Design of a Thermally Stable Heat-Resistant (Al2O3+Al3Ti)/Al Composite with Excellent High-Temperature Mechanical Properties: Multimechanism Synergistic Strengthening Strategy.

The effectiveness of the room-temperature strengthening strategy for aluminum (Al) is compromised at increased temperatures due to grain and precipitate phase coarsening. Overcoming the heightened activity of grain boundaries and dislocations poses a significant challenge in enhancing the high-temperature strength through traditional precipitation strengthening. This study presents novel strengthening strategies that integrate intergranular reinforcements, intragranular reinforcements, refined grain, and stacking faults within an (Al2O3+Al3Ti)/Al composite prepared using sol-gel and powder metallurgy technology. Excellent high-temperature tensile properties are achieved; also, a remarkable fatigue performance at increased temperatures that surpasses those of other existing Al alloys and composites is revealed. These superior characteristics can be attributed to its exceptionally stable microstructure and the synergistic strengthening mechanisms mentioned above. This work offers new insights into designing and fabricating thermally stable Al matrix composites for high-temperature applications.

Surface Reconstruction of La0.5Sr0.5CoO3-δ Ceramic toward High Solar Selectivity for High-Temperature Air-Stable Solar-Thermal Conversion.

As a key device for solar energy conversion, solar absorbers play a critical role in improving the operating temperature of concentrated solar power (CSP) systems. However, solar absorbers with high spectral selectivity and good thermal stability at high temperatures in air are still scarce. This study presents a novel surface reconstruction strategy to improve the spectral selectivity of La0.5Sr0.5CoO3-δ (LSC5) for enhanced CSP application. The strategy could efficiently enhance the solar absorptance due to the existence of a high-absorption thin layer composed of nanoparticles on the LSC5 surface. Meanwhile, the crystal facet with low emittance on the LSC5 surface was exposed. Thus, the LSC5 that underwent surface reconstruction achieved a higher solar absorptance (∼0.75) and lower infrared emittance (∼0.19) compared to the original LSC5 (0.63/0.21), representing an improvement of nearly 32%. Additionally, the surface reconstructed LSC5 demonstrated a lower infrared thermographic temperature and a higher solar-thermal conversion equilibrium temperature compared to those of LSC5 and SiC. Moreover, the reconstructed LSC5 could maintain stable performance up to 800 °C in air, which might simplify the complexity of the CSP systems. The surface reconstruction strategy provided a new method to optimize the spectral selectivity of high-temperature stable ceramics, contributing to advancements in solar energy conversion technologies.

A novel white Y2(Ti0.8Hf0.2)2O7: Eu phosphors regulated by HfO2 exhibiting low color shifting for high temperature.

The development of white phosphors that can be activated in near-ultraviolet light is highly important in the field of LED lighting. In this work, a series of color-tunable Y2(Ti1-xHfx)2O7:Eu phosphors were prepared by adjusting the HfO2 and Eu3+ concentrations. In particular, white Y2(Ti0.8Hf0.2)2O7:Eu phosphors were successfully synthesized and emitted a broad band covering the entire visible light region upon excitation with 340 nm UV light. The white banded materials were composed of Eu2+ and Eu3+ emissions and HfO2 defect emission. The formation of Eu2+ ions was caused by the introduction of HfO2, which causes self-reduction of Eu3+ ions but does not require additional reducing agents. The white Y2(Ti0.8Hf0.2)2O7:Eu phosphors exhibit low color shifting at high temperature, which is very important for LED applications. The chromaticity shift of the Y2(Ti0.8Hf0.2)2O7:0.2Eu phosphor is 2.83 × 10-2 at 503 K, which is only 54.8 % that of commercial three-color white phosphors at the same temperature. The Ra value did not decrease significantly with increasing temperature and reached 90.2 at 383 K. Y2 (Ti0.8Hf0.2)2O7:0.2Eu phosphors were assembled with a 365 nm LED chip to fabricate a WLED device that showed excellent white-colored coordinates (0.345, 0.358) and a high Ra value of 90.1 under a 300 mA current.

Broad bandwidth and excellent thermal stability in BiScO3-PbTiO3 high-temperature ultrasonic transducer for non-destructive testing.

High-temperature ultrasonic transducer (HTUT) is essential for non-destructive testing (NDT) in harsh environments. In this paper, a HTUT based on BiScO3-PbTiO3 (BS-PT) piezoelectric ceramics was developed, and the effect of different backing layers on its bandwidth were analyzed. The HTUT demonstrates a broad bandwidth and excellent thermal stability with operation temperature up to 400 °C. By using a 10 mm thick porous alumina backing layer, the HTUT achieves a broad -6 dB bandwidth of 100 %, which is about 4 times superior to the transducer with an air backing layer. The center frequency (fc) of the HTUT remains stable with fluctuations of less than 10 % across the temperature range from room temperature to 400 °C. The HTUT successfully detected simulated defects in pulse-echo mode for NDT over 200 °C. This research not only advances high-temperature ultrasonic transducer technology but also expands the NDT applications in harsh environmental conditions.

Mechanically activated self-propagating high-temperature synthesis of titanium silicide-molybdenum disilicide composite using constituent elements.

Silicides with potential to form a protective silica layer have garnered considerable attention as engineering ceramic materials. This research investigates the influence of initial composition and mechanical activation on the synthesis performance and microstructure of products in the Ti-Si-Mo system. Several compositions, including Ti8Mo29Si63, Ti15Mo25Si60, Ti22Mo22Si56, Ti40Mo12Si48, Ti52Mo6Si42, Ti62.5Si37.5, and Mo33Si67, were prepared and synthesized via mechanically activated self-propagating high-temperature synthesis (MASHS). XRD, SEM, and EDS analyses, along with related investigations such as grain size calculations and morphology studies, were performed. The results indicate that at low Ti concentrations, the composite contains (Ti0.8,Mo0.2)Si2 and MoSi2, whereas moderate Ti concentrations enable the formation of the MoSi2-Ti5Si3 composite. Moreover, a high amount of Mo can extensively dissolve into the titanium and titanium silicide structure, resulting in the synthesis of the (Ti,Mo)5Si3 phase in Ti-rich samples. The dissolution of Mo in the crystal structure of the compound decreases the lattice parameters of titanium silicide. Furthermore, mechanical activation facilitates the initiation of reactions in compositions with lower Ti content and yielding fine-grained products.

Impact of High-Temperature Feeds on Gut Microbiota and MAFLD.

The purpose of this study is to investigate the effects of non-obese MAFLD on the gut microbiota and metabolic pathways caused by high-temperature processed meals. It was decided to divide the eighteen male Sprague-Dawley rats into three groups: the control group, the dry-fried soybeans (DFS) group, and the high-fat diet (HFD) group. Following the passage of twelve weeks, a series of physical, biochemical, histological, and microbiological examinations were carried out. There were distinct pathological abnormalities brought about by each diet. The DFS diet was found to cause the development of fatty liver and to demonstrate strong relationships between components of the gut microbiota, such as Akkermansia and Mucispirillum, and indices of liver health. Diet-induced changes in the gut microbiome have a significant impact on liver pathology in non-obese patients with metabolically altered liver disease (MAFLD), which suggests that dietary interventions that target gut microbiota could be used to manage or prevent the illness.

Response Enhancement in High-Temperature H2S-Treated Metal Oxide Gas Sensors.

Metal oxide gas sensors (MOGS), crucial components in monitoring air quality and detecting hazardous gases, are well known for their poisoning effects when exposed to certain gas molecules, such as hydrogen sulfide. Surprisingly, our research reveals that high-temperature H2S treatment leads to an enhancement effect rather than response decay. This study investigates the time-decaying response enhancement, being attributed to the formation of metal sulfide and metal sulfate on the metal oxide's surface, enhancing the electronic sensitization. Such an enhancement effect is demonstrated for various gases, including CO, CH3CH2OH, CH4, HCHO, and NH3. Additionally, the impacts of H2S treatment on the response and recovery time are also observed. Surface compositional analysis are conducted with X-ray photoelectron spectroscopy. A proposed mechanism for the enhancement effect is elaborated, highlighting the role of electronic sensitization and the sulfide-sulfate component. This research offers valuable insights into the potential applications of metal oxide sensors in sulfide-presented harsh environments in gas sensing, encouraging future exploration of optimized sensor materials, operation temperature, and the development of hydrogen sulfide poisoning-resistant and higher sensitivity MOGS.

Enhancement of Mass Transport in Catalyst Layers of HT-PEMFC with Tetrafluorophenyl Phosphonic Acid Binder.

The design and development of new and efficient catalyst binder materials are important for improving cell performance in high-temperature proton-exchange membrane fuel cells (HT-PEMFCs). In this study, a series of tetrafluorophenyl phosphonic acid-based binder materials (PF-y-P, y = 1, 0.83, and 0.67) with rigid structures and controllable degrees of phosphonation were prepared and used in HT-PEMFCs using the ultra-strong acid-catalyzed Friedel-Crafts reaction and the combined Michaelis-Arbuzov reaction. The samples exhibited high stability, low water uptake, superior proton conductivity, and cell performance. In addition, the oxygen mass transport properties of the PF-1-P binder were investigated using high-temperature microelectrode electrochemical testing techniques. Compared with the phosphoric acid-doped polybenzimidazole (PBI) binder, the O2 solubility of PF-1-P binder material increased by 30% (5.36 × 10-6 mol cm-3) and the PF-1-P binder material exhibited better cell stability in HT-PEMFCs. After 10.5 h of discharge at a constant current of 0.12 A cm-2, the MEA voltage decreased by 7.1% and 20.8% in case of the PF-1-P and PBI binders, respectively.

Physiological responses contributing to multiple stress tolerance in Pichia kudriavzevii with potential enhancement for ethanol fermentation.

Economically feasible ethanol production requires efficient hydrolysis of lignocellulosic biomass and high-temperature processing to enable simultaneous saccharification and fermentation. During the lignocellulolysic hydrolysate, the yeast must encounter with a multiple of inhibitors such as heat and furfural. To solve this problem, a potential fermentative yeast strain that tolerated simultaneous multistress and enhance ethanol concentration was investigated. Twenty yeast isolates were classified into two major yeast species, namely Pichia kudriavzevii (twelve isolates) and Candida tropicalis (eight isolates). All P. kudriavzevii isolates were able to grow at high temperature (45 °C) and exhibited stress tolerance toward furfural. Among P. kudriavzevii isolates, NUCG-S3 presented the highest specific growth rate under each stress condition of heat and furfural, and multistress. Morphological changes in P. kudriavzevii isolates (NUCG-S2, NUCG-S3, NUKL-P1, NUKL-P3, and NUOR-J1) showed alteration in mean cell length and width compared to the non-stress condition. Ethanol production by glucose was also determined. The yeast strain, NUCG-S3, gave the highest ethanol concentrations at 99.46 ± 0.82, 62.23 ± 0.96, and 65.80 ± 0.62 g/l (P < 0.05) under temperature of 30 °C, 40 °C, and 42 °C, respectively. The tolerant isolated yeast NUCG-S3 achieved ethanol production of 53.58 ± 3.36 and 48.06 ± 3.31 g/l (P < 0.05) in the presence of 15 mM furfural and multistress (42 °C with 15 mM furfural), respectively. Based on the results of the present study, the novel thermos and furfural-tolerant yeast strain P. kudriavzevii NUCG-S3 showed promise as a highly proficient yeast for high-temperature ethanol fermentation.

SlWRKY55 coordinately acts with SlVQ11 to enhance tomato thermotolerance by activating SlHsfA2.

High temperature (HT) severely restricts plant growth, development, and productivity. Plants have evolved a set of mechanisms to cope with HT, including the regulation of heat stress transcription factors (Hsfs) and heat shock proteins (Hsps). However, it is not clear how the transcriptional and translational levels of Hsfs and Hsps are controlled in tomato. Here, we reported that the HT-induced transcription factor SlWRKY55 recruited SlVQ11 to coordinately regulate defense against HT. SlWRKY55 directly bound to the promoter of SlHsfA2 and promoted its expression, which was increased by SlVQ11. Moreover, both SlWRKY55 and SlVQ11 physically interacted with SlHsfA2 to enhance the transcriptional activity of SlHsfA2. Thus, our results revealed a molecular mechanism that the SlWRKY55/SlVQ11-SlHsfA2 cascade enhanced thermotolerance and provided potential target genes for improving the adaptability of crops to HT.

Engineering of LiTaO3 Nanoparticles by Flame Spray Pyrolysis: Understanding In Situ Li-Incorporation into the Ta2O5 Lattice.

Lithium tantalate (LiTaO3) perovskite finds wide use in pyroelectric detectors, optical waveguides and piezoelectric transducers, stemming from its good mechanical and chemical stability and optical transparency. Herein, we present a method for synthesis of LiTaO3 nanoparticles using a scalable Flame Spray Pyrolysis (FSP) technology, that allows the formation of LiTaO3 nanomaterials in a single step. Raman, XRD and TEM studies allow for comprehension of the formation mechanism of the LiTaO3 nanophases, with particular emphasis on the penetration of Li atoms into the Ta-oxide lattice. We show that, control of the High-Temperature Particle Residence Time (HTPRT) in the FSP flame, is the key-parameter that allows successful penetration of the -otherwise amorphous- Li phase into the Ta2O5 nanophase. In this way, via control of the HTPRT in the FSP process, we synthesized a series of nanostructured LiTaO3 particles of varying phase composition from {amorphous Li/Ta2O5/LiTaO3} to {pure LiTaO3, 15-25 nm}. Finally, the photophysical activity of the FSP-made LiTaO3 was validated for photocatalytic H2 production from H2O. These data are discussed in conjunction with the role of the phase composition of the LiTaO3 nanoparticles. More generally, the present work allows a better understanding of the mechanism of ABO3 perovskite formation that requires the incorporation of two cations, A and B, into the nanolattice.

Effect of Titanium Dioxide Particles on the Thermal Stability of Silica Aerogels.

Silica aerogels exhibit a unique nanostructure with low thermal conductivity and low density, making them attractive materials for thermal isolation under extreme conditions. The TiO2 particle is one of the common industrial additives used to reduce the thermal radiation of aerogel composites under high-temperature environments, but its influence on thermal resistance is almost unknown. Herein, we report the effect of TiO2 nanoparticles with different crystal phases and different sizes on the thermal stability of silica aerogel composites. By adding TiO2 nanoparticles, the aerogel can significantly resist collapse at high temperatures (up to 1000 °C). And compared with the rutile phase TiO2, the anatase phase TiO2 shows much higher temperature resistance performance, with shrinkage of only one-sixth of the rutile phase after 800 °C treatment. Interestingly, energy-dispersive spectrometer mapping results show that after 800 °C treatment, silica nanoparticles (NPs) are squeezed out in between anatase TiO2 particles, which resists the coarsening of silica NPs and ultimately enhances the stability of aerogel composites. The optimal anatase phase TiO2-doped silica aerogel demonstrates the integrated properties of crack-free morphology (2.84% shrinkage), low thermal conductivity (29.30 mW/(m·K)) and low density (149.4 mg/cm3) after 800 °C treatment. This study may provide new insights for developing oxide-doped silica aerogels with both high-temperature resistance and low thermal radiation.

Study on the influence of active oxygen on the natural oxidation of arsenopyrite under different temperature conditions.

Arsenic (As), a toxic element, contaminates farmlands, rivers, and groundwater, posing severe environmental and health risks. Notably, As-containing materials in tailings are affected by temperature variations during long-term storage, and this considerably impact the oxidation and migration of elements in arsenopyrite.This study focused on arsenopyrite and investigated the process of its oxidative dissolution and release of arsenic under different temperature conditions by using in-situ XRD, in-situ XPS and electron paramagnetic resonance spectroscopy(EPR), The role of oxygen free radicals in the oxidation of arsenopyrite was elucidated. It has been established that under high-temperature conditions As, iron (Fe), and sulfur (S) are primarily present As(V)/As(IV), Fe(III), and SO42-, respectively. The O2⋅- generated during the oxidation of As(III) by O2, OH⋅ produced by the Fe(II)/FeOH2+ reaction, and H2O2 formed via their interaction play a crucial role in the photochemical oxidation of arsenopyrite. These findings provide a theoretical basis for the formation of ferric arsenate precipitation, contributing in the adsorption and immobilisation of oxidatively released arsenic.

Room-Temperature, Solution-Processed, Robust, Transparent, and Conductive SiOx/AgNW Nanocomposite Coating.

AgNW networks show high promise as a conductive material due to excellent flexibility, low resistance, high transparency, and ease of large-scale preparation. However, the application of AgNW networks has been hindered by their inherent characteristics, such as easy oxidation degradation, chemical corrosion, and structural instability at high temperatures. In this study, a dense SiOx protective layer derived from perhydropolysilazane was introduced to fabricate a robust SiOx/AgNW nanocomposite coating through an all-solution process at room temperature. The achieved nanocomposite coating shows outstanding thermal stability up to 450 °C, resistance to ultraviolet radiation, and excellent mechanical performance by maintaining stability after 10,000 cycles of bending at a radius of 2.5 mm, 1000 cycles of peeling, and 1200 cycles of wearing. Meanwhile, the nanocomposite coating demonstrates exceptional chemical tolerance against HCl, Na2S, and organic solvents. A transparent heater based on the nanocomposite coating achieves a remarkable benchmark with a maximum temperature of 400 °C at 20 V. These features highlight the potential of the nanocomposite coating in flexible electronics, optoelectronics, touch screens, and high-performance heaters.

Surface Acoustic Wave Sensors for Wireless Temperature Measurements above 1200 Degree Celsius.

High-temperature wireless sensing is crucial for monitoring combustion chambers and turbine stators in aeroengines, where surface temperatures can reach up to 1200 °C. Surface Acoustic Wave (SAW) temperature sensors are an excellent choice for these measurements. However, at extreme temperatures, they face issues such as agglomeration and recrystallization of electrodes, leading to loss of conductivity and reduced quality factor, hindering effective wireless signal transmission. This study develops an LGS SAW sensor with a Pt-10%Rh/Zr/Pt-10%Rh/Zr/Pt-10%Rh/Zr multilayer composite electrode structure to address these challenges. We demonstrate that the sensor can achieve wireless temperature measurements from room temperature to 1200 °C with an accuracy of 1.59%. The composite electrodes excite a quasi-shear wave on the LGS substrate, maintaining a Q-factor of 3526 at room temperature, providing an initial assurance for the strength of the wireless interrogation echo signal. The sensor operates stably for 2.18 h at 1200 °C before adhesion loss between the composite electrode and the substrate causes a sudden increase in resonant frequency. This study highlights the durability of the proposed electrode materials and structure at extreme temperatures and suggests future research to improve adhesion and extend the sensor's lifespan, thereby enhancing the reliability and effectiveness of high-temperature wireless sensing in aerospace applications.

Advance in the Thermoinhibition of Lettuce (Lactuca sativa L.) Seed Germination.

Thermoinhibition refers to the inability of seeds to germinate when inhibited by high temperatures, but when environmental conditions return to normal, the seeds are able to germinate rapidly again, which is different from thermodormancy. Meanwhile, with global warming, the effect of the thermoinhibition phenomenon on the yield and quality of crops in agricultural production is becoming common. Lettuce, as a horticultural crop sensitive to high temperature, is particularly susceptible to the effects of thermoinhibition, resulting in yield reduction. Therefore, it is crucial to elucidate the intrinsic mechanism of action of thermoinhibition in lettuce seeds. This review mainly outlines several factors affecting thermoinhibition of lettuce seed germination, including endosperm hardening, alteration of endogenous or exogenous phytohormone concentrations, action of photosensitizing pigments, production and inhibition of metabolites, maternal effects, genetic expression, and other physical and chemical factors. Finally, we also discuss the challenges and potential of lettuce seed germination thermoinhibition research. The purpose of this study is to provide theoretical support for future research on lettuce seed germination thermoinhibition, and with the aim of revealing the mechanisms and effects behind lettuce seed thermoinhibition. This will enable the identification of more methods to alleviate seed thermoinhibition or the development of superior heat-tolerant lettuce seeds.

Effects of Heat Stress during Anthesis and Grain Filling Stages on Some Physiological and Agronomic Traits in Diverse Wheat Genotypes.

Heat stress represents a significant environmental challenge that adversely impacts the growth, physiology, and productivity of wheat. In order to determine the response to high temperatures of the wheat varieties developed mostly in the Pannonian environmental zone, as well as varietal differences, we subjected seven varieties from Serbia, one from Australia, and one from the UK to thermal stress during anthesis and mid-grain filling and combined stress during both of these periods. The changes in chlorophyll fluorescence and index, leaf temperature, and main agronomic traits of nine winter wheat varieties were investigated under high temperatures. Heat stress negatively affected leaf temperature, chlorophyll fluorescence, and the chlorophyll index during different growth stages. Compared to the control, stress at anthesis, mid-grain filling, and combined stress resulted in yield reductions of 32%, 46%, and 59%, respectively. Single treatment at anthesis had a more severe effect on the number of grains per plant, causing a 38% reduction compared to the control. Moreover, single treatment during mid-grain filling resulted in the greatest decline in grain weight, with a 29% reduction compared to the control. There was a significant varietal variation in heat tolerance, highlighting Avangarda and NS 40s as the most tolerant varieties that should be included in regular breeding programs as valuable sources of heat tolerance. Understanding the genetic and physiological mechanisms of heat tolerance in these promising varieties should be the primary focus of future research and help develop targeted breeding strategies and agronomic practices to mitigate the adverse effects of heat stress on wheat production.

Effect of High-Temperature Deformation Twinning on the Work Hardening Behavior of Fe-38Mn Alloy during Hot Shear-Compression Deformation.

The effect of high-temperature deformation twinning on the work hardening behaviors of Fe-38Mn alloy during hot shear-compression deformation was investigated. The discovery of micro-shear bands and deformation twinning is significant for continuous work hardening, and this represents an important step toward gaining a complete understanding of the effect of deformation twinning on work hardening behaviors. Deformation twinning is widely acknowledged to accommodate plastic strain under cold deformation, even under severe plastic deformation. At present, the equivalent stress vs. strain curves for hot shear-compression deformation of Fe-38Mn alloy exhibit the characteristics of continuous work hardening. In addition, continuous work hardening is classified into five stages when considering high-temperature deformation twinning.

Evaluation of the Effect of Mineral Oil Exposure on Changes in the Structure and Mechanical Properties of Polymer Parts Produced by Additive Manufacturing Techniques.

The paper describes the type of changes in the structure and mechanical properties of 3D printed shapes under the influence of mineral oil. The effects of a room (23 °C) and elevated temperature (70 °C) on 3D prints manufactured by the FDM method and stored in oil for 15, 30, and 60 days on the change of properties and structure were investigated. The samples were produced from ABS (poly(acrylonitrile-co-butadiene-co-styrene)), ASA (poly(acrylonitrile-co-styrene-co-acrylate), PLA (poly(lactic acid)), and HIPS (high-impact polystyrene). Tests related to the strength of the materials, such as the static tensile test and Charpy impact test, were carried out. The structure was evaluated using a scanning electron microscope, and changes in chemical structure were determined by conducting FTIR (Fourier transform infrared spectroscopy) and TGA (thermogravimetric analysis) tests. The analysis of the results provided important information about the impact of mineral oil on specific materials. This is critical for designing and manufacturing components that can withstand mineral oil exposure in real-world environments. The materials underwent varying changes. Strength increased for PLA by about 28%, remained unchanged for ABS and HIPS during exposure for 30 days, and decreased for ASA with extended exposure up to 14%.

Microstructures and High-Temperature Mechanical Properties of Inconel 718 Superalloy Fabricated via Laser Powder Bed Fusion.

The Inconel 718 superalloy demonstrates the potential to fabricate high-temperature components using additive manufacturing. However, additively manufactured Inconel 718 typically exhibits low strength, necessitating post-heat treatments for precipitate strengthening. This study investigated the microstructures and mechanical properties of the Inconel 718 superalloy fabricated via laser powder bed fusion. The room-temperature and high-temperature tensile properties of the Inconel 718 alloy samples following various post-heat treatments were evaluated. The results indicate that the as-built samples exhibited columnar grains with fine cell structures. Solution treatment resulted in δ phase formation and grain recrystallization. Subsequent double aging led to finely distributed nanoscale γ' and γ″ particles. These nanoscale particles provided high strength at both room and high temperatures, resulting in a balanced strength and ductility comparable to the wrought counterpart. High-temperature nanoindentation analyses revealed that the double-aging samples exhibited very high hardness and low creep rates at 650 °C.