stabilities over those of the free enzyme. The immobilized lipase could desorb 1.0 M NaCl solution at pH 8.0, and the sulfonated beads can be repeatedly charged with fresh enzyme after inactivation upon use.

Construction a hybrid biosorbent using Scenedesmus quadricauda and Ca-alginate for biosorption of Cu(II), Zn(II) and Ni(II): kinetics and equilibrium studies.

The potential use of the immobilized fresh water algae (in Ca-alginate) of Scenedesmus quadricauda to remove Cu(II), Zn(II) and Ni(II) ions from aqueous solutions was evaluated using Ca-alginate beads as a control system. Ca-alginate beads containing immobilized algae were incubated for the uniform growth at 22 degrees C for 5d ays. Adsorption of Cu(II), Zn(II) and Ni(II) ions on the immobilized algae showed highest values at around pH 5.0. Adsorption of Cu(II), Zn(II) and Ni(II) ions on the immobilized algae increased as the initial concentration of metal ions increased in the medium. The maximum adsorption capacities of the immobilized algal biosorbents for Cu(II), Zn(II) and Ni(II) were 75.6, 55.2 and 30.4 mg/g (or 1.155, 0.933 and 0.465 mmol/g) biosorbent, respectively. When the heavy metal ions were in competition, the amounts of adsorbed metal ions were found to be 0.84 mol/g for Cu(II), 0.59 mol/g for Ni(II) and 0.08 mol/g for Zn(II), the immobilised algal biomass was significantly selective for Cu(II) ions. The adsorption-equilibrium was also represented with Langmuir, Freundlich and Dubinin-Radushkevich adsorption isotherms. The adsorption of Cu(II), Zn(II) and Ni(II) ions on the immobilized algae followed second-order kinetic.

Biosorption of benzidine based textile dyes "Direct Blue 1 and Direct Red 128" using native and heat-treated biomass of Trametes versicolor.

The capacities and mechanisms of native and heat-treated white rot fungus "Trametes versicolor" biomass in removing of two different benzidine based dyes (i.e., Direct Blue 1, DB-1 and Direct Red 128, DR-128) from aqueous solution was investigated with different parameters, such as molecular weight of dye, adsorbent dosage, pH, temperature and ionic strength. In the batch system, the biosorption equilibrium time for both dyes was about 6h. The maximum biosorption was observed at pH 6.0 for DB-1 and at pH 3.0 for DR-128 on the native and heat-treated fungal biomass. The biosorption capacities of the native and heat-treated fungal biomass (at 800 mg/L dye concentration) were found to be 101.1 and 152.3 mg/g for DB-1 and these were 189.7 and 225.4 mg dye/g biomass for DR-128, respectively. The Freundlih and Temkin adsorption isotherm models were used for the mathematical description of the biosorption equilibrium. The Freundlich and Temkin models were able to describe the biosorption equilibrium of DB-l and DR-128 on the native and heat-treated fungal preparations. The Freundlich model also showed that the small molecular weight dye (i.e., DR-128) had a higher affinity of adsorption that than of the higher molecular weight dye (i.e., DB-1). The dye biosorption on the fungal biomass preparations followed the second order kinetics model.

Surface energy components of a dye-ligand immobilized pHEMA membranes: effects of their molecular attracting forces for non-covalent interactions with IgG and HSA in aqueous media.

In the present paper, we report the study of the adsorption behaviour of human immunoglobulin G (IgG), human serum albumin (HSA) and polyethylenimine (PEI) onto surfaces of Procion Green HE-4BD (PG) immobilized poly(hydroxyethylmethacrylate) (pHEMA) membranes. The adsorption behaviour of the IgG and HSA onto surfaces of the PG-PEI complexed membrane was also studied. Surface wettability and hydrophilicity of all the membranes were investigated by static contact angle measurements. The measurements of the contact angle to various test liquids, i.e., water, glycerol, formamide, diiodomethane (DIM) and ethylene glycol on the investigated membranes were made by sessile drop method. In accordance to the Young equation, the smaller the surface tension of the test liquid, the smaller becomes the contact angles measured on all the investigated membranes surfaces. The highest contact angles were obtained with water, whereas ethylene glycol gave the lowest contact angles for all the tested membranes. Component and parameters of the surface free energy of all the investigated membranes were calculated from measured contact angle values using two methods (the geometric mean by Fowkes and acid-base by van Oss). HSA adsorption was enhanced after complexation of PEI with the immobilized dye-ligand. The adsorption of proteins and PEI significantly changed both the contact angles and component of surface free energies of the investigated membranes.

Novel hydrophobic ligand-containing hydrogel membrane matrix: preparation and application to gamma-globulins adsorption.

In this study, phenylalanine as a hydrophobic ligand was covalently attached to the co-monomer methacrylochloride. Then, poly(2-hydroxyethylmethacrylate-co-methacrylamidophenyalanine) [poly(HEMA-MAPA)] membranes were prepared by UV-initiated photopolymerization of HEMA and methacrylamidophenyalanine. The gamma-globulins adsorption onto these affinity membranes from aqueous solutions containing different amounts of gamma-globulins at different pH was investigated in a batch system. The gamma-globulins adsorption capacity of the membranes was increased as the ligand density on the membrane surface increase. The non-specific adsorption of the gamma-globulins on the pHEMA membranes was negligible. The adsorption phenomena appeared to follow a typical Langmuir isotherm. The maximum adsorption capacity (q(m)) of the poly(HEMA-MAPA4) membrane for gamma-globulins was 2.37 mg g(-1) dry membrane. The equilibrium constant (k(d)) value was found to be 1.61x10(-1) mg ml(-1). More than 87% (up to 100%) of the adsorbed gamma-globulins were desorbed in 120 min in the desorption medium containing 50% ethylene glycol in 1.0 M NaCl.