Low temperature atomic layer deposition of cobalt using dicobalt hexacarbonyl-1-heptyne as precursor.

In this work, we present the development of an atomic layer deposition (ALD) process for metallic cobalt. The process operates at low temperatures using dicobalt hexacarbonyl-1-heptyne [Co2(CO)6HC≡CC5H11] and hydrogen plasma. For this precursor an ALD window in the temperature range between 50 and 110 °C was determined with a constant deposition rate of approximately 0.1 Å/cycle. The upper limit of the ALD window is defined by the onset of the decomposition of the precursor. In our case, decomposition occurs at temperatures of 125 °C and above, resulting in a film growth in chemical vapour deposition mode. The lower limit of the ALD window is around 35 °C, where the reduction of the precursor is incomplete. The saturation behaviour of the process was investigated. X-ray photoelectron spectroscopy measurements could show that the deposited cobalt is in the metallic state. The finally established process in ALD mode shows a homogeneous coating at the wafer level.

Plasma-Enhanced Atomic Layer Deposition of HfO2 with Substrate Biasing: Thin Films for High-Reflective Mirrors.

Tuning ion energies in plasma-enhanced atomic layer deposition (PEALD) processes enables fine control over the material properties of functional coatings. The growth, structural, mechanical, and optical properties of HfO2 thin films are presented in detail toward photonic applications. The influence of the film thickness and bias value on the properties of HfO2 thin films deposited at 100 °C using tetrakis(dimethylamino)hafnium (TDMAH) and oxygen plasma using substrate biasing is systematically analyzed. The HfO2 films deposited without a substrate bias show an amorphous microstructure with a low density, low refractive index, high incorporation of residual hydroxyl (OH) content, and high residual tensile stress. The material properties of HfO2 films significantly improved at a low bias voltage due to the interaction with oxygen ions accelerated to the film. Such HfO2 films have a higher density, higher refractive index, and lower residual OH incorporation than films without bias. The mechanical stress becomes compressive depending on the bias values. Further increasing the ion energies by applying a larger substrate bias results in a decrease of the film density, refractive index, and a higher residual OH incorporation as well as crystalline inclusions. The comparable material properties of the HfO2 films have been reported using tris(dimethylamino)cyclopentadienyl hafnium (TDMACpH) in a different apparatus, indicating that this approach can be transferred to various systems and is highly versatile. Finally, the substrate biasing technique has been introduced to deposit stress-compensated, crack- and delamination-free high-reflective (HR) mirrors at 355 and 532 nm wavelengths using HfO2 and SiO2 as high and low refractive index materials, respectively. Such mirrors could not be obtained without the substrate biasing during the deposition because of the high tensile stress of HfO2, leading to cracks in thick multilayer systems. An HR mirror for 532 nm wavelength shows a high reflectance of 99.93%, a residual transmittance of ∼530 ppm, and a low absorption of ∼11 ppm, as well as low scattering losses of ∼4 ppm, high laser-induced damage threshold, low mechanical stress, and high environmental stability.

Amorphous Alumina Film Robust under Cyclic Deformation: a Highly Impermeable and a Highly Flexible Encapsulation Material.

The lack of highly impermeable and highly flexible encapsulation materials is slowing the development of flexible organic solar cells. Here, a transparent and low-temperature synthetic alumina single layer is suggested as a highly impermeable and a highly flexible encapsulation material for organic solar cells. While the water vapor transmission rate (WVTR) is maintained up to 100,000 bending cycles for a 25 mm bending radius (corresponding to 8.1% of the elastic deformation limit), as measured by in situ tensile testing with free-standing 50 nm-thick alumina films, the WVTR degraded gradually depending on the bending radius and bending cycles for bending radii less than 25 mm. The degradation of the WVTR in cyclic deformation within the elastic deformation limit is investigated, and it is found to be due to the formation of pinholes by a bond-switching mechanism. Also, encapsulated organic solar cells with alumina films are found to maintain 80% of initial efficiency for 2 weeks even after cyclic bending with a 4 mm bending radius.

Low-Temperature As-Grown Crystalline ß-Ga2O3 Films via Plasma-Enhanced Atomic Layer Deposition.

We report on the low-temperature growth of crystalline Ga2O3 films on Si, sapphire, and glass substrates using plasma-enhanced atomic layer deposition (PEALD) featuring a hollow-cathode plasma source. Films were deposited by using triethylgallium (TEG) and Ar/O2 plasma as metal precursor and oxygen co-reactant, respectively. Growth experiments have been performed within 150-240 °C substrate temperature and 30-300 W radio-frequency (rf) plasma power ranges. Additionally, each unit AB-type ALD cycle was followed by an in situ Ar plasma annealing treatment, which consisted of an extra (50-300 W) Ar plasma exposure for 20 s ending just before the next TEG pulse. The growth per cycle (GPC) of the films without Ar plasma annealing step ranged between 0.69 and 1.31 Å/cycle, and as-grown refractive indices were between 1.67 and 1.75 within the scanned plasma power range. X-ray diffraction (XRD) measurements showed that Ga2O3 films grown without in situ Ar plasma annealing exhibited amorphous character irrespective of substrate temperature and rf power values. With the incorporation of the in situ Ar plasma annealing process, the GPC of Ga2O3 films ranged between 0.76 and 1.03 Å/cycle along with higher refractive index values of 1.75-1.79. The increased refractive index (1.79) and slightly reduced GPC (1.03 Å/cycle) at 250 W plasma annealing indicated possible densification and crystallization of the films. Indeed, X-ray measurements confirmed that in situ plasma annealed films grow in a monoclinic ß-Ga2O3 crystal phase. The film crystallinity and density further enhance (from 5.11 to 5.60 g/cm3) by increasing the rf power value used during in situ Ar plasma annealing process. X-ray photoelectron spectroscopy (XPS) measurement of the ß-Ga2O3 sample grown under optimal in situ plasma annealing power (250 W) revealed near-ideal film stoichiometry (O/Ga of ∼1.44) with relatively low carbon content (∼5 at. %), whereas 50 W rf power treated film was highly non-stoichiometric (O/Ga of ∼2.31) with considerably elevated carbon content. Our results demonstrate the effectiveness of in situ Ar plasma annealing process to transform amorphous wide bandgap oxide semiconductors into crystalline films without needing high-temperature post-deposition annealing treatment.

Low Thermal Budget Heteroepitaxial Gallium Oxide Thin Films Enabled by Atomic Layer Deposition.

This work explores the applicability of atomic layer deposition (ALD) in producing highly oriented crystalline gallium oxide films on foreign substrates at low thermal budgets. The effects of substrate, deposition temperature, and annealing process on formation of crystalline gallium oxide are discussed. The Ga2O3 films exhibited a strong preferred orientation on the c-plane sapphire substrate. The onset of formation of crystalline gallium oxide is determined, at which only two sets of planes, i.e., α-Ga2O3 (006) and ß-Ga2O3 (4̅02), are present parallel to the surface. More specifically, this work reports, for the first time, that epitaxial gallium oxide films on sapphire start to form at deposition temperatures ≥ 190 °C by using an optimized plasma-enhanced ALD process such that α-Ga2O3 (006)∥α-Al2O3 (006) and ß-Ga2O3 (2̅01)∥α-Al2O3 (006). Both α-Ga2O3 (006) and ß-Ga2O3 (2̅01) planes are polar planes (i.e., consisting of only one type of atom, either Ga or O) and, therefore, favorable to form by ALD at such low deposition temperatures. Ellipsometry and van der Pauw measurements confirmed that the crystalline films have optical and electrical properties close to bulk gallium oxide. The film grown at 277 °C was determined to have superior properties among as-deposited films. Using TEM to locate α-Ga2O3 and ß-Ga2O3 domains in the as-deposited crystalline films, we proposed a short annealing scheme to limit the development of α-Ga2O3 domains in the film and produce pure ß-Ga2O3 films via an energy-efficient process. A pure ß-Ga2O3 phase on sapphire with ß-Ga2O3 (2̅01)∥α-Al2O3 (006) was successfully achieved by using the proposed process at the low annealing temperature of 550 °C preceded by the low deposition temperature of 190 °C. The results of this work enable epitaxial growth of gallium oxide thin films, with superior material properties offered by ALD, not only with potential applications as a high-performance material in reducing global energy consumption but also with an energy-efficient fabrication process.

Investigation of the Physical Properties of Plasma Enhanced Atomic Layer Deposited Silicon Nitride as Etch Stopper.

Correlations between physical properties linking film quality with wet etch rate (WER), one of the leading figures of merit, in plasma-enhanced atomic layer deposition (PEALD) grown silicon nitride (SiN x) films remain largely unresearched. Achieving a low WER of a SiN x film is especially significant in its use as an etch stopper for technology beyond 7 nm node semiconductor processing. Herein, we explore the correlation between the hydrogen concentration, hydrogen bonding states, bulk film density, residual impurity concentration, and the WERs of PEALD SiN x using Fourier transform infrared spectrometry, X-ray reflectivity, and spectroscopic ellipsometry, etc. PEALD SiN x films for this study were deposited using hexachlorodisilane and hollow cathode plasma source under a range of process temperatures (270-360 °C) and plasma gas compositions (N2/NH3 or Ar/NH3) to understand the influence of hydrogen concentration, hydrogen bonding states, bulk film density, and residual impurity concentration on the WER. Varying hydrogen concentration and differences in the hydrogen bonding states resulted in different bulk film densities and, accordingly, a variation in WER. We observe a linear relationship between hydrogen bonding concentration and WER as well as a reciprocal relationship between bulk film density and WER. Analogous to the PECVD SiN x processes, a reduction in hydrogen bonding concentration arises from either (1) thermal activation or (2) plasma excited species. However, unlike the case with silane (SiH4)-based PECVD SiN x, PEALD SiN x WERs are affected by residual impurities of Si precursors (i.e., chlorine impurity). Thus, possible wet etching mechanisms in HF in which the WER is affected by hydrogen bonding states or residual impurities are proposed. The shifts of amine basicity in SiN x due to different hydrogen bonding states and the changes in Si electrophilicity due to Cl impurity content are suggested as the main mechanisms that influence WER in the PEALD processes.

Hollow Cathode Plasma-Enhanced Atomic Layer Deposition of Silicon Nitride Using Pentachlorodisilane.

In this work, a novel chlorodisilane precursor, pentachlorodisilane (PCDS, HSi2Cl5), was investigated for the growth of silicon nitride (SiN x) via hollow cathode plasma-enhanced atomic layer deposition (PEALD). A well-defined self-limiting growth behavior was successfully demonstrated over the growth temperature range of 270-360 °C. At identical process conditions, PCDS not only demonstrated approximately >20% higher growth per cycle than that of a commercially available chlorodisilane precursor, hexachlorodisilane (Si2Cl6), but also delivered a better or at least comparable film quality determined by characterizing the refractive index, wet etch rate, and density of the films. The composition of the SiN x films grown at 360 °C using PCDS, as determined by X-ray photoelectron spectroscopy, showed low O content (∼2 at. %) and Cl content (<1 at. %; below the detection limit). Fourier transform infrared spectroscopy spectra suggested that N-H bonds were the dominant hydrogen-containing bonds in the SiN x films without a significant amount of Si-H bonds originating from the precursor molecules. The possible surface reaction pathways of the PEALD SiN x using PCDS on the surface terminated with amine groups (-NH2 and -NH-) are proposed. The PEALD SiN x films grown using PCDS also exhibited a leakage current density as low as 1-2 nA/cm2 at 2 MV/cm and a breakdown electric field as high as ∼12 MV/cm.

Gas Diffusion Barriers Prepared by Spatial Atmospheric Pressure Plasma Enhanced ALD.

In this work, we report on aluminum oxide (Al2O3) gas permeation barriers prepared by spatial ALD (SALD) at atmospheric pressure. We compare the growth characteristics and layer properties using trimethylaluminum (TMA) in combination with an Ar/O2 remote atmospheric pressure plasma for different substrate velocities and different temperatures. The resulting Al2O3 films show ultralow water vapor transmission rates (WVTR) on the order of 10-6 gm-2d-1. In notable contrast, plasma based layers already show good barrier properties at low deposition temperatures (75 °C), while water based processes require a growth temperature above 100 °C to achieve equally low WVTRs. The activation energy for the water permeation mechanism was determined to be 62 kJ/mol.

Atomic Layer Deposition of Silicon Nitride Thin Films: A Review of Recent Progress, Challenges, and Outlooks.

With the continued miniaturization of devices in the semiconductor industry, atomic layer deposition (ALD) of silicon nitride thin films (SiNx) has attracted great interest due to the inherent benefits of this process compared to other silicon nitride thin film deposition techniques. These benefits include not only high conformality and atomic-scale thickness control, but also low deposition temperatures. Over the past 20 years, recognition of the remarkable features of SiNx ALD, reinforced by experimental and theoretical investigations of the underlying surface reaction mechanism, has contributed to the development and widespread use of ALD SiNx thin films in both laboratory studies and industrial applications. Such recognition has spurred ever-increasing opportunities for the applications of the SiNx ALD technique in various arenas. Nevertheless, this technique still faces a number of challenges, which should be addressed through a collaborative effort between academia and industry. It is expected that the SiNx ALD will be further perceived as an indispensable technique for scaling next-generation ultra-large-scale integration (ULSI) technology. In this review, the authors examine the current research progress, challenges and future prospects of the SiNx ALD technique.