Hard beta and gamma emissions of 124I. Impact on occupational dose in PET/CT.

AIM: The hard beta and gamma radiation of 124I can cause high doses to PET/CT workers. In this study we tried to quantify this occupational exposure and to optimize radioprotection. METHODS: Thin MCP-Ns thermoluminescent dosimeters suitable for measuring beta and gamma radiation were used for extremity dosimetry, active personal dosimeters for whole-body dosimetry. Extremity doses were determined during dispensing of 124I and oral administration of the activity to the patient, the body dose during all phases of the PET/CT procedure. In addition, dose rates of vials and syringes as used in clinical practice were measured. The procedure for dispensing 124I was optimized using newly developed shielding. RESULTS: Skin dose rates up to 100 mSv/min were measured when in contact with the manufacturer's vial containing 370 MBq of 124I. For an unshielded 5 ml syringe the positron skin dose was about seven times the gamma dose. Before optimization of the preparation of 124I, using an already reasonably safe technique, the highest mean skin dose caused by handling 370 MBq was 1.9 mSv (max. 4.4 mSv). After optimization the skin dose was below 0.2 mSv. CONCLUSION: The highly energetic positrons emitted by 124I can cause high skin doses if radioprotection is poor. Under optimized conditions occupational doses are acceptable. Education of workers is of paramount importance.

Blocking the saphenofemoral junction during ultrasound-guided foam sclerotherapy-- assessment of a presumed safety-measure procedure.

OBJECTIVES: Ultrasound-guided foam sclerotherapy (UGFS) is a technique in which a mixture of sclerosing drug and gas is used to treat varicose veins. Several authors have demonstrated transient systemic effects after UGFS. These effects are not well understood but probably originate from a systemic distribution of the sclerosing foam. Therefore, safety measures have been developed to prevent foam from flowing into the deep venous system. The aim of the study is to evaluate whether blockage of the saphenofemoral (SF) junction by either manual compression or surgical ligation prevents microbubbles from leaking into the deep venous circulation. METHODS: To detect the distribution of microbubbles, radioactive pertechnetate (99mTcO4-) was added to the foam solution. Initially, in vitro trials were performed in the laboratory to investigate the effect of 99mTc on foam stability. The time taken for foam to liquefy was measured for foam alone and for the mixture with 99mTc. In subsequent research, eight varicose great saphenous veins (GSVs) were treated by UGFS. In three patients, this treatment was preceded by surgical ligation of the SF junction. In three patients, the groin was manually compressed during UGFS. In two patients, UGFS was performed without compression of the groin. RESULTS: In vitro, 99mTc did not influence foam stability; after 2.6 min all foam had reduced to liquid, regardless of whether 99mTc had been added or not. In vivo trials showed that all patients showed a decrease in the cumulative amount of 99mTc detected in the GSV following polidocanol-99mTc mixture injection. However, the decrease of radioactivity was slightly reduced when compression or ligation of the SF junction was performed. CONCLUSIONS: Blocking the SF junction during UGFS using either manual compression or ligation does not prevent, but may reduce the flow of foam into the femoral vein.

Quantitative performance evaluation of 124I PET/MRI lesion dosimetry in differentiated thyroid cancer.

The aim was to investigate the quantitative performance of 124I PET/MRI for pre-therapy lesion dosimetry in differentiated thyroid cancer (DTC). Phantom measurements were performed on a PET/MRI system (Biograph mMR, Siemens Healthcare) using 124I and 18F. The PET calibration factor and the influence of radiofrequency coil attenuation were determined using a cylindrical phantom homogeneously filled with radioactivity. The calibration factor was 1.00 ± 0.02 for 18F and 0.88 ± 0.02 for 124I. Near the radiofrequency surface coil an underestimation of less than 5% in radioactivity concentration was observed. Soft-tissue sphere recovery coefficients were determined using the NEMA IEC body phantom. Recovery coefficients were systematically higher for 18F than for 124I. In addition, the six spheres of the phantom were segmented using a PET-based iterative segmentation algorithm. For all 124I measurements, the deviations in segmented lesion volume and mean radioactivity concentration relative to the actual values were smaller than 15% and 25%, respectively. The effect of MR-based attenuation correction (three- and four-segment µ-maps) on bone lesion quantification was assessed using radioactive spheres filled with a K2HPO4 solution mimicking bone lesions. The four-segment µ-map resulted in an underestimation of the imaged radioactivity concentration of up to 15%, whereas the three-segment µ-map resulted in an overestimation of up to 10%. For twenty lesions identified in six patients, a comparison of 124I PET/MRI to PET/CT was performed with respect to segmented lesion volume and radioactivity concentration. The interclass correlation coefficients showed excellent agreement in segmented lesion volume and radioactivity concentration (0.999 and 0.95, respectively). In conclusion, it is feasible that accurate quantitative 124I PET/MRI could be used to perform radioiodine pre-therapy lesion dosimetry in DTC.

Baseline and postcaptopril renal blood flow measurements in hypertensives suspected of renal artery stenosis.

UNLABELLED: Renal blood flow (RBF) measurements using first-pass radionuclide angiography with DTPA, a glomerularly filtered agent, failed to show significant differences between normal and stenotic kidneys. Since MAG3 is an ideal agent for the study of RBF, this agent might be an attractive alternative tracer to detect differences in RBF. METHODS: An angiographically controlled prospective study was performed in 48 hypertensive patients, in whom a diagnosis of renovascular hypertension was suspected on clinical grounds. The study was done to determine whether RBF measurements using first-pass radionuclide angiography with 99mTc-MAG3 could be helpful in the diagnostic work-up of the patients. Additionally, the study was done before and after ACE-inhibition. RESULTS: On renal angiography, 29 patients showed to have normal renal arteries (50 patients had normal kidneys and 8 patients had small kidneys). Nineteen patients had renal artery stenosis (13 uni- and 6 bilateral disease). In the patients with normal kidneys, the mean value of RBF measurements ranged from 10.5% to 10.9% of cardiac output. Only small stenotic and small kidneys with normal renal arteries showed a significant reduced baseline RBF as compared with normal kidneys (both p < 0.05); this difference disappeared after ACE-inhibition only for the small kidneys with normal renal arteries. In patients with stenosed kidneys, RBF tended to be reduced both at baseline and after captopril, but the differences with normal kidneys were not statistically significant. After ACE-inhibition RBF increased in the majority of kidneys, but postcaptopril RBF data did not differ significantly from those at baseline. CONCLUSION: RBF measurements using first-pass radionuclide angiography with 99mTc-MAG3, either before or after ACE-inhibition, cannot reliably discriminate between patients with essential hypertension and patients with renal artery stenosis.

Patient dosimetry of intravenously administered 99mTc-annexin V.

UNLABELLED: Annexin V labeled with 99mTc is evaluated as a potential in vivo marker for tissue with increased apoptosis. Promising results in patients have been obtained with 99mTc-(n-1-imino-4-mercaptobutyl)-annexin V (99mTc-i-AnxV). Because information on biodistribution and radiation burden is desired for the application of any radiopharmaceutical, a dosimetric study of 99mTc-i-AnxV was undertaken. METHODS: Eight persons with normal kidney and liver functions were included in this study: six patients with myocardial infarction, one with Crohn's disease, and one healthy volunteer. Approximately 600 MBq 99mTc-i-AnxV were injected intravenously immediately before a dynamic study with a dual-head gamma camera in conjugate view mode. In the next 24 h, two to four whole-body scans were acquired. Patient thickness was determined from a transmission scan with a 57Co flood source. Organ uptake was estimated after correction for background, attenuation, and scatter, using a depth-independent buildup factor and an organ-size-dependent attenuation correction. Residence times were calculated from the dynamic and whole-body studies and used as input for the MIRDOSE 3.1 program to obtain organ-absorbed doses and effective dose. RESULTS: Activity strongly accumulated in the kidneys (21% +/- 6% of the injected dose at 4 h postinjection) and the liver (12.8% +/- 2.2%). Uptake in the target tissues (myocardium or colon) was limited and negligible from a dosimetric point of view. The biologic half-life of activity registered over the total body was 62 +/- 13 h. Of the excreted activity, approximately 75% went to the urine and 25% to the feces. The absorbed dose for the more strongly exposed organs was (in microGy/MBq): kidneys, 93 +/- 24; spleen, 22 +/- 6; liver, 17 +/- 2; testes, 15 +/- 3; thyroid, 10 +/- 6; urinary bladder wall, 7.5 +/- 2.6; and red bone marrow, 5.5 +/- 0.8. The effective dose was 9.7 +/- 1.0 microSv/MBq, corresponding to a total effective dose of 5.8 +/- 0.6 mSv for a nominally injected activity of 600 MBq. CONCLUSION: 99mTc-i-AnxV strongly accumulates in the kidneys and to a lesser degree in the liver. The associated effective dose per MBq is in the midrange of values found for routine 99mTc-labeled compounds. From a dosimetric point of view 99mTc-i-AnxV is therefore well suited for the study of apoptosis in patients.

The effect of a single rectal dose of cisapride on delayed gastric emptying.

BACKGROUND: Cisapride has an established prokinetic effect in patients with delayed gastric emptying. However, rectal administration of the drug might be preferred in patients with either dysphagia or nausea due to gastroparesis. AIM: To determine the effect of a single rectal dose of cisapride 60 mg on gastric emptying in patients with delayed gastric emptying. METHODS: Thirty-two patients (16 males, 16 females) with demonstrated delayed gastric emptying received a single dose of two suppositories containing either cisapride (2 x 30 mg) or placebo, according to a double-blind randomized crossover design. Three hours after administration of the suppositories, the patients received a radio-labelled test meal and radio-opaque markers for measurement of gastric emptying. RESULTS: The mean t1/2 after cisapride administration (76 min, 95% CI: 68-95) was significantly shorter (P = 0.005: n = 28, per-protocol analysis) than after placebo administration (104 min, 81-126). Four hours after ingestion of the meal significantly fewer radio-opaque markers remained in the stomach after cisapride than after placebo administration (P < 0.05). Mild to moderate adverse events, mainly involving the gastrointestinal tract, were reported in 10 patients (31%) after cisapride treatment and in four patients (13%) after placebo (N.S.: n = 32). CONCLUSION: A single suppository dose of cisapride 60 mg significantly accelerates gastric emptying of the solid phase of a meal and of radio-opaque markers in patients with previously demonstrated delayed gastric emptying.

Beta-adrenergic stimulation and abdominal subcutaneous fat blood flow in lean, obese, and reduced-obese subjects.

The present study was designed to investigate whether the beta-adrenergically mediated blood flow response of abdominal subcutaneous adipose tissue (per unit adipose tissue weight) was altered in obesity and to study the effect of weight reduction on this response. Body composition (underwater weighing) and fat blood flow were determined in a group of lean (n = 9; % body fat, 11.6 +/- 3.9) and obese (n = 9; % body fat, 28.3 +/- 1.8) subjects. In seven obese subjects, measurements were also performed after a 4-week period of weight reduction induced by a very-low calorie diet (% body fat after diet 23.4 +/- 3.3). After an overnight fast, abdominal subcutaneous fat blood flow was determined by the 133xenon washout technique during a 30-minute period of supine rest and during 30-minute periods of infusion of the beta-agonist isoprenaline (ISO) with and without simultaneous infusion of the beta 1-blocker atenolol (AT). Basal abdominal fat blood flow was significantly higher in lean as compared with obese subjects, whereas weight reduction significantly increased basal fat blood flow (obese v reduced-obese, P < .05). There was a significant increase in abdominal fat blood flow as a result of ISO infusion in lean and obese subjects before and after weight reduction. During ISO+AT infusion, abdominal fat blood flow was still significantly increased as compared with control values in lean and obese subjects. The increase in blood flow during ISO was significantly higher in lean subjects than in obese subjects, whereas the ISO+AT-induced blood flow response was comparable.(ABSTRACT TRUNCATED AT 250 WORDS)

The CT's sample volume as an approximate, instrumental measure for density resolution in densitometry of the lung.

Ultimately CT-densitometry of the lung should give comparable results on all scanners. One prerequisite for this is the use of the same density resolution. Unfortunately, density resolution is impractical as a performance specifying parameter because it depends on the cellular material scanned. Therefore, another parameter that can be used for scanner and protocol characterization, and that does not depend on a special phantom, would be highly preferable. We investigated how well the CT's nominal sample volume (V), calculated from section thickness and in-plane spatial resolution as specified by the CT manufacturer, can serve as a simple measure, for density resolution. Six CT scanners were studied using foam and lung phantoms. On all scanners we observed for foam an approximately linear relation between density resolution and V-1/2. Density resolution on different scanners varied to some extent. These differences can be interpreted as being caused by deviations of the true sample volume from the nominal value: the 95%-confidence interval runs for instance for V = 8 mm3 from 4.6 mm3 to 16.9 mm3. Acceptability of this spread depends on the consequences for parameters of clinical interest, like percentiles and pixel indexes. To evaluate this we used data from a previous patient study on the dependence of histogram parameters on sample volume. With these data it is found that large interscanner differences in histogram parameters are possible for small values of V, as used in thin-section densitometry. For larger values of V, as required for a more adequate density resolution, the differences are much smaller and probably acceptable when compared to other sources of variability in lung densitometry. In conclusion, for sections of at least 2 mm and smooth reconstruction filters, corresponding to V > or = 8 mm3, the CT's nominal sample volume might be used for interscanner and interprotocol comparison of density resolution.

On segmentation of lung parenchyma in quantitative computed tomography of the lung.

Our purpose in this study was to investigate the influence of segmentation threshold and number of erosions on parameters used in quantitative computed tomography (CT) of the lung (erosions are shrink operations on the segmented area). Parameters assessed were mean lung density, area of the segmented lung, two percentiles, and the pixel index, which is the relative area of the histogram below -905 Hounsfield Units (HU). We analyzed images of ten emphysematous and ten nonemphysematous patients, that had been scanned at carina level in inspiration and expiration, using sections of 1, 2, 3, 5, and 10 mm in combination with a standard, a smooth, and an ultrasmooth reconstruction kernel. The lungs were segmented using pixel tracing at thresholds of -200, -400, and -600 HU with 0-4 erosions, followed by histogram analysis. The area of the segmented lungs decreased with 0.9%-3.2% per 100 HU decrease in threshold and with 2.2%-3.1% per erosion, dependent on patient group and respiratory status. Estimated mean lung density changed up to 30% by changing the threshold and the number of erosions. The pixel index and the 10th percentile depended only slightly on threshold and number of erosions, but the 90th percentile showed a strong dependence of up to 40%. It is concluded that the segmentation protocol can have a large impact on densitometric parameters and that standardization is mandatory for obtaining comparable results. Ideally a threshold equal to the average of the densities of lung and soft tissue should be used, but -400 HU will do in a limited but common density range (-910 to -790 HU). For densitometry two erosions are recommended, for volumetry zero erosions should be used.

Density resolution in quantitative computed tomography of foam and lung.

This study was performed to assess density resolution in quantitative computed tomography (CT) of foam and lung. Density resolution, a measure for the ability to discriminate materials of different density in a CT number histogram, is normally determined by quantum noise. In a cellular solid, variations in mass in the volumes sampled by CT cause an additional degradation of density resolution by the linear partial volume effect. The sample volume, which is directly related to spatial resolution, can be varied by choosing different section thicknesses and reconstruction filters. Several polyethene (PE) foams, as simple models of lung tissue, and five patients were investigated using various sample volumes. For the uniform PE foams, density resolution could be directly determined as the full width at half maximum of CT number histograms. Density resolution for foams with cell sizes of 0.8-1.5 mm was dominated by effects caused by the limited sample size, not by quantum noise. The relative magnitudes of density resolution could roughly be explained with a model for a hypothetic random cellular solid. Since lungs are not of uniform density, analysis of patient data was more complicated. A combined convolution least-squares fit procedure, together with information obtained in the studies of foam, were used to determine density resolution in lung studies. Density resolution, both for foams and lung, was strongly dependent on sample volume, and was quite poor for thin sections and sharp filters. Consequently, histogram-shape related parameters are sensitive to the spatial resolution chosen on CT. Thin section densitometry, using a 1-mm section with a standard or high resolution filter, is not recommended except in determining average density. When using thicker sections, an in-plane spatial resolution similar to section thickness is advised.

The nonlinear partial volume effect and computed tomography densitometry of foam and lung.

A quantitative study was performed to assess the magnitude of the nonlinear partial volume effect (NLPVE) in computed tomography (CT) densitometry of polyethene foam and lung. This effect arises in materials having density variations on the scale of the sampling area of an individual CT-detector element. It causes a systematic underestimation of the density determined with CT. Foam samples and a resected lung of a goat were imaged with high resolution (20 lp/mm) using a mammography system, and the observed optical density variation in the images was converted into a distribution of pathlengths that x rays penetrate within the solid component of the cellular material. The obtained pathlength distribution was used to calculate the transmission, as seen by a single detector in computed tomography. Comparison with the transmission through homogeneous material of the same thickness gave an estimate of the NLPVE. For the foams studied, the CT-determined density was found to be too low by approximately 0.3%-0.5% due to this effect. Although these density errors are small, in calibrations of a CT scanner they may be of significance. For lung the underestimation of the density was less than 0.1%. These experimentally derived, NLPVE related CT-density errors are 32%-84% of those calculated from a simple model of a cellular solid.

Patient dosimetry in abdominal arteriography.

This study aims at accurate quantification of x-ray exposure and effective dose to the patient in abdominal arteriography. Using an automatic monitoring system, all relevant exposure parameters were determined during 172 abdominal arteriographies. Common projections were extracted for a 'normal' reference group of procedures and used in Monte Carlo calculations of dose-area product to organ dose conversion coefficients. Dose-area product, organ doses and effective dose were quantified for intravenous and intra-arterial procedures. The large data sets describing exposure could be condensed to a set of 28 common views. New coefficients to convert dose area product to organ equivalent dose and effective dose were calculated for nine views contributing approximately 80% to the total dose-area product. The average dose-area product was 32 Gy cm2 in intravenous procedures and 47 Gy cm2 in intra-arterial procedures. The corresponding average effective doses to the patient were 4 mSv and 6 mSv respectively (range 2-12 mSv, actual value depending on procedure type and gender). It is concluded that automatic monitoring of x ray exposure parameters, complemented by the calculation of Monte Carlo organ dose conversion coefficients, is a feasible and promising approach to accurate dosimetry of complex arteriographic procedures.

Patient and occupational dosimetry in double contrast barium enema examinations.

A new and relatively simple method is presented to distribute total dose-area product (DAP) over a number of projections that model exposure during double contrast barium enema (DCBE) examinations. In addition, hitherto unavailable entrance and effective doses to the physician performing the DCBE examination have been determined. DAP, fluoroscopy time, number of images as well as some patient data were collected for 150 DCBE examinations. For a subset of 50 examinations, the distribution of DAP over 12 hypothetical but representative projections was estimated by measuring the entrance dose in the centre of each of these projections during the complete procedure. Effective dose to the patient was obtained using DAP to effective dose conversion coefficients calculated for each of the 12 projections. Exposure of the worker was quantified by measuring the entrance dose at the forehead, neck, arms, right hand and legs. The sex-averaged effective dose to the patient per examination was 6.4+/-2.1 mSv (mean+/-SD; n=50) and the corresponding DAP was 44+/-22 Gy cm(2). The effective dose to the worker per examination was 0.52 microGy (n=50), whereas the highest entrance dose of 30+/-25 microGy was found for the right arm. The proposed method for deriving the distribution of total DAP over a set of representative projections is much less time consuming than visual observation of patient exposure, whilst accuracy seems acceptable. Entrance and effective doses per examination for workers in DCBE examinations are very low. For a normal workload, doses remain far below the legally established dose limits.

The effect of equipment set up on patient radiation dose in conventional and CT angiography of the renal arteries.

Patient radiation dose in angiography of the renal arteries was assessed and optimized after installing new radiological equipment. In three separate studies (n=50, 25 and 20) patient exposure was monitored in detail. For the first study default factory settings were used, for the second the number of digital subtraction angiography (DSA) images was halved and the X-ray beam filtering during fluoroscopy was increased, and for the third study filtering during DSA was increased as well. Standard projections were derived and used in Monte Carlo simulations to derive dose conversion coefficients to calculate effective dose from the dose-area product (DAP). Dose conversion coefficients were also calculated for CT angiography (CTA). Using default factory settings on the new angiography system, DAP, number of images and effective dose were much higher than on the replaced unit. For the studies given above, DAP was reduced from 144 Gy cm(2) to 65 Gy cm(2) to 32 Gy cm(2), and effective dose from 22 mSv to 11 mSv to 9.1 mSv, respectively. Effective dose due to CTA was 5.2 mSv. It is concluded that modern angiography systems, resulting in high customer satisfaction, may readily cause much higher patient exposure than older systems. These doses may also be much higher than necessary. Optimization before putting such systems into use is absolutely essential. Internationally accepted recommendations for image quality and technique factors in angiography would be of great help.

Comparison between human pharmacokinetics and imaging properties of two conjugation methods for 99mTc-annexin A5.

Annexin A5 (AnxA5) is a protein with high affinity for phosphatidyl serine, a phospholipid exposed on the cell surface during apoptosis. This phenomenon has been used for determination of cell death after myocardial infarction. To evaluate the potential of (99m)Tc-AnxA5 for in vivo scintigraphy of apoptotic cells, the pharmacokinetics and imaging properties of two radiopharmaceuticals, (99m)Tc-(n-1-imino-4-mercaptobutyl)-AnxA5 (I-AnxA5) and (99m)Tc-(4,5-bis(thioacetamido)pentanoyl)-AnxA5 (B-AnxA5), were studied. I-AnxA5 was administered intravenously to seven patients and one healthy volunteer, and B-AnxA5 was administered to 12 patients. All patients in the pharmacokinetic study had myocardial disease. Additionally, imaging was performed in a patient with acute myocardial infarction, as well as in three patients with different malignancies. The plasma concentration, excretion and biodistribution of (99m)Tc-AnxA5 were measured, as well as levels of AnxA5 antigen. The kinetic data of both radiopharmaceuticals in plasma fitted a two-compartment model. Both preparations had similar half-lives, but a different distribution over the two compartments. Plasma levels of AnxA5 antigen showed a broad variation. Both radiopharmaceuticals accumulated in the kidney, liver and gut. B-AnxA5 was excreted significantly faster than I-AnxA5. Both compounds can be used for imaging of the head/neck region, the thorax and the extremities. B-AnxA5 has a faster clearance and a lower radiation dose. Imaging of apoptosis in the abdomen will be difficult with both radiopharmaceuticals, and especially with B-AnxA5 because of its faster appearance in the gut.

Vascular radiology in The Netherlands in 1992: a quantitative approach.

A survey was held into methods and extent of vascular radiology in the Netherlands. For the year 1992, quantitative data on the number of patients, vascular radiological examinations and characteristics of angiography facilities were obtained from more than 80% of the Dutch hospitals with angiography rooms (120). The following estimates have been inferred: approximately 50,600 patients were referred for non-cardiac vascular radiology, including 32,100 patients for intra-arterial arteriography, 8900 for intravenous DSA arteriography, 4600 for phlebography and 5000 for interventional radiology. On average about two vascular examinations were carried out per patient referred for arteriography. In interventional radiology, the number of patients and the number of examinations are quite similar. The total number of angiography rooms in the Netherlands was 136. The average age of angiography X-ray systems was 7.1 years, of imaging equipment 5.7 years. In 56% of the hospitals, the X-ray tube was normally applied in the undercouch position, in 40% in overcouch position and in 4% there was no preferred position. An additional survey of occupational exposure conditions in angiography rooms (19 hospitals) showed that, in most hospitals, protective lead aprons of 0.5 mm Pb-equivalent were in use. Thyroid collars were used rather infrequently.

Radiation dose in defecography.

The effective dose equivalent, as an expression of total patient risk for exposure to limited areas of the body, and gonadal doses associated with hereditary effects were estimated in 67 consecutive subjects (43 women and 24 men) who underwent defecography. With use of measured entrance exposure values and data from Monte Carlo simulations, the mean effective dose equivalent was estimated at 4.9 mSv +/- 1.6 (490 mrem +/- 160) for women and 0.6 mSv +/- 0.2 (60 mrem +/- 20) for men. The ovarian dose was 15 mSv +/- 5 (1.5 rem +/- 0.5). The testes are not within the primary beam and therefore are exposed to scattered radiation only, hence the low received dose of 0.14 mSv or less (14 mrem or less). These data indicate that defecography is among the radiologic procedures associated with a considerable, but not extreme, radiation dose.

On the generation of short-axis and radial long-axis slices in thallium-201 myocardial perfusion single-photon emission tomography.

We tried to develop fully automatic reorientation algorithms in thallium-201 myocardial perfusion single-photon emission tomography, and tested a method to evaluate the quality of reorientation. The left ventricle was automatically segmented using count density information, contours generated with Laplacian operators in both transaxial and sagittal slices, and morphological and positional characteristics of the contours. Reorientation was automatically performed based on knowledge of the long axis of a second degree surfac fitted to the myocardial wall. We tried to achieve improvement in reorientation without relying on any functional description of left ventricular shape. Quality of reorientation was evaluated and improved using interactive tools in combination with radial long-axis slices. Two groups of 50 patients, after stress and rest, were analysed using the traditional manual and the fully automatic procedures. Automatic segmentation was successful in 98 out of 100 cases, and automatic reorientation was of reasonable quality. Reorientation obtained with the radial long-axis slices tool was better than after traditional manual or automatic reorientation. Automatic reorientation based on second degree surface fitting was in our hands less successful than reported in the literature. The tool using radial long-axis slices provides a better standard for testing reorientation algorithms than the traditional manual method.